Microsoft Defender is blocking the start of digital line (DLG.exe) by Avanquest Software detection

Similar Questions

• SMU-6556 - how to control the rise in digital lines (hsdio) time

  Hello

  Is it possible to control the rise in digital lines SMU-6556 time?

  Even in a low frequency 10 kHz signal rise time is 2ns.

  TKS,

  Hello engfpe,

  The SMU-6556 is a 50 Ohm system, which means that the output is source series finished to be 50 Ohms and all our cables and accessories are 50 Ohms.  With this configuration, regardless of the flow of data, you should have a clean edge up or down, regardless of the data rate. The quality of the production (edge up or down) on your device is related to the adaptation of impedance of your cables.

  The SMU-6556 cannot adjust the speed of scanning by itself.  However, you can insert simple passive components to do it for you.  I have attached below the images.  The first is a diagram showing a way to slow down the edge.  The second is the a waveform simulation showing the rate of original edge before it slows down and the edge of idle.   This simulation is not the SMU-6556 but rather a generic digital output for concept.  In the schema that R1 is set on 34 Ohms because U1.8 has the 16 additional Ohms on the inside.  TL1 is the output of 50 ohms simulating the cable on the SMU-6556.  R2, R3, and C1 are components, you can insert after the SMU-6556 twist before moving your device/cable.  In this configuration from cable to your device is TL2 which is also 50 ohm, but it could be another impedance in which case you would change R3 to match.

  You can see in the attached images, you can slow down significantly the edge with this configuration by altering the C1.  I hope this helps.

• How can I use internal clock case OR USB - 6259 BNC for the acquisition of digital data in my own big software?

  I want to integrate the ANSI C sample program ReadDigPort - ExtClk.c in my own big package.

  I want to use the internal clock of the BNC NI USB-6259 (.. 80 kHz 120 kHz).

  In the document:
  High speed M: Series Multifunction DAQ for USB - 16-bit, up to 1.25 MECH built-in BNC connectivity. / s,.
  is written:
  Or sample DI source clock: Any PFI, RTSI, HAVE sample or convert clock, AO, Ctr n out internal and many other signals sample clock
  The digital subsystem doesn't have its own dedicated internal synchronization engine. Therefore, a sample clock must be provided another subsystem on the device or from an external source.

  How can I use internal clock case OR USB - 6259 BNC for the acquisition of digital data in my own big software?
  With what other subsystem on the device can generate a source of the clock? How?

  It is possible to set a clock on an internal counter (for example ' Dev1/ctr0"):
  Creates channels to generate digital impulses that define the freq and dutyCycle and adds the channel of the task that you specify with taskHandle.
  DAQmxCreateCOPulseChanFreq (taskHandle, "Dev1/ctr0" units, clockName, idleState,
  initialDelay, freq, the duty cycle); works

  But it is not possible to drive this internal clock to a terminal (for example "/ PFI0/Dev1"):
  DAQmxErrChk (DAQmxCreateCOPulseChanFreq (taskHandle, "/ PFI0/Dev1", clockName, units, idleState, '))
  initialDelay, freq, the duty cycle); does not work: error DAQmx: measurements: type I/O of the physical channel does not match the type of I/O required for the virtual channel you create. Name of the physical channel: PFI0. Name of the virtual channel: clock

  The sample clock source can be derived from an external terminal (for example "/ PFI0/Dev1"):
  Sets the source of the sample clock, the sample clock rate and the number of samples to acquire or generate.
  DAQmxCfgSampClkTiming (taskHandle, "/ PFI0/Dev1", maximumExpectedSamplingRate, DAQmx_Val_Rising, ")
  DAQmx_Val_ContSamps, bufferSize); works. Acquire or generate samples until you stop the task

  But it is not possible to derive the internal counter of the clock (for example ' Dev1/ctr0"):
  DAQmxCfgSampClkTiming (taskHandle, "Dev1/ctr0", maximumExpectedSamplingRate, DAQmx_Val_Rising,
  DAQmx_Val_ContSamps, bufferSize); does not work. Error: Acquire or generate samples until you stop the task: make sure that the name of the terminal is valid for the specified device. See Measurement & Automation explore valid names of terminals. Property: Property of DAQmx_SampClk_Src: DAQmx_SampClk_ActiveEdgeSource device: Terminal Source Dev1: Dev1/ctr0

  Hi datafriend,

  using what it says is correct:

  Or sample DI source clock: Any PFI, RTSI, HAVE sample or convert clock, AO, Ctr n out internal and many other signals sample clock
  The digital subsystem doesn't have its own dedicated internal synchronization engine. Therefore, a sample clock must be provided another subsystem on the device or from an external source.

  This means that if you do not use an external signal as clock you can use the sample clock to HAVE it on board or at the output of the internal counter.

  There are also 2 ANSI C examples in this regard:

  http://zone.NI.com/DevZone/CDA/EPD/p/ID/4485

  http://zone.NI.com/DevZone/CDA/EPD/p/ID/4488

  So in both cases you have to use a fictitious task you need only for the generation of the internal clock (HAVE or CTR)

• Game homepage has advertising column that is blocking the start of the game

  I have two favorite whose home pages games I saved as shortcuts on my laptop. Before moving on to Firefox, I could start a game immediately upon entering the site. Now, whenever I have pull the games up, a column of annoying ads appears on the left side of the screen, blocking access to the start key to the free game. I could not find a way to remove this column.

  https://adblockplus.org/en/about

  https://addons.Mozilla.org/en-us/Firefox/addon/Adblock-Plus/?src=SS

• Coincide the start of digital and analogue tasks in c#

  Hi all

  I cannot synchronize the start of an analogue and digital output special in c#. Specitifically, I created a task master analog output and output a task digital slave that uses the sample of the task of the AO clock. Everything works fine except there is always a random between signals delay because they are triggered to start separately in the software. I would like to start both tasks with the same trigger signal.

  I think that I should do something like:

  digitalTask.Triggers.StartTrigger.ConfigureDigitalEdgeTrigger("Dev2/ao/StartTrigger",DigitalEdgeStartTriggerEdge.Rising);

  analogTask.Start ();

  but DAQmx is throwing an error message saying that my source Tigger is not valid. What is the correct idea? What is the exact syntax for inputing the source of relaxation. Thanks a lot for all the help!

  -Jon

  Hi Jon-

  If you have the sample shared between the two tasks clock, you should be able to start the slave task first, in this way when the master task starts, the task of the slave will begin taking samples on the same edge of clock.  You should not use a trigger to start.

  However, if you try to import an external trigger, connect to a PFI line and specify "Dev2/PFI0' as the command source for the two tasks (or whatever the PFI line you've hooked the trigger until the).

  I hope this helps.  Good luck with your application!

• Microsoft Word pinned to the Start Menu do not open the menu in the right sidebar

  With Excel in my Start menu when I put my cursor over them or click on the right arrow all my pinned documents appear.  Microsoft Word used to do that, but now nothing happens if I put my cursor over them or click the right arrow.  He worked and suddenly stopped.  Any suggestions?  All other start icons show documents pinned and recent programs or non-Microsoft.  I tried to remove it and then put it back and restarted my computer and tried again, neither worked.  Thank you.

  ... Word used to do that, but now nothing happens if I put my cursor over them or click the right arrow. He worked and suddenly stopped...

  This seems to be a little corruption in the history of the document, but first check your Recent Documents . You decided to keep it a secret, your version of Word so here are a few tracks for Word 2007.

  With Word open to a blank document, click the Office button , then click on Word Options in the lower right. Select Advanced from the list on the left and scroll down to the section display halfway, the right pane. Check the next number of show this number of recent documents: to ensure that it is above zero. If it is zero, to increase the number to something you want to keep, and then click OK at the bottom right.

  If the show this number of recent documents: setting was already above zero, there may be a small file corruption in historical data. Frequent data section the Jump lists are stored in this folder,

  %AppData%\Microsoft\Windows\Recent\AutomaticDestinations

  Click Start or press the Windows key and type or the location of the folder in the program files , then click on paste . Then, find and delete the fle

  adecfb853d77462a.automaticDestinations - ms

  Who must provide recent documents for Word Launcher in the Start Menu. If you can't find the file, try to clear all the files and restart the computer. Subsequent use of Word and other added elements should repopulate the lists.

  • "Have you tried it turned off then on again? '-'The IT Crowd' Roy (Emmy award-winning British comedy)

• Why won't my Microsoft keyboard work during the start sequence () trying to get into the BIOS)?

  When you start up/reboot my system, my Microsoft Natural Wireless ergonomic Kayboard 7000 does not work to thus preventing me the ability to get into the BIOS to make the necessary changes. Can do something about it? Before ask you, Yes, legacy USB support is enabled.

  This problem is usually a problem with the BIOS Setup.  Several BIOS can have different settings to enable / disable the USB keyboard / mouse access.  These tend to be listed as:

  Use USB legacy...

  Activate USB keyboard...

  It is a major problem with motherboards that have the old PS/2 ports for keyboard / mouse.

  Also, I found that if your keyboard is not directly connected to a rear USB port, you may have this problem.

  And according to the number of devices USB is connected to your PC, if you 'maxed out' device (all ports used), your keyboard is not working as it should during the windows "pre-seed" process (including the BIOS screens "P.O.S.T.".)

• Have a Microsoft Lifecam and he just started to have a Lifecam.exe is not working error

  LifeCam.exe does not work correctly and will close its doors has just begun to burst yesterday.  I have all the updated drivers and firmware.   I have no new schedule.  He began to appear while I was skyping with my wife.  Sometimes, I push the buttons to confirm and Skype still works with video and mic.  But I can't open the lifecam program more.

  The only thing that I would do a wipe my system and start from scratch.

  Hello

  Try the following steps:

  Step 1: Put the computer to boot to determine the software causing problem

  
  Followstep 1 in the link below,
  How to troubleshoot a problem by performing a boot in Windows Vista or Windows 7 :
  http://support.Microsoft.com/kb/929135

  If everything works well after a clean boot, you can deduce that some third-party services are at the origin of the problem.

  Continue with the remaining steps to pin-point on the third party service.

  After find you the program that is causing the problem, you need to maybe update or install a newer version of the program, if you rarely use this software, you can consider
  Uninstall.
  
  Important: n ' forget not the computer to start normal follow step 7 in the link.

  If the problem persists,
  Step 2: Download and install the latest version of the life CAM software
  http://www.Microsoft.com/hardware/downloads/default.mspx

  Step 3: Follow the steps mentioned in the article below which solves the following problem:

  The problems of compatibility between life Cam and other programs
  http://support.Microsoft.com/kb/953692

   

  Kind regards
  Afzal Taher - Microsoft technical support.
  Visit our Microsoft answers Feedback Forum and tell us what you think.

• MS word offers the option of Microsoft Word 2010 (2) in the list of the start menu

  Original title: program registration under Start button

  Today, when I was looking for a program that is displayed when I select the Start button, I noticed that the number 2 see the next to registration for Microsoft Word 2010.  It looks now like this: Microsoft Word 2010 (2)

  I don't think it was like that the other day when I finally used Word.  Any ideas on why it would start that looks like this?  I made no changes to my computer.

  I use Microsoft 7 Home Premium.

  Thanks in advance.

  Hey Debba,.

  -You have two entries in the start menu for Microsoft Word? One is Microsoft Windows Word 2010 (2) and the other is Microsoft Word 2010 Microsoft Office on the start menu?

  -Is this Microsoft Word 2010 (2) successfully opened?

  -This happens to you with other programs in the list?

  If there are two icons for Microsoft Word 2010 on the Start menu, remove the icon of Windows of Microsoft Word 2010 (2).

  All you have to do is click on Microsoft Word 2010 (2) and click on remove from this list.

  This seems to be only a Microsoft Word 2010 shortcut added to the list of the start menu.

  Hope this information helps. If you have any questions, please let us know.

• need help for the start up programs etc too of > > > >

  I am currently using Ccleaner as my msconfig works not what me hae questioned here in any case there are 3 categories of start they are; Windows, internet explore and scheduled tasks, can someone tell me which ones I can disable

  Windows.
  Yes HKCU:Run CTFMON. EXE C:\windows\system32\ctfmon.exe
  Yes HKLM:Run Adobe ARM "C:\Program Files\Fichiers Files\Adobe\ARM\1.0\AdobeARM.exe"
  Yes HKLM:Run ArcSoft Connection Service C:\Program Files\Common ArcSoft Service\Bin\ACDaemon.exe
  Yes HKLM:Run CTSVolFE.exe "C:\Program Files\Creative\Mixer\CTSVolFE.exe" / r
  Yes HKLM:Run Dell QuickSet C:\Program Files\Dell\QuickSet\quickset.exe
  Yes HKLM:Run ehTray C:\WINDOWS\ehome\ehtray.exe
  Yes HKLM:Run HotKeysCmds C:\WINDOWS\system32\hkcmd.exe
  Yes HKLM:Run IgfxTray C:\WINDOWS\system32\igfxtray.exe
  Yes HKLM:Run IntelWireless "C:\Program Files\Intel\Wireless\Bin\ifrmewrk.exe" /tf Intel PROSet/Wireless
  Yes HKLM:Run IntelZeroConfig "C:\Program Files\Intel\Wireless\bin\ZCfgSvc.exe".
  Yes HKLM:Run MSC "c:\Program Files\Microsoft Security Client\msseces.exe" - hide - runkey
  Yes HKLM:Run persistence C:\WINDOWS\system32\igfxpers.exe
  Yes HKLM:Run SigmatelSysTrayApp %ProgramFiles%\SigmaTel\C-Major Audio\WDM\stsystra.exe
  Yes HKLM:Run "C:\Program Files\Common Java Update\jusched.exe" SunJavaUpdateSched
  Yes start common digital line Detect.lnk C:\Program Files line Detect\DLG.exe

  Internet Explorer
  Yes the Blog Extension this C:\Program Files\Windows Live\Writer\WriterBrowserExtension.dll
  Yes Extension diagnose connection problems... %windir%\Network Diagnostic\xpnetdiag.exe
  Yes expansion Messenger C:\Program Files\Messenger\msmsgs.exe
  Yes search Extension C:\PROGRA~1\MICROS~2\OFFICE11\REFIEBAR. DLL
  No Skype Extension click to call C:\Program Skype skypeieplugin.dll
  Yes Helper AC - Pro C:\Documents and Settings Settings\doug\Application Data\Complitly\AutocompletePro.dll
  Yes to support Adobe PDF link Helper-C:\Program Files\Common Files\Adobe\Acrobat\ActiveX\AcroIEHelperShim.dll
  Yes to support Google Toolbar Helper-C:\Program Files\Google\Google GoogleToolbar_32.dll
  Yes to support Google Toolbar notify BHO-C:\Program Files\Google\GoogleToolbarNotifier\5.7.7227.1100\swg.dll
  Yes Helper Java (TM)-plug-in 2 SSV Helper-C:\Program Files\Java\jre6\bin\jp2ssv.dll
  Yes Helper Java (TM)-plug-in SSV Helper-C:\Program Files\Java\jre6\bin\ssv.dll
  Yes Helper Class JQSIEStartDetectorImpl-C:\Program Files\Java\jre6\lib\deploy\jqs\ie\jqs_plugin.dll
  No Skype Browser Helper C:\Program Skype skypeieplugin.dll assistance
  Yes to support Windows Live Sign - in Helper C:\Program Files\Common Files\Microsoft Shared Windows Live WindowsLiveLogin.dll
  Yes the toolbar Google Toolbar C:\Program Files\Google\Google GoogleToolbar_32.dll

  Scheduled tasks
  Yes the task FacebookUpdateTaskUserS-1-5-21-1220945662-573735546-839522115-1003Core C:\Documents and Settings\doug\Local Settings\Application Data\Facebook\Update\FacebookUpdate.exe/nocrashserver/c
  Yes the task FacebookUpdateTaskUserS-1-5-21-1220945662-573735546-839522115-1003UA C:\Documents and Settings\doug\Local Settings\Application Data\Facebook\Update\FacebookUpdate.exe /ua /installsource scheduler
  Yes the task GoogleUpdateTaskMachineCore C:\Program Files\Google\Update\GoogleUpdate.exe/c
  Yes GoogleUpdateTaskMachineUA C:\Program Files\Google\Update\GoogleUpdate.exe /ua /installsource Task Scheduler
  Yes the task antimalware software of Microsoft scheduled scan c:\Program Files\Microsoft Security Scan of Client\MpCmdRun.exe - ScheduleJob - RestrictPrivileges
  Yes the task MpIdleTask c:\Program Files\Microsoft Security Client\MpCmdRun.exe - IdleTask TaskName - MpIdleTask
  Yes the task photopadShakeIcon C:\Program NCH Software\PhotoPad\photopad.exe - shakeicon

  Please let me know if I can disable some and what I can disable without is doing something important... Thanks for your help.

  Yes HKLM:Run Adobe ARM "C:\Program Files\Fichiers Files\Adobe\ARM\1.0\AdobeARM.exe"
  Yes HKLM:Run ArcSoft Connection Service C:\Program Files\Common ArcSoft Service\Bin\ACDaemon.exe
  Yes HKLM:Run CTSVolFE.exe "C:\Program Files\Creative\Mixer\CTSVolFE.exe" / r
  Yes HKLM:Run Dell QuickSet C:\Program Files\Dell\QuickSet\quickset.exe
  Yes HKLM:Run ehTray C:\WINDOWS\ehome\ehtray.exe

  Yes HKLM:Run SigmatelSysTrayApp %ProgramFiles%\SigmaTel\C-Major Audio\WDM\stsystra.exe
  Yes HKLM:Run "C:\Program Files\Common Java Update\jusched.exe" SunJavaUpdateSched

  Yes the task GoogleUpdateTaskMachineCore C:\Program Files\Google\Update\GoogleUpdate.exe/c
  Yes GoogleUpdateTaskMachineUA C:\Program Files\Google\Update\GoogleUpdate.exe /ua /installsource Task Scheduler
  Yes the task photopadShakeIcon C:\Program NCH Software\PhotoPad\photopad.exe - shakeicon

  I would disable them. but you have to download Autoruns:

  Use Autoruns to understand this all starts when your computer's / when you log in.  Look for whatever it is you do not know using Google (or ask here.)  You can hopefully figure out if there are things from when your computer does (or connect) you don't not need and then configure them (through their own built-in mechanisms is the preferred method) so they do not - start using your resources without reason.

  You can download and use Process Explorer to see exactly what is taking your time processor/CPU and memory.  This can help you to identify applications that you might want to consider alternatives for and get rid of all together.

  More info comes from Stanley S. and it should help you before you decide who to disable.

  Only startup items that I run are elements of microsoft.

  To demand the same tasks.

  Solutions Explorer, it seems that you have too many toolbars for me, but you should get each of them to see if you want it to run as an add-on, you could also disaable each addon one at the time and the surf for a while and if all is ok, leave this option unchecked.

• Can PCI 6602:How I use digital lines of the Board of Directors and at the same time to generate trains of pulses by using a meter?

  Hello!

  My problem appeared when I tried to update my traditional NOR-DAQ legacy code to DAQmx.

  I use 2 meter (meter 5 and 7 meter) on PCI-6602, to generate trains of pulses, as well as the lines of e/s digital port 0 (the form lines from 0 to 7). What I do in my request, it's that I'm starting to generate the pulse train on the output of 2 meters and after that I play with the State of digital lines.

  Traditional, it was no problem to use the meters and digital lines at the same time, everything went perfectly, but in DAQmx, is not possible.

  What's happening: I start generating train of pulses on the output of counters, no errors, but when I try to change the State of a line of digital port the generation of the pulse train is stopped. What happens when I start the task associated with the digital way.

  My question is: is it possible to create a channel on digital lines without changing the channels created for meters?

  Another thing that I managed to do with the panels 'Measurement and Automation Explorer' and Test for PCI-6602, is basically the same thing, I generate trains of pulses on the output of the 7 meter and try to start a job on the digital line, but I get an error:

  "Error-200022 occurred in test Panel.
  Possible reasons:
  Measurements: Resource requested by this task has already been reserved by another task.
  Device: Dev4
  "Terminal: PFI8.

  On the contrary if I use the counter 0 or a counter 1 to generate trains of pulses I encounter the same problem.

  What resources are used by 2 to 7 of the PCI-6602 card counters and the counters to 0 and 1 do not use?

  Thanks in advance for any answer!

  Ciprian

  After doing some real tests on this device, I found that it is a normal behavior for the jury of 6602.  This is because when you start a task digital all 32 lines are configured for digital i/o, so it replaces your meter operation.  The article below the link explains a little more on this subject.  You must start the digital task before the task of counter to use the features of both in your program.

  2 meter and above will not work correctly when you perform digital i/o on NI 6601 or 6602

  http://digital.NI.com/public.nsf/allkb/43F71527765EEC3886256E93006CD00C?OpenDocument

• The Start button is not visible on the taskbar and items on the computer display in large.

  PC screen too big... taskbar disappeared, but I came back... but the Start button did not return

  original title: too big screen - AutoScan not visible

  Hi Molly D.,.

  Thanks for posting your query in the Microsoft Community.

  The Start button gives you easy access to the applications and programs on the computer. You have a problem with the Start button is missing on the computer. It can be difficult when something that is important to you does not work as expected. It's pretty simple and we're here to help you solve the problem. We work as a team and get this sorted out.

  Please answer the question-

  (1) is the big screen of the computer at any time on the computer or is it limited to Internet Explorer?

  (2) that you get an error message or error code?

  (3) how have you managed to return to the taskbar?

  (4) have you done other changes on the computer before the show?

  I would like more information about the issue.

  Method 1-

  I wish that you follow the steps in the article-

  http://support.Microsoft.com/kb/318027#top

  Note: Make sure that get you the computer to a Normal startup after performing all the troubleshooting steps.

  Make sure you get the computer back to Normal Mode after performing all the troubleshooting steps.

  The antivirus will try to repair bad sectors on the hard drive damaged by viruses. All the data on these areas will be lost in the process.

  Make sure that you back up the data on the computer before you continue.

  Method 2-

  You must return the item to change the size of the screen-

  Change the resolution of your monitor

  http://Windows.Microsoft.com/is-is/Windows-XP/help/Setup/change-monitor-resolution

  To increase or decrease the size of objects and text on your screen

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/display_use_large_or_small_fonts.mspx?mfr=true

  To change your screen resolution

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/display_change_screen_resolution.mspx?mfr=true

  We know if you need help. We will be happy to help you. We, at tender Microsoft to excellence.

  Thank you.

• At the start of the system, the message says C:users\Rose\ Appdata\Local\Mozilla\MicrosoftHelp\pcwfrqgt.dll I already deleted Mozilla and Firefox

  I uninstall Mozilla and Firefox a few months ago and keed get the same message at startup listed above.

  Hello

  How do you uninstall Mozilla Firefox?

  I suggest you to check if Mozilla Firefox is always installed in programs and features:

  http://Windows.Microsoft.com/en-us/Windows-Vista/uninstall-or-change-a-program

  Perform the steps mentioned below and check if that helps:

  Method 1:

  Please check if the problem still persists in safe mode too. See the link below for more information about safe mode:

  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  Method 2:

  Try to do a Scan SFC (System File Checker). The scan will look bad system files and will attempt to fix them, if possible.

  (a) click the Start button.
  (b) type: cmd.exe in the search results.
  (c) right click the cmd.exe file and select 'run as administrator '.
  (d) in the CMD window, type: sfc/scannow and press the Enter key.
  (e) restart and see if that solves the problem.

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833

  Let us know if it helps.

• pin the start menu website

  There are three sites listed in my Start Menu that are incorrectly typed. Attempts to remove them as usual absolutely no results. They just sit there, constantly, aggravatingly using space that I prefer to use for something else.

  Is it possible to withdraw outside the right click and click on delete from the list that does not work on this pc.

  Operating system is Windows 7 Home Premium.

  Hi again!

  Please start by back up the registry. How you do that, that is described here: http://pcsupport.about.com/od/windows7/ht/backup-registry-windows-7.htm

  Then, create a restore point. How you do that, that is described here: http://windows.microsoft.com/en-us/windows7/create-a-restore-point
  Now you can try it without risk of finding the registry entry.
  Type regedit in the search in the start menu and choose regedit.exe by clicking on it.
  You are now in the registry editor.
  On the left side under the computer, click on the small arrow next to HKEY_CURRENT_USER to expand a list of items. Search for software and to extend it again by clicking on the small arrow next to him. Now search Microsoft, it redevelop and image search for Windows. Expand it and look for the current Version. Expand it and seek to explore. Expand it and look for Startpage2.
  Note: on the bottom of the window, the following path should now appear: Computer\HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Explorer\StartPage2

  Now, left-click on the 2 home page and search Favorites in the right part of the window. Click on, and then choose delete all values starting with 'Favorites '.

  Now your StartMenu must be empty, and you can begin to pin anything you want here.

  I hope this helps!

  See you soon
  Julia

• 0 x 80070424 error message when I click on the 'Start' button to Microsoft Defender.Please Help

  My Microsoft Defender is orange. I clicked on "Start" and received the error message 0 x 80070424. I don't know what is happening. How to restore my WDefender? I have no idea what about if I'm BETA or not. I went with BETA.

  Check the following and tell us what program you are referring and maybe we can determine what your question is about:

  http://securitygarden.blogspot.com/2012/04/understanding-Microsoft-anti-malware.html

  Kind regards...