Making Exhibitor notes

Similar Questions

• Help! OUTPUT AUDIO BACK DECISION-MAKING DOES not!

  Hi, I have a problem with my AUDIO OUTPUT device. I use a M2N68 AM PLUS Asus MBord, all sounds drivers are updated and works OK. but my problem is that I don't hear anything from the speaker. Notification of speaker level icon is bouncing up and down and detect sound but not the speaker output. Another thing is that my DECISION-MAKING of OUTPUT AUDIO BACK not detect plugged or disconnected devices. My realtek on that HD Audio Manager of PANELS of OUTPUT REAR are blurred and only the FAÇADE are active that does not work as well. I hope someone can help. Thank you!

  Hello

  1. If it works well before?

  2 did you change on your computer before this problem?

  3. you receive an error message?

  You can try these steps and see if it works very well.

  Step 1

  I would like to you can check if the rear speakers are disabled and the volume level is fine.  To do this, follow the steps below.

  1. Click on start.
  2. Click on Control Panel and click on sound.
  3. Playback tab, click speakers and click Properties.
  4. Click the levels tab and check if the back entrance is set to mute and uncheck the box.
  5. Select the level to 100% and check if the speaker rear works fine.

  Also, you can try disabling the improvements and check if it helps.

  To turn off the improvements:

  1. access Control Panel

  2. click on its

  3. Select the play tab

  4. Select entry speakers/headphones

  5. click on Properties

  6. Select the tab improvements

  7. disable all improvements

  Step 2

  Try to perform a system restore and see if it works very well

  System Restore: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows7/system-restore-frequently-asked-questions

  Step 3

  If the steps above don't you may need to contact the manufacturer of the computer to verify that the equipment works very well and has to be replaced or the motherboard

  It may be useful

  Concerning

• Æ making does not like original

  I can't seem to make a clip at the same quality as the original.

  Import the video into AE. Drag the item to the icon to a new composition.  Hide a logo and then make. And every time, no matter what the settings, the quality is reduced and there is slight aliasing / pixelation.

  Joint a screenshot shows the setting for the original model.

  Also attached is a jpg showing the original and rendering.

  

  See, this is not necessarily the real attributes of this sequence. It's just how AE to interpret. It is probably correct, but it could be wrong. Try to check the "Preserve edges (best quality only)" in the dialog box interpret images.

  But be aware that, if you see something with correction of the pixel format in a composition that doesn't use square pixels, sometimes things in AE will look a little funky.

• Keyboard in Logic Pro making strange noise

  Recently, I figured out how to use an audio interface for Logic Pro X so that I can record MIDI and hear me during the recording, but the sound I hear is very strange. When I'm not recording, the regular Steinway Piano preset sounds as it contains some very slow tremolo, making some notes sound an octave higher sometimes. However, when I save, the sound plays back perfectly normal. Anyone know how to fix this?

  Data sheet:

  Roland RD - 800 keyboard

  Interface Audio EX Roland Duo-Capture

  Maybe the RD-800 sends on two or more MIDI channels at the same time. To do this, simply save a note and take a look at the Publisher of the event, how many events is recorded.

  Best,

  DaCaptain

• HP Pavilion 15: Battery not charging

  I have a HP Pavilion 15, who began to do not charge the battery. It flows from the power of thin battery, but the battery is not more. I have to run my computer off the AC charger because I need what is left in the battery to start the computer. I had already tried to go through the system diagnostics. It says that the charger is not detected. I tested it and it is turning off the right amount of power, however.

  This is the charge Jack or the motherboard, I'm sorry to say. Decision-making is not expensive but still a repair difficult. The motherboard is expensive and difficult.

• Satellite L300-13R - WLAN does not not on Windows 7

  I am on Windows 7, it can't detect the wireless device, says I need to reinstall the driver, vista and xp driver install it as they say that they do not support my opperating system.

  I currently have to plug an ethernet cable to get internet. I use a Toshiba Satellite L300 - 13R PSLB0E.

  Please could I have help, thank you very much.
  P

  Hello!

  I think that this is not a problem. Windows 7 is only a beta OS and at the moment, the pilot decision-making is not very good.

  You might find some drivers on the site of the factory of the WLAN card. In your case, it should be Realtek.

  Good bye

• Toshiba 39L4333DG: DLNA almost does not work

  Hello

  I'm experimenting with my new L4, but I find THAT DLNA almost does not work.
  TV is connected to my router where my NAS is also wired (100 MB switch).

  First of all, to access the directories with more than one material is sloooooooooow.
  It takes minutes to view folders.

  Secondly, it seems that the TV is incapable of making anything: not my audio files in WMA, not my AVI videos or my JPEG files!

  Is this something normal?
  How can I make this work?

  Thank you!!

  > Secondly, it seems that the TV is incapable of making anything: not my audio files in WMA, not my AVI videos or my JPEG files!
  You should check the user 89 manuals page.
  http://www.Toshiba-OM.NET/LCD/PDF/English/L4333-323950-English.PDF

  Here you can find all the details what file formats are supported by using the network connection or a USB interface.

  Only the jpeg image files are supported using the connection network and Media Player.
  Other files of pictures on TV, you can view by using, for example, USB flash memory stick

  About DLNA:
  I think you should check the configuration of the network, as described on page 39

• Taylor Swift 1989 tour will not play!

  Why will not play around the world of 1989? No matter how long I left to buffering all that I get is a black screen.

  Hello there, hollybackgirl.

  It seems that your iTunes for Windows stops responding or gives a black screen when you try to play the video content with Apple's music featured. The following Knowledge Base article offers some great recommendations for troubleshooting:

  Fix unexpectedly closes or the launch in iTunes for Windows problems

  Before you begin, download and install the latest Windows updates available for your PC, and you ensure that you have the latest version of iTunes.

  Start iTunes in Mode safe

  When you open iTunes in Mode without failure, you isolate the program of any interference caused by plug-ins or scripts not made by Apple. To start iTunes in safe mode, press the Shift and control on your keyboard while you open iTunes.

  You will see a message as iTunes starts which says "iTunes is running in Mode without failure. Visual plug-ins you have installed have been temporarily disabled. »

  If the problem does not occur in Safe Mode, Remove third-party plug-ins.

  Disconnect your computer from the Internet

  Errors by contacting the iTunes Store and other Apple services can sometimes cause problems with startup of iTunes. If you remove the possibility to connect to these services, you can see if these features have problems that must be resolved.

  1. Disconnect your computer from the Internet. For example, Turn off WiFi or unplug your ethernet cable.
  2. Open iTunes.

  If iTunes opens without any problem, update your drivers. If there is still a problem, Contact the Apple Support for a help to isolate errors.

  If there is still a problem, continue below.

  Create a new user account

  Visit the Microsoft Web site to learn how to create new accounts of users for Windows 8, Windows 7, or Windows Vista or Windows XP.

  If you have the same problem in the new user account, go to the systemic issues. If you do not have the same problem, continue to the user's specific questions.

  User-specific questions

  If the problem only occurs in one particular user account:

  Create a new iTunes library to see if the problem occurs in a new library. If you are using a new iTunes Library solves the problem, re-create your old library in your new.
  To return to your original library, close iTunes and then hold down the SHIFT key while you open the program.

  If the problem persists:

  Look for problems with the content files. Audio files can sometimes cause iTunes to quit unexpectedly or stop responding when the program is reading information analysis. To determine which file can cause the problem, follow the steps below:

  1. Quit iTunes.
  2. Navigate to the iTunes folder:
     Windows Vista:C:\users\username\Music\iTunes
     Windows 7 and Windows 8:C:\users\username\My Music\iTunes
  3. Move the file iTunes Library.itl on your desktop.
  4. Open iTunes. Your library will be empty.
  5. Press control and B on your keyboard to open the bar menu of iTunes. Choose file > add folder to library.
  6. Navigate to the folder where your music:
     Windows Vista:C:\users\username\Music\iTunes\iTunes Media

  
  Windows 7 and Windows 8:C:\users\username\My Music\iTunes\iTunes Media
• Choose an artist, album or song to add to the library and drag it into the iTunes window.
• Wait that iTunes to add the item to your library and perform the analysis successfully gapless playback.
• If the search is successful, continue to add songs to your library.
• If there is a problem with one of your files, your problem will reappear once you add it to the library. Is it reappears, repeat these steps, making sure not to add the files that caused the problem.

Systemic issues

1. Find potentially unwanted programs. Malicious software could prevent iTunes to open or shut down unexpectedly. Make sure your security software is up-to-date and scan your system.
2. Try adjusting the settings of your security software. Learn more about how to solve the problems of security software.
3. Make sure that iTunes is installed correctly. Improper installation of iTunes can contribute to a variety of issues. Learn how reinstall iTunes.
4. Update the drivers on your PC. The outdated drivers on your computer can cause iTunes and other applications to behave strangely. Learn how to day the drivers on your computer.

Thank you for being a part of the communities of Apple Support.

See you soon.

• I have a Robin Didital DPF - 710 photo frame, but there was not a usb port, how can I transfer photos from comp to a memory card

  I HAVE A DIGITAL ROBIN PHOTO FRAME DPF-710 FOR WHICH THE CARD MEMORY IS 1.0 GB, THE PROBLEM IS I WOULD ADD MORE PHOTOS ON THE CARD BUT DO NOT KNOW HOW TO IT AS THE IMAGE HAS NO USB PORT AND I WOULD LIKE TO TAKE PICTURES ON MY COMPUTER TO THE MEMORY CARD, COULD YOU PLEASE ME TELL HOW.

  I guess just that your computer has a media player?

  (If no drive media... Connect the device to your PC
  via USB cable and turn on... Reach... Start / computer...
  your camera must be listed with a drive letter.)

  If you go to... Start / computer... media player should
  be recognized as one or more removable disks... it can
  have several drive letters.

  Removable disk (e :))
  Removable drive (g)
  Removable disk (h :))

  Left click the drive letters... When you identify the drive
  Letter for the media player... (it will be the one making
  does not launch a dialog box that says: "Please insert a disk".
  in the drive? ») ...

  Follow these steps...

  Navigate to the folder in which the photos are... Open it and
  Reach... Edition/select all... right click the selected (highlighted)
  Group and from the menu choose... Send to / removable
  Disk?... Or... left, click on a folder and do the same thing.

  Only a limited number of files can be copied to the root
  Directory of the card... if you transfer lots of photos...
  they must be in one or more folders. If you receive one
  error that says: "cannot copy xxxx (xxxx): the directory '.
  the file cannot be created. » .. There's too many files in
  the root directory of the memory card.

  FWIW... the camera may not recognize the photos if they
  have been published in some way, but they will always be on the
  memory card for use by other means.

• Recovery disks did not work! Reinstall bunk! Ideas?

  Hey guys,.

  I had problems freezing during startup on my vaio vgn-aw120j with windows premium 64 bit and couldn't get 30secs without making it not responsive, so I tried to run the startup of the vaio recovery partition repair. Message said that windows could not fix the problem automatically. So I tried of the recovery DVDs I made a few months earlier. Same question. Ran check disk and he said that the main file table has been damaged on the c drive and cannot be repaired. So I used the recovery DVDs to do a fresh install (don't forget it comes to 1 set of 3 DVDs of recovery made from vaio care assistant several months until symptom has shown and is not the 130 MB of recovery disks that you can dl from neosmart.com - which I also tried). I install with the same problem but intensified by getting only windows to start about 1/3 of the time and just freezes on loading for 2/3 screens. Tried to wipe off all the drives and partitions (reset the value of drive to zero and start over). Reinstalled again. Unable to get a boot safe mode at all. The list of driver loading screen freezes before departure. Running windows normally causes gel 100% of the time, usually before the logon screen.

  Currently, I have a recovery partition which does not seem to help (because it is created automatically during the installation), a primary partition with my operating system does not start properly and some DVD that does not correct the problem.

  What should do? Pop $70 for recovery vaio-issued discs, assuming that those I created is corrupt? It's a disc or hard drive controller arm?

  Please help and thank you.

  TM

  If you can not complete the process of recovery using the recovery discs, you need hardware failure. In fact, your description of the original symptoms which highlights. Contact Sony technical support for repair or replacement. MS - MVP - Elephant Boy computers - don't panic!

• Screen on my laptop Windows 8 will not load?

  The home screen on my laptop Windows 8 (Asus) is not at all responsible. The start screen is the page where you have all the applications, and you can customize the background as well giving him different combinations of colors and patterns in different model. My splash screen background color is between clear and dark green. Just as I said, the splash screen does not load. It's been like that since I've been on the phone a few hours ago - this means that none of the app buttons that show the applications load, and when I search apps, nothing will come either. It is only up like green color background, that I mentioned earlier. I'm worried when I go about it tomorrow, I won't be able to go on any of the applications, making me not to go on my laptop at all. What should I do?

  Hi Daniel,.

  Thanks for posting your question on the Microsoft Community forums.

  I understand that the splash screen does not load in your system to Windows 8. However, I would like to know some more information to refine the question and provide you with better assistance.

  1. What exactly happens when nothing loads on the screen? Do you have only a black background or color without any apps?
  2. What is the model No. for your ASUS notebook?
  3. How did you install Windows 8 (a new installation or an upgrade installation)?
  4. You did it any significant hardware or change software on the computer before this problem?

  This issue could be due to various reasons like an incompatible device or a bad installation or because of some corrupted Boot files. If you are unable to boot your system, I would suggest trying the following methods and check if the problem persists.

  Method 1:

  To check if this problem is due to a compatibility issue with external devices, I suggest you to disconnect all external devices and check if the problem persists.

  Method 2:

  If you have the disc to install Windows 8 with you, you can insert the installation disc and enter the Windows recovery environment for auto repair. See the following steps:

  (a) when your computer starts, wait for the logo of the manufacturer check the option of start menu, it will usually F12.

  (b) restart the computer, press the Boot menu option key to enter the boot menu and change the option to boot to DVD rom

  (c) Insert the disc of Windows 8 and restart the computer, it will boot to the Windows recovery environment.

  (d) click on Troubleshooting, advanced option and then click on auto repair.

  Method 3:

  If you have a disk to install Windows 8 with you, then I suggest you to perform a verification of the file system. System File checker (SFC) scan is done to check if there are any corrupt system files that might cause this problem. See the following steps to perform a scan SFC:

  (a) follow the same steps above to enter in the Windows recovery environment.

  (b) click Troubleshooting, then Advanced options , and click command prompt.

  (c) in the command prompt, type the following command: sfc/scannow , and then press ENTER.

  (d) now, to restart the computer.

  (e) check if the problem persists.

  If you are able to start on the screen, then I suggest to try the steps posted by Praseetha K Nair said on November 18, 2012 in the following link:

  Windows 8 start screen and Apps does not

  Warning: When you use system restore to restore the computer to a previous state, the programs and updates that you have installed after this date are deleted.

  Hope this information is useful. Let us know if you need more help, we will be happy to help you.

• MUSE is NOT intuitive!

  I'm new to MUSE (I'm a web developer by profession of 34 years of coding experience).  I am NOT new to Adobe products, I use Photoshop and first on a regular (almost daily).

  So my first 'basic' attempt using Muse (after going through the tutorials and online help) had to enter text on one of my pages.  Pretty simple right?  One would think that this should be the easiest thing to do with any product design.

  I click on the T (same process as I would in Photoshop or Premiere) and click on a region in my page and start typing... what to do?  NO text... I get some "Anchor" box and provide a name for this?   Say what?  Where is my simple text?

  Then I hit to help system (which, for some weird reason, I have to connect again even if was already switched over my CC cloud application that works 24/7 on my desk), 30 minutes later, I'm closer to my goal than when I started.  That aid system is certainly NOT useful.

  So fortunately, my wife comes to the rescue, she uses InDesign before which is what Muse is apparently based on?  She is using the text tool, click and maintains and drag a bounding box, then click the bounding box to type in the text.

  My first thought, how ON EARTH is that intuitive?  I don't know how I intend to text type then why should I first define an area before you begin to type my text (Muse should do this automatically and intelligently to me)?  Once I'm done typing my text, I will have extra work of sizing this bounding box back to adapt to my text?  Why would I ever want to have these additional steps?  Humans don't work that way, programmers of Devil don't work this way (I'm a)... maybe them think Adobe all users come from a non-intuitive process of InDesign?  That still does not justify making intuitive NOT Muse... Why replicate a non-intuitive process?

  Cheers, Rob.

  Hi Robains,

  Here is the link of feature request Adobe Muse where you could express your concerns:
  Ideas for features in Adobe Muse

  If I understand you correctly, you want to click with the text, tool to produce 'the text point' as is commonly used for securities and securities in desktop publishing. With the help of the method 'text area' to press and slide on a block of text to just a few words seems not intuitive for you. I think I agree. As a user of Muse, your concerns are valid, and I hope that you will take the time to make your suggestion in the forum I linked above.

• Why the knife tool does not leave gaps in the form? (CS6)

  When I use the knife on a shapeit tool leaves a space where I cut. First I thought it was just an illusion in the program, but there again I exported the image (both by "save under" in illustrator and 'export' in inDesign). I was making sure not to move the shapeafter I used the tool, so I don't think there should be a reason.

  I tried on different types of forms such as normal circles and more complex shapes. I also tried to start a new file from scratch but with the same result that be the reason? Is there a setting I should be aware of?

  That's what I see in Illustrator:

  

  And that's what the image looks like when saved as pdf (in illustrator):

  

  It also appears even if I placer place in inDesign, then export to PDF.

  EDIT: I don't know if it's important, but the size of the form is approximately an A4 or there is everything.

  Best regards

  SirSkorpan

  Which is caused by anti-aliasing and is a screen problem.

  Turn off anti-aliasing in the preferences and it should be gone.

• El Capitan calendar gray weekends?!

  I saw some other request it work with no responses.   Finally, I upgraded from ML to EC and the only complain I have is that weekends are greyed out on the calendar, making you not notice them.  Many of us work weekends and these are just as important as M - F days.

  Is it possible to change this?  Its very annoying!   Or someone has a link to where we can apply the fix?

  Thank you!

  Lilskye,

  Here is the link of your comments: https://www.apple.com/feedback/calendar.html

  

• Nervous about upgrading to El Capitan

  Hello

  I am currently using OS X 10.8.5 on a Mid 2012 Mac Book Pro.  I have a 500 GB HD and 432 GB available.  My processor is an Intel Core i5 2.5 GHz and I have DDR3 4 GB 1600 MHz memory.

  My question is my browser (Safari 6.2.8) is updated as much as possible with the Mountain Lion and my credit card company wants an updated set browser to access their site, and I don't know there will be others to follow soon as well as social security, Healthcare.gov, etc.  Also I was see the rotation occasionally surfing autour beach ball.  I can't use Google chrome, either as the OS is too old for that as well.  If unfortunately an upgrade is probably in order.  I've never backed up my computer, I know my pain, but to tell you the truth, it seems really complicated and unreliable.  I copied my spreadsheets, music and photos on the big flash drives. I'm NOT super trendy clientele and mostly use my computer to surf the web, pay your bills online and photos and music.

  I have read several threads here about backing up your computer and even of level 1 users they all seem like they know their way around a hard drive, but most seems to be Greek.  Archive or back up or cloning?  really! I read glowing reports for EC balanced with an equal percent of horror stories.  There are still enemies with each new version, but he always puts fear in me.   So here's my concerns and I hope that someone will be willing to help me with questions.  I apologize beforehand for the length, just trying to give as much information as possible.  I hope this is the right forum for this.

  1. once I figured out hard drive external not really "drives" I checked a few Mac ready those off to use with TM, WD and Seagate are most available.  I really useless a backup by the hour of my computer because I do not change that much every day and it seems that you have to leave this plugged in 24/7, which seems to be a pain for a laptop, making it not so portable. In addition, I read to turn off the computer to remove the external hard drive safely.  really? Just do a manual backup to once per week or per month?

  2 would it not be better for me to use a cloning software, so that I can just do a (bootable?) copy of my current operating system and files instead of the hour by hour back ups with time machine?  I don't know if I'm wise enough to understand all this.  I've been to the site Web of Super Duper and they seem useful, but that's another $ 30 on top of $60 for a 1 TB hard drive.

  3. I've read that you should have 2 copies of your back upward.  This means that the right of the external hard drive 2?

  4. do you need Internet to do back ups?  I use my iPhone as a hotspot, but go to my children if I need more long-term WiFi although their isn't super fast like his outing in the glue.

  5. I don't have a ton of applications other than those that the computer came with, but those I have I really want to lose.  Microsoft Office for Mac 2011, Family Tree Maker for Mac v. 2 being the main.  Also my printer is old so I might have to replace it. I checked their compatibility from a link on this forum.  It seems that two of them will not work.  I don't know how to check if my printer model will work with CBS. Simple workaround?  I hate to lose everything if I update.  For some applications you is impossible to pass up to that you upgrade your operating system, but does that mean that I will lose all the old files?

  6. can you have 1 computer but have 2 OS?  El Capitan when I need to do web stuff and mountain lion to use my other applications?  Probably not easy. Or do I have to take out a loan and buy another computer and keep my old for my obsolete applications?

  7. If I have to do this (upgrade) to EC what should be my game plan be?  Everything to make the transition smoother?  In simple terms for a dummy?

  Anyway, if someone wants to help, I admire!

  If you don't want to upgrade your version of OS X, the version of OS X Lion mountain Safari from Apple is more a web browser secure OS X Lion of the mountains of 10.8 and you should stop using this version of Safari.

  OS X 10.8 Mountain Lion receives more updates of security and, in my view, little time goes more to receive new updates of iTunes, either.

  Same problem with Google Chrome and Mozilla Firefox, which ended support for OS X 10.6 - 10, 8.

  Mozilla Firefox has just ended its support of web browser and its last full version, this emitted (ver. 48.0.0), last August for OS X 10.6 - 10, 8 can still be used for some time more.

  https://www.Mozilla.org/en-us/Firefox/desktop/

  OR

  Mozilla continues support of security (of newest web browser feature support) for the web browser Firefox through their program of Firefox ESR, (that you CAN download, install and use) that will continue only security support for Firefox until next April 2017 for OS X 10.6 - 10, 8.

  You can use these versions of the ESR. Ignore the notes support educational/business.

  https://www.Mozilla.org/en-us/Firefox/organizations/FAQ/

  OR

  See SeaMonkey.

  http://www.SeaMonkey-project.org/

  Good luck!