MacBook Pro A1260 will not be in service 9/10 times

Similar Questions

• My macbook pro battery will not hold a charge

  My macbook pro battery will not hold a charge. I took in an Apple reseller and claimed him install a new battery. He said that my battery was still good. I asked him to install a new battery just to have a brand new machine. With the new battery installed, the computer still will not hold a charge for very long. I got the Apple dealer and he ran several tests without conclusive results. I always have a laptop that will not hold a charge and must be connected to use for any period of time. Can anyone offer a solution? Thank you.

  Try a reset of the SCM.  System sometimes forget the management of his own material. Reset the management system (SCM) controller on your Mac - Apple Support

• MacBook pro 2012 will not identify new SSD

  I just bought a macbook pro of 2012 and have used it for two weeks without flaws with my 250 GB samsung SSD drive. Now I tried to update the size and bought myself a Corsair Force THE 480 GB to use as the primary drive. I plugged it in, but the mac does not recognize the drive. So I formatted with another mac and tried again. Still no luck. Tried the old drive. No luck with that one or the other. So I knew the data cable from being broken. But when I plug a normal HARD disk it recognizes when in the main location. So the question is, what is the problem with the mac? I don't understand.

  And help will be greatly appreciated

  happyandconfused wrote:

  I plug a regular HDD when it recognizes in the main location.

  What is a HDD or SSD Samsung rotation?

  Have you plugged the SSD (both) external via USB and will the boot the MBP?

  When you have the SSD inside, can I none, one or two boot the MBP?

  Ciao.

• Macbook Pro retina does not illuminate

  Hi all

  I have a 2015 13 "Macbook Pro, that will not start at all. Last night I came back after a day holiday and powered to the top of my Macbook for the first time in two weeks. The battery level was around 25%, so I plugged the magsafe and did some navigation / watching Youtube. I noticed the GET a little slow mac and a youtube video stutter a bit, but it was late so I was not too concerned and put the Mac to sleep mode by closing the lid.

  This morning, after waking up, I noticed that the magsafe light was still orange, which seemed strange to me as he did pay for one night for a good 10 hours. I opened the cover, but the mac does not wake up. I pressed the power button and the computer booted. At first, everything seemed OK but the computer seems slow and internet soon.

  As the bright light battery was still orange that I flew over the battery icon, which showed 100%. I unplugged the magsafe and he fell immediately to 0%, so I reconnected it. I went to make a diagnosis, however about 20-30 seconds later the computer shuts down.

  Since then, he failed to power to the top of all and nothing I have try works. I tried to hold the power button down, but nothing. There is no edge and the caps lock button is not illuminated, so I know that is not a problem of display.

  I left the magsafe plugged in for 4 hours, and it's still orange.

  I have reset the SMC. While this life Magsafe turns green for a few seconds, and then turn the orange back.

  I tried an another magsafe, which is the same, so I've reduced that as a problem.

  I spoke to Apple support, who say it could be the battery and take it to an Apple store. My most close is a 150 miles round trip, and there is no reserves for the next 8 days. I'm sure this will be a hardware problem, but everyone does not accept that it is likely to be the battery? I did have problems with the battery before it and the charge went really well. Would not the Mac boot always if there was a problem with the battery while it is still plugged into the mains?

  Any help or insight is greatly appreciated

  There could be several reasons why your macbook pro turns on.  Just throw the grounds up into the air and choose one.

  Apple stores are not the only places that repair of the Macs.

  APSP (Apple Premium Service Provider)

  International of the APSP and other Services

  APSP outside of the USA

  How to find your nearest Service Premium Apple supplier (DAD)

  

• Updated the MacBook Pro to ElCapita to Apple's Service. Now cannot restore last July 7 from Time Machine backup. Help, please.

  Updated the MacBook Pro to ElCapita to Apple's Service. Now cannot restore last July 7 from Time Machine backup. Help, please.

  Visit Time Machine FAQ of Pondini helps with Time Machine. It is a vast site with almost everything that you need for using Time Machine. You will not find a better resource for Time Machine in one place. Due to the disappearance of James Pondini is the site is no longer updated. Therefore, some information may be somewhat outdated.

• MacBook Pro (2014) does not charge despite an orange light when plugged

  Hello

  So my 2 year old Macbook Pro (retina) does not load when it is plugged in - spite, projecting the orange light. I have a battery (20%) and it is reduced whenever I use it and will be soon drained.

  Some of the things I've tried

  -Reset SMC - tried but no change after

  -When I use the mac when it is plugged in the battery icon in the top bar done see the support - but there is no increase in % of the battery. Continuous use it starts to fall.

  -During use (and what battery is plugged) - I checked the report system (about this Mac section) - in the energy sector - it is said does not charge (despite being connected, the orange light and the symbol in the top bar)

  What do you think guys that it is? MLB? Battery?

  What I have to replace or can it be fixed?

  If you have the Apple store, take the machine evaluation.  There is no charge for this, but you need an appointment.   The first thing I would check would be the cable.  You have another machine to test this with.

• File Manager XP PRO SP3 will not recognize USB floppy A: drive

  File Manager XP PRO SP3 will not recognize USB floppy A: drive

  The system tray alerts "new hardware found" and "installed".

  In the system. material | Device Manager | floppy drives, the disk is present, activated and works

  If I pay BACK the drive is located and can be read and written.

  The drive is not the case in (windows explorerer file manager.

  The drive is not present in administrative tools. computer management | storage | removalable storage | libraries.

  In the removable storage service is started.

  If bottom line, the usb floppy is a material recognized, works under DOS, but there is no access to XP.

  This happens with two floppies different usb connected directly to a laptop (not a hub). When connecting to another XP computer, the disks are immediately recognized in the file manager and work as expected.

  Any ideas?

  It's embarrassing, BUT I solved the problem by using TweakIU. It seems that in the workstation. The floppy drives were not verified. Verification of A & B readers did the trick.

• Apple MacBook Pro 2012 does not start

  2012 Apple MacBook Pro.  Does not start.  Just get the folder with the question mark.  gives possibility to restart with the ERD, but the model doesn't have a hard drive.

  Help the college student needs to access files on the hard drive for the finals.

  Thank you

  What happens when you start to recovery

  OS X: on OS X Recovery - Apple Support

  and repair/disk startup disk via disk utility which is located in the recovery of aid?

  If it is repairable so reinstall OS x, as the article says

  Also here is covered:

  On the screens, you see when you start your Mac - Apple Support

  This is the Office Mac Pro forum. I asked that your post be moved to the MacBook Pro laptop forum.

• Received a flashing alarm indicating that I had a virus on my MacBook pro.  Could not get rid of it, until I did a hard reboot.  Deemed scan of Malware for Mac software?  All this experience?

  I just got an alarm flashing indicating that I had a virus on my MacBook pro.  Could not get rid of it, until I did a hard reboot.  Deemed scan of Malware for Mac software?  All this experience?

  These alarms are generally scam popups loaded from the Internet and is not caused by malicious software, but you should always look for other odd behavior or unexplained slowness.

  (140573)

• Satellite Pro M10 will not start again and comes up with the error message

  My laptop Toshiba Satellite Pro M10 will not start again and comes up with the error message "load error" when I press the power button.
  The arised problem after installation of the 'symantec system works' and try to restart windows XP Professional to make the installed executable program.

  What can I do to get the notbook again reboot?

  Hello

  Seems that there are problems with the files of GoBack.

  Try to boot in safe mode and remove the Norton System works from your laptop ;)
  If this does not help, you will need to recover the laptop with the recovery CD Toshiba delivered!

  Also I recommend to visit the Symantec support site and to check the solutions to the problem with the Norton System Works programs

  Good luck

• M176n MFP: MFP M176n will not activate Web Services

  I bought two MFP176n and tried to activate Web Services to print remotely. It does not work. The computer, I have access to the Services Web page on the unit IP address and use the button 'enable '. It run and run, but nothing happens. I see by a few points running on the screen on the printer. They're going to infinity.

  As part of attempts, I've updated the firmware of the device - it's now at 20150228. This has not changed the behavior anyway.

  BTW, I also tried DNS manuals with addresses 8.8.8.8 and 8.8.4.4 as suggested in a previous post. No change.

  EPrint from mobile devices (Android and Ipad) worked on the first day, but only when she is on the LAN...

  Hello @andershl,

  Welcome to the HP support forums.

  I understand that your M176n will not allow Web Services.

  I would like to help.

  Personally, I found that the Google DNS works best with inkjet printers.

  For LaserJet, I use DNS of Level3 address.

  Primary: 209.244.0.3

  Secondary: 209.244.0.4

  If Web Services are still not allowing, turn the printer off and disconnect the power supply to the router for about a minute.

  Plug everything back in and turn the printer.

  When the network has emerged again, try to enable Web Services.

• After recommending the bios update, hp dv6131od running xp pro sp3 will not load windows - is there a wa

  After installing an update of the bios recommended on the hp website my dv6131od running xp pro sp3 will not load windows

  Update does not seem to have problems - failure, lack of time for flash, backup, etc.

  boot sequence seems normal (finds it a bootable cd in the drive, etc.), but windows won't load in safe or other mode

  next steps?  is there a way to access the BIOS?

  Thank you

  There is a simple solution to this problem.  The HP Online Crash Analysis Team has finally responded to my email after 34 days.  I had given up hearing from them despite several requests to repeat.

  I had completely disassembled the laptop trying to find the bios setting the jumpers on the motherboard in response to an idea contained in one of the PM, I sent... all to nothing does not...

  OCAT told me to look in the BIOS under "system configuration" for the Native SATA support.  The last update of the BIOS resets this point 'activated', but that only works for Vista & Win 7.  This must be set to "disabled" for XP and previous operating system.

  I hope that this post will save someone having to wait 5 weeks invest hours of work for a solution that took 3 minutes!

• My new HP Officejet Pro 8600 will not analyze superior at 300 dpi of the location of the single document.

  My new HP Officejet Pro 8600 will not scan more than 300 DPI when scanning individual photos on the glass plate. I do not use the document feeder. I use this printer wireless on an iMac and a PC.

  Hello

  You can pass the value of hp scan: launch of the demand application, select the shortcut to scan (PDF or JPG to the left) and change the resolution you want and save.

  This will send down the printer settings. So the next time you scan, the printer uses these settings.

  Good impression.

• Windows Vista Ultimate 64-bit will not be in service

  Windows Vista Ultimate 64-bit will not be in service.

  I read the other posts and have followed the suggestions. Windows does not start without failure, or any other option in the F8 boot options. Next step is to create a disk to repair windows, Dell did not provide a when the computer was purchased. Can work from any vista repair disc, or I need to find one suitable for my windows edition? Where are these on the Microsoft Web site?

  Thank you!

  Thanks for the help. Sorry for the vague information. I was finally able to diagnose memory problems. I have reset the chip memory and repaired the computer by using the option "repair your computer" F8.

  Once again, thank you for the help.

• Vista Ultimate 64 bit will not be in service

  Windows Vista Ultimate 64-bit will not be in service.

  I read the other posts and have followed the suggestions. Windows does not start without failure, or any other option in the F8 boot options. Next step is to create a disk to repair windows, Dell did not provide a when the computer was purchased. Can work from any vista repair disc, or I need to find one suitable for my windows edition? Where are these on the Microsoft Web site?

  Thank you!

  Hi 1357ace,

  Take a look at the answer in thisthread by Michael Murphy. Michael both SpiritX provide good information to do a disk repair and troubleshooting more.

  Dena
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.