Compact RIO NOR-9082 Configuration in MAX, cannot save

Similar Questions

• Reading Configuration files using Labview RT in a Compact RIO

  Hello

  I am very new to Labview RT/Compact RIO development platform and happen to have a question. I will develop an application in Labview RT / FPGA that will make several simulations. However some these simulations can produce different results depending on the configuration settings. Our systems generally run in a Windows application, were there is a configuration (usually in XML format) file that the application reads and analyzes the given parameters. I was wondering if there is something similar, that I can do it, in which I have a configuration file that can be read before my Labview RT/FPGA application initialization, to change the simulation.

  Thank you

  Mario

  Hi Mario,.

  That's right, there are screws for the files .ini on real-time targets.

• connection of users and configuration of MAX

  I searched the site for 3 days and finally found a post titled; "IAK login user and configuration MAX" on 04/21/2009 who has asked pretty much the same problem, I'm going to. I wonder if there is something new on this subject because I need a solution.

  I installed an application and the NI FP driver suite see 6.0.11. I run NI MAX and open my. File IAK, which is located in the folder/common directory as well as the executable file of my application. At the beginning I used to hit the 'Save' selection but have found since that it makes no difference, so now, I'm not hitting 'Save', but just close MAX. This process is to record the location of my. IAK file somewhere, because after that my application runs and communicates very well with my e/s.

  The problem comes when I have the new station operators connect to the computer that controls the operation of my test. the application that auto starts because it is in the startup folder "All Users" cannot communicate with inputs and outputs.

  MAXIMUM running and opening the. IAK file under each new user login then immediately closing MAX solves the problem and all is well, and this process must occur the first time that a new user connects to the computer. The post mentioned above indicates that it is a normal behavior.

  The problem is that some of my operators do well to find the power button and turn on all the morning. The application is no "Exit", "Task Manager" should be used to stop it. Login information is stored on a post-it in their portfolio, and ask them to open MAX and save the configuration is just too much for them to do - be unfamiliar with the operation at first.

  Can someone explain to me how to fix this or refer me to a validated solution?

  Thank you

  OK - here it is:

  It works for me under Windows 7 with FP1000 e/s on a serial Comm. port other configurations may or may be not the same in these respects.

  While logged in as a privileged user configure you application to work and communicate with the e/s using an IAK file. Create the IAK via NI MAX.

  Is the key to register of interest here: [HKEY_CURRENT_USER\Software\National Instruments\FieldPoint Explorer\Recent File List]

  The string value is: "File1"="C:\ApplicationPath\IOConfigurationFile.IAK."

  Start the REGEDT32 Registry Editor. EXE and navigate to the key just below SOFTWARE that tells of National Instruments.

  Select the key, and then right-click on it. Select EXPORT, select a path and name of the output file.

  There will be many other entries, but this recent file one is the only one that may be necessary.

  You will end up with one. REG file with the specified name that contains the following elements:

  Windows Registry Editor Version 5.00

  [HKEY_CURRENT_USER\Software\National tools]

  [HKEY_CURRENT_USER\Software\National Instruments\FieldPoint Explorer]

  [HKEY_CURRENT_USER\Software\National Instruments\FieldPoint Explorer\Recent File List]
  'File1"="C:\\ApplicationPath\\IOConfigurationFile.iak '.

  Create a BAT file under the name of your choice. Configure.BAT for example.

  This BAT file will reside in the directory of your application with your Important file and it will contain 1 line.

  This:

  REG IMPORT "C:\ApplicationPath\ConfigurationRegistryExportFile.REG" > rejconfig.log

  Place a shortcut to it. BAT file in the 'All Users' Start menu.

  Any user who connects will receive this update of the registry which will allow the driver to IO to know how to communicate with your IO.

  Replace your appropriate to the ApplicationPath, IOConfigurationFile, ConfigurationRegistryExportFile, rejconfig.log file names. The log file will be written only for in the case of an error.

  Good luck

  Dfhotz

• stand alone compact rio

  Hi to everyone!

  I am a student of the University and for my thesis, I use a COMPACT RIO with neither 9205 and gps module, some measures aboard an eletric car, measures will be saved to a TDMS file in the RIO COMPACT by a stand alone configuration and without connection to a pc.

  The compact rio will begins with the car and it will go off with him also.
  So I have a question, how can I stop the VI within the CRIO before turning off the car?  or in TDMS data will be saved in the same way without close the VI within the CRIO before turning off the car?

  Thank you

  Hello antoniolc!

  There is no way of knowing inside CompactRIO, if the system will be shut down.

  You must use an external signal to find out when your car will be stopped.

  Or you can use a multiple TDMS file and like it, just the last TDMS file will be unreadable. But you can probably read all previous TDMS files.

  Best regards.

• NTP synchronization drop Linux Compact RIO

  Hello

  I followed this method of synchronization with NTP (https://decibel.ni.com/content/docs/DOC-39178) and it works most of the time, but sometimes, I lost the NTP synchronization and crio are about 7 s forward. (I get the problem with a 9035 and a 9068).

  When synchronization is no longer works, Pei ntpq command responds "connection refused".

  Does anyone have an idea about the problem?

  Thank you

  Hello Jacques,.

  Sorry, I wasn't very clear

  Before you add the ntp-utils, I lost the synchronization several times: sometimes after a few days, once, after more than 2 weeks, but also sometimes on startup, I was not able to sync

  Given that I have install ntp utils, 10 days earlier, on 5 compact rio, I run the of-p command ntpq every minute and I always get a response, then that means I never lost the NTP synchronization (or I lost it less than a minute). I will continue to monitor them, but it seems that ntp-utils has helped me as weel

  Concerning

  Kevin

• Support for alarms diagnosis field according to FF - 912 with NOR-FBUS Configurator 3.2.3

  I tried to control the utility alarm monitor and diagnosis field according to FF-912 alarms since a FF camera H1 with NOR-FBUS Configurator 3.2.3.

  Alarms standard block for example in the case of a change of parameter are monitored in the alarm monitor.

  Field diagnosis according to FF - 912 alarms are not controlled.

  Are field alarms diagnosis according to FF - 912 took supported by the NOR-FBUS 3.2.3 Configurator. or something special to do to activate the analysis.

  If not, what tools or host systems are available for monitoring these alarms?

  Alarm in the software OR-FBUS monitor doesn't have a field of diagnostics alarms. You can try to use NOR-FBUS C API nifWaitAlert2 to monitor this alarm. We will find the detailed description of the API OR FBUS Hardware and Software User Manual Chapter 6.

• touchscreen compact Rio

  Hello world!

  I'm developing an application to control a cooler with Labview 2012 and Compact RIO. I would like to create a group of GUI to visualize data and a basic control.

  However, I would like to use a touchscreen to third party (not OR). Purchase the Labview Touch Panel module can I do?

  My question is: if it's just a screen and not a PC, simply by connecting to the RIO Compact RS232 port and launch of real-time application,

  It will allow me to control the VI?

  Thank you!

  I don't see why not.  You need to just make a protocol of good communications between your cRIO and computers touch screen.  I find a network stream to work very well.

• Emular / Simular Compact RIO

  Hay alguna manera trabajar o hacer simulando Québec tengo el RIO Compact the tests? Ocupo hacer unas secuencias, pero aun no tengo el RIO Compact how.

  Yo as recuerdo con las Renault suckers hacer tus VI y poner una virtual DAQ, is you can hacer algo parecido? o para trabajar con screw in Compact RIO is space forzosamente tenerlo how?

  MUCHAS gracias! Era justo lo than amazed!

• Basis of LabVIEW Development with Compact RIO device software

  Hello.  Currently, I have the LabVIEW Base development software package and have been using it with DAQ Compact devices for the acquisition of basic data.  I would now like to start integrating controls in my system, changing to RIO Compact for deterministic real-time features.  My question is that I would be able to build applications for the Compact RIO system using only the basis of LabVIEW Development package without updating immediately?  Maybe some features are not available for me, but could at least get a good start like that?

  A CompactRIO embedded time real operating system (RTOS) called VxWorks you need to target the deployment of LabVIEW code to the device. Classic LabVIEW screws you will have been written so far are built to target general purpose operating systems (GPO) such as windows.

  To create screws that are deployable to STSOp, you will need the real-time Module that is not included in the basis of LabVIEW. As a result, to take advantage of the embedded FPGA, you'll need to install the LabVIEW FPGA Module as well.

  As long as you have the FPGA modules and in real time, it seems to me that you should be able to control these devices with LabVIEW Base. Without these software components you will not be able to create an instance of the device target your LabVIEW project.

• New user of Lab-view and Compact RIO

  Hi I am new to Labview environment and cRIO. I have to design a CAN bus for electronic car. I've done a few tutorials on how to create a VI. If anyone knows where I'll start to be able to send and receive messages using CAN bus and Compact RIO in order to implement the actual data from sensors or actuators CAN message?

  Thank you

  Abdoulaye

  Start with the examples provided with LabVIEW.  To the title of the help, select «Find examples...» ».  When the finder example opens select 'hardware input and output-> Compact RIO-> Module e/s specific-> CAN' and try to start with the basic example of CAN.

• Selection of Module e/s analog compact RIO

  Hi everyone, sorry if this is the wrong place to post, I couldn't see any analog IO section in the hardware section.

  I'm looking to acquire an analogue of module e/s for a compact RIO, but there are a few options, and I was wondering if there was any kind of guide to help me to choose the most appropriate module?

  Dawud,

  This will depend on especially what entries you want to read, but you must keep the following in mind.

  How much time do I need to purchase samples?

  Degree of accuracy these samples should be?

  How many channels do I need?

  What voltage range I have to read?

  You can start on the following link and choose the options on the left to get to the bottom for a few modules.

  http://sine.NI.com/NP/app/main/p/AP/global/lang/en/PG/1/SN/N25:device, n24:cRIO.

• HPDM 4.6 SP4 cannot save the files deploy subtask

  Recently, when you create a new task to deploy a file and try saving it I get:

  "Cannot save the subtask to deploy files.

  If I create another type of task it saves without problem. The only time where there is a problem, is if I am trying to add files to my task. If I try to add a file to an existing template, I get the unable to merge the error of the model.

  I have checked the permissions in the main repository, run the test, all come back fine. I even tried manually adding files to the repository and that's ok too. I can't find something as interesting in the newspaper. I should mention that we did a database migration recently, but I test all features and managed to save a task of deployment without problem.

  Try to get out of the individual tasks that contains files (in this case the msi Hotkey filter) I get the following:

  2015-07-03 14:08:21 [error code: 5260288] [Module: MasterController] [category: input/output disc] 2015-07-03 14:08:21 [error details]:.\SyncTask.cpp@91: failed to sync files. .\port_layer\ftpclient\fileclient.cpp@816: failed to get the data from the file. .\port_layer\file_io\filefuncs.cpp@86: failed to get the data from the file : D:\HPDM/Repository/Files/ToDeploy\Hotkey filtre.\port_layer\file_io\filefuncs.cpp@84: the system cannot find the specified file.

  In the masterrepository log:

  2015-07-03 15:14:28 ERROR could not remove the package: Test. \port_layer\ftpclient\fileclient.cpp@235: has no file stat, RemoteDir: / files/repository/ToDeploy, name: Test.
  .\port_layer\ftpclient\fileclient.cpp@390: could not get the file stat, RemoteFile:\\10.7.1.29\HPDM$/Repository/Files/ToDeploy.
  .\port_layer\ftpclient\ShareFolderClient.cpp@424: has no file stat data.
  .\port_layer\file_io\filefuncs.cpp@86: failed to get the data from the file : \\10.7.1.29\HPDM$/Repository/Files/ToDeploy\Test
  .\port_layer\file_io\filefuncs.cpp@84: the system cannot find the specified file.

  2015-07-06 09:11:44 CTaskReceiverThread::recvTask() of ERROR: unable to receive data from ssl server.
  2015-07-06 09:11:44 CTaskReceiverThread::recvTask ERROR failed. Returns the value-1.
  2015-07-06 09:12:10 sendReoprt() of ERROR: unable to send data to the server.
  2015-07-06 09:12:10 CReportSenderThread ERROR::recvTask(): could not receive data from ssl server.
  2015-07-06 09:12:10 ERROR CReportSenderThread::recvTask failed. return value = - 1

  10.7.1.29 refers to a repository of the child, I have about 30 repositories of the child.

  I have not changed any configuration, I don't really understand how this happened, I can't even create my first Contact rules, scheduled tasks or create new tasks/templates. We are in the midst of a large-scale deployment so that any help ASAP that would be most appreciated!

  Thank you

  Luke

  This has been resolved with the help of Chen_HPDM by e-mail.

  We changed the console.conf to:

  HPDM. NEWSPAPER. LEVEL = DEBUG

  (console.conf can be found in C:\ProgramData\Hewlett-Packard\HP device Manager\Console\conf)

  I ran the task to deploy the files again and had the following in the log:

  2015 07-09 09:43:41 [WT-EventQueue-0] DEBUG Console - Request (20201): add templates

  2015-07-09 09:43:42 [WT-EventQueue-0] DEBUG Console - [TimeSpan] (20201): Add models [true]: 86

  2015-07-09 09:43:42 [WT-EventQueue-0] TemplateManager DEBUG - processAddTemplate: OS = HPWE8_64, name = New Test, category = files and the registry, status = transfer and tip =

  2015 07-09 09:43:42 [WT-EventQueue-0] DEBUG Console - Request (20202): update of model

  2015-07-09 09:43:42 [WT-EventQueue-0] DEBUG Console - [TimeSpan] (20202): update model [true]: 142

  2015-07-09 09:43:42 [WT-EventQueue-0] INFO FileOpt - cannot delete file: C:\ProgramData\Application Data\HPDM_Temp\Repository\Files\ToDeploy\_Temp

  2015-07-09 09:43:42 [WT-EventQueue-0] INFO FileOpt - cannot delete file: C:\ProgramData\Application Data\HPDM_Temp\Repository\Files\ToDeploy

  2015-07-09 09:43:42 [WT-EventQueue-0] INFO FileOpt - cannot delete file: C:\ProgramData\Application Data\HPDM_Temp\Repository\Files

  2015-07-09 09:43:42 [WT-EventQueue-0] INFO FileOpt - cannot delete file: C:\ProgramData\Application Data\HPDM_Temp\Repository

  2015-07-09 09:43:42 [WT-EventQueue-0] INFO FileOpt - cannot delete file: C:\ProgramData\Application Data\HPDM_Temp

  2015-07-09 09:43:42 [WT-EventQueue-0] INFO FileOpt - cannot delete file: C:\ProgramData\Application Data\HPDM_Temp\Repository\Files\ToDeploy\_Temp

  2015-07-09 09:43:42 [WT-EventQueue-0] INFO FileOpt - cannot delete file: C:\ProgramData\Application Data\HPDM_Temp\Repository\Files\ToDeploy

  2015-07-09 09:43:42 [WT-EventQueue-0] INFO FileOpt - cannot delete file: C:\ProgramData\Application Data\HPDM_Temp\Repository\Files

  2015-07-09 09:43:42 [WT-EventQueue-0] INFO FileOpt - cannot delete file: C:\ProgramData\Application Data\HPDM_Temp\Repository

  2015-07-09 09:43:42 [WT-EventQueue-0] INFO FileOpt - cannot delete file: C:\ProgramData\Application Data\HPDM_Temp

  2015-07-09 09:43:45 [Thread-43] DEBUG MPFactory - Call TemplateMP.

  2015-07-09 09:43:45 [Thread-49] DEBUG TemplateManager - processAddTemplate: OS = HPWE8_64, name = New Test, category = files and the registry, status = transfer and tip =

  2015-07-09 09:43:45 [Thread-49] TemplateManager DEBUG - processUpdateTemplate OS = HPWE8_64, name = New Test, category = files and the registry, status = failure, tip =

  The Console could not delete a temporary file created previously called HPDM_Temp. I renamed the file and was able to create the task.

  I can't wait to find my question on the forums, and someone didn't post the solution so I hope this helps and thanks again Chen!

  Luke

• Cannot save the attachments

  Original title: RECORDING of the parts JOINED IN VISTA

  WE CANNOT SAVE THE ATTACHMENTS. DOWNLOAD THE MESSAGE ERROR SAVING ATTACHMENTS. CHECK DISK SPACE. FILE IS NOT EVEN 80KO. These are PDF files.

  Thank you

  JO

  Try to compact and repair the database with this tool.
   
  
  WMUtil
  http://www.oehelp.com/WMUtil/default.aspx
   
   
  If this does not help, what security program do you use? Norton & McAfee are known to cause this problem. Restart and turn off your security program. Open WinMail and see if the attachment opens in your PDF reader.
   
   
   

• Cannot save the file (OS6)

  UPDATE: just found out that documentToBlob is compatible with the OS5. How to do the same thing in OS6?

  http://www.BlackBerry.com/developers/docs/WebWorks/API/BlackBerry.utils.html#.documentToBlob

  I wrote an application several months ago, which works very well with the OS5. But it does not work with OS6. Here is a simple example of creating a file, the application needs to do:

  config. XML

  
      http://www.w3.org/ns/widgets"
          xmlns:rim="http://www.blackberry.com/ns/widgets"
          rim:header="RIM-Widget:rim/widget"
          version="1.0.0">
       File Test
      Testing file
       http://www.example.com/" rim:copyright="no copyright" email="[email protected]">Example
       
       
       
       
       
       
       
      
      
  
  

  test.html

  
  
      
      
      
  
  
      testing
  
  
  

  scripts/test.js

  function loadTest(){
      alert("start");
      var filePath = "file:///store/home/user/appTest.xml";
      var xmlString = "test_data";
      var parser = new DOMParser();
      var doc = parser.parseFromString(xmlString, "text/xml");
      try{
          var blobData = blackberry.utils.documentToBlob(doc);
          blackberry.io.file.saveFile(filePath, blobData);
          alert("file saved");
      } catch(e) {
          alert("unable to save file: "+e.message);
      }
      if(blackberry.io.file.exists(filePath))
          alert("file exists");
      else
          alert("file cannot be found");
      alert("end");
  }
  

  Output of Simulator OS6 (6.0.0.337):

  • Star
  • Cannot save the file: undefined
  • file cannot be raised
  • en

  No idea why it does not work

  I couldn't find a solution to this, nor could anyone help. I had to rewrite my application to store data in a database instead of an XML file.

• E1000PCI: cannot save peripheral e1000e.

  I used VMware vCenter Converter Standalone v. 5.5.3 build 2183569 to convert my physical, local, 8.1 Windows machine to a virtual machine. Work ends and there is a file .vmx and a few other files created can I load the virtual machine.

  When I turn on the machine, using vmware workstation 11.1.0 build-2496824, the screen flashes the vmware logo and leaves immediately the machine running do not.

  In the vmware log file, I see these messages immediately before the other messages that appear related to the abandonment of employment.

  VMX | I120: E1000PCI: cannot save the e1000e device.

  VMX | I120: E1000: could not start the e1000e of the PCI Ethernet card.

  VMX | I120: E1000: failed to init device 3.

  VMX | I120: Module DevicePowerOn market failed.

  Help?

  
  

  Hi lwolf123and welcome to the VMware communities!

  You may need to follow these instructions to work around a defect in the converter: Re: VMware opens and quickly closes a virtual machine

  Check if the configuration of your virtual machine file contains these four lines mentioned in this post.  If not, add them and see if your virtual machine can then turn on the power.

  --

  Darius