Cisco 5320 MCU layout / view

Similar Questions

• Configuration of the firewall Cisco Telepresence MCU 5320

  Hi all.

  I searched all the documents of the MCU again, but I found nothing on the ports it uses.

  Help me

  HI Sandra.  The 5320 MCU is the same as 4500 MCU.

  Incoming ports

  • FTP - TCP:21 + transient (dynamic rather than fixed) used TCP ports for passive mode
  • HTTP - TCP:80
  • HTTPS - TCP:443
  • H.323 - TCP:1720 + ephemeral TCP ports for incoming calls
  • SNMP - UDP:161
  • Outgoing calls to H.323 involve ephemeral ports TCP connections TCP TCP:1720 and a certain number of ephemeral TCP ports
  • Outgoing SIP TCP calls involve connections between the TCP ephemeral ports and TCP:5060
  • Outgoing SIP TCP calls involve connections between the TCP ephemeral ports and TCP:5061
  • Outgoing interruptions SNMP are sent the ephemeral ports UDP Port 162
  • Media (including audio and video, FECC messages) are ephemeral ports from ephemeral ports UDP.
  • The products acquired Cisco TANDBERG/Codian and gateway series series Cisco TelePresence allocate the ephemeral ports between 49152 to 65535 *. It is possible to change the ports on which these products receive and establish connections. For example, by default the Codian products Cisco acquired listen port 1720 H.323 calls and connections to port 80 web browser, but these can be modified (go to network > Services).

  Keep in mind this MCU does not support the streaming or conference me and have either the GK aboard.  If these ports are listed.

  The link to the Article can be found here:

  http://www.Cisco.com/en/us/docs/Telepresence/infrastructure/articles/conferencing_products_conferenceme_ports_used_kb_3.shtml

  VR

  Patrick

• 5320 MCU Sip settings

  I want to deploy 5320 MCU as multimedia cm unified using this resource guide (page 36). But I did not 'Use the trunk' option on page settings_sip.html webUI. I also have access to an another 5320 MCU with the same set of function keys, where this option is available. Only difference between the two devices is the firmware version:

  4.4 (3.42) on my device and 4.5 (1.45) on devices where "Trunk of use" is available.

  Q1: Should I upgrade or there is workaround to use sip trunk without this option?

  Q2: Do I have to pay for this update?

  Q3: If my distributor can not get it to me or my relationships with them stopped can get updates directly from cisco?

  See the section "Deployment of a Unified CM MCU as a multimedia resource" in the installation guide that matches your version of software MCU.

  MCU 4.4 Installation Guide

  MCU 4.5 installation guide

  Upgrades of software MCU does not require a key to unblocking, but a contract of active service for the MCU is required to download the software.

  Series 5300 MCU software

• a way to move c90 to 5320 mcu Conference

  I have a setup where we use the multi-site c90 option. Is it possible to move a video conference live from c90 to 5320 mcu. The reason is that there may be a 5 attending the video conference and c90 can handle 4 (3 + himself). I don't know if one needs for 5 participants before the video conference begins and I have no port on the 5320 MCU to run all the video conference with this

  Does anyone know a solution to this?

  Best regards

  Jesper

  Check:

  http://www.Cisco.com/en/us/docs/Telepresence/endpoint/codec-c-series/TC6/api_reference_guide/codec-C90-API-reference-guide-tc62.PDF

  
  xCommand Call UnattendedTransfer
  Transfers an ongoing call to another participant. The CallID is returned when the xCommand Dial command is run. During the call you can run the xStatus Call command to see the CallId. Fully supported for SIP calls only.
  Requires user role: USER
  Parameters:
  CallId(r): <0..65534> Number(r):
  Example:
  xCommand Call UnattendedTransfer CallId: 2 Number: [email protected]/* */ com
  *r TransferUriResult (status=OK): ** end
  

• 5320 MCU in TMS - booking Conference

  I have a new 5320 MCU configured and managed in the TMS.  I can create a conference directly on the MCU, add participants, and it will dial a number and join the participants to the call correctly.  However, if I try to book a conference at TMS by selecting the participants and resource MCU, MCU does not connect endpoints for the call.  If I look at the details of calls that it said shows the following.  It's like he is waiting for the client to call the bridge, not the MCU outbound calls to customers?

  Participants will connect using this route:

  Customer MOVI ==> Bridge

  Hi if it is customer movi you attempt to dial, you must assign the automatic Conference connect and then add outgoing call participants where you type the movi/jabber address manually. You can see the connection setting tab before saving the Conference to see how the call will be set up (if the mcu expectd the customer allowing to switch or the mcu dial out). Customer MOVI has not automatically as regular endpoints generally have for the SCM cannot guarantee the call will implement.

  /Magnus

  Sent by Cisco Support technique iPhone App

• 5320 MCU software update 3.1 TS

  We currently have 5320 MCU running version 4.5 (1.45). I see that Cisco offers code TelePresence MCU server:

  http://www.Cisco.com/c/en/us/support/conferencing/Telepresence-MCU-5320/model.html#releasenotes ~ rdtab1

  Looking at the release notes is not very clear if when running 3.1 GST in MCU we will lose the ability to "Téléprésence MCU" in CUCM to use this 5320 MCU for Ad - hoc conferences.

  I know that GST 3.1 does not offer this possibility, but if you look at the file name for the MCU is cisco_ts_3.1_1.98_for_mcu_5300.zip (32,04 MB) vs GST 3.1 cisco_ts8700_3.1_1.98.zip (26,24 MB)

  Thank you

  If you upgrade your 5320 MCU with the telepresence server migration software, it will transform the MCU in a server of telepresence for all functions and features will be a telepresence server and not a MCU.  See the Software of TS running on MCU 5300 Series installation guide on how to convert your MCU to a telepresence server, if you are interested.

  Here are two good discussions comparing platforms MCU and telepresence server, one of them specifically on migration from one to the other.

  What-difference-between-MCU-Cisco-Telepresence-Server

  Why-Replace-MSE-8510-MCU-44-Telepresence-Server-31

  The cisco_ts_3.1_1.98_for_mcu_5300 software is for a series of 5300 MCU migrating to a server of telepresence.  The cisco_ts8700_3.1_1.98 software is specifically for the hardware already running a TP server software, such as the various servers of telepresence models listed here, this includes MCUs migrated to the server TP as the 5300 MCU to MCU MSE 8510 series software.

• How to select when several shapes overlap in the page layout view

  When changing the opinion of EM structure layout, it is common to have several forms and/or port objects overlap in the same place. How to choose the object you want in this case?

  In general in any layout view, when you select objects that overlap, the smaller form will be selected by default.  Hold down the Ctrl + Shift, and then to the same place to scroll through all the objects that are under the mouse.

• Cisco 5300 MCU failed to register with the SIP registrar

  I have a new Cisco 5300 MCU I have just begain configuration initially.  Under settings, SIP, it says registered.  However, to the title of the Conference, I have set up, it is said the recording failed.  If I click on failure, under the statistical heading he says SIP Registrar ID, could not be saved. No reason? Thank you.

  You made sure check the box 'Allow digital ID Registration for conferences' on the settings > page on the MCU SIP?

  If Yes, did you effectively ensure the digital 'ID' field with a numeric for the Conference in question when trying to SIP register for the Conference?

• Allowing endpoints make multi-point on Cisco 4505 MCU calls

  Hello

  I have a Cisco 4505 MCU and several endpoints.  Is there a way to allow that my end point called multipoint adhoc using MCU 4505?  For example, I would say that dial site1 using mcu, then dial site2 help mcu or call a group (site 1 and site1...) using mcu and it would know that it is supposed to use the 4505.

  Thank you

  Ravi

  Of course, you can configure (a few 100) static, meeting rooms, auto create conferences on the fly, based on a model or have the means put in place and there is even an on screen menu allows users to create or join conferences.

  Check out the example (page 37ff) Administrator's guide

  http://www.Cisco.com/en/us/docs/Telepresence/infrastructure/MCU/admin_guide/Cisco_TelePresence_MCU_4-4_Product_administration_guide.PDF

• Cisco Telepresence 5320 MCU

  Hello..

  We have integrated Cisco MCU 5320 CUCM Version 10.x and we are able to make calls to endpoints registered CUCM (SX20) to MCU with the ID of the meeting in addition to this, we use also VCS-control and have endpoints registered Polycom on to him but we are not able to make calls to MCUS using endpoints of Polycom recorded on VCS - C.

  Please suggest a guide too which can support on the rules of numbering as well.

  Rgds,

  Vika

  I am not able to give a precise any comparison between the differences of a MCU which is on CUCM or VCS, as I do not have a background in call manager.

  What is the problem you are having with TMS scheduling?  Can you elaborate and explain that you have problems with, I can try to help.

• Cisco 4205 MCU and 5320 waterfall or any other alternative?

  There are 2 ports of microcontrollers 5320 (4.5) and (4.4) 4205 offering documents multimedia 16 and 12. I need to work together as an mcu with 28 or ports available max. Can anyone describe how can I do this?

  http://www.Cisco.com/c/en/us/support/docs/conferencing/Telepresence-MCU-...

  It's that this article may be the solution to my problem?

  Hello

  In your case use MCU 5320 (MCU1) as master and will act as a gateway for the 4205 MCU (MCU2) since no feature of the H323 gateway configuration and no guard integrated for series 5300 MCU.

  Kind regards

  ACE

• C90 w/4210/5320 MCU H.239 Frame Rate

  I admit the departure, it's "H.239 101" type question, but our environment is transitional on very old rooms of 4:3 which were never designed to manage content on separate screens so I'm just now my hands dirty with the intended user, experience sharing content.

  My question is around H.239 - cadence for C90 endpoints as well as MCU-4210/5320...on the surface, it seems that they are able to share plenty of movement, full-video cadence in the H.239 channel, right? must be able to handle 720 p, 30 frames per second?

  In tests, I connected a C90 to two MCU to the relatively high rate of calls (1.5 MB, 2,0 MB) and when I check stats, H.239 channel turns to the expected bitrate and resolution-but very low frequency of frames... between 4/7 frames per second

  I think I am missing some setting commonly or game setting between the endpoint and MCU.

  In addition to setting minimum outflow for the content on the MCU, what other effects H.239 - cadence? I tried to play with the settings of weight main/presentation in the C90, but does not appear to affect the results.

  Thanks in advance for any response

  Take a look at this discussion, cisco-mse-8510-content-frame-rate-and-resolution-limitations.  In short, the cadence of the content that is being received and sent by the MCU are dependent on how you have the quality that is configured for the endpoint PC Input, that is to say: (default) sharpness or movement.  There is no middle ground, or dynamic parameters, it's one of those two.

• Cisco TelePresence MCU disconnects a session IP

  Now I have a MCU 4220, two VCS (neighbouring) and a version endpoint MXP 95. MCU is 4.3, and the version of VCS is X5.2.MCU are recorded in a vcs and 95 MXP is recorded in other vcs. Two VCS are nearby. Now MCU makes a call with MXP 95, but after a minute or so, MCU drops the call. I tried several times, and the situation is the same. The message to MCU I founded is "h.245 network connection error". I checked the network, everything is OK. I took an another MCU 4505 to test. Nothing wrong happene and the call can work well.

  Please give me some advice.

  Thank you.

  Hi do you have a firewall on your network where traffic can be? See you on your video mxp for this minute?

  / Magnus

  Sent by Cisco Support technique iPhone App

• 5320 MCU and EX60

  Hello

  I was wondering if you could register EX60 directly to the MCU5320

  I can't find any documentation on how to do it properly

  i'm train to try to register as SIP in vain

  any help will be greatly appreciated

  Thank you

  Unlike the previous TANDBERG MCUs, none of the newer Cisco microcontrollers including the 5300 series is not an inner gatekeeper or clerk.  You will need to either save it to a CUCM or VCS call control server.

• Width of the desktop in the fluid layout view

  Hi people, I am at the beginning of a new design of the site and have a problem with my site Office being too broad, which all fake gif articled. http://primerestaurant.co.nz/new/index

  In my CSS I have this code:

  *

  Properties Grid Dreamweaver fluid

  ----------------------------------

  DW-num-CLO-mobile: 5;

  DW-num-CLO-Tablet: 8;

  DW-num-OCOL-Office: 8;

  DW-gutter-percentage: 25;

  and also

  / * Desktop layout: 769px for a max of 950px.  Inherits the styles of: Mobile and tablet. */

  And yet, the desktop version of the site continues to sit on 1266 broad. Is there somewhere else I need to make changes to the site Office does not exceed 950?

  Of course, you can have a better suggestion for how can I place an image on the template page. the customer likes the existing animation on the current site http://primerestaurant.co.nz

  Thanks in advance for the advice,

  JO

  BoppyW wrote:

  Thanks Ben, but unfortunately the Bootstrap is beyond my budget.

  Bootstrap is free. And This is without the extension, also free.