Module NI 9214 and cRIO, where is the example for the scan Mode

Similar Questions

• You try to run the scan mode and mode interface fpga at the same time is causing errors

  I'm reading a 9236 9237 and a 9215 with the scanning engine and read from two 9211 modules with the fpga. It's because I need to acquire to 200 Hz with the 9236 9237 9215 but maximum rate of the scan engine is limited by the slower module in the system, which in this case is the max of 15 hz the 9211.

  So to use both interfaces (scan engine and fpga), I followed the percisely given in this article for instructions.

  1. the project has created and added the peripheral crio using the interface of the scan engine.

  2. Add the target fpga and drag and drop the 9211 inside modules

  3. has created the fpga in interface file with and compiled with no error.

  4. interfaced with the file fpga at almost exactly the way the sample project of "getting started with 9211' by using the engine of analysis in the interface with the other modules.

  5. after the errors to discover that I created a VI that tests for just the portion 9211 code (called "thermocouple FPGA method Test.vi")

  The data returned by the interface fpga was nothing else than zeros on all channels, even if thermocouples were hooked on some of them. (all zeros as entries in the convert temperature vi gives-410, 6160 degrees F, if you happen to have the material to try this.)

  I get the following error from the open fpga vi reference:

  code error-61141
  "Thermocouple method Test.vi FPGA.
  Activities FPGA:
  
  Open FPGA interface reference.
  Reserved outside LabVIEW FPGA:  turns The RIO Scan Interface.  You must set the mode Interface FPGA chassis in order to unlock the FPGA. »
  

  It's extremely frustrating, because as I explained, I've been very attentive not only follow the instructions for concurrent fpga and analysis but also to model my VI by the example of VI, even if only for the moment, just to try to work things out.

  Any help would be appreciated as I need to fix this for the further development and I am somehow in a lack of time. I opened a support ticket (reference #7256226), but the app engineer had no time to answer.

  My system:

  cRIO-9014 controller RT with crio-9104 bottom of basket.

  LabVIEW 2009

  Latest drivers and peripheral software pc and rio (RIO scan 3.2 engine support june2009)

  rex1030 wrote:

  I'm reading a 9236 9237 and a 9215 with the scanning engine and read from two 9211 modules with the fpga. It's because I need to acquire to 200 Hz with the 9236 9237 9215 but maximum rate of the scan engine is limited by the slower module in the system, which in this case is the max of 15 hz the 9211.

  This should not be the case.  9211 data will not update with each sweep, but you should be able to run the scan faster than 15 Hz without problem.  Do you have specific issues with this?

  So to use both interfaces (scan engine and fpga), I followed the percisely given in this article for instructions.

  1. the project has created and added the peripheral crio using the interface of the scan engine.

  2. Add the target fpga and drag and drop the 9211 inside modules

  3. has created the fpga in interface file with and compiled with no error.

  4. interfaced with the file fpga at almost exactly the way the sample project of "getting started with 9211' by using the engine of analysis in the interface with the other modules.

  5. after the errors to discover that I created a VI that tests for just the portion 9211 code (called "thermocouple FPGA method Test.vi")

  You can try making sure that the chassis is set to mode Interface FPGA and the setting is deployed.  I wrote that article that you referenced says will select the deploy option later and not explicitly speak to deploy the chassis later.  Run a VI with a reference open FPGA vi not automatically deploy chassis settings if you need to do it explicitly.  Try the following steps.

  1. right click on the frame element and select Properties.  Make sure that the Interface FPGA option button is selected. \

  2. right click on the frame element and select deploy.

  3. repeat your VI.

  The data returned by the interface fpga was nothing else than zeros on all channels, even if thermocouples were hooked on some of them. (all zeros as entries in the convert temperature vi gives-410, 6160 degrees F, if you happen to have the material to try this.)

  I get the following error from the open fpga vi reference:

  code error-61141

  
  "Thermocouple method Test.vi FPGA.
  Activities FPGA:

  Open FPGA interface reference.
  Reserved for LabVIEW FPGA outside: The RIO Scan Interface is running. You must set the mode Interface FPGA chassis in order to unlock the FPGA. »

  The likely cause of this error is that the setting of the FPGA Interface on the chassis has not been deployed.  If the chassis is still Mode Scan fixed personality bitfile will be loaded on startup and the FPGA will be locked.

  It's extremely frustrating, because as I explained, I've been very attentive not only follow the instructions for concurrent fpga and analysis but also to model my VI by the example of VI, even if only for the moment, just to try to work things out.

  I'm sorry that you have had difficulties.  Assuming that I'm wrong about the source of your problem, it seems we have to update less than Ko to include the deployment step.

  Any help would be appreciated as I need to fix this for the further development and I am somehow in a lack of time. I opened a support ticket (reference #7256226), but the app engineer had no time to answer.

  My system:

  cRIO-9014 controller RT with crio-9104 bottom of basket.

  LabVIEW 2009

  Latest drivers and peripheral software pc and rio (RIO scan 3.2 engine support june2009)

• Satellite A300D PSAKCE and PSAHCE - where is the difference?

  I have Toshiba A300D PSAKCE model.
  I looked for a win7 drivers but there is no drivers for this model yet.
  When I checked the model PSAHCE for WIN7 drivers were available.

  I tried a PSAHCE model and each component is similar to the model PSAKCE.

  So my question is? Where is the difference and can I use win7 64 bit drivers of the PSAHCE model for my PSAKCE model.

  Thank you...

  If I compare the specifications for the two models of laptops, I see that they have different chipset and wireless network card, but other things must be identical.

• How long a battery Acer Aspire last and exactly where is the battery in the laptop

  My laptop is almost two years old, it is very slow, except when the battery is fully charged.  It does not take a charge for very long.  The battery is some thing that I can replace it myself, and if so where can I find in the fold?  Thank you

  The battery is any thing that I can replace it myself, and if so where can I find in the laptop?

  Yes, the replacement of the battery is very simple:

  You will find a #2 latch located at the bottom of the laptop. You insert an appropriate tool in the lock and slide to release the battery #1.

  

  This is a replacement battery for your laptop: link

• Where are the Solution Center shortcuts, and how to use the (Scans)

  A frustration more than Windows 8 to get more than

  I have attached my C3180 to my new Windows 8 machine and the software installed.  It is running, but I'm a bit lost in the use of the center of Solution that seems different from what I had on XP.

  1. the only way I could see to change the destination of a scan, has been to create a new shortcut with the destination I want to use.  Is this correct?

   

  2. now that I have a short cut, where is it? When I run a scan from the Solution Center, the analysis proceeds to the default destination, so it must use the default shortcut.

  Is it possible to use the start scanning on the home of the solution Center window and make the scan go to my choice of the destination folder?

  Quit smoking research

  I found how to use the solution Center in Windows 8 here.

• Where is the Advanced mode and basis in the planning of the 11.2.3.000

  Hello.. I remember they were there in 11.1.1.3.000

  Concerning

  Which is more (much less), he went in the ADF mode conversion in 11.1.2.2

  See you soon

  John

  http://John-Goodwin.blogspot.com/

• Using the scan Mode 9411 cRIO-9074

  Hello

  I use an entrance Module differential differential NI9411 under cRIO-9074 with scan Mode, but I noticed that some problems are present.

  My application needs two encoder and we choose two incremental encoders with 1024pulses/rev. I have configured the NI9411 quadrature Mode, so I can read the position and speed of the encoder. Each shaft turn at different speeds.

  One of them can turn 4.6 rad/s as a maximum speed, while the other hit it up to 402 rad/s. Then, the configuration of the module input filter is set to 1microsed, the time base speed 32768 microseconds and the disabled index mode. These values make for a correct reading? The cRIO scanning speed is set to 1ms.

  On the other hand, watching the tutorials or (http://zone.ni.com/devzone/eda/tut/p/id/7109), that the degree of rotation depends on the encoding type, what type of encoding is used in Scan Mode? X 4?

  Using System Manager OR distributed, one of the encoders to read impulses sometimes sporadic (up to 2 digits) Although the encoder is stopped. However, the other bed is always 0. It seems that the encoder is broken, isn´t it?

  Thanks in advance for your comments

  Hi Juancar,

  I think that the values are suitable. The issue of reading 0 is explained in this KB:

  http://digital.NI.com/public.nsf/allkb/C9088DFDF803CD8B862575F3007C40FD?OpenDocument

  In addition, according to this document:

  http://zone.NI.com/DevZone/CDA/tut/p/ID/7338

  decoding type must be set to X 4.

  I hope this helps! Suerte con ello.

  Jesus

• my email is spam and I can't stop and I run all the scans and nothing found

  my computer sends Email without my knowledge and it's MPI, I runn all my scans including essentionals and security tool removal microsoft maleware, but everyting says my computer is clean, what can I do and where do I go?

  You could try to disconnect your computer from the internet for a day or two and see if that stops spam.

  Adding another antivirus program without first uninstall your current antivirus is NOT recommended - antivirus problems tend to see many parts of other antivirus programs as quite similar to the virus that they should treat them as viruses.

  However, there is another class of programs called antispyware programs you can try.  Windows Defender is one of them, then you might want to try first.  Programs in this class rarely interfere with each other, so you can more safely than installed.

  Three other possibilities to check:

  1. a spammer could find your login information for your e-mail account and started sending the spam using your account, but without using your computer at all.  In this case, change the password on your email account is quite often, so try that.  Make sure your new password is near the maximum length of the mail server allows, to make very slow computer programs through all possible guesses what it might be.  Also, try to include all classes or the characters (often the lowercase letters, capital LETTERS, numbers, and special characters) to slow down such a program even more.  In this case, you will probably also need to communicate with the people who run this server to make sure they don't deactivate your account.

  2. a spammer may have found just your email address and started using it on the spam without sending it on the same e-mail server that you use.  In this case, you need the headers of some spam messages to do much.  Most header lines are not normally indicated when you look at the email; additional steps to show them depend strongly on what e-mail program you want to show them.

  3. If your computer allows remote access connections, the spammer may guessed your username and password for your computer.  In this case, a change of password, but on your computer instead, is probably necessary.  You can also search for remote connections and how to disable them in the help file for your computer.  Among e-mail programs have a folder "sent", then you can check the spam messages here.  Also, the spammer may have created an extra account on your computer until you find the complete list of accounts and check the folder "sent" for each account.on this list.

• Switch Cisco 2960/3560 = > recovery password and default settings with the button Mode

  Hi Experts,

  I have some confusion with the button Mode with cisco 2960/3560 switches.

  I read on many forums and articles, but where things are not clear.

  a place given 3 seconds and somewhere is given 7 or 10 seconds.

  Qus1), what is the exact time to press/hold Mode button to perform two following tasks:

  A. password recovery (according to my knowledge 3 sec) good or bad?

  Configuration of the switch (start + run) would be safe

  After the recovery of password? Yes or no

  B. factory default (according to my knowledge 10 dry) good or bad?

  I'm afraid, because if I press mode button more than 3 seconds, then

  It will delete any configuration of cisco switch. Yes or no

  Qus2) I want to recover the catalyst 2960/3560 switch password without

  Start/run configuration to lose. That is my main concern.

  Please tell me how to do this, what will be the time keeping Mode buttom

  in a few seconds?

  Qus3) which means this line

  "If the password recovery mechanism is disabled in switch

  then you will lose all the config.

  This sentence has been given on this forum url

  https://supportforums.Cisco.com/thread/140848

  KS

  Attach a terminal or PC with terminal emulation (for example, Hyper Terminal) port console switch.

  Use the following terminal settings:

  • Bits per second (baud): 9600

  • Data bits: 8

  • Parity: None

  • Stop bits: 1

  • Flow control: Xon/Xoff

  Note: For more information on the wiring and connection of a terminal to the console port, refer to connecting a Terminal to the Console Port of Catalyst switches.

  Unplug the power cable.

  The power switch and take it to the switch: command prompt:

  2900XL, 3500XL, 2940, 2950, 2960, 2970, 3550, 3560, and 3750 switches of the series, to do this:

  Press and hold the mode button located on the left side of the façade, while you reconnect the power cable from the switch.

  2960, 2970

  Release the Mode button when the SYSTEM LED flashes orange and then turns green. When you release the Mode button, the SYSTEM LED flashes green.

  3560, 3750

  Release the Mode button after about 15 seconds when the SYSTEM LED turns green. When you release the Mode button, the SYSTEM LED flashes green.

  The system was interrupted before the flash at the end file system initialization

  loading the operating system software:

  flash_init

  load_helper

  boot

  switch:

  Run the flash_init command.

  switch: flash_init Initializing Flash... flashfs[0]: 143 files, 4 directories flashfs[0]: 0 orphaned files, 0 orphaned directories flashfs[0]: Total bytes: 3612672 flashfs[0]: Bytes used: 2729472 flashfs[0]: Bytes available: 883200 flashfs[0]: flashfs fsck took 86 seconds ....done Initializing Flash. Boot Sector Filesystem (bs:) installed, fsid: 3 Parameter Block Filesystem (pb:) installed, fsid: 4 switch: !--- This output is from a 2900XL switch. Output from !--- other switches will vary slightly.

  Run the load_helper command.

  switch: load_helper switch:

  Question the dir flash: command.

  Note: Be sure to type a colon ":" after the dir flash.

  Appears in the file system of the switch:

  switch: dir flash: Directory of flash:/ 2    -rwx  1803357                  c3500xl-c3h2s-mz.120-5.WC7.bin !--- This is the current version of software. 4    -rwx  1131                     config.text !--- This is the configuration file. 5    -rwx  109                      info 6    -rwx  389                      env_vars 7    drwx  640                      html 18   -rwx  109                      info.ver 403968 bytes available (3208704 bytes used) switch: !--- This output is from a 3500XL switch. Output from !--- other switches will vary slightly.

  Type rename flash: flash: config.old config.text to rename the configuration file.

  switch: rename flash:config.text flash:config.old switch: !--- The config.text file contains the password !--- definition.

  Issue the boot command to boot the system.

  switch: boot Loading "flash:c3500xl-c3h2s-mz.120-5.WC7.bin"...############################### ################################################################################ ###################################################################### File "flash:c3500xl-c3h2s-mz.120-5.WC7.bin" uncompressed and installed, entry po int: 0x3000 executing... !--- Output suppressed. !--- This output is from a 3500XL switch. Output from other switches !--- will vary slightly.

  Enter "n" at the prompt to abort the initial configuration dialog box.

  --- System Configuration Dialog --- At any point you may enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'. Continue with configuration dialog? [yes/no]: n !--- Type "n" for no. Press RETURN to get started. !--- Press Return or Enter. Switch> !--- The Switch> prompt is displayed.

  At the switch prompt, type en to enter a mode.

  Switch>en Switch#

  Password recovery

  Type rename flash: config.old flash: config.text to rename the configuration file with its original name.

  Switch#rename flash:config.old flash:config.text Destination filename [config.text] !--- Press Return or Enter. Switch#

  Copy the configuration file in the memory.

  Switch#copy flash:config.text system:running-config Destination filename [running-config]? !--- Press Return or Enter. 1131 bytes copied in 0.760 secs Sw1#

  The configuration file is now reloaded.

  Replace the current passwords that you do not know. Choose a password with at least one capital letter, one number and one special character.

  Note: Replace passwords that are required. You must crush not all passwords listed.

  Sw1# conf t !--- To overwrite existing secret password Sw1(config)#enable secret !--- To overwrite existing enable password Sw1(config)#enable password !--- To overwrite existing vty password Sw1(config)#line vty 0 15 Sw1(config-line)#password Sw1(config-line)#login !--- To overwrite existing console password Sw1(config-line)#line con 0 Sw1(config-line)#password 

  Write the running configuration in the configuration file with the write memory command.

  Sw1#write memory Building configuration... [OK] Sw1#

  For factory reset:

  do not give under the control of factory reset

  Switch#copy flash:config.text system:running-config

  can I copy the running configuration to Flash

  Switch flash running-config #copy:

  Destination file name [running-config]?

  Building configuration...

  [OK]

  Switch #copy running-config startup-config

  Name of destination file [startup-config]?

  Building configuration...

  [OK]

  Review the link for more information below

  http://www.Cisco.com/en/us/products/hw/switches/ps628/products_password_recovery09186a0080094184.shtml

  Please note the useful messages.

  Concerning
  Vesta
  "Everybody is genius." But if you judge a fish by its ability to climb on a tree, he will live his entire life, believing that this is stupid. "

• VMs and vswitches shared using the "Promiscuous" mode

  We are in the middle of setting up our new VM environment and you want to include Symantec Web Gateway virtual appliance. Must the vswitches (vNIC) use promiscuous mode. The problem is that all of my physical network cards are distributed between 4 virtual switches. No other virtual machines require promiscuous mode. When you set this mode on a vswitch, how will this affect the other virtual machines using the same switch? "Promiscuous" mode can be set on the switch and only ebabled to the virtual machine?

  I'm under esxi 5 and 8 network adapters in the servers of my host. There are 4 configured vswitches, one for management, data traffic, one for vmotion traffic and one for our DMZ.

  Thanks in advance

  You can create a separate virtual machine for this virtual machine port group and set security for the virtual machine portgroup activating the mode of promiscous-only activate the promiscous for virtual machines will be connected to the VM Port Group

• LaserJet 3020 (also known as the Prod. N ° Q2665A) - where is the scanning software?

  Hello

  I have a LaserJet 3020 (also known as the Prod. N ° Q2665A), with which I would like to scan, when you use a machine Windows 8.1 (64-bit).

  When I go to the HP support page, any downloadable software seems to be on the digitization, it is all about hologram.

  Am I missing something?  Can scan you with the software available on this HP support page?

  Here is a link to the support page to which I refer:

  http://h20566.www2.HP.com/portal/site/hpsc/template.page/public/PSI/swdHome/?sp4ts.Oid=378054&spf_p...

  Thank you!

  Hi JTK,.

  The LaserJet 3020 uses scanning software is integrated in Windows 8. I guess the same is true for win 8.1. This page describes how to analyze with the scanning of Windows software:

  Use the software in Windows 8 to analyze

  I hope this helps.

• How to retrieve the details of scaling of the cRIO channels, running in the Scan Mode.

  On the side of Windows, this can be done by reading the project folder and lifting some ProjectItem Properties at the Variable level. But how to get the information of scaling to a given variable, programmatically, the target of cRIO? THX.

  Look at the file variables.xml on the controller for cRIO to ftp: / //ni-rt/config/variables.xml

  It is not the cleanest way to get it, but it has the information you're looking for.

  Kurt

• Updates to Windows for the malicious software removal tool. Can I watch it install and then look at the scan

  Updates Windows 7 for malicious software removal tool. When the download of the update can I watch it install and then watching the ongoing comprehensive analysis

  Thank you for Pingu70

• The FTP.EXE program included in Windows 7 and Server 2008 help the PASV Mode connection

  What is the FTP.EXE program included in Windows 7 and Server 2008 helps to connect in PASV Mode?

  I ask because I had a strange experience with her. First, I will mention that I did hours of research and found many articles stating that it does not work in XP/2000/Server 2003, but I found nothing for Windows 7 or Server 2008.

  I found some people who kept him at work and others who could not. I tried with Windows Firewall turned off and will be on and firewall rules created. Others said it is not supported and that I should use a third-party FTP client. I could make it work in Internet Explorer and Windows Explorer. I am well aware of the situation these options in Internet Explorer.

  Here are the best real, I could run from the command line on my PC Windows 7 (32 bit), but not on Server 2008 64 bit.

  Now, before someone comes and asks me to check the firewall, I want to mention that I tried more than five clients of third-party FTP Server 2008 and they all worked perfectly. In addition, from the same Server 2008 it worked fine in IE and explore.

  On Windows Server 2008:

  FTP client blocked on: 150 opening data of channel for the directory list.

  Windows 7:

  C:\Users\wxk1>Systeminfo | b/findstr/c: "Name of the OS" / c: "Version of the OS.
  Name of the operating system: Microsoft Windows 7 Enterprise
  OS version: 6.1.7601 Service Pack 1 Build 7601

  C:\Users\wxk1>FTP ftp.secureftp - test.com
  Connected to ftp.secureftp - test.com.
  220 - FileZilla Server version 0.9.39 beta
  220 - Written by Tim Kosse (* address email is removed from the privacy *)
  220, please visit http://sourceforge.net/projects/filezilla/
  User (ftp.secureftp - test.com:(none)): test)
  331 password required for test
  Password:
  230 logged on
  FTP > dir
  200 port command successful
  Data channel opening 150 to the directory list.
  -r - r - r - 1 ftp ftp bookstore.xml 1471 25 June 2007
  -r - r - r - 1 ftp ftp 279658 25 June 2007 hamlet.xml
  -r - r - r - 1 ftp ftp 80641 25 June 2007 hamlet.zip
  -r - r - r - 1 ftp ftp 2164 japanese.xml 25 June 2007
  -r - r - r - 1 ftp ftp 0 July 3, 2007 the new text Document .txt (2)
  -r - r - r - 1 ftp ftp 0 3 July 2007 new document texte.txt
  -r - r - r - 1 ftp ftp 4677 25 June 2007 nutrition.xml
  -r - r - r - 1 ftp ftp 8463 pigs.xml 25 June 2007
  -r - r - r - 1 ftp ftp 7581 25 June 2007 plants.xml
  drwxr-xr-x 1 ftp ftp 0 subdir1 June 25, 2007
  drwxr-xr-x 1 ftp ftp 0 subdir2 June 25, 2007
  226 transfer OK
  FTP: 697 bytes received in 0.01Seconds 46.47Kbytes / s.
  FTP >

  Also, I do not install a server FTP PASV will be IIS 7 or anthing like that, just try to connect to a server FTP PASV. Here is the test server that I used:

  http://www.SecureFTP-test.com/

  Type	FileZilla
  Address	FTP.SecureFTP - test.com
  Opening of session	test
  Password	test

  Details on using

  Chilkat provides this FTPS test account for all those wishing to test the secure FTP client functionality. You can connect to ftp.secureftp - test.com, connect as a 'test' with password 'test' and download that all files present on the server. The "test" account can also retrieve entries in the directory. There is, however, no downloading files on the server.

  Hello

  The question you posted would be better suited to the Technet community. Check out the link and ask the question.

  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

• RAC ASM database and system files in the standby mode

  I have a database of ASM the knot two of the CARS and want to create a physical file system standby active database. This is supported by oracle? and you can share tips? Thank you

  I hope that's what you're looking for... See the below links

  http://pythianpang.WordPress.com/2009/07/07/Data-Guard-ASM-primary-to-filesystem-physical-standby-using-RMAN-duplicate/
  http://indiandba.blogspot.com/2011/03/create-physical-standby-on-normal-file.html

  Kind regards
  http://www.oracleracexpert.com
  RMAN Oracle 11 g new features
  http://www.oracleracexpert.com/2011/12/Oracle-recovery-managerrman-new.html
  Understand the Oracle RMAN Reporting
  http://www.oracleracexpert.com/2011/06/understand-Oracle-RMAN-reporting.html