models of LabVIEW for compact RIO

Similar Questions

• Reading Configuration files using Labview RT in a Compact RIO

  Hello

  I am very new to Labview RT/Compact RIO development platform and happen to have a question. I will develop an application in Labview RT / FPGA that will make several simulations. However some these simulations can produce different results depending on the configuration settings. Our systems generally run in a Windows application, were there is a configuration (usually in XML format) file that the application reads and analyzes the given parameters. I was wondering if there is something similar, that I can do it, in which I have a configuration file that can be read before my Labview RT/FPGA application initialization, to change the simulation.

  Thank you

  Mario

  Hi Mario,.

  That's right, there are screws for the files .ini on real-time targets.

• Basis of LabVIEW Development with Compact RIO device software

  Hello.  Currently, I have the LabVIEW Base development software package and have been using it with DAQ Compact devices for the acquisition of basic data.  I would now like to start integrating controls in my system, changing to RIO Compact for deterministic real-time features.  My question is that I would be able to build applications for the Compact RIO system using only the basis of LabVIEW Development package without updating immediately?  Maybe some features are not available for me, but could at least get a good start like that?

  A CompactRIO embedded time real operating system (RTOS) called VxWorks you need to target the deployment of LabVIEW code to the device. Classic LabVIEW screws you will have been written so far are built to target general purpose operating systems (GPO) such as windows.

  To create screws that are deployable to STSOp, you will need the real-time Module that is not included in the basis of LabVIEW. As a result, to take advantage of the embedded FPGA, you'll need to install the LabVIEW FPGA Module as well.

  As long as you have the FPGA modules and in real time, it seems to me that you should be able to control these devices with LabVIEW Base. Without these software components you will not be able to create an instance of the device target your LabVIEW project.

• LabView is in real-time for Compact FieldPoint necessary?

  Hello!

  LabView is in real-time for Compact FieldPoint (CFP) necessary?

  (in German: Ist für die von Compact FieldPoint LabView time use real necessary?)

  Thank you.

  Bye, Ouafa

  Hello

  If you just want to use Labview for logging and graphics (via Ethernet) AND that you do NOT use a CFP-real-time controller, you don't need to LabVIEW Real-time.

  For example if you use OR cFP-1804-Ethernet/Serial Interface for Compact FieldPoint.

  (http://sine.ni.com/nips/cds/view/p/lang/en/nid/202527)

  If you are using a controller real time you WILL LabVIEW Real-time.

  You can't function without it!

  Best regards

  Mencef

• Compact RIO NOR-9082 Configuration in MAX, cannot save

  Hello world

  I tried to implement a new cRIO the NOR-9082. Currently, I am able to see the cRIO under "Remote devices" in MAX configuration and view. However, the two errors that are produced:

  (1) when I try to change the setting as the host name and press 'save' a warning appears saying: "there was a problem, save the settings of the target. Make sure that your material is under tension and hat it is connected to the network. I have attached a picture below.

  (2) at the same time, when I try to install the software on the cRIO by double-clicking on 'software' and selecting "Add/Remove software" and run the Wizard "LabVIEW Real - Time Software", another error is displayed: "error: the disk hard n the remote system is complete or encountered an i/o error." I've also attached a picture below.

  The cRIO is lit with "DISABLE RT' toggled OFF. It is connected to the network via an Ethernet cable. This connection seems fine, however I look. (The connection of Ethernet port light flashes continuously activity indication etc..) It is the PC that is connected to the same network, I'm trying to interface with the cRIO. The cRIO displays the right IP address assigned through the network.

  My apologies if I have not provided enough information to solve this problem, but if someone might be able to explain why I could meet these two problems in these circumstances, assistance would be much appreciated. Thank you!

  It seems the main reason I got all these weird problems, it was because the compact RIO NI 9082 can come bundled with windows 7 and LabVIEW 2012 SP1 preinstalled and run as stand-alone computer so all I had to do was plug in a VGA to a screen and a mouse USB, keyboard and an eithernet for network connection cable and he started very well. Now, development and deployment happen locally on the cRIO. It was a little silly to me, so hope that helps someone!

  Kind regards

  Ago - Wei.

• New user of Lab-view and Compact RIO

  Hi I am new to Labview environment and cRIO. I have to design a CAN bus for electronic car. I've done a few tutorials on how to create a VI. If anyone knows where I'll start to be able to send and receive messages using CAN bus and Compact RIO in order to implement the actual data from sensors or actuators CAN message?

  Thank you

  Abdoulaye

  Start with the examples provided with LabVIEW.  To the title of the help, select «Find examples...» ».  When the finder example opens select 'hardware input and output-> Compact RIO-> Module e/s specific-> CAN' and try to start with the basic example of CAN.

• touchscreen compact Rio

  Hello world!

  I'm developing an application to control a cooler with Labview 2012 and Compact RIO. I would like to create a group of GUI to visualize data and a basic control.

  However, I would like to use a touchscreen to third party (not OR). Purchase the Labview Touch Panel module can I do?

  My question is: if it's just a screen and not a PC, simply by connecting to the RIO Compact RS232 port and launch of real-time application,

  It will allow me to control the VI?

  Thank you!

  I don't see why not.  You need to just make a protocol of good communications between your cRIO and computers touch screen.  I find a network stream to work very well.

• stand alone compact rio

  Hi to everyone!

  I am a student of the University and for my thesis, I use a COMPACT RIO with neither 9205 and gps module, some measures aboard an eletric car, measures will be saved to a TDMS file in the RIO COMPACT by a stand alone configuration and without connection to a pc.

  The compact rio will begins with the car and it will go off with him also.
  So I have a question, how can I stop the VI within the CRIO before turning off the car?  or in TDMS data will be saved in the same way without close the VI within the CRIO before turning off the car?

  Thank you

  Hello antoniolc!

  There is no way of knowing inside CompactRIO, if the system will be shut down.

  You must use an external signal to find out when your car will be stopped.

  Or you can use a multiple TDMS file and like it, just the last TDMS file will be unreadable. But you can probably read all previous TDMS files.

  Best regards.

• Selection of Module e/s analog compact RIO

  Hi everyone, sorry if this is the wrong place to post, I couldn't see any analog IO section in the hardware section.

  I'm looking to acquire an analogue of module e/s for a compact RIO, but there are a few options, and I was wondering if there was any kind of guide to help me to choose the most appropriate module?

  Dawud,

  This will depend on especially what entries you want to read, but you must keep the following in mind.

  How much time do I need to purchase samples?

  Degree of accuracy these samples should be?

  How many channels do I need?

  What voltage range I have to read?

  You can start on the following link and choose the options on the left to get to the bottom for a few modules.

  http://sine.NI.com/NP/app/main/p/AP/global/lang/en/PG/1/SN/N25:device, n24:cRIO.

• LabVIEW for 89410A pilot

  Hi all

  I'm looking for driver to LabVIEW for HP 89410

  I tried to pilot network and site manufacturer instruments

  Could you help me

  Concerning

  Christmas morning,

  Here is the link to the page of 89410 model has 3 drivers of different instruments for you to choose.  I recommend LabVIEW Plug - and - Play (project-style) driver instruments.

  See you soon,.

  NathanT

• Which macbook model is good for daily stock trading?

  Which macbook model is good for daily stock trading?

  None of them are suitable.

• HP Pavilion model 17-G192NR: downgrade HP Pavilion model 17-G192NR for Windows 7

  Is it possible to downgrade HP Pavilion model 17-G192NR of 10 of Windows to Windows 7 and maintain the touchscreen?

  Hi@ron_n_az,

  Welcome HP forums . The best place for all kinds of solutions, tips and settings for your questions/problems.

  For the best experience on HP forum, see our Guide to HP Forums to learn more.

  Decommissioning of the OS. Is this fair?

  I will definitely help you.

  HP has never tested model you PC for Windows 7.

  After that, it is very difficult to find drivers for all the internal hardware components on your PC from HP for Windows 7.

  Without a driver, most of the internal components will not work. It causes a lot of inconvenience to help you.

  But again, it is your choice of switching between the operating system that you have the PC.

  Hope that helps.

  Resolv_S

  Happy to help you. I work for HP
  
  Please click "Accept as Solution" if you feel my post solved your problem, it will help others find the solution.
  Click on ' Bravo Thumbs Up ' to say 'Thank you' to help!

• NTP synchronization drop Linux Compact RIO

  Hello

  I followed this method of synchronization with NTP (https://decibel.ni.com/content/docs/DOC-39178) and it works most of the time, but sometimes, I lost the NTP synchronization and crio are about 7 s forward. (I get the problem with a 9035 and a 9068).

  When synchronization is no longer works, Pei ntpq command responds "connection refused".

  Does anyone have an idea about the problem?

  Thank you

  Hello Jacques,.

  Sorry, I wasn't very clear

  Before you add the ntp-utils, I lost the synchronization several times: sometimes after a few days, once, after more than 2 weeks, but also sometimes on startup, I was not able to sync

  Given that I have install ntp utils, 10 days earlier, on 5 compact rio, I run the of-p command ntpq every minute and I always get a response, then that means I never lost the NTP synchronization (or I lost it less than a minute). I will continue to monitor them, but it seems that ntp-utils has helped me as weel

  Concerning

  Kevin

• LabVIEW for LEGO MINDSTORMS and EV3

  LabVIEW for LEGO MINDSTORMS can be used to program the EV3?

  There will be support for the EV3 with LabVIEW to come. Our plan is to be ready in the first half of 2014.

  MINDSTORMS EV3 of LEGO development environment is the only software I know that can be used to program the EV3 brick when it is made available for purchase.

• Connect the large number of parameters and variables between Verstand and model of Labview

  We have an installer of dyno with a chassis PXI-E running Veristand 2014 and 2014, inertia. In order to strengthen the capabilities and timing of the Veristand, I would use models of Labview to perform tasks is not possible by Veristand and inertia. An example of this is to determine the maximum amount of a large number of thermocouples. VeriStand has a comparison function, but it compares two values at once. This makes long and rigid emissions. LabVIEW, on the other hand, has a function which words one to get the maximum items in a table in one step. I need to use Labview to 'send' the thermocouples of 50 or more to the Labview model. In addition to the variables that must be communicated between Veristand and Labview, I also need to present Labview with the threshold and setting parameters. Forums and user manuaIs understand that you must use the connector pane in Labview Veristand System Explorer mapping to expose the inports and isolated villages. The problem is that the part of Labview connector is limited to 27 I/O. How to overcome this limitation?

  BTW. I'm relatively new to Labview and Versitand.

  Thank you.

  Richard

  You can work around this limitation by putting your orders and clusters indicators. Then set the cluster to be required or recommended to indicate whether contained controls are entered or parameters, just normal.