MD3220i + 5524 switches

Similar Questions

• ENABLE SNMP POWERCONNECT 5524

  Hello,
  I have a problem on one of my Dell PowerConnect 5524 switches .
  I do not turn on SNMP.
  All my other switches work well except this one .
  I looked extensively without results
  

  SW-STUDIOshow snmp

  SNMP is disabled.

  Community community-access view name string IP mask
  -------------------- ------------------ -------------- ------------ ------------
  Public ReadOnly default all the

  Group Community-String name IP address mask type
  ------------------ ------------ ------------------- ------------------- ------

  Traps are enabled.
  The authentication failure trap is enabled.

  Notifications of the version 1, 2
  Udp target address community Type to the attempts of Version filter
  Name of the dry port
  ---------------- -------- ----------- ---------- ----- ------- ----- ---------

  Notifications of version 3
  Udp security target address Type attempts username filter
  Name of the dry Port level
  ---------------- -------- ----------- -------- ----- ------- ----- ---------

  Contact system:
  System location:

  Hello, my problem is ok.

  It was enough just to spend the following command: Server snmp Server

  Quick glance:

  SW-STUDIO # configuration

  SW-Studio (config) # Server snmp Server

  Exit SW-Studio (config) #.

  SW-STUDIO # display snmp

  SNMP is enabled.

• Linking to 5524 battery battery N2024

  Dell Powerconnect 5524 can be stacked by HDMI and the newer N2024 models can be stacked by dell's exclusive stacking ports. Is it possible to connect these two fireplaces? You can connect through FPS? You can connect them through an OFFSET? What is the best process here?

  The 55xx and the N2xxx can be stacked together, except that you can treat both batteries similar to as if they were just a simple switch. Stacking basically makes only one switch, so you'd plug it comes in the same ways that you would connect a single 55xx with a single N2xxx.  If you use a LAG, however, should be split across several members of the battery cable connections.  Thus, for example, if you have a stack with three members and you have a LAG with two cables, use a port to two permanent members so that your GAL covers at least two members.  For the two chimneys creates a network more resistant, so if a member falls down the link will stay up.  In other words, if you use two ports on the same Member of the stack and Member goes down, then you have lost the connection, so it is best to divide the LAG on several members of the battery.

  I hope this helps.

  B

• Locking options down PowerConnect 5524 after analysis of vulnerabilities

  Hello

  After a recent vulnerability scan with BeyondTrust Retina, our PC 5524 hits showed as:

  Medium	10890	Web resources/cgi-bin / detected
  Medium	10898	Web resources detected /cgi-bin/index.jsp::$DATA
  Medium	10907	Web resources detected /cgi-bin/jsp/index.jsp::$DATA
  Medium	10930	Resource Web/demo /... /%3F.jsp detected
  Medium	10942	Resource Web/demo /... /index.jsp: $Data detected
  Medium	10953	Resource Web/demo /... /jsp/index.jsp::$Data detected
  Medium	10871	/Index.jsp: $DATA detected Web resources
  Medium	10885	Web resources detected /jsp/index.jsp::$DATA
  Medium	10910	Web resources detected /scripts/%3f.jsp
  Medium	10919	Web resources detected /scripts/index.jsp::$DATA
  Medium	10926	Web resources detected /scripts/jsp/index.jsp::$DATA

  Not to mention that the disabling of the web interface, is possible to block access to these directories?

  Thank you.

  I'm not aware so as to lock the access to these directories. Have you tried to disable HTTP and HTTPS enabling? Then, run the same scan and see if the result is the same.

  You could try a firmware update. There are a few security enhancements in the latest firmware.

  http://Dell.to/1KG1TZe

  If it is a must to disable the web interface, the switch that can be fully managed through the CLI.

• Stacking question: can I combine a stack of 5548 with a stack of 5524?

  Can I combine a set of four switches PowerConnect 5548 with a stack of two switches PowerConnect 5524? I don't know to ensure they are running the same firmware, but I didn't not see the documentation on the size of maximum stack or between models stacking limits.

  Thank you.

  Yes, you can stack 6 switches together, any 5500 stack with any other, to a maximum of 8

• Request support by MD3220i - error cluster [CF]

  Buon giorno, US vs riscontro gentile e di assistenza in merito al evento following preventivo:

  The infrastruttura e nostra composed da UN MD3220i con 3 host due e R610 PowerConnect 2848 switch, da some giorno a perdere instradamento verso gli hanno begun the host Announces where the MD3220i.

  Da una prima disgnostica di message following sulla MD abbiamo rilevato it 'alert ':

  Date/time: 08/01/16 8.26.31
  Sequence number: 41599
  Type of event: 4011
  Event category: error
  Priority: critical
  Description: Virtual disk not a being preferred due to the AVT/RDAC failover
  Specific event codes: 0/0/0
  Component type: RAID Controller Module
  Location of components: enclosure 0, Slot 1
  Recorded by: Module to slot 1 RAID controller

  Raw data:
  4 d 45 a2 7f 48 03 00 00 00 00 00 00 00 00 00 4 c
  11 40 18 01 97 eb 57 00 00 00 00 00 00 00 00-9F
  00 00 00 00 01 00 00 00 22 00 00 00 22 00 00 00
  08 00 00 00 00 00 00 00 02 00 00 00 01 00 00 00
  0 a 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
  01 00 00 00 00 00 01 00 00 00 00 00

  We have tried a curare infrastruttura MD, host switch e spegnere.

  After the riaccensione he message di "alert" su e scomparso totally, senza più particular if MD, recoupling outdo degli host verso MD3220i risultava Semper ad where con conseguente perdita accesso alle cartelle di rete e macchine virtuali.

  Host No. 2 dei R610 abbiamo quindi con spento 3 he risultato che dopo d manuale da console del servizio cluster it sistema e partito a funzionare senza problemi di comunicazione più correctly.

  Lato host abbiamo rilevato che some door ISCSI MD non sono più ragiugibili del (nello specifico n ° 1 of the castroni sono no door porta del MD3220i controller)

  The VLAN non sono state modificate e lato PowerConnect 2848 switch if not rilevano if.

  Current location: MD3220I senza if a host adapter solo di n ° 3 access.

  Company di MD3220i:

  He prodotto e stato nel 2010 labor-intensive, co del prodotto e scaduta it 13/12/2015.

  Re: MD3220i fuori co serial number F1QGY4J

  Buongiorno, the sto contattando by mail.

• Reference Dell powerconnect 5524 cannot ping between coelio and trunk port

  Hello...

  We set up a new switch of 5524 I untagged on vlan 20 and access ports where vlan 20 I allowed. I created a computer on the access port on the same trunk port ip net... cant ping beween them. I'm no expert of switch, so I wonder what I missed. I did the same thing on a dell old 3524 and it works directly...

  Here's the port config I tried to do a ping beween is 6 and 10 ports

  (Another thing, how how to remove):

  switchport mode trunk
  switchport access vlan none)

  Any help would be greatly appreciated!

  interface vlan 1
  IP 88.131.90.252 255.255.255.240
  !
  interface vlan 5
  the name 'SCE CJA'
  !
  interface vlan 6
  the name "out of Tele2.
  !
  interface vlan 7
  name "Outside Telenor"
  !
  interface vlan 8
  name "TDC Multivrf"
  !
  interface vlan 20
  TDC-CISCO-LAN name
  !
  [0mMore: , quit: q or CTRL + Z, one line: interface vlan 21]
  the name "FW inside."
  !
  interface vlan 99
  name «FW sync»
  !
  gigabitethernet1/0/1 interface
  Description CPE1
  switchport access vlan 5
  !
  interface gigabitethernet1/0/2
  Description CPE2
  switchport access vlan 5
  !
  interface gigabitethernet1/0/3
  Df description
  spanning tree portfast
  switchport mode trunk
  switchport access vlan no
  !
  interface gigabitethernet1/0/4
  Description Oupps-cb2
  [0mMore: , quit: q or CTRL + Z, a single line: spanning tree portfast]
  switchport mode trunk
  switchport access vlan no
  !
  interface gigabitethernet1/0/5
  Upp-ccm1 description
  spanning tree portfast
  switchport access vlan 20
  !
  interface gigabitethernet1/0/6
  Oupps-ccm2 description
  spanning tree portfast
  switchport access vlan 20
  !
  interface gigabitethernet1/0/7
  Tdc-multivrf1 description
  switchport access vlan 8
  !
  interface gigabitethernet1/0/8
  TDC-multivrf2 description
  switchport access vlan 8
  !
  [0mMore: , quit: q or CTRL + Z, one line: interface gigabitethernet1/0/9]
  Description Oupps-cb-tq03
  spanning tree portfast
  switchport mode trunk
  !
  interface gigabitethernet1/0/10
  Description Oupps-cb-tq04
  spanning tree portfast
  switchport mode trunk
  !
  interface gigabitethernet1/0/11
  Tele2-outside description
  switchport access vlan 6
  !
  interface gigabitethernet1/0/12
  Tele2-outside description
  switchport access vlan 6
  !
  interface gigabitethernet1/0/13
  Telenor-outside description
  switchport access vlan 7
  !
  [0mMore: , quit: q or CTRL + Z, one line: interface gigabitethernet1/0/14]
  Telenor-outside description
  switchport access vlan 7
  !
  interface gigabitethernet1/0/15
  Description Word-Oupps-fw-tq01-inside
  switchport mode trunk
  !
  interface gigabitethernet1/0/16
  Description Word-Oupps-fw-tq02-inside
  switchport mode trunk
  !
  interface gigabitethernet1/0/17
  FW-sync description
  switchport access vlan 99
  !
  interface gigabitethernet1/0/18
  FW-sync description
  switchport access vlan 99
  !
  interface gigabitethernet1/0/19
  Description Word-Oupps-fw-tq01-outside
  [0mMore: , quit: q or CTRL + Z, a single line: switchport mode trunk]
  !
  interface gigabitethernet1/0/20
  Description Word-Oupps-fw-tq02-outside
  switchport mode trunk
  !
  interface gigabitethernet1/0/22
  FW-Sync description
  switchport access vlan 99
  !
  interface gigabitethernet1/0/23
  Description Word-Oupps-FW-tq01-outside
  192.168.11.1 IP address 255.255.255.0
  switchport mode trunk
  !
  interface gigabitethernet1/0/24
  Description Word-AIN-LAN-SW
  switchport access vlan 20
  !
  IP route 0.0.0.0 0.0.0.0 88.131.90.241

  [0mMore: , quit: q or CTRL + Z, a single line:]

  Information of VLAN

  The name of the VLAN Tag Ports Ports unmarked Type permission
  ---- ------------ ------------------ ------------------ --------- -------------
  1 1 article gi1/0/3-4, default required
  Article gi1/0/9-10
  item in gi1/0/15-16,
  item in gi1/0/19-21,
  item in gi1/0/23,
  item in gi1/0/25-48,
  TE1/0/1-2.
  GI2/0/1-48.
  TE2/0/1-2.
  IG3/0/1-48.
  TE3/0/1-2.
  IG4/0/1-48.
  TE4/0/1-2.
  IG5/0/1-48.
  TE5/0/1-2.
  GI6/0/1-48.
  TE6/0/1-2.
  gi7/0/1-48.
  TE7/0/1-2.
  gi8/0/1-48.
  TE8/0/1-2, m 1-32
  5 CPE TDC article gi1/0/3-4, item in gi1/0/1-2 permanent required
  [0mMore: , quit: q or CTRL + Z, one line: article gi1/0/9-10]
  item in gi1/0/15-16,
  item in gi1/0/19-20,
  item in gi1/0/23
  6 outside section gi1/0/3-4, item in gi1/0/11-12 permanent required
  Tele2 item in gi1/0/9-10,
  item in gi1/0/15-16,
  item in gi1/0/19-20,
  item in gi1/0/23
  7 outside article gi1/0/3-4, item in gi1/0/13-14 required permanent
  Telenor item in gi1/0/9-10,
  item in gi1/0/15-16,
  item in gi1/0/19-20,
  item in gi1/0/23
  8 TDC Multivrf item in gi1/0/3-4, item in gi1/0/7-8 permanent required
  Article gi1/0/9-10
  item in gi1/0/15-16,
  item in gi1/0/19-20,
  item in gi1/0/23
  TDC-CISCO-LA 20, article gi1/0/3-4, item in gi1/0/5-6, item in gi1/0/24 required permanent
  N item in gi1/0/9-10,
  item in gi1/0/15-16,
  [0mMore: , quit: q or CTRL + Z, one line: item in gi1/0/19-20,]
  item in gi1/0/23

  In safe mode the PVID is 1 VLAN by default. You can do this by entering the command #switchport trunk vlan native {number of vlan}. If Cisco is configured to accept and send the marked packets and has an IP address in the subnet of VLAN 20, it should be able to communicate with other devices in VLAN 20.

• MD3220i meet incl. servers. Hyper-V system

  I am trying to connect to a San:

  • Two Dell Powervault MD3220i drive bays
  • Two gigabit ethernet Cisco switches
  • Three (will be 5 in a few months) PowerEdge R710 Hyper - V hosts Win2012R2

  I am aware of technical guides, deployment guides, etc. But all I can find is an address for the drive bays scheme. I searched these forums for questions simular, but mostly they are on the configuration of the controllers and the iscsi ports, but not on servers.

  I connected the disk controllers array with the management by Bay (1 per controller) ports to the LAN switch (vlan management). The eight by Bay (4 per controller) iscsi ports are connected to the dedicated SAN switches. Half the first SAN-switch ports. Other ports to the second SAN-switch.

  But I can't get the idea on how to connect the Hyper-V hosts. The Hyper-V hosts are in this exact similar PER710 time servers 3. There will be 2 more in a few months. For this purpose, I chose for a wiring diagram with switches and not directly related to the drive bays.

  My Hyper-V hosts all have two dedicated network cards (not bundled, jumbo frames, multipath) for ISCSI traffic. What will be the perfect for this configuration addressing scheme?

  I read on different subnets to the iscsi disk array ports. Allows to call their subnet A, B, C, D. And there's a different subnet for the management ports, connected to the vlan management on my LAN switches. Lets call this subnet E.

  In what subnet I put my Hyper-V hosts iscsi ports?

  I start with 8 total cards in each server and if you can afford it, consider even 10 NICs (NETWORK ports).

  Use a configuration like this:

  -2 ports in a team for the management of hosts

  -2 ports in a team for VM-to-LAN traffic

  -2 ports in a team to pace heart/CSV/Live Migration traffic

  -4 ports non - teamed up for iSCSI with 4 unique subnets

  If you limit to 8 ports on your server, you can restrict the host management to just 1 port and also limit the traffic of Migration of the heart/CSV/Live rhythm 1 port.

  On an extreme budget, you can use 1 for the management of hosts and VM-to-LAN traffic and then 1 port for heart rate, but I would reduce iSCSI 2-port before making this option for only 6 ports.

  When grouping, it is better to use 2 or more ports from the same provider NIC (Intel or Broadcom), even if opting for Windows native grouping.

• Ping on MD3220i error

  Hello

  I'm trying to set up a unit of SAN MD3220i.

  I use IP addresses by default for each port iSCSI on controller 0 and 1 controller.

  I installed my host (Hyper-V Server 2008 R2) and I use 2 network cards for SAN traffic on this host, the IP addresses that I've assigned are 192.168.130.3 (255.255.254.0) and 192.168.132.3 (255.255.254.0)

  Each NETWORK adapter is connected via a separate to the San switch.

  When I ping to each of the 4 SAN ip addresses, only 2 answer, these are 192.168.130.101 and 192.168.132.101.

  Why the other two IPS (192.168.131.101 and 192.168.133.101) without responding to the ping request.

  All on the ports of SAN subnet masks are 255.255.255.0

  Thanks for your help

  Hi Sam,

  Sorry for the delay, I've tried a few things and was able to solve the problem.

  The SAN comes with default subnet masks 255.255.255.0 on all iSCSI ports, but I put my NIC host having 255.255.254.0 subnet masks.

  Once I changed to 255.255.254.0 SAN subnet masks I could ping all of the 4 ports on the host channel.

  Thanks a lot for helping me with this problem.

• IP MD3220i address scheme with esxi4.1

  I have a Setup running for awhile. (2 R815 welcomes with 8 iscsi NIC and md3220i with two controllers) I was adding another host and a second iscsi switch which was then looking around to see if the guidelines have changed. In my setup, I have 8 NIC per host. I thought 4 paths to each controller. Is this an overdose? I noticed the leaves dell mentions 4 NICS per host, which would give 2 parallel tracks for each controller.

  Current config:

  Host 1:

  10.10.6.211

  10.10.6.212

  10.10.7.211

  10.10.7.212

  *

  *

  10.10.9.212

  MD3220i

  RC0-1: 10.10.6.101 (Controller raid 0, port 1)

  RC0-2: 10.10.7.101

  RC0-3: 10.10.8.101

  RC0-4: 10.10.9.101

  RC1-1: 10.10.6.201

  RC1-2: 10.10.7.201

  RC1-3: 10.10.8.201

  RC1-4: 10.10.9.201

  Host 2:

  10.10.6.213

  10.10.6.214

  10.10.7.213

  10.10.7.214

  *

  *

  10.10.9.214

  Currently, there is only 1 switch iscsi (bad idea). I'll add a second week next for redundancy. Directions on how can I separate the wiring port-based?

  Can I change my intellectual property regime?

  Now when I turn on repeat alternating on my esxi, I see 4 paths with Active (e/s) for each logical unit number.

  Thank you!

  Note: I have posted this on a different thread, and does not have all the answers. I guess that's maybe because the thread has been answered.

  Hello Nid15,

  Yes you are right you will get 4 GB less than fresh General.

  Please let us know if you have any other questions.

• The PowerConnect 5524 ARP Cache size

  Does anyone know powerconnect 5524 size of the ARP cache? I used the command: "show arp" to the PowerConnect 6248 switch, I got information: cache size is 1024. I can't got the PowerConnect 5524 information. Thank you. Core-6248 #show arp age time (seconds)... Response time of 1200 (seconds)... 1 Retries........................................ Cache size to 4... 1024 Dynamics renew Mode... Disable the account Total entry / pic... 796 / 820 static entry configured Count / Active / Max... 0 / 0 / 64 5524-3F # display the status of address arp HW IP address of the Interface VLAN - vlan 1 dynamic gi1/0/11 10.xx.xx.xx xx article

  Hello

  The size of the arp cache is 1024, identical to the 6200 series.

• Buzz of noise in the tempo switch

  My song has 4 different tempos. Every time that happens, occurs a humming noise. If I get all tracks FX behind it disappears. How can I keep the delay, but not the buzz?

  Thank you y´all.

  Use automation for on/off switch of the delays to and after each change of tempo.

  If that kills too late in the face of that time, and then introduce a Gain ahead of every delay, automate the Gain to cut admission to the delay when changing the tempo. Who will cut the whole track, however.

• Switch between keyboard languages 3 (or more)

  I have three languages: language A, language B, C language

  I'm on A language and to switch to the C language.

  Heat the shortcut keyboard CMD + space twice to change the language. It's change of a language.

  I have heat twice again and it works properly.

  How to disable this smart switching algorithm?

  You really tell us that what you see in the menu 'flag' on the top right of the screen does not always match what is typing at the keyboard?

• Can I switch to OSX 10.9.5 directly to Sierra.

  Can I switch to Sierra de OSX 10.9.5 no other updates between the two?  I have an iMac mid-2011.

  Yes.

  (145115)

• on/off switch does not work since the SIERRA

  Hello

  Since I'm sierra os that the on/off switch does not show me the dialogue window in which you can choose between power, reset, disconnect you.

  This is a problem of Sierra? There is an option in the system Pref?

  Thank you

  It works very well in the Sierra.  Simply press the button longer.