Managed provider: the operation of data protection has failed.

Similar Questions

• The hardware diagnostic tool advises that the SMART short self-test has failed.

  The hardware diagnostic tool advises that the SMART short self-test has failed.

  Is this a problem? What can I do about it?

  Atelier42 wrote: the hardware diagnostic tool advises that SMART short self test failed.

  Is this a problem? What can I do about it?

  Hello Atelier42, this usually indicates that you have a hard disk failure.

  I would like to back up my data as soon as possible, just in case the hard drive breaks down actually.

  You must also make sure that you have the HP Recovery restore set for your system recovery disc in case you do not want to replace the hard drive.

  With this restore HP Recovery disk set, you could replace a defective hard drive and use this disk set to your HP system back as it was when shipped. Then, you could put your data saved on your system.

• Error 'nmapp.exe.unable to locate the component. This application has failed to start because MSVCP 70 .dll is not found"when you connect to the computer.

  Original title:

  Problem: I use DeLL Desktop.When I connect, these messages appear on my screen: nmapp.exe.unable to locate the component. This application has failed to start because MSVCP 70 .dll not found. Re-installing the application may fix the problem. Pls help. Thank you.

  Hello
  1. what version of Windows is installed on the computer?
  2. are you aware of any changes made to the computer, before the show?
  Assuming you have Windows Vista or Windows 7, follow the steps mentioned below.

  Method 1:
  

  Step 1: Perform a boot minimum troubleshooting and check which application reports this error
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135
  Note: once you have determined the problem by using a clean boot procedure, follow step 7 in the article to restore your computer to normal startup.

  Step 2: reinstall the application.
  Uninstall or change a program
  http://Windows.Microsoft.com/en-us/Windows7/uninstall-or-change-a-program

  Method 2:
  Run an analysis of auditor of system files on your computer and check for the issue.
  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7
  http://support.Microsoft.com/kb/929833

  I hope this helps.

• applesyncnotifer has stopped working unable to locate the component that this application has failed to start because corefoundation.dll was not found. Re-install the app

  Original title: applesyncnotifer has stopped working

  pop-up that said, apple syncnotifer.exe cannot locate the component.  This application has failed to start because corefoundation.dll was not found. Re - install the app may fix the problem.

  Hello

  It's all part of itunes

  Uninstall and reinstall itunes

  Follow the information from apple to the link below

  Remove and reinstall iTunes, QuickTime, and other software components for Windows Vista or Windows 7

  http://support.Apple.com/kb/HT1923

  and or ask for their support of itunes

  http://www.Apple.com/support/iTunes/

  Also try the discussions of apple itunes

  http://discussions.Apple.com/category.jspa?categoryID=149

• Unable to access Internet Explorer after installing the Service Pack 3. Get the error of "Data Protection".

  Service Pack 3 problems

  Recently downloaded service pack 3 and cannot get into Internet Explorer 8 as 'Data Protection' will not allow.  Anyone know how to fix this?

  Hi Courtney,

  ·         Are you referring to Data Execution Prevention (DEP)?

  If so, check if turn off DEP support. To do this, follow these steps.

  a. click Start, click run, type sysdm.cpland then click OK.

  b. on the tab Advanced , under performance, click settings.

  c. on the Data Execution Prevention tab, use one of the following procedures:

  ·         Select the check box next to the program that you want to turn off DEP for and then click OK.

  ·         If the program is not in the list, click Add. Navigate to the folder Program Files , search for the executable file of the program (it will have the .exe extension) and then click Open.

  For more information on DEP, see the following article.

  A detailed description of the feature Data Execution Prevention (DEP) in Windows XP Service Pack 2, Microsoft Windows XP Tablet PC Edition 2005, and Windows Server 2003

• Get a Boot Manager error the amount of system memory has changed strike F1 to continue (I have F1 race) or F2 to run the Setup utility

  OT: Sign in

  I got this alert several times before the alert "windows boot manager".

  The amount of system memory has changed (I have more or less?)

  Strike F1 to continue (I have F1 race) or F2 to run the Setup utility

  Dell Dimension 3000 system series

  What should I do? Run the configuration utility

  anconcito

  Irfan:

  1 - no

  2 - Yes

  today after trying 'the memory diagnostic tool' I had the same alert, I clicked on F2, but I did nothing I do not know how

  3 - no

  Hello nacienancon,

  1. don't you make changes to the computer before getting this error?

  2 are you able to boot normally to the desktop when you turn on computer?

  3. have you tried to install any device memory on your computer?

  This problem is related to hardware, I suggest that you contact Dell support to help you better. You can check the links with information below:

  http://support.Dell.com/support/eDOCS/systems/opgx620/en/UG/A02/memory00.htm

  http://support.Dell.com/support/eDOCS/systems/opgx620/en/UG/A02/tools00.htm#wp1114195

  You can follow the technical assistance column for more information.

  Thank you
  Irfan H, Engineer Support Microsoft Answers. Visit ourMicrosoft answers feedback Forum and let us know what you think.

• I am facing some problems with the installation of data protection. Please see below for details

  We use the data protection in our project.  The research that I have done in protecting data, I realized that the FDM adds the data in protected intersections to load the file that is created by FDM via the import process. The problem is that there are actions given in HFM and I get an error that says: "error: load the file cannot contain action data according to user option." I'm pretty sure that some user option (it would be great if you have an idea where I can find this user option) prevents data already present of shares to be loaded via FDM. Have faced this kind of error before? Is there a work around on this?

  Thank you

  Rohit

  Hello

  The user option which is the origin of the problem is 'File Contains Data property'. You must make sure that this load option is enabled when you start loading in FDM process if the dataset that you present must contain data of shares.

  Kind regards

  Simon

• The operation on the (...) file has failed. Windows 7 - 10 VMWorkstation

  Hey vmware community,.

  Today, I have a problem I did not before. I opened my VMware and wanted to start my vm. Suddenly he opened a small error message with this tag in the breast:

  Operation failed on the file "C:\VMWare\Windows XP-000007 - s001.vmdk.

  If the file is located on a remote file system, make sure that the network connection and the server on which resides this disk to work correctly. If the file is saved on a removable medium, link media.

  Select Retry to retry the operation.

  Click Cancel to end this session.

  Select continue to pass the error to the guest operating system.

  When I click Retry, the message opens again.

  When I click on cancel, it stops.

  When I click on continue, the message appears again.

  In the internet I've found solutions for mac systems, but I have a Windows 7 system. And btw, the virtual machine is win xp if it is relevant.

  Can someone tell me what I have to do, to solve this problem?

  Thank you

  BTW. Sorry for my bad English, im German.

  I wouldn't like that
  We had to throw the last snapshot. vdiskmanager r was not able to repair the holes in the graintable

• System startup with the following error: this application has failed to start because BHO. DLL WAS NOT FOUND.

  Original title: APPS

  WHEN I TURN ON MY COMPUTER, A BOX IS DISPLAYED THAT SAYS: "THIS APPLICATION COULD NOT START BECAUSE BHO.» DLL WAS NOT FOUND.

  REINSTALLING THE APPLICATION MAY FIX THIS PROBLEM... The APP IS ie3sh.exe... I DON'T REMEMBER TO UNINSTALL ANYTHING... I have

  THE THING OF RESTORATION WHERE YOU PUT THINGS BACK THE WAY THEY WERE AT A CERTAIN DATE... BUT THAT WAS BEFORE THE

  MORE DATE OLD HE SAID I COULD GO BACK, WHAT HAS NOT HELPED... I ONLY AM NOT COMPUTER SAVVY, SO IF YOU HAVE AN ANSWER, PLEASE

  BREAK IT DOWN STEP BY STEP... P.S. THANK YOU I USE WINDOWS VISTA HOME PREMIUM... AND I INSTALLED ALL IMPORTANT

  UPDATES... I HOPE I'M THIS SENDING TO THE RIGHT FORUM...

  I suggest you to follow the steps below and check if it helps:

  Method 1: Try to boot in safe mode and check if the same problem occurs.

  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  Method 2: If the problem does not exist in Mode without failure, then try to put your computer in a clean boot state.

  By setting your boot system minimum state helps determine if third-party applications or startup items are causing the problem.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or Windows 7:
  http://support.Microsoft.com/kb/929135

  Note: After the boot minimum troubleshooting step, follow step 7 in the link provided to return the computer to a Normal startup mode.

  Method 3: Also try to scan your hard drive for Microsoft Security Scanner, which would help us to get rid of viruses, spyware and other malicious software.

  The Microsoft Security Scanner is a downloadable security tool for free which allows analysis at the application and helps remove viruses, spyware and other malware. It works with your current antivirus software.

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Note: The Microsoft Safety Scanner ends 10 days after being downloaded. To restart a scan with the latest definitions of anti-malware, download and run the Microsoft Safety Scanner again.

  Hope this information is useful.

• Remove the Configuration of data protection

  Database Oracle 10.2.0.4
  
  Before I signed up with this company, they had some consultants take two of their bodies and development of demonstration Data Guard on them. Now they need their instance of development back and I can't get the standby database is opened in read/write mode. I'm fairly certain that the primary database was successfully changed to stand alone. I followed all the steps described in: how to remove safely a Data Guard Broker Configuration [261336.1 ID].
  
  In the case of the day before, I tried:
  SQL > alter database recover managed standby database cancel;
  ALTER database recover managed standby database cancel
  *
  ERROR on line 1:
  ORA-16136: Managed Standby Recovery non-active
  
  That tells me that it is no longer used for recovery... but if I try to open the instance for read and write I get:
  SQL > alter database open, read write;
  change the database open, read write
  *
  ERROR on line 1:
  ORA-16003: standby database is limited to read-only access
  
  I can't find any documentation on how to do it, so the question. How can I tell the day before to start rolling for himself?

  ALTER database recover managed standby dabase finishing strength;
  Change the database for validation at the grade crossing;
  ALTER database open;

• Microsoft Office Picture Manager leaning the operation

  original title; MICROSOFT OFFICE PICTURE MANAGER AND AFTER IN AN ATTEMPT TO TRY AND INSTALL THE LATEST VERSION OF WINDOWS LIVE ESSENTIALS 2012, SA DOES NOT WORK

  I HAD MICROSOFT OFFICE PICTURE MANAGER, AND AFTER AN ATTEMPT TO INSTALL THE LATEST VERSION OF WINDOWS LIVE ESSENTIALS 2012, IS NOT THERE NOW, ALTHOUGH THERE ARE NOW ANOTHER VERSION, BUT ITS NOT SO EASY TO WORK, KINDLY HELP ME FOR THIS VERSION EVEN BACK. Thank you.

  Office Picture Manager is part of the cabinet, in all programs > MS Office folder > tools

  http://Office.Microsoft.com/en-GB/help/about-Picture-Manager-HP001001721.aspx

  Windows Live Essentials includes a different set of applications, it does not replace that indicated under Office Tools

• migration of data store has failed - now there are two vm - one power off?

  I was migrating a vm fw at different stores of data when a failure has occurred. They may have been cancelled or it may have been the fact that our vcenter server has restarted. I don't know if this would have caused this problem.

  In any case, now, two of the VM series two - power and the other copies are turned off. One that is off is the data store b and the virtual machine is the one data store. The strange thing is, shows of b (power off vm) data store which is where the files are located while the virtual machine is on a. When I browse a datastore I cannot find all files... It just hangs. I googled but am stuck.

  See the screenshots for more details. Thanks in advance!

  Edit: finally to load two data warehouses. They both show identical files: vmdk, vmfx, vmsd etc. for the two virtual machines on two data stores. It's weird!

  Edit 2: or vm, on or off, power to the high/off or migrate or remove from the inventory. Both are 'ping' and one that is good though.

  I figured this out. I have ssh was the host of the virtual machine is on (the two virtual machines were on the same hosts). Down to power, I ran the following command "esxcli vm kill process - type = soft - world id = xxxxx."

  That he got the vm to stop. The virtual machine of the same name already powered off then showed as "orphans". I removed the orphan vm of the inventory, the other vm started automatically acknowledgement of receipt, then I deleted the orphan vm of the 2nd data store.

• the interactive logon process initialization has failed. For more details, please see the event log.

  This error appears when I start my computer. I press ok and it does nothing. I tried to go it's the safe mode, repair, backup and insterting the disc. None of this works. I come to the same thing. I don't know how to make sure my cd starts immediately. I can't get into anything on my computer. Please can you help me? my computer is a dell and only 1 year. I contacted dell and they couldn't help me because it was not a hardware problem. its software.

  Look here:

  http://forums.techarena.in/operating-systems/1121072.htm

• Update Manager Upgrade to 5.5.0 u2b has failed

  Hello!

  Version of update 5.5.0.19906 to 5.5.0 U2b Manager upgrade failed with the Error Message: "the Server vCenter is incompatible with the vSphere Vmware Update Manager you install.» Please select a compatible Server vCenter. »

  The upgrade of the vCenter Server works very well. I also found in the log files:

  [installerRunVCCommand, 379]  [VCSERVER] vc = 5.5.0, version version install supported = 5.5.0, version of the api to install supported VC installation brackets 5.5.0, = build number > = 1883858

  [11-11-2014 14:32:58:176 "DEBUG 13184]  [installerRunVCCommand, 288]  Return code [VCSERVER] version check vc = 103

  [11-11-2014 14:32:58:176 "DEBUG 13184]  [installerRunVCCommand, 349]  Return code [VCSERVER] = 103 check vc.

  Thank you much for the help

  Manfred

  You are welcome

  And don't forget to award points for correct or helpful answers.

• White screen then the message ' selected boot device has failed.

  After a normal shutdown last night, that my cell phone went straight to a white screen on back when I turned on.

  I tried to plug and unplug, take out the battery and connecting it to a TV with a HDMI which did not pick up anything.

  After turning off the power on and off several times, there is now a white dash in the upper left.

  I let him down for about 20 minutes before a message saying "the selected boot device is a, press ENTER to continue" that turns off the computer.

  I had the computer 4 days if shouldn't them be anything malfunction already.

  Any help would be appreciated!

  GabbyBlag

  Hello;
  
  Let me welcome you on the HP forums!
  
  I read your post on startup problems and wanted to help.

  You should not have problems with a PC this new.
  
  My suggestion is that you contact the HP customer support to see about maintenance and options at your disposal under warranty replacement.  If HP is unable to repair it, then you should be able to insist on a replacement - no charge!
  
  If you live in the United States or the Canada, details are on this page: http://www8.hp.com/us/en/contact-hp/phone-assist.html#section1
  
  If you live elsewhere, contact details are on this page: http://www8.hp.com/us/en/contact-hp/ww-contact-us.html
  
  NOTE: once you get through, stay on the line until you are finally able to talk to someone ' one - it can take a while!
  
  Good luck
  
  I'm a volunteer and I do not work for, or represent, HP.
  ========================================================================
  If you feel that my suggestions helped you, please click on the thumbs-up symbol to say thank you!
  
  If they helped to solve your problem, please click 'Accept as Solution' to help others find similar information.