MATRIX Toolkit for LabVIEW 2012 for LEGO Mindstorms Installer?

Similar Questions

• LabVIEW for LEGO MINDSTORMS and EV3

  LabVIEW for LEGO MINDSTORMS can be used to program the EV3?

  There will be support for the EV3 with LabVIEW to come. Our plan is to be ready in the first half of 2014.

  MINDSTORMS EV3 of LEGO development environment is the only software I know that can be used to program the EV3 brick when it is made available for purchase.

• LABVIEW FOR LEGO MINDSTORMS

  Hello, I need help. Pls help me with motors to control Robots NXT with NXT buttons. I need change the power of the engines with NXT buttons. How do I achieve this function?

  Thank you very much for your answer!

  -In the attachment is the same program but in NXT - G

  The preferred method is always directly connect the wire also, you will need to use it. However, if it is in a different loop, you can write to a shared variable and read it from the second loop.

  http://www.NI.com/white-paper/4679/en/

• Mac for Lego MINDSTORMS toolkits support

  
  

  Too bad.  I found my own answers.  Thanks anyway.

• labVIEW lego mindstorm

  Hi all

  First, I start only using LabVIEW and I am doing a project to use it to program a data acquisition and a Lego MINDSTORMS at the same time.

  I had downloaded LabVIEW 2010 and then fell on a LabVIEW for lego mindstorms. When you download the LabVIEW for Lego Mindstorms, I lost the 2010 edition of LabVIEW. It is very easy to use the mindstorm addition to program the nxt but in my project, I also use a NOR-DAQ and need the Add on DaqAssist also. Would I be better to return to the 2010 edition and try to find an add-on for mindstorms or is it possible to get an add-on daqAssist for labVIEW, lego mindstorms.

  Thank you

  When I do try and add a component, for example the motor1 that a screen that's going through files saying loading and the search if it does not find a file of what he asks me locate an if i cant find and press Cancel! one continues on his search through files. It will appear the end component on the block diagram but the custom of executed program

  HELP > :-(

• How to shorten the execution time of the NXT (TETRIX & MATRIX toolkit) brick

  Hello

  How to shorten the execution time of the NXT brick?

  (TETRIX & MATRIX toolkit, running time)

  The software is 2012 LabVIEW for LEGO MINDSTORMS

  Thank you.

  

  

  Hi 40123157,

  You use the module in an appropriate manner, and there is no simple way to improve the time of loop iteration beyond what you've done. Here are my suggestions:

  (1) the i2c commands take a long time. In your application, it may speed up if you run only move the engine only when the engine speed has changed.

  (2) for this particular example, you do not use the release of the report engine. If this VI does not need to run it can be removed.

  (3) If you need to speed up execution other than that, as a user advanced LabVIEW, you can create a copy of the VI of engines to move and change it as you choose. All you have to to the "DC motors' entry is use cluster to array on the cluster, as shown below. I think you can speed it up by running all the settings before the loop (type sensor and fixed connection configuration), and removing the value of power if you send only the values between-100 and 100.

  (4) drawing on the screen can be slow you down here.

  

• Lego Mindstorms silent installation

  Hello!

  I want silent install edition teacher of Lego Mindstorms Education EV3. But I can't make it work.

  I use the command line: setup.exe having/q /acceptlicenses Yes/r: n

  I used this credit:

  ; --------------------------  How to use this file  ---------------------------------
  ;
  ; To run this installer in silent mode:
  ; 1 change the information below to match your company's information and the installation location.
  ; 2 run: setup.exe /q /AcceptLicenses Yes. Passing the value 'yes '.
  ;    the /AcceptLicenses parameter indicates that you accept the license agreements.
  ;    Alternatively, instead of / q, / QB can be used to run the installer in basic UI mode.
  ; 3. the installation program will automatically restart your system after the installation is complete.
  ;    To prevent the restart using the command line: setup.exe /r: n/q /AcceptLicenses Yes
  ;
  ; For more information on the automation of the installation visit www.ni.com/info and enter the code exdir3 info.

  ; --------------------------  Set feature states  ---------------------------------
  ;    Valid service States are: local, Absent, NoChange, default
  ;    Local - install (on the local hard drive). If already installed leave that he installed.
  ;    Absent - do not install it. If already installed uninstall it.
  ;    NoChange - do not install it. If already installed, leave it installed.
  ;    Default value is equivalent to not register the function in this file. The feature follows its default behavior.
  ;    To install EV3 in student mode, delete the "EV3_EDU_Mode" parameter on line 24 by removing the entire line.

  [Features]
  LEGO_EV3_EDU_Feature.ev3.edu.100 =
  EV3_EDU_Mode.ev3.edu.mode.100 =

  ; -All install directories-
  ; To use the default paths, remove the following section *.

  [Directories]
  LEGO_EV3_EDU_Feature.ev3.edu.100 =

  ; -Set the parameters of the General installation-
  [InstallationType]
  ; uncomment one of the following lines for student vs. teacher install
  DefaultRadioButton = TeacherInstall
  DefaultRadioButton = StudentInstall

  If I add = Local to the syntaxes features, that it returns an error when you attempt to install, saying that it is an incorrect syntax.

  When I install silent with equity, Lego Mindstorm installs students edition.

  If I try to create a new credit memo with /generatespecfile setup.exe, the installation process hangs.

  So what I am doing wrong?

  Apparently this depends on the version you are trying to install, you must therefore take account of this version in the features section.  For example, I was trying to install version 1.2.1 today and it did not work until I did the following:

  LEGO_EV3_EDU_Feature.ev3.edu.100 = local
  EV3_EDU_Mode.ev3.edu.mode.100 = local

  changed to

  LEGO_EV3_EDU_Feature.ev3.edu.121 = local
  EV3_EDU_Mode.ev3.edu.mode.121 = local

  And the installation in silent mode now works correctly.

• 64-bit LEGO Mindstorms NXT pilot

  During the installation of the driver 64 bits for Lego Mindstorms NXT, it stops and I get the following message. "Installation ended prematurely because of an error". Has anyone else had this issue and know a solution.

  Hi Mark Janovetz

  ·         I suggest all the previous version of the drivers associated with the program and then try to install and check if it helps.

  ·         You can even try to install the driver to boot. To help resolve the error and other messages, you can start Windows 7 by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  Steps to perform the clean boot and check if you have the problem.

  i. Click Start, type msconfig in the search box and press ENTER.

  II. If you are prompted for an administrator password or a confirmation, type the password, or click on continue.

  III. in the general tab, click Selective startup.

  IV. under Selective startup, clear the Load Startup items check box.

  v. click on the Services tab, select the hide all Microsoft Services check box, and then click disable all.

  VI. click OK.

  VII. When you are prompted, click restart.

  VIII. after starting the computer, try to install and check.

  See link below: http://support.Microsoft.com/kb/929135

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  i. Click Start, type msconfig.exe in the start search box and press ENTER.

  II. If you are prompted for an administrator password or for confirmation, type your password, or click on continue.

  III. on the general tab, click the Normal startup option and then click OK.

  IV. When you are prompted to restart the computer, click restart.

  Link for more information please refer to: make sure to run older programs in this version of Windows: http://windows.microsoft.com/en-US/windows-vista/Make-older-programs-run-in-this-version-of-Windows

  Thank you, and in what concerns:

  Samhrutha G S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Internet Toolkit for LabVIEW 2012 64-bit

  I have an application which is currently written in LabVIEW 2009. It requires the Internet. I try to open it in 2012 of LabVIEW (64-bit) (using Windows 7 64-bit). LabVIEW 2012 does not find the box at Internet tools since he has been deprecated in LabVIEW 2012, so LabVIEW complains.

  So I downloaded the toolkit LabVIEW 2012 Internet and tried to install it. When the Setup program tries to run, it stops with an error message that says:

  "NEITHER LabVIEW 2012 (32-bit) or more must be installed before installing OR.
  2012 Internet Toolkit LabVIEW. »

  Can someone tell me where I can find the Internet Toolkit for LabVIEW 2012
  (64 bit)?

  Thank you

  -Ray

  Since you seem to understand that the Internet Toolkit has been deprecated, I do not understand your question. There is no 64-bit version of the tool. In fact, it has very few tools that do not have a 64-bit version. In order to use the old, 32-bit version, you must use it with the version 32-bit LabVIEW, as said the message.

• Error Code HDL with CRio RFP generation after update for LabView 2012

  Hello everyone,

  I use a CRio DP Comsoft master/slave module for my communication with a PLC system. The application worked perfectly under LabView 2011. After the update to LabView2012, I got an error message that the HDL Code generation failed. After that I've updated also the Software NI Profibus CRio in Version 1.3, but this n ' t´t solve the problem. The next step was to use the example of project code "CS_cRIO-PB_DP-MasterExample" which was delivered with the new NI CRio Profibus software. Even with this code example, the problem still exists. For detailed information on the configuration and the error message please refer to the screenshot. Any help or idea would be appreciated.

  Jürgen

  Hi Jürgen,

  I looked inside and could reproduce this error. Somehow the compiler with LV 2012 has problems with the coded 8.5.1 Subvi LV. Please use the attached VI and copy it to the following location. (\\Program Files\National Instruments\LabVIEW 2012\vi.lib\addons\Comsoft.lib\cRIO PB)

  Before do you it please close your LabVIEW.

  Then try to compile again.

  Let me know if it still does not. We are currently working on a new installer that will correct this problem.

  DirkW

• need to convert keithley 2500 photodiode double meter driver for labview 2012

  I installed the driver but found could not use it because the driver version is too old.

  Can anyone help to convert so that it could be used in my labview 2012? Thank you very much.

  There is a separate Commission for the versionhttp://forums.ni.com/t5/Version-Conversion/bd-p/VersionConversion of Conversion

• How do we install support for labview 2012 sp1 64-bit

  Hello

  I downloaded and installed Labview 2012 sp1 64-bit and

  the installation requires a drive support.

  Where can I download a dvd for 64-bit Labview support?

  Thank you

  desiko

  You must install the drivers again so that it will install support for the 64-bit version of LabVIEW.

• LabVIEW 2012 has radio for Boolean control button by default

  Using LabVIEW 2012 SP1 at a customer.  Whenever I create a Boolean control or indicator by right-clicking and selecting 'create', the annoying option button appears...  Yes... one in the picture below.  All I want is one of the lights (round or rectangular).

  I know it takes a ridiculous affecting somewhere.  To save time, but especially of frustration, where hell can I change this setting?  I already looked at the Option settings but don't see anything.

  That's what I get:

  

  This is the system default boolean for a reason any crazy.  I learned to curse under my breath and find the prices for the use of system controls.

  Edit: change the style by default to say, modern or classic and it won't happen.  Unless you use the classes so what control you get when you create controls/indicators is a boring montage.

• Third-party licenses and Activation Toolkit for Labview 8.5

  There are any third-party licenses and the Activation Toolkit for Labview 8.5 as LV2010. PLS help...

  I know what you're asking, and in the other thread, said you it was for 2010 only. There is a support for 2009, but not for your old version. Go with the suggested dongle or upgrade your version of LabVIEW.

• LV Report Generation Toolkit for Microsoft Office said "this VI or element belongs to a library that has expired or improperly licensed."

  I downloaded the LV Report Generation Toolkit for Microsoft Office for evaluation with LabVIEW 2010. Examples to help get a lot of errors, including "the Subvi is not executable. You must fix any errors in the Subvi before this can run VI. "and"this VI or element belongs to a library that has expired or improperly licensed. "

  I decided that I wanted to evaluate the Toolbox instead of putting an activation code during installation. Installation went well.

  How can I get the examples from this LV package to run so that I can evaluate it?

  A computer restart was costing the day the day to solve the problem.

  Installation of the toolkit does not have a reboot of the system, but it seems to need i.