MCU/TMS layouts

Similar Questions

• Int TCS with multiway call recording

  Hi team,

  We have a network of C20, VCS, MCU, TMS, TCS.

  We want the user to perform a recording of calls. The procedure we follow is:

  (1) endpoint A calls the end point B

  (2) point endpoint A Endpoint B highlights waiting

  (3) point ending A call recording allias

  (4) end A point selects JoinCalls

  Call failed

  Endpoint one can see the MCU Conference Conference MCU is created on the MCU join fails, but the end point A ends with 2 calls on hold and other assets.

  If we make with the procedure to join the calls with 3 endopoints it works OK.

  Could someone help me shed some light on this issue?

  Kind regards

  Federico

  Hi Federico. Sounds like you using Multiway on VCS and MCU. Is this fair? Now TCS does not support RouteToMc or SIP refer to the transfer. I need to see the SIP to make sure. TCS but currently does not support what I know. You may be able to use the conductor if you have deployed in the environment of the user. I hope this helps.

  VR
  Patrick

  Sent by Cisco Support technique Android app

• Why the MCU is automatically added to the conferences in TMS?

  Info:

  Endpoints: Tandberg 6000 MXP & 95 MXP

  TMS: 13.2.2

  Codian MCU 4510: Software version 4.4

  Tandberg GK: N6.3

  Tandberg BC: Q6.3

  When I create a conference at TMS and want an end point to compose our system to an MCU on another site (confined), the our local MCU is automatically added to the Conference, for some reason any.  For example, if I create a conference with room 123 and number 'Dial Out' external 2222222, TMS adds MCU of our system and forces to compose both room 123 and 2222222, which is totally useless.  This should be simply, what is the endpoint is, a direct line to 2222222.  Why the MCU is being added?  This will use licenses MCU in haste when it is not necessary at all.

  I went through TMS > administration tools > Configuration > General settings, network settings and conference settings and cannot understand why the MCU is added.  If we dial manually, no problem.  My goal is to automate the entire composition, however.

  Pointers?  I put some of the parameters of the TMS > Admin Tools > Configuration > Conference settings below.

  

  Luke

  Hello

  Reduce the bandwidth of conference help? TMS could add a MCU if it detects that one or more participants do not support the bandwidth conference.

  Kind regards

  Kjetil

• TMS 14.3.1 played not well with Codian MCU 4520 - bug?

  TMS 14.3.1

  Codian MCU 4.4 4520 (3.57)

  After upgrading from 14.3 to 14.3.1 MSDS that I find THAT TMS is no longer recognizing the Codian as being registered at a Registrar SIP (VCS - C x7.2.2) and active SIP server address is empty.

  As a result, it is no longer allow me to plan only calls SIP; that is to say:

  

  In the above Conference, participants at the Summit must be either H.323 or SIP, participating below place SIP (JabberVideo customer 'business'), as well as participating number 3 (customer 'free' JabberVideo).

  Before the upgrade, I've always had the choice of SIP, H.323, and if necessary, IP, now I have only the choice of H.323 and where appropriate, IP.

  Curiously, when using multi-way, it will connect to the customer external jabber.com as SIP - SIP, while in a scheduled call, he'll be H.323 - SIP and appeal in the VCS - E it actually displays H.323 - H.323.

  I have no problems with the old MPS800; Active listed address in TMS SIP server as per normal, and I can choose to H.323, SIP and IP.

  So, is this a bug?

  /Jens

  Please note the answers and score the questions as "answered" as appropriate.

  In the MCU configuration.xml, should say something like:

  user_name VCS.example.com"registrar_name =" example.com"="[email protected] / * /"/ >" "

  The field that is empty in your TMS screenshot ("Active SIP server address") must have been populated by proxy_name value in the confiuration.xml that I can see.

  EDIT: looks like we have made a code change in TMS 14.3.1 when it comes to check the address of the SIP server: in previous versions, read and used TMS 'registrar_name', but from 14.3.1, it reads and uses the "proxy_name" instead.

  Kjetil-

• Limit a range of MCU E164 alias in TMS

  Hi all

  I have a port MCU 4501running 4.3 6HD in TMS 13.2.2.  I want to booking of installation using a track of E164 number say 10002 to 10009.  When I created the MCU in TMS it detects that it has 12 ports (6 audio video and 6) and reserve 12 E164 numbers for her!  It is a problem in my scenario that the client was only given 10 numbers to play with 1000 X and I'm reserving for AA 10000 and 10001 for a permanent conference, letting me 8 other usable numbers.  Using a prefix MCU ID 1000 and digital of each conference from 2 I can generate numbers 10000 to 10009 very well.  The problem is that I want more never 1000010, 100011 and 100012 generated that it takes to 6 numbering plan numbers and just used work with CUCM and shortest match composition!

  I saw a MPS in TMS where E164 ports / URI is configurable in TMS, but I can't see a way to limit the range down to a pool of 8 in. for the 4501.  All the fields I want to change in the settings edit view are grayed out.  A look at the MCU itself I can see that you can book ports, but I won't physically be reserved, I just want the E164 alias be limited to a choice of 8 rather than 12.

  Am I missing something obvious here?

  Any ideas or input greatly appreciated

  Gurp

  That's what it should look like:

  

  After 1109, 1110 follows and so on.

  Kjetil-

• By TMS MCU conference number

  Hi all

  We recorded with vcs several MCU Standing Conference, the source of the telephone directory of endpoint is TMS. I am able to discover and manage all the end points of TMS.

  How to display the number of MCU Permanent conference on endpoint through TMS telephone directory? So that users could dial into permanent conference of the directory itself?

  Currently, I have discovered all the endpoints of TMS and its appearance on all telephone directories of endpoint.

  Thanks in advance!

  Bobby

  Hi Bobby

  Create a new source 'manual list type' less manage sources of the telephone directory. Save and add a contact. Type the conference name, add it.

  Now click on the add contact method and write the address you use to dial the Conference. SIP or H323, (E164 alias is H323)

  Save it and go in manage inventories, create a new directory and connect the source you just created. Then click on set on systems and select all the systems you want to see this directory. And save.

  Every endpoint should now be able to compose this conference through the phone book.

  / Magnus

• CUCM + MCU + CISCO TMS integration

  I'm marching integration with MCU 4.5, 10.5 CUCM, sx20 and TMS 14.5

  According with manual bellows

  http://www.Cisco.com/c/dam/en/us/TD/docs/Telepresence/infrastructure/MCU...

  I ve done a Deploying an MCU as a multimedia resource for Unified CM.

  MCU has a SIP trunk with 10.5 CUCM, MCU is recorded as the Conference on the multimedia resource.

  SX20 Conference ad hoc works well with another 7 codecs.

  My question is

  I want to plan conferences by mcu or cisco TMS, but I am not able to do.

  How can I integrate Cisco TMS or planning by MCU?   It s not working not on my side.

  Hello

  Please see the following guide

  http://www.Cisco.com/c/dam/en/us/TD/docs/Telepresence/infrastructure/TMS...

  HTH

  Manish

• Remove the video of TCS in the layout when flow on demand through TMS ' record'

  System information:

  TMS v13.2.2

  TCS v5.2 (configured as a terminal)

  4510 Codian MCU v4.4

  The TCS and the MCU are registered at TMS.  I work on the management of all our calls more centrally by TMS and struggled to integrate the CHT in conferences.  I don't want the black screen of the "registration...". "appears as a participant at the disposal of the participants.  I know these can be configured manually to rule out it, but I want to automate it as much as possible.

  On the MCU, aliases are configured to not send the video to the MCU by default; It silently records in the background.  All conferences configured directly on the MCU without the "help" of TMS call out to all the endpoints - including the alias TCS - and only the video settings are visible.  The content is saved properly.

  When conferences are planned through TMS, however, the TCS alias is composed in just like before, but it also sends a video feed to the MCU - a black screen with "Recording" on this subject.  I tried to call from the system directory and what makes an "external" call, but both give me the same result.  I guess that's because the MCU and TMS do not share the same phone book.  What is the reason?  When this happens, the MCU is not the ability to cut the flow of the CS during the video content.

  Currently, my plan is to have every endpoint called via TMS scheduling and then have my technicians dial to the CS manually after that trial is over.  Automation is my aim, however

  Any help would be great.

  Hello Luke.

  You can very easily cut the video and/or audio from the TCS in your conference.  When you create the reservation in MSD and have your MCU added, go into 'Connection settings' and it should be two boxes on the right-hand side where you can trim the video/audio.

  Try it and let us know.

• Telepresence redundancy-UCS BE6K, UCS TCS, TMS, MCU

  I know I can do BE6K redundancy.

  How about TCS and TMS MCU?

  Is it possible to make redundancy on TCS and TMS MCU?

  Hello

  Grouping of TCS and redundancy

  http://www.Cisco.com/c/en/us/TD/docs/Telepresence/TCS/6_0/administration...

  Redundancy TMS (page 2 of the following link)

  http://www.Cisco.com/c/dam/en/us/TD/docs/Telepresence/infrastructure/TMS...

  Redundancy MCU

  https://supportforums.Cisco.com/discussion/11944401/conductor-redundacy-...

  https://supportforums.Cisco.com/discussion/11706966/does-TP-conductor-Su...

  HTH

  Manish

• Cisco TMS assigns a numeric ID for the MCU Conference Scheduler

  Hey Cisco

  I create a conference planner tms 14.6, the Conference is to create, but the digital ID is not available until this conference began.

  picture attached

  I need see digital ID before.

  I've not being updated to 14.6 TMS, but in 14.4 and I'd be surprised if this had been changed to 14.6, you can specify a system to switch to the MCU, in which case the address is displayed as below in the screenshot;

  mcu2.gif

  

  or, you can find the address by locating the Conference in the conference control center, then place the cursor on the MCU and you should see a small window showing all the relevant address, as seen in the screenshot; below

  MCU.gif

  

  /Jens

  Please note the answers and score the questions as "answered" as appropriate.

• TMS by booking with MCU in cascade

  Hello

  My client has questions about booking TMS, they have 2 microcontrollers (4205,5320), CTS and 14.2 TMS endpoints

  They want to use 5320 as the main rooms for booking, but if the resource on 5320 is not sufficient for the booking then cascade 4205 to increase capacity.

  I found in the admin MSDS distribution routing guide (low cost print routing and better) but I'm not sure this device meet the requirement.

  The Administrator's guide also said "Different MCU models using cascade when manually configure cascade is not supported in Cisco TMS"

  Note it doesn't you different medium cascading of MCUS in TMS is not supported?

  Anyone try this before please advice.

  Thank you.

  Kind regards

  Wassila

  You can't necessarily force TMS to use a 5320 on a 4205. Remember, TMS treats all the ex-codians as the same, so it is not defined which, two bridges, TMS will prefer.

  Also note that MSDS does not automatically cascade; cascading always requires the invention of the user. The user must explicitly choose a distribution algorithm.

  Kjetil-

• Cisco 5320 MCU layout / view

  We recently converted a MPS200 bridge to a microcontroller of 5320 Cisco.  We have multipoint Conference with 8 participants.  The new 5320 MCU automatically selected a layout component 9.

  It is that some of the participants in this appeal cannot see their auto show, as well as other 8 participants. They can switch back and comes between discovers them, and the participant discovers, but can't see both at the same time.

  This issue was addressed after his conversion to the new MCU.  Any advice?

  If you don't want to see for yourself, you will need to check the box.

  Do you see yourself with small squares
  Do not duplicate with small squares

  Please see the documentation for more information

  (taken from the online help you directly on the box (see the info / help buttons at the top of your mcu settings page))

  Do you see yourself with small squares	Prevents the MCU Conference participants their own videos into small tiles of views of the component of variable size (and conferences with the shutters of equal size).	If this option is set, then a participant will never appear in a small window (see auto), even if there is a free small component available.   They can still appear in larger shutters, however, for example, if the development of view is changed manually to show their video.  See understand how to show participants in the page layout view for more details.
  Do not duplicate with small squares	The MCU prevents duplicating large participating pane with small squares.	When you use a view of the Conference with some aspects of some small and large, the MCU will duplicate usually in a small window the video of a participant showed a large glass.  This is done to minimize the commutation of small tiles in response to changes in activity participating in the General pane.  If you prefer not to duplicate the participants into small tiles in this way, select this option.  For more details on view page layouts, see understand how to display the participants for the layout.

  In addition, it is not really clear what they see and how it is different and how they are passed to the page layout

  and how it behaves different for different endpoints.

  Is there a model, such as specific endpoint types, versions of the software, users...

  So maybe you could do some photos or even a short video.

  In addition to all this, I these two checkboxes and telling people to use their local view on their

  point endpoint to see if they need to check if they seem to always good :-)

  Most of the people I spoke to find annoying if they you themselves, especially as the MCU always adds some lag.

• Join TMS MCU fails with "no ip bandwidth...". »

  We are trying to install a telepresence VTC system. We are trying to register the MCU (5320) (4.5) for TMS (14.6). We use a virtual VCS as the doorman. When attempting to add the TMS MCU, we get a warning "no bandwidth set to the system - system has bandwidth IP or ISDN bandwidth..." MSD displays zeros (0) for Ports and bandwidth. We have defined the bandwidth of the MCU on parameters of the H.323 MCU. There must be some little thing that we have not been configured correctly. We rechecked SNMP parameters, parameters H.323, etc. anything.

  Someone at - it have this problem before?

  TIA,

  Mark

  Areas are used in routing when creating the Conference schedules.  You can assign areas after adding points of termination or infrastructure in TMS, or while you are being added to them.  You can read more about which areas are in the TMS administration Guide, starting on pg 46.

  Regarding your MCU, if you are devoid of multimedia ports, it is probably the root cause of the problem.  Cisco have added to them, you'd only you you receive the product similar to how you added the activation keys and encryption.  If you go to the Cisco Licensing Portal, navigate to obtain other licenses > license of telepresence to return, then enter the serial number of the MCU.  It returns all the keys related to this MCU option if media ports were purchased, they should appear on the screen.  You are looking for something that says "L-5300-4PL.

• MCU 8510 - TMS - SX10 (SIP only)

  Hi all

  I have a question where we have a new SX10 which I added to the MSDS and can make calls to a fine. However when I add it to a conference using the MCU it tells me that the connections settings will change, then deletes all the connections in total of parameters. Addition of 10 other endpoints at the same conference without the SX10 and it works fine (although it is trying to connect on H323 which is fine).

  Why when I add the SX10 at the same conference must kill the connection settings for all units and there is no way to change?

  Why can't I just MCU dial the SX10 via SIP only and the rest stay that H323?

  This is what it looks like before you add the SX10 unit

  capture.jpg

  

  It's what happens after you have added the SX10 and select OK to popup its will change the parameters of connection

  Capture1.jpg

  

  Anyone has any idea why?

  I just did some tests, make sure that the endpoint you are trying to add to the Conference has the same allow incoming and outgoing, planning of the options checked in TMS as your MCU.

• TMS, CUCM and MCU

  Hello

  One of our clients have a MCU5320 and it is registered with the CUCM as SIP. Also, they have a VCS + Expressway VCS control for internet calls. Now the customer plans to buy Cisco MSDS management systems and planning conferences. I don't know if we can schedule conferences on the MCU that is registered with the CUCM VCS not only through TMS. Where do I sign the MCU to the VCS to program by MSDS?

  We want to do this because we do not have enough licenses non-traversal appeal with respect to the control of the VCS.

  Kind regards

  Chambers oumar

  Hi Marc,

  If you register with CUCM MCU, you wil not be able to plan the Conference through it. You can use it for ad-hoc conferences.

  However, if you register MCU with VCS, you can use it to conferring both scheduling and ad - hoc MCU.

  However, if you go for TMS, your TMS can also monitor CUCM. I'm not sure benefits.

  It will be useful.

  Thank you

  Saurabh