Memory of blowing?

Similar Questions

• Series of 4 beeps continuously at startup

  As soon as I turn on my 530 Inspiron from Dell with Windows Vista Home Edition s, have at all times a series of 4 beeps.  The CD sounds like it is running, but nothing appears on the monitor.  I tried to find out what to do about the area of troubleshooting the Dell website, but it didn't follow one of the beep codes listed.  One speaks also of switches, but I don't know how to find out what kind of switch I.  The green light at the back is on all the time, and I couldn't find A fires, B, C and D on the back.  Any help that could be given would be greatly appreciated.  Thank you.

  I had the same problem and was able to fix it with the following steps:

  1. Unplug everything
  2. Unscrew and remove the side panel
  3. Pop-out each memory card, blow on them and pop that hide them in (make sure that the legs down lock)

  One of the memory cards must have shaken lose somehow, even if they seemed fine at first.  My system began immediately to the right upwards later.

  All the best,

  David

• Satellite A60 memory upgrade does not help

  Hi, I have a Satellite A60-793 and I want to upgrade the memory by adding a 512 MB of memory currently installed.

  I tried to install a 512 MB DDR PC2700 333 MHz SODIMM module, but the system does not boot to the top: it emits a long whistle blow and then stops automatically. If I remove the module, the system starts properly.

  I have already updated my BIOS, I here something more, I can do to make it work?

  You simply used bad, faulty or not fully considered supported modules.

  Recommend to test it with another new

• Satellite A60-217 memory upgrade

  Hi, I have a Satellite A60-217 (Intel Pentium IV HT 532, 3.06 GHz), and I want to upgrade the memory by adding a 512 MB of currently installed memory (256 MB with 64 MB shared memory for video card).

  I tried to install a S3 + PC2700 DDR SODIMM 512 MB module, but the system does not boot to the top: it emits a long whistle blow and then stops automatically. If I remove the module, the system starts properly.

  The manual indicates the speed of the memory supported is only PC2100. Is this true? The module is maybe defective?

  Thank you

  Hello Stefano

  Of course, the added module is not compatible and makes trouble. I found the info, this compatible module PC2700 512 MB (PA3312U - 1 M 51).

  Google a bit and you will find lots of information on the module with the PA3312U - 1 M 51 part number.

  Good bye

• Pavilion dv6 Notebook PC: I can pass on my HP Pavilion dv6 Notebook PC (memory, processor, graphics)

  My dv6 became very slow. I am running Windows 10 and now it takes 15-20 minutes to wake him up from his sleep and connect. Ive done a lot of cleanup and optimization, but nothing got better on that. It get very hot very quickly and the fan always seems to be at the top. I'm looking to try to upgrade the memory and perhaps the (quad-core) processor at least if possible, to see if the performance is going to do better. I can hardly do anything on this issue now because it takes too long! I have a 1 TB of HDD installed there a few years and who works well, but everyday navigation, products microsoft office and editing photo/video light from time to time are almost impossible! What memory and processors are compatible with my device that I could look in the upgrade? Any help is greatly appreciated! I'm new to upgrades of memory and others so I had a bit of a problem of the research/understand exactly what I would like to search! I will post the form below!

  Thank you!

  Data sheet:

  Name of the OS	Microsoft Windows 10 Pro
  
  Version	10.0.10586 build 10586

  System manufacturer	Hewlett-Packard
  
  System model	HP Pavilion dv6 Notebook PC
  
  Type of system	PC x 64
  
  System SKU	XG740UA #ABA
  
  Processor	Intel (r) Core i3 CPU       M 370  @ 2.40 GHz, 2 Lossnay, 2399 Mhz, 4 logical processors
  
  Version of the BIOS/Date	Hewlett - Packard F.29, 07/11/2011
  
  SMBIOS Version	2.6
  
  Embedded Controller Version	101.56
  
  BIOS mode	Legacy	

  Physical memory (RAM) installed	4.00 GB
  
  Total physical memory	GB 3.80
  
  Available physical memory	716 MB
  
  Total virtual memory	7.67 GB
  
  Available virtual memory	1.26 GB
  
  Page file space	3.86 GB	

  You have a model dv6-3155dx. Here are your specs:

  http://h20564.www2.HP.com/hpsc/doc/public/display?docid=emr_na-c02548013

  Here is the Service Manual:

  Manual

  See p. 23. Your laptop has the CPU i3 - 370 M and UMA (Intel HD) video so, unfortunately, the processor is not extensible because it is soldered to the motherboard. Put video updated would also require the replacement of the motherboard. CPU upgrades are very difficult and rarely justify financially, in any case, but in your case is not possible at all unless you replace the motherboard, which is even more expensive and less be justified financially. The cost of high end motherboard and CPU and work, you might as well buy a new laptop.

  But all is not lost. The best upgrade, you can do is to install an SSD. You can also switch to 8 GB of RAM. An upgrade will be useful, together, they would be a game-changer.

  You would need 2 x 4 GB modules specified thus:

  Memory module (DDR3 PC3 - 10600 1333 MHz) - 4096 MB 599092-001

  https://www.Amazon.com/HP-VH641AT-4-GB-DDR3-PC3-10600/DP/B0030L3B8E/ref=sr_1_1?ie=UTF8 & qid = 1472066313 & SR = 8-1 & Keywords = 599092-001

  This model is very, very picky about the memory and it must have 8 black blocks on the side, not 4. Also very intolerant of memory not specified in general. Remember that I bound will work. 'How to' on the manual p.60.

  SSDS are a little harder to choose (as many options) and what I need to know is your budget. I recommend at least a concert 500 class SSD and which will cost $120-160. Since you have 10 Windows, it would be easy to download the Microsoft recovery media directly and simply reinstall, then find the drivers and applications and migrate the data. The installation will be ignited automatically the first time that the computer is connected to the internet. You can also clone the existing content of the new SSD hard drive, but I do not recommend with a facility that is malfunctioning.

  We also probably discuss blowing dust and verification of thermal management in general. A laptop that suddenly becomes very slow, as you describe may have a hard drive problem, too. You need to run diagnostics on the hard drive and also just to check to see if it is full. Drops of performance as a rock if the hard disk reaches 90 percent and more capacity.

  Let us know if you have any other questions.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• Late 2009 iMac Memory Card Slot Gone Bad?

  My memory card seems to have stopped working. Is there a way I can tell if it's the memory real slot hardware vs whether software or my SD card.

  I have reset PRAM and SMC. I had to reset the PRAM periodically to retrieve my startup chimes. I was wondering if they can be connected.

  I did first aid utility disk on the map and it seems to be OK, for what is disk utility is.

  It started with my card being ejected unexpectedly. If I reinsert the card, the card is not recognized.  This would solve usually solve the problem until the next time.

  Any help appreciated.

  First thing to do is clean

  a thin long brush, blower, vacuum.

• LabView VB6 Dll interface causes memory leak

  Hello

  We use a large written in vb6 in our laboratory measurement built house software. Recently, we have added a new detector that is read using a labview vi that is called using a dll directly from vb6. Here, we call the function for example of read_detector which starts the collection of data and in a next step writes the data to a string. When you have finished the called function returns a pointer to the string and its length. VB6, we read this pointer and process data.

  This is a memory leak. This could be the case because we presets not memory for labview to write in and so just writing lab data in memory without releasing again? In the current configuration, the function of the dll is just called again and again and each lab view creates a variable outputstring.

  If we allocate the memory. How can we achieve for vb6?

  Best,

  Julian

  Well first of all, a handful of string LabVIEW is a very specific type of data LabVIEW. Not only is only LabVIEW himself knows exactly how to allocate and deallocate, but you must also allocate and deallocate in exactly the same instance of LabVIEW. Given that your LabVIEW DLL is executed for this purpose inside the DLL to run LabVIEW, you must also recover the LabVIEW memory manager functions according to DSDisposeHandle() of the lvrt.dll and call it after you are finished with the strings returned by the DLL function. This is however made very complicated since there are circumstances where not lvrt.dll is actually used by your DLL but another LabVIEW runtime system. And if you happen to have two DLLs created with different versions of LabVIEW LabVIEW, each of them will load and use its enforcement LabVIEW system according to DLL load next. Believe me, you don't want to know how next dll works and how to make this opportunity to work in an application. This is the way for Microsoft to create a monster to manage the hell of the DLL and in this way, rather to create exponential version of hell.

  You create just two memory leaks for each call of DLL function at the moment. LabVIEW creates a new handle of string for each of the parameters string at each call, you dereference the pointer, and then copy the contents into a SysString. But you let the chain handles LabVIEW blow created around the stack and the next your function call, you initialize the new variables of the battery which is initialized to null and LabVIEW creates two new handles. Also you need to do is to define an "Integer DSDisposeHandle(LStrHandle As Long)" exported lvrt.dll function and call it once you have copied the data of the handle in your SysString for both of these handles.

  But basically calling a DLL LabVIEW from no LabVIEW code and using LabVIEW handles string or array as parameters is several times more trouble that it's worth. The easiest would be fair, allocate a large enough buffer beforehand and pass those to the Configuration of the service DLL LabVIEW function to not accept a handful of string LabVIEW but a pointer to a string C instead. Do you work around the problem on the memory allocated by someone else to worry about your own program of VB and duty he properly release. The disadvantage of this approach is, that you should make sure that the memory allocated buffer is large enough for the maximum possible length that your DLL function may never return.

  But another approach might be to leave out LabVIEW total here and call the DAQmx APIs directly from VB.

• Wow Error 132 memory cannot be written... and so on

  I'll have wow Error 132 arrive about an hour after the start of the game world warcraft, the game crashes and the error 132. I went on the support site for games and have done everything they said to do to solve the problem, I even updated my drivers and installed a new graphics card and have installed more ram made sure to reset virtual memory but continues to have the error again and become very frustrated and ready to blow this older HP desk top. I also went on HP website to get the drivers right and made sure I had all my top desk needed on their part I tried everything I know to do except replace the computer.

  Hi Noel1969,

  ·         Who is the manufacturer of the graphics card?

  ·         What operating system is installed on the computer?

  This error is because your DDR memory is volatile. This can also occur if the BIOS settings are wrong. The especially voltage can be set to AUTO. It is very important that you set the correct voltage.

  Example: ddr2 6400 setting 1.8 volt.

  Change (CMOS) BIOS/complementary metal oxide semiconductor settings can cause serious problems that may prevent your computer from starting properly. Microsoft has not Microsoft cannot guarantee that these problems can be solved. Change the BIOS at your own risk.

  I suggest that you contact HP to change the BIOS on the computer

  Check the voltage on the computer.

  I suggest that you check the version of DirectX on your computer.

  If you have a Nvidia Geforce, then downgrade to 93.71 driver (they are older, but still work)

  Try the steps suggested by Arygos in the link below: http://forums.worldofwarcraft.com/thread.html?topicId=1272299964&sid=1

  Thank you, and in what concerns:
  Swathi B - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• BSOD (memory management) (irql not less or equal)

  So I get this BSOD randomly every time than in quite awhile.  Im hoping someone can read my minidump files and let me know what they see. They are here. https://drive.Google.com/file/d/0BySzGDXCLzrUbUc4Q3I5dlgwdFk/view?USP=sharing

  Hello

  All mindumps were essentially the same.

  Error checking 1A, {41790, fffffa8001f6d910, ffff, 0}

  Probably caused by: win32k.sys (win32k! SURFACE::bDeleteSurface + 3 c 8)

  Win32k.sys is a component of Windows which means than anything else he has led astray.

  1. check memory very carefully.

  2. check with Support MSI, their drivers and documentation online and ask in their forums
  on known problems. Updated BIOS, drivers of low level chipset and on-board major
  and drivers of separate devices (see methods of updating driver below).

  BiosVersion = V12.3
  BiosReleaseDate = 10/01/2013
  SystemManufacturer = MSI
  SystemProductName = MS-7680
  BaseBoardManufacturer = MSI
  BaseBoardProduct = H61M-E33 (B3)(MS-7680)
  BaseBoardVersion = 2.0

  Support MSI
  http://www.msi.com/index.php?func=service

  MSI - Downloads (drivers and BIOS)
  http://www.msi.com/index.php?func=downloadindex

  MSI - Forums
  http://Forum-en.msi.com/

  MSI - Service
  http://us.msi.com/index.php?func=service

  MSI - Live Update online
  http://www.msi.com/index.php?func=downloadindex

  MSI - Contacts - USA - North America value
  http://www.msi.com/index.php?func=HTML&name=aboutus

  3 use ALL other methods in the troubleshooters below if necessary.

  4 if necessary run the Driver Verifier to see if it can indicate a CAUSE (see Driver Verifier methods
  below).

  ======================+

  Resolution in Windows 7 stop errors (blue screen) - has a section for if you can or cannot start Windows.
  http://Windows.Microsoft.com/en-us/Windows7/resolving-stop-blue-screen-errors-in-Windows-7

  -------------------------------------------------------------

  BCCode: 1a 0x0000001a

  Remove ALL power and reinstall all the memory cards and cables (both ends where possible).
  in fact, remove and replace - don't do not just tight. Make sure that the vents are clear and that the
  the fans are working. Even if the temperature is OK assume no heat does not affect the video,.
  sound or other system functions that it these get hot. Try adding a small fan blowing in
  the vents as a test. (These are especially for a PC not a laptop.)

  Have you recently added any hardware? Have you updated any drivers just before this started? (Check control panel - updates of Windows to see if all drivers have been updated it there all the time it started) Main likely culprits are video driver, other great drivers, memory, and antivirus/antispyware/security products can be at fault and also lead questions.

  Use the troubleshooter below and refer to the following message to drivers and memory when
  you get these sections and then back to the resolution of the problems according to the needs.

  ==========================================================

  BCCode: 1a 0x0000001a

  BCCode: 1a 0x0000001a<-- read="" this="">
  http://www.faultwire.com/solutions-fatal_error/memory-management-0x0000001A-* 1041.html? order = votes

  Bug Check 0x1A: MEMORY_MANAGEMENT<-- read="" this="" link="" for="">
  http://msdn.Microsoft.com/en-us/library/ff557391 (v = VS. 85) .aspx

  -------------------------------------------------------------------------

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard event viewer
  Windows. TIP - Options - Advanced filter allows you to see a time rather
  of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during ' blue screen of the.
  death ' crashes and displays information about all accidents of a table.
  Free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged, in particular the video drivers drivers however
  There are other causes.

  You can do mode if necessary safe or the Vista DVD command prompt or
  Options recovery if your system is installed by the manufacturer.

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  You can try a system restore to a point before the problem started when one exists.

  How to do a system restore in Windows 7
  http://www.SevenForums.com/tutorials/700-system-restore.html

  -------------------------------------------------------------------------

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  How to analyze the entries in the log file generating the program Checker (SFC.exe) resources of Microsoft Windows in Windows Vista cbs.log (and Windows 7)
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
  keyboard and mouse, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista (also Windows 7) Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  How to stop Windows 7 automatically install drivers
  http://support.Microsoft.com/kb/2500967/en-us

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
  quit unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting Vista Blue Screen, error of JUDGMENT (and Windows 7)
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  Startup Options recovery or Windows 7 disk repair

  How to run a startup repair in Windows 7
  http://www.SevenForums.com/tutorials/681-startup-repair.html

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  How to create a Windows 7 system repair disc
  http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

  How to do a repair installation to repair Windows 7
  http://www.SevenForums.com/tutorials/3413-repair-install.html

  I hope this helps.
  --------------------------------------------------------------------------------------------
  Rob Brown - Microsoft MVP<- profile="" -="" windows="" experience :="" bicycle="" -="" mark="" twain="" said="" it="">

• Memory, databases and applications without head

  I've been struggling with this problem for some time now so let's go.

  As many of you know headless apps allowances of bunch of limit of 3 MB, which is fine, except when using Qt/Cascades objects that don't care much to consumption of memory, two examples are QNetwork and QtSql, who will blow easily your budget of memory in a single operation.

  I have simple ' SELECT * from Table' queries that consume more than 6MB, which then effectively disables the component without a head. More precise, I do the query the heap more than it consumes. So I tried libsqlite3, results were similar. It was however the promise to provide a chunck of mmap would or memory of static array for substitute of the bunch, but I can not:

  sqlite3_config(SQLITE_CONFIG_HEAP,...)

  to work correctly, it returns an error (1) every time.

  Unfortunately, I'm at the point where it seems that a component without head who uses SQL can be impossible with the current memory limit. Can anyone offer a solution to the use of SQL with headless while maintaining a service that runs reliably?

  -Are there when even to provide a static heap memory for QtSql use?

  -Are there a way to limit the memory used by QtSql?

  Thank you!

  EI

  The solution was to restructure my database, as awkward as this has been significantly reduced the memory required for the information necessary to satisfy the query of data in the buffer. In others, rather than have a huge database of the 8 column I broke it into several two databases colum - when the part without head wants just a little information is exactly what he will get so surprise elimination memory usage spikes.

  The problem still exists: as the database develops for a query memory requirements. Has no way to control the maximum limits memory use for QtSql complicating an app without elastic, even theoretically impossible to write head.

  EI

• Blue screen Memory Dump error - Windows 7 Professional 64 bit

  Hello

  I got the blue screen three times a week, the brand of my computer is Alienware M14X

  Signature of the problem:
  Problem event name: BlueScreen
  OS version: 6.1.7601.2.1.0.256.48
  Locale ID: 1033

  More information about the problem:
  BCCode: 1a
  BCP1: 0000000000041790
  BCP2: FFFFFA8001CEDE00
  BCP3: 000000000000FFFF
  BCP4: 0000000000000000
  OS version: 6_1_7601
  Service Pack: 1_0
  Product: 256_1

  Files helping to describe the problem:
  C:\Windows\Minidump\031615-91322-01.dmp
  C:\Users\Akkineni\AppData\Local\Temp\WER-170087-0.SysData.XML

  Read our privacy statement online:
  http://go.Microsoft.com/fwlink/?LinkId=104288&clcid=0x0409

  If the online privacy statement is not available, please read our offline privacy statement:
  C:\Windows\system32\en-US\erofflps.txt

  Please help me.

  Kind regards

  Aty.

  Hello

  If you are overclocking anything STOP! This is much like problems caused by
  Overclocking and heat related.

  BugCheck C4, {f6, 354, fffffa8010c16630, fffff880075a4f50}

  WARNING: Unable to verify timestamp for dne64x.sys
  ERROR: Module load completed but symbols can be loaded for dne64x.sys
  Probably caused by: dne64x.sys (dne64x + ff50)

  dne64x.sys as of 2008-11-10 deterministic Network Enhancer

  fffff880 '07595000 fffff880' dne64x of 1000 c 075 T (no symbol)
  Loaded symbol image file: dne64x.sys
  Image path: \SystemRoot\system32\DRIVERS\dne64x.sys
  Image name: dne64x.sys
  Timestamp: Mon Nov 10 17:01:24 (4918 964) 2008

  Bugcheck 1000007E, {ffffffffc0000005, fffff88006caf3ef, fffff880009e81c8, fffff880009e7a20}

  Probably caused by: nvlddmkm.sys (nvlddmkm + 29c3ef)

  nvlddmkm.sys on 01/09/2015 Nvidia video drivers.

  fffff880'06 has 13000 fffff880'07421000 nvlddmkm T (no symbol)
  Loaded symbol image file: nvlddmkm.sys
  Image path: \SystemRoot\system32\DRIVERS\nvlddmkm.sys
  Image name: nvlddmkm.sys
  Timestamp: Fri Jan 09 14:22:06 2015 (54B0548E)

  Bugcheck 50, {fffff8a012fd3fe8, 1, fffff88005f57609, 0}

  WARNING: Unable to verify timestamp for igdkmd64.sys
  ERROR: Module load completed but symbols can be loaded for igdkmd64.sys

  Could not read the name of the problem driver
  Probably caused by: igdkmd64.sys (igdkmd64 + 32e609)

  Igdkmd64.sys dated 12/12/2012 drivers Intel Graphics Accelerator

  "fffff880 ' 05 c 29000 fffff880 ' 061441a 0 igdkmd64 T (no symbol)
  Loaded symbol image file: igdkmd64.sys
  Image path: \SystemRoot\system32\DRIVERS\igdkmd64.sys
  Image name: igdkmd64.sys
  Timestamp: Wed Dec 12 16:42:26 (50 92472) 2012

  BiosVersion = A09
  BiosReleaseDate = 29/06/2012
  SystemManufacturer = Alienware
  SystemProductName = M14xR2
  Family = 103C_5335KV
  SystemVersion = A09
  SystemSKU = xxx123x #ABA
  BaseBoardManufacturer = Alienware
  BaseBoardProduct = M14xR2
  BaseBoardVersion = A09

  1. update all 3 of these pilots to Alienware and to sites the makers' real device.
  Check with the support of Nvidia and other OEMs for known problems. If no
  more recent, it may be necessary to go back to the old stable versions.

  2. Remove ALL power, and then reinstall the memory.

  3 try adding a fan blowing under the laptop to see what helps.

  4. If none of those is possibly a re-installation of Windows can help.

  5. check with Alienware support or a real computer store (that makes its own service in the workshop).

  Alienware - Support - drivers and downloads
  http://support.Dell.com/support/topics/global.aspx/support/alienware_support/alienware_support?s=DHS

  Alienware - Community Forum - Club
  http://en.community.Dell.com/Owners-Club/Alienware/default.aspx

  Rob - SpiritX

• SQLITE out of memory error

  Hi all

  I know there are some discussions about this, but they seem to be dead. I have attached a highlight of easy application and crued my problem.  Click the button and it will start operations.

  The problem im having is that I am getting large amounts of transaction (lots of 250 transactions) to a server to be applied to a database, inserts updates deletions etc.    It works for awhile, but will then blow with the out-of-memory exceptions.  The number of transactions can be reduced, but even that batch 1 transaction will result in the error.

  The application is made to be used for 5.0 devices and most any help would be greatly appreciated.

  See you soon

  PS. I don't there are suggestions to use System.GC() but that with no major problems on the cheek.

  Hi thanks for the suggestion, I tried it in the test project and it works, but I tried that in the main project, and she has not which leads me to believe their was another problem.

  I discovered that there was a scenerio where one of the instructions was not closed off which means the object was never being destroyed.

  Thanks for your help by highlighting this.

• IRLQ_LESS_OR_NOT_EQUAL_TO 0x000000A then proceeds to run a physical memory dump, I also get something related to memory and then STOP 0x0000001A and 0x00000DE

  Usually when playing games, DOTA 2 and Battlefield 3, I get them more when im playing battlefield 3.

  Hello

  Don't forget to check with the support of game manufacturers and ask in their forums to see if there is
  known problems.

  ---------------------------------------------------------------------------------------

  Results verified BlueScreenView WinDBG / DumpCHK.
  
  The Bug_Check have been in 0a, 1A, 7, 50 and.

  When there is that much material different from Bug_Check is almost always involved
  at least some of the issues.
  
  1. remove ALL power and then reinstall memory cards and cables (at both ends, where possible).
  in fact, remove and replace - don't do not just tight. Clean the dust bunnies and ensure that fans
  work. Try adding a small fan blowing into the socket to reduce the effects of heat (heat
  related not always means excessive heat that something might be too sensitive to the same
  normal levels).

  2. test the memory carefully using methods in the troubleshooters below. Keep in mind
  This memory tests only detect all errors as the moment where there are tiny speed differences
  between the modules that appear to be identical. It is necessary to test the modules in
  various combinations and models.

  3 several of the Bug_Check showed CAUSE nvlddmkm.sys who, in the Nvidia video driver.
  Search for Nvidia updates. See the driver update methods in the resolution of the problems previously posted
  above.

  NVIDIA - drivers - use OPTION 1 to manually enter your info driver to get the most recent drivers.
  http://www.nvidia.com/download/index.aspx?lang=en-us

  NVIDIA Support - check with the support that she might be a known issue
  http://www.nvidia.com/page/support.html

  NVIDIA forums - also check for the forums it might be a known issue or others likely to have
  http://forums.nvidia.com/

  4 check system Maker (manufacturer of motherboard for customized systems) updates to the BIOS,
  chipset drivers low level and major of edge and separate device drivers. Use DriverView
  -Microsoft drivers hide the value VIEW - updated those without emptying in their names. (See pilot
  methods of update in convenience stores previously posted.)

  5. after updating the drivers run DriverVerifier as shown in the troubleshooter below.

  6 use other methods of troubleshooting in convenience stores posted previously and those
  below as needed.

  ===========================================================

  BCCode: 0a 0x0000000A methods as well as updates to driver and memory tests
  are in the resolution of the problems previously shown.

  ===========================================================
  
  BCCode: 1a 0x0000001a

  Remove ALL power and reinstall all the memory cards and cables (both ends where possible).
  in fact, remove and replace - don't do not just tight. Make sure that the vents are clear and that the
  the fans are working. Even if the temperature is OK assume no heat does not affect the video,.
  sound or other system functions that it these get hot. Try adding a small fan blowing in
  the vents as a test. (These are especially for a PC not a laptop.)

  Have you recently added any hardware? Have you updated any drivers just before this started?
  (Check control panel - updates of Windows to see if all drivers have been updated it on the)
  This started the time) likely guilty hand are video driver, other great drivers, memory, and
  antivirus/antispyware/security products could be at fault as well as reader questions.

  Use the troubleshooter below and refer to the following message to drivers and memory when
  you get these sections and then back to the resolution of the problems according to the needs.

  BCCode: 1a 0x0000001a<-- read="" this="">
  http://www.faultwire.com/solutions-fatal_error/memory-management-0x0000001A-* 1041.html? order = votes

  ===============================================================

  BCCode: 7F 0x00000007E who is also a 0x1000007E

  See these KB articles:

  "Stop 0x0000007E" or "Stop 0 x 00000050" error message in Windows 7 or Windows Server
  2008 R2
  http://support.Microsoft.com/kb/979538

  "Stop 0x0000007E SYSTEM_THREAD_EXCEPTION_NOT_HANDLED" error when the GPU is under
  conditions of heavy load in Windows 7 or Windows Server 2008 R2
  http://support.Microsoft.com/kb/983615

  References to Vista also apply to Windows 7.

  BCCode: 7F 0x0000007E which is also 0x1000007E

  This error is usually a driver problem and display adapter (video) driver is the most suspicious if she
  may be others. Antivirus/antispyware/security programs, equipment (heat) and major software problems
  can also cause the error. When you get to the section of the driver to use the Troubleshoot utility my generic
  methods in the next message and then return to the if necessary troubleshooting tool.

  Have you recently added hardware or drivers updated? Don't forget to look in Control Panel - Windows
  Updates to see if all drivers have been updated it. Other donor opportunities include the antivirus/anti-
  spyware/security programs.

  When you get to the pilot and sections of the memory of the troubleshooter check the following message to
  update drivers and memory test and then return to the troubleshooter if necessary.

  BCCode: 7F 0x0000007E which is also 0x1000007E

  Cause

  SYSTEM_THREAD_EXCEPTION_NOT_HANDLED bug control is a very common bug control. TO
  interpret, you must identify which exception has been generated.

  Common exception codes are:

  • 0 x 80000002: STATUS_DATATYPE_MISALIGNMENT indicates an unaligned data reference was encountered.

  • 0 x 80000003: STATUS_BREAKPOINT indicates a breakpoint or ASSERTION was met when no kernel debugger was attached to the system.

  • 0xc0000005: STATUS_ACCESS_VIOLATION indicates a memory access violation has occurred.

  For a complete list of exception codes, see the Ntstatus.h file located in theinc directory
  the Microsoft Windows Driver Kit (WDK).

  Solve the problem

  If you do not have to debug this problem, you must use certain basic troubleshooting techniques.

  • Make sure you have enough disk space.
  • If a driver is identified in the bug check message, disable the driver or check with the
  • Reference of the manufacturer for driver updates.
  • Try changing video cards.
  • Check with your hardware vendor for updates to the BIOS.
  • Disable the BIOS memory options such as implementing caching or shading.

  If you plan to debug this problem, you may find it difficult to get a stack trace. Parameter 2
  (the address of the exception) must identify the driver or function that caused the problem.

  If the exception code 0 x 80000003 occurs, a hard-coded breakpoint or assertion was hit, but the system
  has been launched with the /nodebug. switch. This problem should occur infrequently. If it occurs repeatedly,
  Make sure that a kernel debugger is connected and the system is booted with the Switch/DEBUG .

  In case of exception code 0 x 80000002, the trap frame provides additional information.

  If you do not know the specific cause of the exception, consider the following questions:

  • Hardware incompatibility. Make sure all new hardware that is installed is listed in the
  • List of Microsoft Windows Marketplace tested products.
  • Service driver or defective peripheral system. A service driver or defective peripheral system can be
  • responsible for this error. Hardware problems, such as the incompatibilities of the BIOS, memory, conflicts
  • and IRQ conflicts can also generate this error.

  If a driver is listed by name in the bug check message, disable or remove that driver. Disable
  or remove drivers or services that have been recently added. If the error occurs during startup
  sequence and the system partition is formatted with the NTFS file system, you may be able to use safe
  Mode to rename or to delete the faulty driver. If the driver is used as part of the system startup procedure
  in Safe Mode, you must start the computer by using the Recovery Console to access the file.

  If the problem is associated with Win32k.sys, the source of the error may be a third remote
  control program. If this software is installed, you can remove the boot of the computer service
  by using the Recovery Console, and then by removing the offending system service file.

  Check the system log in Event Viewer for additional error messages that might help identify the
  device or the driver that generated the bug check 0x7E.

  You can also disable memory cache BIOS may try to resolve the error. You should also
  Run the diagnostics of material, especially the scanner memory, which provides the manufacturer of the system.
  For more information about these procedures, see the manual of your computer.

  The error that generates this message may occur after the first reboot during Windows Setup, or
  Once the installation is complete. A possible cause of the error is lack of disk space for installation and system
  BIOS incompatibilities. For problems during the installation of Windows that are associated with the absence of disc
  space, reduce the number of files on the disk drive hard target. Find and delete any temporary
  the files that you do not have to have files hidden Internet, backup application and.chkfiles files that
  contain fragments of file saved to disk scans. You can also use another hard drive with more drive
  free space for the installation. You can solve the problems of BIOS by upgrading the version of the system BIOS.

  BCCode: 7F 0x00000007E who is also a 0x1000007E<-- read="" this="">
  * 1141.html? order = votes http://www.faultwire.com/solutions-fatal_error/System-thread-exception-not-HANDLED-0x0000007E-

  ===============================================================

  BCCode: 50 0 x 00000050

  References to Vista also apply to Windows 7.

  Have you recently added any hardware? Have you updated any drivers just before this started? (Check
  Panel configuration-updates of Windows to see if all drivers have been updated it there all the time it started)
  Main likely culprits are video driver, other great drivers, memory and antivirus/antispyware/security
  products could be at fault as well as reader questions.

  Use the troubleshooter below and refer to the following message to drivers and memory when you get to
  These sections and then back to the resolution of the problems according to the needs.

  BCCode: 50 0 x 00000050

  Cause

  The BCCode 50 usually occurs after the installation of faulty hardware, or in case of failure
  hardware installed (usually associated with a faulty RAM, be it the main memory, L2 RAM cache memory, or)
  Video RAM).

  Another common cause is a defective system service installation.

  Antivirus software can also trigger this error, as can a corrupted NTFS volume.

  Solve the problem

  Solve a defective hardware problem: If the material has been added to the system recently,
  Remove to see if the error recurs. If existing hardware has failed, remove or replace
  the defective component. You must run the diagnostics of material provided by the manufacturer of the system.
  For more information about these procedures, see the manual of your computer.

  Fix a defective system service: Disable the service and confirm that this
  resolves the error. If so, contact the manufacturer of the service on a possible system
  Update. If the error occurs during the system startup, restart your computer, and press F8 to
  character mode menu that displays the choice of operating system. As a result
  Windows Advanced Options, select last good known Configuration option menu.
  This option is most effective when a pilot or a service is added at a time.

  Solve a problem of antivirus software: Disable the program and confirm that this fixes
  the error. If this is the case, contact the manufacturer of the program about a possible update.

  Fix a corrupted NTFS volume:  Run Chkdsk /f /r to detect and repair disk
  errors. You must reboot the system before the start of the analysis of disk on a system partition. If
  the hard drive is SCSI, check for problems between the SCSI controller and the disk.

  Finally, check the system log in Event Viewer for additional error messages that might help
  identify the device or driver that generated the error. Disable the cache in memory of the BIOS
  could also resolve it.
  
  BCCode: 50 0 x 00000050<-- read="" this="">
  * 1095.html? order = votes http://www.faultwire.com/solutions-fatal_error/page-fault-in-NONPAGED-Area-0x00000050-

  ===============================================================

  BCCode: OF 0x000000DE

  This is usually a driver issue then run DriverVerifier and check the drivers using the methods
  in troubleshooting below. Carefully check the memory using the methods below.

  BCCode: OF 0x000000DE

  Bug Check 0xDE: POOL_CORRUPTION_IN_FILE_AREA

  Bug POOL_CORRUPTION_IN_FILE_AREA control has a value of 0x000000DE. This indicates that a driver has corrupted the memory pool that is used to maintain pages to disk.

  Important information if you have received a STOP Code

  If you have received a blue screen error, or stop code, the computer stopped abruptly to protect against data loss. A hardware device, its driver or software might have caused this error. If your copy of Windows is shipped with your computer, contact your computer manufacturer. If you purchased Windows separately from your computer, Microsoft provides support. To find contact information for Microsoft or the manufacturer of your computer, Contact Support.

  If you have experience with computers and try to recover from this error, follow the steps in the Microsoft article solution STOP (blue screen) errors in Windows.

  The following actions could prevent a mistake like this does not happen:

  1. Download and install updates for your computer from Windows Update device drivers.
  2. Scan your computer for computer viruses.
  3. Check your hard drive for errors.

  POOL_CORRUPTION_IN_FILE_AREA settings

  None

  Cause

  When the memory dereferenced Manager the file, he discovered this type of corruption of memory pool.

  BCCode: OF 0x000000DE<-- read="" this="">
  * 1221.html http://www.faultwire.com/solutions-fatal_error/A-Driver-corrupted-pool-Memory-used-for-Holding-pages-0x000000DE-

  ===================================================

  Driver Verifier can help find some BSOD problems:

  Using Driver Verifier to identify issues with Windows drivers for users advanced
  http://support.Microsoft.com/kb/244617

  How to solve the problems of driver in Windows Vista or 7.
  http://www.WinVistaClub.com/T79.html

  Using Driver Verifier
  http://msdn.Microsoft.com/en-us/library/ff554113 (v = VS. 85) .aspx

  How to use Windows drivers check Manager to solve problems and identify the Driver questions
  http://www.YouTube.com/watch?v=_VwIDD9xngM

  Driver Verifier
  http://www.techsupportforum.com/2110308-POST3.html

  Using Driver Verifier
  http://www.faultwire.com/solutions/using_driver_verifier.php

  How to use Windows drivers check Manager to solve problems and identify the Driver questions
  http://www.YouTube.com/watch?v=_VwIDD9xngM

  You can disable the driver verifier
  http://support.Microsoft.com/kb/244617

  Start - type in the box search-> auditor/Reset hit enter to disable

  BlueScreenView lets you know if there is a driver specified in the error message. Also check with
  MyEventViewer at the blue screen.

  If DriverVerifier creates a minidump upload it and post the link here so we can analyze.

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Memory will not work Diagnostic tool - black screen

  Hello

  I'm having a problem with my (relatively) new - an ASUS laptop UX - 21F. It worked very well for the first three months, but only in the last week has crashed several times on me with a BSOD. Unfortunately, Windows (Win7 Ultimate) does not create the memory dump file as it is currently specified to do so. (Yes, I checked, double-checked and rechecked re this parameter.) It simply does not create the image file.) Looking back through the event log, it does not match what is happening just before failure. It seems to be random.
  It sounded like a potential RAM for me, so I thought I'd run the Windows Memory Diagnostic tool. I chose restart immediately and... nothing. It restarts, messages and then it is a black screen and high enough system fan wind rising and the system gets hot enough. There is no cursor, or anything like that, and the only thing we can do is to hit the power button (it instantly stops, rather than having to four seconds). When it restarts, the system boots normally into windows.
  I tried to access the tool in many different ways and there seems to be no way to enforce. Each way I just get a black screen and a hot computer.
  What should I do here? I do a lot of development on this machine and I'm kind of falling ill to endorse things up to four times a day in case it crashes and I lose my job. Should I reinstall the OS and see if the problems go away? Or is there something less invasive than I do?

  Download and create the CD to boot from here:

  Memtest86 + http://www.memtest.org/

  If you have more than one piece of RAM in it, blow an and boot from the CD. If there are no errors, swap out with another room and boot on the CD again.

  Look in the event log at the time of the accident and see what are the entries for error there. This might give you a clue as to what is happening.

  Is the ' (relatively) new laptop "still under warranty by any chance? If so, you should also contact ASUS or the place you bought it from.

  SC Tom

• DB face memory pressure and need more memory?

  
  Hi all

  DB: 10g and 11g

  Need your advice.

  We provide the server db use memory and cpu management report on monthly basis.

  Average usage of memory the server is more or less the same each month that memory allocated to oracle is capped (for example, memory_target).

  Therefore, we will not be able to tell if the memory allocated to the sufficient DB and when does more memory?

  We are required to provide a usage report to show that the memory allocated to the database itself is enough on monthly basis and does not need to bulk up.

  Is there a good way to provde this?

  Our DBs are all OLTP and rarely do full scan.

  First thought to provide the trend of BHCR (above 90%, this means memory is sufficient). Read a large number of documents that BHCR is no longer useful.

  A better way to do it? Kindly share your experiences.

  Thank you

  You can keep in mind what the different parts of the memory.  The SGA is a shared resource, which includes the areas of code and data, and even those who can interleave in pressure of circumstances.  The PGA is determined by the use of the users.  The trend of the latest versions of Oracle is spending more major requests for data at the PGA, but which cannot affect you much if you're like really OLTP, as you describe (which one silent report or batch could blow).  So really, after getting the right CMS, the PGA is more likely to be affected by the increase in the number of users.  Mechanisms of the target to be fairly stable systems (as well as assignments of similar resources carried out by reasonable operating systems) translated well enough glancing SGA and PGA advice and after it.

  Using the resources on a system close to their means of amount maximum, there are times when performance will go downhill fast, simply because of a resource to bite.  (For a good time in mathematics, see the white paper to think clearly on Cary Millsap's performance.)  These types of problems can come from many sources, if a regime change, hardware malfunction or a simple increase in its attendance.  Those who dance near the line will inevitably have to step on it, or some such maxim comes from jurisprudence.

  So the desire of the management of the Non-becassine-hunt is to anticipate and avoid such problems without too much purchase hardware or compulsive, disorder of tuning.  The idea is to make an analysis of trends which allows to predict that an increase in its attendance will make things down a steeply, to do what is necessary to avoid it (or at least expects).

  Oracle has a report to do this?  Not really.  There are too many variables and too many ways to use and abuse a system.  Most performance problems are SQL issues.

  What you can do is to simulate accurately the workload on a test system, increasing its failure.  This as an exercise in iterative parameterization can give a good idea of what settings are required in order to maximize what you can use and an idea what kind of use will start demanding more material.  For a well designed system, it can be as simple as looking at the number of users and uses of the pga.