MacBook pro 2012 will not identify new SSD

Similar Questions

• My macbook pro battery will not hold a charge

  My macbook pro battery will not hold a charge. I took in an Apple reseller and claimed him install a new battery. He said that my battery was still good. I asked him to install a new battery just to have a brand new machine. With the new battery installed, the computer still will not hold a charge for very long. I got the Apple dealer and he ran several tests without conclusive results. I always have a laptop that will not hold a charge and must be connected to use for any period of time. Can anyone offer a solution? Thank you.

  Try a reset of the SCM.  System sometimes forget the management of his own material. Reset the management system (SCM) controller on your Mac - Apple Support

• MacBook Pro A1260 will not be in service 9/10 times

  Got an A1260 of MacBook Pro which does not start until 9 / 10 times.  When you try to turn it on, the white sleep button flashes, optical drive makes noise, sleep button turn off, pause, turns on, then off again.  No boot chime sound unless it turns on with SUCCESS.  The computer battery died FYI.  The charger is original magsafe 85w.

  I have reset:

  SMC

  PRAM

  Re-seated memory (more info below)

  Removed all memory - let it beeps 10 - with a pause in between each beep.  Signals from the chip firmware is OK.

  Took off the keyboard and clean the computer with my compressor

  Check internal connections

  The first time I have reset the SMC, I was able to start on the first try.  When the computer was fine on the desktop, even though it is warm to the touch.  Memory in system information out like OK.  I checked the hard drive is good, etc..

  If I try to reboot the computer, 9/10 times it will restart It just stops.

  STOCK of 4 GB of memory:

  Went out the 1st module memory in SLOT 1 and it starts.  Do not restart correctly.  Started via the Start button / stop after his stop.  Second attempt to restart the desktop computer has failed.

  Put 2nd module from memory SLOT 2 INTO SLOT 1.  Did not start.  Come the second press, obtained in normal blue Mac screen, then it became black.

  * Removed 2nd module of memory *.

  Put 1 memory module in SLOT 2 - Startup successfully.  Do not restart correctly.  Has not pressed after his stop start to the first power.  Is not starting on the second power in a hurry.  Is No start to the third power in a hurry.

  Put 1 module of memory in SLOT 1 - Startup successfully.  Successful restarting #1.  Successful restarting #2.  Successful restarting #3.

  Replace 1 memory module in SLOT 2.  power button 4 press NO BOOT.

  Replace 1 memory module in SLOT 1.  power button 4 press NO BOOT.

  -

  I think here is the logic board is a failure - a common problem with this model.

  The computer is currently ONE with 1 stick of memory.  I had run it yesterday with both sticks in.  Once I tried to restart it, it wouldn't start up again.

  Purchase of a new Council of logic for this machine is not worth the money.  I'll probably the GPU to reflow.

  Any other suggestions?

  Seems you have to RAM operation.

  Replace RAM OEM or upgrade.

  https://eShop.MacSales.com/shop/Apple/memory/

  In or out of warranty you can get for free a 'Apple Service Diagnostics' OTC test

  Genius of booking http://www.apple.com/retail/geniusbar/

  Online https://getsupport.apple.com/GetproductgroupList.action

  check the warranty https://selfsolve.apple.com/agreementWarrantyDynamic.do

• Apple MacBook Pro 2012 does not start

  2012 Apple MacBook Pro.  Does not start.  Just get the folder with the question mark.  gives possibility to restart with the ERD, but the model doesn't have a hard drive.

  Help the college student needs to access files on the hard drive for the finals.

  Thank you

  What happens when you start to recovery

  OS X: on OS X Recovery - Apple Support

  and repair/disk startup disk via disk utility which is located in the recovery of aid?

  If it is repairable so reinstall OS x, as the article says

  Also here is covered:

  On the screens, you see when you start your Mac - Apple Support

  This is the Office Mac Pro forum. I asked that your post be moved to the MacBook Pro laptop forum.

• MacBook Pro 2012 does not SSD

  Hello

  So a few months ago, I upgraded my MacBook Pro (13-inch, mid-2012, OS X 10.10.5) with a SSD Samsung 850 Evo. Things were much faster and the other Corsair CMSA16GX3M2A1600C11 Apple Mac 16 GB (2x8GB) was also nice.

  One day, the Macbook has no more SSD, start repair of OS X and reinstalling did not help. If at start up the Mac, then applications suddenly crash randomly.

  Strangely, exchanging for 500 GB disk drive factory solves all problems.

  In addition, I can boot OS X from the SSD via USB3, but internally it does not work.

  I tried different SSD from Apple, Sandisk and Samsung, which were to be properly formatted or have OS X installed, but the Macbook simply does not accept them and either shows a blank screen or screen issue/question mark. With a support boot utility disk sometimes recognize them and sometimes not. The internal SATA cable has also been replaced by about 5 different cables, but that has not solved the problem. Replace the RAM, unplug the various components such as Superdrive or Trackpad as well.

  I can use the Macbook Pro normally but being prevented from using a SSD internal is a serious drawback. My next plan is to try the drive Caddy + SSD boot drive solution but somehow I fear that it could also do not work.

  Wouldn't be a kind of failure of the Logicboard? I'm certainly not an expert, but don't really see any other reasons.

  Thanks in advance!

  any SATA enabled the logic board on a MacBook Pro after that 2007 should accept an SSD (I guess that ANY Board with SATA connectors actually are eligible for one SSD)

  You may have damaged something with the Commission or if you are using any 3rd party with the DSS software is might be incompatible.

  Readers work on other computers or is there no option to test this?

• My acer aspire one will not identify new advanced 5G wifi modem. How can I fix it

  The machine of love but just discovered he can't communicate with new advanced5G wireless modem without ethernet cable. Is - fixable? I know this is an older machine but is ideal for travel. I would also like to load windows 10 when they are available for this machine. Help?

  dlomore,

  You must install a new wireless card that supports this connection of 5G, it is not a limitation of the software, in this case.

• T60 will not identify new 2 GB Dimm

  Just a quick question to the community: my thinkpad T60 comes with a module of 512 MB Dimm and I installed a new 2 GB Dimm (alongside the original 512 MB).  The "thinkvantage" information system says I have 1022 mb of installed memory.  Information system control panel windows says I have 2.5 GB.  I downloaded the fancy of the Lenovo Web site utility to tell me what is in each Dimm slot and it says: no support for memory, for the two slots.

  Any ideas on what is happening here?  I tried the DIMMs of switching between the two slots, which seemed to have no effect.  Also tried to Flash the bios, which had no effect.  Moreover, memory is the part number, genuine Lenovo correct (whatever it is worth).

  Thanks a bunch!

  Looks like your laptop is fine, just the ThinkVantage System Info cannot recgonize the memory.  Maybe a ThinkVantage System Info Update will solve your problem.

  The Bios reports 2.5 GB of ram?

  André

• T61p will not identify new SATA drive

  Hello

  I recently bought a drive Seagate Momentus 7200 RPM 320 Gig - http://www.seagate.com/docs/pdf/datasheet/disc/ds_momentus_7200_3.pdf (on sale at Best Buy for $99 - who could resist that?)

  If the disc in the drive Bay, it works perfectly - Vista sees the complete concert 320 and it works without a doubt faster than my main 5400 RPM 160 Gig of support. However, if I install the drive as primary, the laptop does not start at all - the BIOS does not see the drive. I checked in the BIOS - the only SATA setting I have is to toggle between 'AHCI' and 'Compatibility Mode' and in each framework, I get the same result - the BIOS does not recognize the drive.

  Model T61p - 6459-CTO

  Vista Ultimate 32 bit

  Latest available BIOS and system drivers installed

  Any help would be appreciated.

  emotivecto wrote:

  However, if I install the drive as primary, the laptop does not start at all - the BIOS does not see the drive.

  What exactly you are doing when you are installing the drive as primary?

  The symptoms you describe seem to indicate that the disk is not docked in the Bay.

  See you soon,.

  Bill

• Satellite Pro M70 will not identify SD Bluetooth card

  Help, please
  I think that my Toshiba card SDIO Type-B for Bluetooth [ver. 1.2 - PA3370 - SD Card3] became defective, until last week I transmit data to and from my laptop with no problems, but now he won't see the map... Please help, these cards come with a warranty, the card is less than 1 year.
  I also tried the driver update, but in vain. Help

  Concerning
  Richie

  Hello Richie

  I put t know what is the problem with your card, but if you think that the problem is the card itself, try to contact the dealer where you bought the card and ask if he can test it.

  Sorry, but I don t have any other advice for you.

  Good luck!

• Macbook Pro retina does not illuminate

  Hi all

  I have a 2015 13 "Macbook Pro, that will not start at all. Last night I came back after a day holiday and powered to the top of my Macbook for the first time in two weeks. The battery level was around 25%, so I plugged the magsafe and did some navigation / watching Youtube. I noticed the GET a little slow mac and a youtube video stutter a bit, but it was late so I was not too concerned and put the Mac to sleep mode by closing the lid.

  This morning, after waking up, I noticed that the magsafe light was still orange, which seemed strange to me as he did pay for one night for a good 10 hours. I opened the cover, but the mac does not wake up. I pressed the power button and the computer booted. At first, everything seemed OK but the computer seems slow and internet soon.

  As the bright light battery was still orange that I flew over the battery icon, which showed 100%. I unplugged the magsafe and he fell immediately to 0%, so I reconnected it. I went to make a diagnosis, however about 20-30 seconds later the computer shuts down.

  Since then, he failed to power to the top of all and nothing I have try works. I tried to hold the power button down, but nothing. There is no edge and the caps lock button is not illuminated, so I know that is not a problem of display.

  I left the magsafe plugged in for 4 hours, and it's still orange.

  I have reset the SMC. While this life Magsafe turns green for a few seconds, and then turn the orange back.

  I tried an another magsafe, which is the same, so I've reduced that as a problem.

  I spoke to Apple support, who say it could be the battery and take it to an Apple store. My most close is a 150 miles round trip, and there is no reserves for the next 8 days. I'm sure this will be a hardware problem, but everyone does not accept that it is likely to be the battery? I did have problems with the battery before it and the charge went really well. Would not the Mac boot always if there was a problem with the battery while it is still plugged into the mains?

  Any help or insight is greatly appreciated

  There could be several reasons why your macbook pro turns on.  Just throw the grounds up into the air and choose one.

  Apple stores are not the only places that repair of the Macs.

  APSP (Apple Premium Service Provider)

  International of the APSP and other Services

  APSP outside of the USA

  How to find your nearest Service Premium Apple supplier (DAD)

  

• New update will not download on my Macbook Pro 2012

  New update will not download on my Macbook Pro 2012?

  What specific update?

  What exactly happens when you try?

• My SSD is not appear in the menu on the boot disk (macbook pro 2012)

  Hello world.  So I just got the macbook pro 2012 and starts to do-it-yourself work last night.  I took out the optical drive, transferred the existing location HARD disk (w / caddy) and installed an SSD in its place.  Then I cloned the SSD HARD drive.  No problems so far.

  When I went to change the boot drive startup disk preferences is where I ran into a problem.  My original HARD drive is the only projection.  I had the problem in choosing the boot drive during the reboot (the SSD will appear in this menu) and makes it the default value it.  SSD works very well and is now my main boot drive.  However, I still would like to show in startup disk preferences.  Is it possible to do (preferably without erasing the SSD)?

  Thank you!

  Relevant info - I'm running El Capitan and I used SuperDuper! to clone the HARD disk.

  OK, can I have found the problem.  Map of partition of the SSD has been MBR, no GUID.  I deleted it, reformatted and I am re-cloning it now.  I'll post the result (I hope that as a confirmed for another solution which meets with this).

• How do the initialization of the new hard drive in the macbook pro 2012 model

  I can't the initialization of a new WD hard drive in my macbook pro 2012.

  I installed the new drive and restarted with disk Warrior

  and followed the instructions to press option, command-R.

  When I followed the Protocol to download a new OS, disk utility does not see the newly installed

  HD, what to do?

  < published by host >

  Use disk utility to format drives, no Warrior drive

  How to install OS X on an external drive connected to your Mac - Apple Support

  Drives external Mac OS Extended format before using with Aperture - Apple Support

  http://support.wdc.com/knowledgebase/answer.aspx?ID=1362

• Since the update to El capitan OSX 10.11.4 on my Macbook Pro (2012) I can not connect to the app store - ideas?

  Since the update to El capitan OSX 10.11.4 on my Macbook Pro (2012) I can not connect to the app store - ideas? Im not geek so please be gentle!

  Try restarting mode without failure. To restart in safe mode, restart the computer and press on and hold down the SHIFT key until the Apple icon appears. The computer starts more slowly than usual because the disk utility checks the drive. After getting on the desktop launch the App store and try to connect. Successful or not, once you're done, restart normally to exit safe mode.

• I closed my laptop (Macbook pro 2012) screen with a day and immediately after 30-40 minutes his does not starts once again.

  I closed my laptop (Macbook pro 2012) screen with a day and immediately after 30-40 minutes his does not starts once again.

  Hello Varshil07,

  Thank you for using communities of Apple Support.

  If I understand your message, by updating your Mac you have forced stop, or you have closed the lid, and now it does not start.  To start, I suggest that try you to start in safe mode by following the instructions below.  For later use, it's a good idea to not force the computer to shut down or close the lid while it is up to date, because it can cause problems.

  1. Choose the Apple menu > shut down.

  2. After your Mac stops, wait 10 seconds, then press the power button.

  3. As soon as you hear the startup tone, hold down the SHIFT key.

     You must press the SHIFT key as soon as possible once you hear the startup tone, but not before.

  4. Release the SHIFT key when you see the gray Apple logo and progress indicator.

  To exit safe mode, restart your Mac, but no press during the startup.

  OS X El Capitan: start in safe mode

  Have a good.