MARCH Cisco and Foundry switch integration.

Hello

Is it possible to add foundry devices to the device in MARCH. Would I be able to import specific events and the State of the system?

Thank you

March does not directly support these devices. You will need to create some parsers customized for each message the device. It is not fun (and not having to do that is the main point of a SIM card) but it can be done.

Tags: Cisco Security

Similar Questions

Issue between Cisco and ESX switch

It is a small deployment with an ESX Server running a Windows Small Business SERVER 2003.
ESX server has 2 network cards, previously a NIC was connected to a small FastEthernet Switch netgear and all workstations have been working on it.
I replaced the netgear with a Cisco WS-C2960S-24TS-S and the field still works fine, the problem is that I can't connect to the service console or the VI client from a computer connected to the switch.
I can't ping the IP switch ESX service console and also can not ping the switch since the service console.
Switch and ESX console can ping the Windows Virtual Machine and the virtual machine can ping both of them. Therefore, I can get to the VI client via Wirtual Machine (not the best scenario to manage one of its right VMS ESX host?)
I don't know what the problem is, but it sounds a lot there is a problem with the configuration of port / vlan on the cisco switch.
Can a Cisco expert help out me here?
Here are some details of the configuration.
Port group service Console and the port Vm group do not use no matter what config VLAN on the ESX Server.
CONFIG NETWORK ESX
# esxcfg - NICS - l
Name PCI Driver link speed Duplex MAC address MTU Description
vmnic0 0b: 00.00 bnx2 up to 1000Mbps Full 00: 1a: 64:b6:06:92 1500 Broadcom Broadcom NetXtreme II BCM5709 1000Base-T Corporation
vmnic1 0b: 00.01 bnx2 up to 100 Mbit/s Full 00: 1a: 64:b6:06:94 1500 Broadcom Broadcom NetXtreme II BCM5709 1000Base-T Corporation
vusb0 nickname cdc_ether Up 0Mbps 02: 1a: 64:b6:06:99 half 1500 unknown unknown
# esxcfg - vswitch - l
Switch name Num used Ports configured Ports MTU rising ports
64 6 64 1500 vmnic0 vSwitch0
Name PortGroup VLAN ID used rising Ports
PORTS 0 1 vmnic0 VM GROUP
0 1 vmnic0 Console service
Switch name Num used Ports configured Ports MTU rising ports
64 3 64 1500 vmnic1 vSwitch1
Name PortGroup VLAN ID used rising Ports
BIG POND ADSL 0 1 vmnic1
# esxcfg - vswif - l
Port Group/DVPort IP IP family name address Netmask Broadcast Enabled TYPE
vswif0 Service Console IPv4 192.168.0.100 255.255.255.0 192.168.0.255 true STATIC
# ifconfig
Lo encap:Local Loopback link
INET addr:127.0.0.1 mask: 255.0.0.0
RACE of LOOPING 16436 Metric: 1
Dropped packets: 1310258 RX errors: 0:0 overruns: 0 frame: 0
Dropped packets: 1310258 TX errors: 0:0 overruns: 0 carrier: 0
collisions: 0 txqueuelen:0
RX bytes: 4531037961 (4.2 GiB) TX bytes: 4531037961 (4.2 GiB)
vmnic0 Link encap HWaddr 00: 1a: 64:B6:06:92
RUNNING BROADCAST MULTICAST MTU:1500 metric: 1
Dropped packets: 94579247 RX errors: 0:0 overruns: 0 frame: 0
Dropped packets: 99834049 TX errors: 0:0 overruns: 0 carrier: 0
collisions: 0 txqueuelen:1000
RX bytes: 127899970453 (119.1 GiB) TX bytes: 19056702095 (17.7 GiB)
Interruption: 209 memory: 92000000-92012100
vmnic1 Link encap HWaddr 00: 1a: 64:B6:06:94
RUNNING BROADCAST MULTICAST MTU:1500 metric: 1
Dropped packets: 3585973 RX errors: 0:0 overruns: 0 frame: 0
Dropped packets: 3018690 TX errors: 0:0 overruns: 0 carrier: 0
collisions: 0 txqueuelen:1000
RX bytes: 2304776001 (2.1 GiB) TX bytes: 1021855293 (974,5 MiB)
Interruption: 217 memory: 94000000-94012100
vswif0 Link encap HWaddr 00:50:56:45:43:6 C
INET addr:192.168.0.100 Bcast:192.168.0.255 mask: 255.255.255.0
RUNNING BROADCAST MULTICAST MTU:1500 metric: 1
Dropped packets: 367248 RX errors: 0:0 overruns: 0 frame: 0
Dropped packets: 126300 TX errors: 0:0 overruns: 0 carrier: 0
collisions: 0 txqueuelen:1000
RX bytes: 33905320 (32.3 MiB) TX bytes: 154760077 (147,5 MiB)
vusb0 Link encap HWaddr 02: 1a: 64:B6:06:99
RUNNING BROADCAST MULTICAST MTU:1500 metric: 1
Fall of RX packets: 341442 errors: 0:0 overruns: 0 frame: 0
Dropped TX packets: 0 errors: 0:0 overruns: 0 carrier: 0
collisions: 0 txqueuelen:1000
RX bytes: 26973918 (25.7 MiB) TX bytes: 0 (0.0 b)
CISCO SWITCH CONFIGURATION
Port on which the ESX nic is connected to:
interface GigabitEthernet0/1
switchport mode trunk
switchport nonegotiate
switchport port-security
aging of the switchport port security 2
security violation restrict port switchport
inactivity of aging switchport port-security type
macro description cisco-computer desk
spanning tree portfast
spanning tree enable bpduguard
!
******************************************
CONFIGURATION OF VLAN
!
interface Vlan1
IP 192.168.0.253 255.255.255.0
!
interface Vlan2
Description management Vlan
no ip address
!
interface Vlan10
Test description Vlan
IP 192.168.121.253 255.255.255.0
!
Default IP gateway 192.168.0.1
Any help would be appreciated.
Thank you

I think I've seen this before. I'm not super familiar with this switch, but I think that the problem is with cisco-computer office macro.

Try using the macro switch cisco instead since you are addressing a vSwitch on the other end. You can always check the mac address table and see if your Mac to the vswif (service console) make their appearance. If they are not then appear this is an inconsistency in the port between the Cisco Switch and vSwitch.

Louis

NSX design with cisco UCS/fabric interconnects and Nexus switches

Hi Experts
I am new to NSX design and deployment and working on a project. We deploy NSX for applications of level 4 (web, app, db, DC). I use logic, DLR, ESG and DFW switches. I next we intend to use roads static confusion..
1. do we cover all the VLAN from the virtual to the physical environment? for example mgmt VLAN, level vlans(web,app,db), vxlan transport vlan or it should be only a VLAN specific? which means would be I have set all the VLANS in environment NSX in my physical switching environment?
2 vds? don't we create not only 1 vds initially during the deployment of vcenter or more? Should we take any special consideration while deploying to the deployment of the NSX?
3 static routes - we configure static routes on the DLR and the GSS? Should I use the default routes upstream? on the physical router should we be routing all subnets from virtual environment to the GSS.
4. where and who should create virtual machines? Via vCenter or before the deployment of the nsx NSX?
5. we have a level of domain controller. Should it be part of 3 or separate applications with allow any any rule on DFW?
Thank you
Sam

(1) the VLANs which exist for physical Machines span the logical switch VXLAN NSX in the following cases:
- If the current deployment there are physical Machines in the same Vlan and subnet IP with Virtual Machines. If this common Port Vlan group is migrated to a switch logic VXLAN Backed port group and not possible to change the IP addresses of the virtual machines, and then a bridge DLR (Distributed logical router) works as the conversion between Vlan physical and virtual VXLAN
- If Conversion of P-to-V of the physical Machines continue on this Vlan
VLAN which cover only the virtual machines or virtual local networks which cover only physical Machines must not be delayed.

(2) for the deployment of the NSX, there may be more than 1 dVS or only 1 vDS according to the design. There may be another type of traffic other VXLAN base of virtual machines such as backup, storage, VMotion and the overall design, management, best practices apply here as well. A requirement of the NSX is a common VDS that spans the entire Cluster. For each Cluster, this "common VDS' may be different. Yet once this VDS maybe a separate VDS dedicated VTEP or VTEP features functionality can be added to the existing VDS. It may be best to separate the VTEP vDS.

(3) for the DLR, a default gateway is usually sufficient. If static routes are used, the GSS must then drive by default upstream and the static routes with the next hop of the DLR downstream for the subnets in the subnets IP VM logical switch. On the physical router static route to the VM, but also DLR - ESG logical subnets Subnet switch is required. Management of static routes is easier if route summarization is possible, or if necessary, close to the IP subnets, so it may be a good idea to use the dynamic routing such as Ospf or BGP protocol. There are also features of IP address management in Vrealize and other IPAM solutions if Automation is necessary for large and dynamic environments.

(4) NSX has no functionality in the creation of the VM, it only creates Services network such as switches, routers, Firewalls, Load Balancing. The creation of the part VM continiues the same way as before. A point to note is maybe the logic is created appear as VXLAN named port groups on the VDS. NSX Manager creates groups of ports on the VDS, the only difference is that the name includes VXLAN. The virtual machine is like before added to this group of VXLAN Backed Port settings, or added to the logical switch from NSX Manager interface that appears again as a Plugin for VCenter. VCENTER is so point to create virtual machines and add these VMs to the logic is.

(5) level of domain controller can be a separate layer, or other third party, may be preferable to upgrade separated except 3 applications. Usually, it's the same design without NSX. dFW rules can help protect the domain controller with allowing only ports of the virtual machine or physical Machines being admitted. dFW rules can apply to VXLAN based logical switches NSX so that VLAN based DVS Port groups because it's the kernel module.

Unity double switch integration - licensing question unity 4.0 (3)

Unity double switch integration - licensing question unity 4.0 (3)

The unit was sold as a single IP integration. My client needs Dual Switch with an Ericsson PBX. I received the license key of ORC, and I opened a folder of TAC.

TAC said that the license file will not allow installation double switch integration. The Cisco SE on the account indicates that the license key will allow me to make the integration of the double switch.

Who is right? I heard that the moderator here has all the answers :)

The is correct. Any customer with a license 4.0 can do double switch. You don't need a special permit.

Thank you

Keith

H - HARVEST and local switching issue (LAN)

Cisco documentation indicates that H-REAP is designed for WAN environments, but I'm interested in the use of REAP H and local switching in a LAN environment. Basically want to control and data + auth traffic are separated.

Also because the controller is local that I have to use H-REAP, I can just do local switching?

Does anyone have experience with this? All suggestions, feedback will be much appreciated.

Hi Mohammed;

Yes, local switching is a sub-feature of REAP H so it must be HREAP to local switching.

The only advantage that you find using the local switching without WAN is that you don't need a big connection to the WLC since it will not process the data traffic, so you can plug a port of the WLC only. Depending on how your network look like, enlighten you really the network between APs and WLC, because traffic goes directly from AP to the destination, without transiting by for WLC.

On the other hand, you lose the advantage of having a roaming and similar advantage brought by the WLC couche3 WLC.

Home network and multiple switches

Hi, I put to level my small business network that ran from ports on my Cisco SG100-24 switch. I bought another SG100-24 who will give me the required ports. My question is how best to connect them.

I am currently using modem from my ISP to a router Cisco RV320 24 / first SG100. I see two options a obvious here being just string them or simply each connect to the router as more of an approach to the tree. I also have a 8 switch (SG200-08) port, but not sure that I need more with the new switch 24 ports so it's a "Smart Switch". I guess I am curious to know if there is any advantage to use mini-GBIC combo ports (with or without having to buy the modules) or simply to browse the two switches of the RV320. I also use a WAP 4410 so my current pan is as follows:
1. Port RV320 1-> SG100-24 #1
2. Port RV320 2-> SG100-24 #2
3. Port 3 of RV320-> WAP4410N
4. RV320 4-> server port
I'd appreciate thoughts and suggestions, in particular with regard to the combo Mini GBIC ports.

Hi Jason,

There are a few ways to accomplish the same thing.

1. you can, as Mike has suggested to continue the physical isolation and each of the SG100 place switches VLAN different interconnected via a RV320 router.

2. If you need more ports for one of VLAN perhaps physical isolation is not possible, then you may need to add SG200-08. You can try to disable some settings that can improve performance, such as Hello, Smartports macro, even STP and Green Ethernet.

I hope this helps a little.

Aleksandra

Cisco Nexus 5548UP switch current Version 5.2 (1) N1 (4)

Hi, we are currently have Cisco Nexus 5548UP switch current Version 5.2 (1) N1 (4)

It is not listed as affected version:

Known affected releases:
(5)

5.2 (1) N1(8A)

6.0 (2) N2 (5)

7.0 (3) N1 (0.125)

7.0 (4) N1 (1)

7.1 (0) N1 (0.349)

The fixed versions known as follows:

Known fixed releases:
(7)

6.0 (2) N2 (4.3)

6.0 (2) N2(5A)

7.0 (1) ZN (0.615)

7.0 (5) N1 (0.173)

7.0 (5) N1 (1)

7.1 (0) N1 (0.371)

7.1 (0) N1 (1)

It needs to be updated to the latest versions?

If Yes, what version of the fixed known better adapt our current version

Cisco Nexus 5548UP switch current Version 5.2 (1) N1 (4)

Thank you.

I had the same question, so I opened a folder of TAC to find the version of the software. I was told that the software listed as available in the bug report are versions of NX - custom OS and that there was no version patched for the 5548p. The support engineer also said that the updates of Nexus 5 k should not until November or December. The best advice I could get was to subscribe to the bug report and wait to be notified of an available upgrade.

Firefox is not fully load site Barclaycard of authentication. It load regarding the demand for certain letters in my password but does not load the button 'Submit', so I can't continue with my purchase and I switch to IE8 browser to buy whatever it is ov

Firefox is not fully load site Barclaycard of authentication. It load regarding the demand for certain letters in my password but does not load the button 'Submit', so I can't continue with my purchase and I switch to IE8 browser to buy anything on the internet. Clues?

This has happened

A few times a week

Is a few weeks ago

Your UserAgent string in Firefox is totally messed up by another program that you have installed and Barclays does not know you use Firefox 3.6.6 - it is probably similar to IE 6.0 on this site.
http://en.Wikipedia.org/wiki/USER_AGENT

type of topic: config in the URL bar and press ENTER.
If you see the warning, you can confirm that you want to access this page.
Filter = general.useragent.
Preferences are "BOLD", a line at a time, and then select reset, right click
Then restart Firefox

Cisco and Checkpoint VPN clients on a single PC

Hello

I'm in the following fix:

I had used customer Checkpoint SecuRemote 4.1 SP - 5 VPN in the past.

Now, I have installed the Cisco VPN client version 4.0.4 on my PC to access IPSec VPN for the PIX in our headquarters.

According to Cisco VPN release notes http://www.cisco.com/univercd/cc/td/doc/product/vpn/client/rel404/404clnt.htm#wp1346340 , it should be possible to have clients both Cisco and Checkpoint VPN installed on the same machine.

But I am not able to connect to my PIX, I receive the following error message:

"Secure the complete VPN connection locally by the Client.

Reason 403: failed to contact the security gateway. »

When I'm looking for signs of PC control-> system-> hardware-> device Administration-> network cards, I can see Cisco Systems VPN Adapter disabled.

After you activate manually, I always get the same error when you try to connect to the Cisco VPN client.

After PC restart the Cisco VPN adapter is disabled later.

I tried to uncheck Check Point SecuRemote form my Dial-up connection (bypassing CSCea31192 of bug, but the bug does not affect NAT - T connection which I use).

I noticed the same situation on three different computers, one running Windows XP, both running Windows 2000.

After uninstalling the client Checkpoint completely (including Windows registry manual removal), the Cisco VPN client works very well.

It seems to me, therefore, that there is a profound mismatch between Cisco and Checkpoint VPN clients.

Does anyone know of a workaround?

Thank you

Milan

We had the same problem with some of our users who need to use the two clients to connect to customer sites.

If I remember the cisco client does not start automatically, but the client of checkpoint 4.1 don't.

We by-passed by deleting the registry entry point control that starts the client at startup. fwenc.exe is the entrance and it is in

HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Run

After that make a shortcut to the executable file that is stored in the directory \bin to relevant checkpoint on the client (it is different from NT & 9 client x) and then only start when it is necessary.

Hope that's a help

Problem router Cisco and Checkpoint VPN

Hello

I couldn't establish vp from site to site between cisco and checkpoint. Can you please check the logs?

Thank you.

* 29 sept 08:17:22.627: IPSEC (sa_request):,.
(Eng. msg key.) Local OUTGOING = Y.Y.Y.Y:500, distance = X.X.X.X:500,
local_proxy = 192.168.222.0/255.255.255.0/256/0,
remote_proxy = 10.0.10.0/255.255.255.0/256/0,
Protocol = ESP, transform = esp - aes 256 esp-sha-hmac (Tunnel),
lifedur = 3600 s and KB 4608000,
SPI = 0 x 0 (0), id_conn = 0, keysize = 256, flags = 0 x 0
* 29 sep 08:17:22.631: ISAKMP: (0): profile of THE request is (NULL)
* 29 sep 08:17:22.631: ISAKMP: created a struct peer X.X.X.X, peer port 500
* 29 sep 08:17:22.631: ISAKMP: new created position = 0x88AD1AB0 peer_handle = 0 x 80000004
* 29 sep 08:17:22.631: ISAKMP: lock struct 0x88AD1AB0, refcount 1 to peer isakmp_initiator
* 29 sep 08:17:22.631: ISAKMP: 500 local port, remote port 500
* 29 sep 08:17:22.631: ISAKMP: set new node 0 to QM_IDLE
* 29 sep 08:17:22.631: ISAKMP: (0): insert his with his 88AF7D94 = success
* 29 sep 08:17:22.631: ISAKMP: (0): cannot start aggressive mode, try the main mode.
* 29 sep 08:17:22.631: ISAKMP: (0): pre-shared key found peer corresponding X.X.X.X
* 29 sep 08:17:22.631: ISAKMP: (0): built of NAT - T of the seller-rfc3947 ID
* 29 sep 08:17:22.631: ISAKMP: (0): built the seller-07 ID NAT - t
* 29 sep 08:17:22.631: ISAKMP: (0): built of NAT - T of the seller-03 IDexit
Router (config) #n
* 29 sep 08:17:22.631: ISAKMP: (0): built the seller-02 ID NAT - t
* 08:17:22.631 Sept. 29: ISAKMP: (0): entry = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_MM
* 08:17:22.631 Sept. 29: ISAKMP: (0): former State = new State IKE_READY = IKE_I_MM1

* 29 sep 08:17:22.631: ISAKMP: (0): Beginner Main Mode Exchange
* 29 sep 08:17:22.631: ISAKMP: (0): package to X.X.X.X my_port 500 peer_port 500 (I) sending MM_NO_STATE
* 08:17:22.631 Sept. 29: ISAKMP: (0): a Packet.o IKE IPv4 send

* 29 sep 08:17:32.631: ISAKMP: (0): transmit phase 1 MM_NO_STATE...
* 29 sep 08:17:32.631: ISAKMP (0): increment the count of errors on his, try 1 5: retransmit the phase 1
* 29 sep 08:17:32.631: ISAKMP: (0): transmit phase 1 MM_NO_STATE
* 29 sep 08:17:32.631: ISAKMP: (0): package to X.X.X.X my_port 500 peer_port 500 (I) sending MM_NO_STATE
* 08:17:32.631 Sept. 29: ISAKMP: (0): sending of a CPVPN IKE IPvaccess lists

* 29 sep 08:17:42.631: ISAKMP: (0): transmit phase 1 MM_NO_STATE...
* 29 sep 08:17:42.631: ISAKMP (0): increment the count of errors on his, try 2 of 5: retransmit the phase 1
* 29 sep 08:17:42.631: ISAKMP: (0): transmit phase 1 MM_NO_STATE
* 29 sep 08:17:42.631: ISAKMP: (0): package to X.X.X.X my_port 500 peer_port 500 (I) sending MM_NO_STATE
* 08:17:42.631 Sept. 29: ISAKMP: (0): sending a packet IPv4 IKE...
* 29 sep 08:17:52.627: IPSEC (key_engine): request timer shot: count = 1,.
local (identity) = Y.Y.Y.Y:0, distance = X.X.X.X:0,
local_proxy = 192.168.222.0/255.255.255.0/256/0,
remote_proxy = 10.0.10.0/255.255.255.0/256/0
* 29 sept 08:17:52.627: IPSEC (sa_request):,.
(Eng. msg key.) Local OUTGOING = Y.Y.Y.Y:500, distance = X.X.X.X:500,
local_proxy = 192.168.222.0/255.255.255.0/256/0,
remote_proxy = 10.0.10.0/255.255.255.0/256/0,
Protocol = ESP, transform = esp - aes 256 esp-sha-hmac (Tunnel),
lifedur = 3600 s and KB 4608000,
SPI = 0 x 0 (0), id_conn = 0, keysize = 256, flags = 0 x 0
* 29 sep 08:17:52.627: ISAKMP: set new node 0 to QM_IDLE
* 29 sep 08:17:52.627: ISAKMP: (0): SA is still budding. Attached new request ipsec. (local Y.Y.Y.Y, distance X.X.X.X)
* 29 sep 08:17:52.627: ISAKMP: error during the processing of HIS application: failed to initialize SA
* 29 sep 08:17:52.627: ISAKMP: error while processing message KMI 0, error 2.
* 29 sep 08:17:52.631: ISAKMP: (0): transmit phase 1 MM_NO_STATE...
* 29 sep 08:17:52.631: ISAKMP (0): increment the count of errors on his, try 3 of 5: retransmit the phase 1
* 29 sep 08:17:52.631: ISAKMP: (0): transmit phase 1 MM_NO_STATE
* 29 sep 08:17:52.631: ISAKMP: (0): package to X.X.X.X my_port 500 peer_port 500 (I) sending MM_NO_STATE
* 08:17:52.631 Sept. 29: ISAKMP: (0): sending a packet IPv4 IKE.
* 29 sep 08:18:02.631: ISAKMP: (0): transmit phase 1 MM_NO_STATE...
* 29 sep 08:18:02.631: ISAKMP (0): increment the count of errors on his, try 4 out 5: retransmit the phase 1
* 29 sep 08:18:02.631: ISAKMP: (0): transmit phase 1 MM_NO_STATE
* 29 sep 08:18:02.631: ISAKMP: (0): package to X.X.X.X my_port 500 peer_port 500 (I) sending MM_NO_STATE
* 08:18:02.631 Sept. 29: ISAKMP: (0): sending a packet IPv4 IKE.
* 29 sep 08:18:12.631: ISAKMP: (0): transmit phase 1 MM_NO_STATE...
* 29 sep 08:18:12.631: ISAKMP (0): increment the count of errors on his, try 5 of 5: retransmit the phase 1
* 29 sep 08:18:12.631: ISAKMP: (0): transmit phase 1 MM_NO_STATE
* 29 sep 08:18:12.631: ISAKMP: (0): package to X.X.X.X my_port 500 peer_port 500 (I) sending MM_NO_STATE
* 08:18:12.631 Sept. 29: ISAKMP: (0): sending a packet IPv4 IKE.
* 29 sep 08:18:22.627: IPSEC (key_engine): request timer shot: count = 2,.
local (identity) = Y.Y.Y.Y:0, distance = X.X.X.X:0,
local_proxy = 192.168.222.0/255.255.255.0/256/0,
remote_proxy = 10.0.10.0/255.255.255.0/256/0
* 29 sep 08:18:22.631: ISAKMP: (0): transmit phase 1 MM_NO_STATE...
* 29 sep 08:18:22.631: ISAKMP: (0): the peer is not paranoid KeepAlive.

* 29 sep 08:18:22.631: ISAKMP: (0): removal of reason ITS status of 'Death by retransmission P1' (I) MM_NO_STATE (peer X.X.X.X)
* 29 sep 08:18:22.631: ISAKMP: (0): removal of reason ITS status of 'Death by retransmission P1' (I) MM_NO_STATE (peer X.X.X.X)
* 29 sep 08:18:22.631: ISAKMP: Unlocking counterpart struct 0x88AD1AB0 for isadb_mark_sa_deleted(), count 0
* 29 sep 08:18:22.631: ISAKMP: delete peer node by peer_reap for X.X.X.X: 88AD1AB0
* 29 sep 08:18:22.631: ISAKMP: (0): node-930113685 error suppression FALSE reason 'IKE deleted.
* 29 sep 08:18:22.631: ISAKMP: (0): error suppression node 661004686 FALSE reason 'IKE deleted.
* 08:18:22.631 Sept. 29: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PHASE1_DEL
* 08:18:22.631 Sept. 29: ISAKMP: (0): former State = new State IKE_I_MM1 = IKE_DEST_SA

* 29 sep 08:18:22.631: IPSEC (key_engine): had an event of the queue with 1 KMI message (s)
* 29 sept 08:18:27.559: IPSEC (sa_request):,.
(Eng. msg key.) Local OUTGOING = Y.Y.Y.Y:500, distance = X.X.X.X:500,
local_proxy = 192.168.222.0/255.255.255.0/256/0,
remote_proxy = 10.0.10.0/255.255.255.0/256/0,
Protocol = ESP, transform = esp - aes 256 esp-sha-hmac (Tunnel),
lifedur = 3600 s and KB 4608000,
SPI = 0 x 0 (0), id_conn = 0, keysize = 256, flags = 0 x 0
* 29 sep 08:18:27.559: ISAKMP: (0): profile of THE request is (NULL)
* 29 sep 08:18:27.559: ISAKMP: created a struct peer X.X.X.X, peer port 500
* 29 sep 08:18:27.559: ISAKMP: new created position = 0x85EDF1F0 peer_handle = 0 x 80000005
* 29 sep 08:18:27.559: ISAKMP: lock struct 0x85EDF1F0, refcount 1 to peer isakmp_initiator
* 29 sep 08:18:27.559: ISAKMP: 500 local port, remote port 500
* 29 sep 08:18:27.559: ISAKMP: set new node 0 to QM_IDLE
* 29 sep 08:18:27.559: ISAKMP: find a dup her to the tree during the isadb_insert his 88C1CE60 = call BVA
* 29 sep 08:18:27.559: ISAKMP: (0): cannot start aggressive mode, try the main mode.
* 29 sep 08:18:27.559: ISAKMP: (0): pre-shared key found peer corresponding X.X.X.X
* 29 sep 08:18:27.559: ISAKMP: (0): built of NAT - T of the seller-rfc3947 ID
* 29 sep 08:18:27.559: ISAKMP: (0): built the seller-07 ID NAT - t
* 29 sep 08:18:27.559: ISAKMP: (0): built of NAT - T of the seller-03 ID
* 29 sep 08:18:27.559: ISAKMP: (0): built the seller-02 ID NAT - t
* 08:18:27.559 Sept. 29: ISAKMP: (0): entry = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_MM
* 08:18:27.559 Sept. 29: ISAKMP: (0): former State = new State IKE_READY = IKE_I_MM1

* 29 sep 08:18:27.559: ISAKMP: (0): Beginner Main Mode Exchange
* 29 sep 08:18:27.559: ISAKMP: (0): package to X.X.X.X my_port 500 peer_port 500 (I) sending MM_NO_STATE
* 08:18:27.559 Sept. 29: ISAKMP: (0): sending a packet IPv4 IKE.
* 29 sep 08:18:37.559: ISAKMP: (0): transmit phase 1 MM_NO_STATE...
* 29 sep 08:18:37.559: ISAKMP (0): increment the count of errors on his, try 1 5: retransmit the phase 1
* 29 sep 08:18:37.559: ISAKMP: (0): transmit phase 1 MM_NO_STATE
* 29 sep 08:18:37.559: ISAKMP: (0): package to X.X.X.X my_port 500 peer_port 500 (I) sending MM_NO_STATE
* 08:18:37.559 Sept. 29: ISAKMP: (0): sending a packet IPv4 IKE.
* 29 sep 08:18:47.559: ISAKMP: (0): transmit phase 1 MM_NO_STATE...
* 29 sep 08:18:47.559: ISAKMP (0): increment the count of errors on his, try 2 of 5: retransmit the phase 1
* 29 sep 08:18:47.559: ISAKMP: (0): transmit phase 1 MM_NO_STATE
* 29 sep 08:18:47.559: ISAKMP: (0): package to X.X.X.X my_port 500 peer_port 500 (I) sending MM_NO_STATE
* 08:18:47.559 Sept. 29: ISAKMP: (0): sending a packet IPv4 IKE.

* 29 sep 08:18:57.559: IPSEC (key_engine): request timer shot: count = 1,.
local (identity) = Y.Y.Y.Y:0, distance = X.X.X.X:0,
local_proxy = 192.168.222.0/255.255.255.0/256/0,
remote_proxy = 10.0.10.0/255.255.255.0/256/0
* 29 sept 08:18:57.559: IPSEC (sa_request):,.
(Eng. msg key.) Local OUTGOING = Y.Y.Y.Y:500, distance = X.X.X.X:500,
local_proxy = 192.168.222.0/255.255.255.0/256/0,
remote_proxy = 10.0.10.0/255.255.255.0/256/0,
Protocol = ESP, transform = esp - aes 256 esp-sha-hmac (Tunnel),
lifedur = 3600 s and KB 4608000,
SPI = 0 x 0 (0), id_conn = 0, keysize = 256, flags = 0 x 0
* 29 sep 08:18:57.559: ISAKMP: set new node 0 to QM_IDLE
* 29 sep 08:18:57.559: ISAKMP: (0): SA is still budding. Attached new request ipsec. (local Y.Y.Y.Y, distance X.X.X.X)
* 29 sep 08:18:57.559: ISAKMP: error during the processing of HIS application: failed to initialize SA
* 29 sep 08:18:57.559: ISAKMP: error while processing message KMI 0, error 2.
* 29 sep 08:18:57.559: ISAKMP: (0): transmit phase 1 MM_NO_STATE...
* 29 sep 08:18:57.559: ISAKMP (0): increment the count of errors on his, try 3 of 5: retransmit the phase 1
* 29 sep 08:18:57.559: ISAKMP: (0): transmit phase 1 MM_NO_STATE
* 29 sep 08:18:57.559: ISAKMP: (0): package to X.X.X.X my_port 500 peer_port 500 (I) sending MM_NO_STATE
Router #.
Router #.
* 08:18:57.559 Sept. 29: ISAKMP: (0): sending a packet IPv4 IKE.
* 29 sep 08:19:07.559: ISAKMP: (0): transmit phase 1 MM_NO_STATE...
* 29 sep 08:19:07.559: ISAKMP (0): increment the count of errors on his, try 4 out 5: retransmit the phase 1
* 29 sep 08:19:07.559: ISAKMP: (0): transmit phase 1 MM_NO_STATE
* 29 sep 08:19:07.559: ISAKMP: (0): package to X.X.X.X my_port 500 peer_port 500 (I) sending MM_NO_STATE
* 08:19:07.559 Sept. 29: ISAKMP: (0): sending a packet IPv4 IKE.
Router #.
Router #un all
All possible debugging has been disabled

The log shows main mode setup has failed. See if this helps: http://www.itcertnotes.com/2011/04/ipsec-stuck-in-mmsasetup-and-mmnostat...

Defining a router and 2 switches in a network

Hello!

I have a question, please reply as soon as possbile.

Look, I'm new in routing, just lerning, CCNA Discovery course, there is the problem:

well, I'll put in place a ROUTER and 2 switches, I have set up in terminal:
the end result, we have:
ETH 0/0 (from where internet is coming) - IP - 192.168.100.200
ETH 0/1 (inside the network) - IP - 192.168.80.1

Also, I configured the same way ARP:
Slash rip router (config) #.
slash network (config - router) # 192.168.100.0 / / IF I understand ARP allows data transffer beetween networks and make it visible on the other

slash network (config - router) # 192.168.80.0

now, if the two devices end network (PC), I ping the ping works and the package was sent and received.
!!!! THE PROBLEM IS > why I can't ping (PC0) 192.168.100.201 the 192.168.80.2 (PC1)
the INVESTIGATION period was made.

There are in tie my tracert schema package. Thx for the reply and attention!

you have the default gateway configured on the two PCs?

H - HARVEST in central auth and local switching has any backup auth method?

Hello

In REAP: solution with central authentication and local switching, do we have any fallback, authentication method in the case of the controller failure or WAN link to controller fails. As authentication WPA/WPA2 PSK for LWAPP REAP H in stand-alone mode.

Thank you

Arun

What guarantees do you intend to use?

If you are using PSK, you're fine as the live keys on the AP. So if you lose the controller, customers will always authenticate. If you use 802. 1 X, it's another story.

Client VPN Cisco and Cisco Secure

Cisco VPN client and the VPN from Cisco Secure client free to use with pix firewall software?

Thank you.

Hello

If you have a valid contract to Cisco and you can get the following link:

http://www.Cisco.com/Kobayashi/SW-Center/SW-VPN.shtml

with your CCO login, then you should be able to use these customers at no cost because they are already covered by the contract.

Thank you and best regards,

Abdelouahed

-=-=-

I have items 12 and since switching to Windows 10 I can't print my photos from Elements. Is this version of Elements is compatible with windows 10

I have items 12 and since switching to Windows 10 I can't print my photos from Elements. Is this version of Elements is compatible with windows 10

jacquesd96006740 wrote:

I have items 12 and since switching to Windows 10 I can't print my photos from Elements. Is this version of Elements is compatible with windows 10

If you use version 12 except pour Print, the problem is to know what is special for your printer. I have no problem with version 12 and win 10 on HP and Epson printers.

You can print from applications other than PSE12?

difference between standard and disturbed switch

What is the difference between standard and disturbed switch?
What is locate these files confutation.

Hi friend

See below blogs:Difference is very well explained

http://www.vmwarearena.com/2014/01/vSphere-distributed-switch-part-3.html

http://www.tech-tap.com/2009/05/30/differences-between-vSwitches-and-dvswitches/

MARCH Cisco and Foundry switch integration.

Similar Questions

This has happened

Maybe you are looking for