Multiple site access to site + remote
Is it possible to have multiple connections VPN site-to-site-established headquarters of branches and allow remote users connect with Cisco VPN client at the same time to the router in a branch? I have the Cisco 800 series routers (892) in the main office.
Thanks for any suggestions, link...
Jernej Hello,
If you have a router c8xx in the branch, then the scenario you described
is possible.
See an example here:
Configuration of an IPsec router dynamic LAN-to-LAN by peers and Clients VPN
http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a00801dddbb.shtml
Basically, you can define multiple entries in a card encryption, both for LAN to LAN and remote access.
BR
-istvan
Tags: Cisco Security
Similar Questions
-
ASA Site, Remote Site cannot access DMZ to the Hub site
So I've been scratching my head and I just can't visualize what I what and how I want to do.
Here is the overview of my network:
Headquarters: ASA 5505
Site1: ASA 5505
Site2: ASA 5505
Training3: ASA 5505
All Sites are connected L2L to the location of the Headquarters with VPN Site to Site.
Since the HQ site I can ping each location by satellite, and each satellite location I can ping the HQ site. I will also mention that all other traffic is also correctly.
Here's my number: HQ site, I have a DMZ set up with a web/mail server. This mail/web server is accessible from my HQ LAN, but not from the satellite location. I need allow that.
What should I do?
My second question is that I want for satellite sites to see networks of eachother. I should create a VPN network between sites, or can this be solved in the same way that the question of the DMZ?
I enclose the show run from my ASA HQ
See the race HQ ASA
For the mail/web server that requires access on the remote site VPN tunnels, you must add the servers to the acl crypto, similar to the way you have it for network access. Make sure that both parties have the ACL in mirror. If you're natting from the DMZ to the outside, make sure you create an exemption from nat from the dmz to the outside for VPN traffic.
For the second question, because you have only three sites, I would recommend creating a tunnel from site to site between two satellite sites.
HTH
PS. If you found this post useful, please note it.
-
A tab open, when I click on a bookmark, the browser IS NOT open it in a new tab. It open in the same tab, replacing the old site.
In FEATURES it says:
«Browse multiple sites at once, simply and easily.» Each new site appears as a new tab.
I wish it would.
Install one or both of these modules.
- https://addons.Mozilla.org/en-us/Firefox/addon/open-link-in-new-tab/
- https://addons.Mozilla.org/en-us/Firefox/addon/open-bookmarks-in-new-tab/
In addition, see How to set the home page which explains how to open several sites such as your homepage.
-
How to index a table on multiple sites?
Hello
How to index a table on multiple sites?
I searched this issue and was not able to find the answer. I understand that it can be done with loops, but I don't know how.
I use the detector of crete vi for frequency domain data collected a VNA (s2p) file. The products contain a table of amplitudes and a table of locations. The problem is that the locations refer to the index of table of amplitude, which is not the same as the frequency. My idea is that I can use this output of the places table to index the frequency to the detected peak frequencies table and then draw these, as well as some analysis data and manipulation on them. Currently, I can do this only by consulting table on the front panel.
The entrance to the peak detector is currently a table 1 d of the scale (what is the problem?).
I also looked at the supply frequency & estimate VI, but this VI seems only exit of scalar data for the largest peak, not exactly what I'm looking for.
Thanks for your help.
You have a second table for the tested frequency? If so, then you are right that you just need to index this table with the indexes by the Ridge detector. Use a loop for. Automatic index to the index, use index in array to get the value of the frequency and autoindex on frequencies.
-
You can host multiple sites on a single account webBasic?
You can host multiple sites on a single account webBasic?
Hello
Basically not how it has been intended for.
You have the option to have a partner account that you can create different sites in your portal where each site will be under its own plan.
Or you have an existing account that is designed for a single site. So I wouldn't say that, but ideally, you could add several domains under a plan account to a site, but you will then need to share the same account (a store of sense, a set of system messages, layout, etc.).
These are the options at this point.
I hope this helps!
-Sidney
-
Multiple sites using the same instance of CF?
Hi Gang-
I have a client who has recently improved CF Pro to Enterprise and they use in a relatively simple way as an intranet. They would like to help me configure a second instance for the purpose of a staging server, but I noticed after they revealed they do not have the link of Enterprise Manager in their CF Admin screen.
They need to reinstall CF using the MultiServer installation version to be able to deploy a second instance of CF? Need to uninstall and reinstall? Ugh...
Can't they just create a second site under their web server, using a different port and you worry about the second instance of CF? Best practices for a moment, remember, they do not necessarily expand on this server, it is intended to be a staging server.
Any ideas on the best and fastest way to handle this?
Many thanks in advance,
RichMany questions, many answers. :-)
Yes, rich, they would need to install the version multiserver for you to see this Enterprise Manager option in the CF Admin. But no, they would not need to uninstall the server deployment (what you did) to add to the MultiServer deployment. They can coexist (although it is not something most would do in general).
The best news for you is that, Yes, they can indeed just set up a second site on their web server, and who also point to the deployment server CF one you have installed. It is, of course, assuming that they are running a web server that supports multiple sites. If it's Apache, you're good. If this is Windows, then as long as the Windows Server 2003 (or 2008 or Vista), you're good, too. (Just to be complete, for other readers, XP does not allow you run multiple sites at the same time.)
If during the installation of the CF tells you that there all sites on the web server with CF, you need do nothing again create site. It should be immediately able to run pages CF. If you said that it is in CF link to a site, then you will need run the server web Configurator again. You can do it manually, even after installation. See the CF Admin and Config docs to learn more about it, as well as on this issue. (I know many like to just run things and hope that the interface is pretty clear, but as this issue shows, for some things anyone installing CF will be well served by looking at this collection of Miss often.)
Hope that helps, Rich. It is not a RTFM response. :-) Suffice it to say that if you need more that what I said, it's in the manual. Yet, I am happy to answer follow up if I can.
-
someone was able to access my laptop remotely today, how would I know if they let any virus or spyware on it. I have norton 360 virus protection that has not detected any viruses. IM worried about using my computer to stuff order online where they can steal my credit card details / number while im using it
Hello
How do you know that someone will access your computer from outside? Allow access and do you
you know who it was?Here is some information that should help you:
Was it a SCAM phone call that initiated the connection distance:
Avoid scams to phone for tech support
http://www.Microsoft.com/security/online-privacy/avoid-phone-scams.aspxIts a total scam. Uninstall their software and then perform a system restore before you install.
Change all your sensitive passwords at all sites - e-mail, Bank, credit cards and others. (Do not
on the computer compromise and it would be better to do it on the phone or in person.)You can even restore your system to factory fresh to make sure their software violates not
your security. (Ways to re - install Windows Clean - removing everything on the backup drive so all the data
before hand.)It is also possible that they consulted Bank, passwords and information of credit card on your computer. If
in order to check for malicious software as shown below. Change your passwords. Contact the Bank and credit
phone card companies. Do the same for any investment or other sensitive professionals or personal
accounts that may have been violated.====================================================================
====================================================================In the United States, you can contact the FBI, Attorney general, the police authorities and consumer
Watch groups. Arm yourself with knowledge.No, Microsoft wouldn't you not solicited. Or they would know if errors exist on your
computer. So that's the fraud or scams to get your money or worse to steal your identity.Do not fall for the fake phone Tech Support
http://blogs.msdn.com/b/securitytipstalk/archive/2010/03/09/Don-t-fall-for-phony-phone-tech-support.aspxAvoid scams that use the Microsoft name fraudulently - Microsoft is not unsolicited
phone calls to help you fix your computer
http://www.Microsoft.com/protect/fraud/phishing/msName.aspxScams and hoaxes
http://support.Microsoft.com/contactus/cu_sc_virsec_master?ws=support#tab3Microsoft Support Center consumer
https://consumersecuritysupport.Microsoft.com/default.aspx?altbrand=true&SD=GN&ln=en-us&St=1&wfxredirect=1&gssnb=1Microsoft technical support
http://support.Microsoft.com/contactus/?ws=support#TAB0Microsoft - contact technical support
http://Windows.Microsoft.com/en-us/Windows/help/contact-support===========================================================
===========================================================Follow these steps carefully:
If you need search malware here's my recommendations - they will allow you to
scrutiny and the withdrawal without ending up with a load of spyware programs running
resident who can cause as many questions as the malware and may be more difficult to detect as the
cause.No one program cannot be used to detect and remove any malware. Added that often easy
to detect malicious software often comes with a much harder to detect and remove the payload. Then
its best to be thorough than paying the high price later now too. Check with them to one
extreme overkill point and then run the cleaning only when you are sure that the system is clean.It can be made repeatedly in Mode safe - F8 tap that you start, however, you must also run
the regular windows when you can.TDSSKiller.exe. - Download the desktop - so go ahead and right-click on it - RUN AS ADMIN
It will display all the infections in the report after you run - if it will not run changed the name of
TDSSKiller.exe to tdsskiller.com. If she finds something or not does not mean that you should not
check with the other methods below.
http://support.Kaspersky.com/viruses/solutions?QID=208280684Download malwarebytes and scan with it, run MRT and add Prevx to be sure that he is gone.
(If Rootkits run UnHackMe)Download - SAVE - go to where you put it-right on - click RUN AS ADMIN
Malwarebytes - free
http://www.Malwarebytes.org/products/malwarebytes_freeSuperAntiSpyware Portable Scanner - free
http://www.SUPERAntiSpyware.com/portablescanner.HTML?tag=SAS_HOMEPAGERun the malware removal tool from Microsoft
Start - type in the search box-> find MRT top - right on - click RUN AS ADMIN.
You should get this tool and its updates via Windows updates - if necessary, you can
Download it here.Download - SAVE - go to where you put it-right on - click RUN AS ADMIN
(Then run MRT as shown above.)Microsoft Malicious - 32-bit removal tool
http://www.Microsoft.com/downloads/details.aspx?FamilyId=AD724AE0-E72D-4F54-9AB3-75B8EB148356&displaylang=enMicrosoft Malicious removal tool - 64 bit
http://www.Microsoft.com/downloads/details.aspx?FamilyId=585D2BDE-367F-495e-94E7-6349F4EFFC74&displaylang=enalso install Prevx to be sure that it is all gone.
Download - SAVE - go to where you put it-right on - click RUN AS ADMIN
Prevx - Home - free - small, fast, exceptional CLOUD protection, working with others
security programs. It is a single scanner, VERY EFFICIENT, if it finds something to come back
here or use Google to see how to remove.
http://www.prevx.com/ <-->-->
http://info.prevx.com/downloadcsi.asp <-->-->Choice of PCmag editor - Prevx-
http://www.PCMag.com/Article2/0, 2817,2346862,00.aspTry the demo version of Hitman Pro:
Hitman Pro is a second scanner reviews, designed to save your computer from malicious software
(viruses, Trojans, rootkits, etc.). who infected your computer despite safe
what you have done (such as antivirus, firewall, etc.).
http://www.SurfRight.nl/en/hitmanpro--------------------------------------------------------
If necessary here are some free online scanners to help the
http://www.eset.com/onlinescan/
-----------------------------------
Original version is now replaced by the Microsoft Safety Scanner
http://OneCare.live.com/site/en-us/default.htmMicrosoft safety scanner
http://www.Microsoft.com/security/scanner/en-us/default.aspx----------------------------------
http://www.Kaspersky.com/virusscanner
Other tests free online
http://www.Google.com/search?hl=en&source=HP&q=antivirus+free+online+scan&AQ=f&OQ=&AQI=G1--------------------------------------------------------
After the removal of malicious programs:
Also follow these steps for the General corruption of cleaning and repair/replace damaged/missing
system files.Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN
Enter this at the command prompt - sfc/scannow
How to fix the system files of Windows 7 with the System File Checker
http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.htmlHow to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
How to run check disk in Windows 7
http://www.SevenForums.com/tutorials/433-disk-check.html-----------------------------------------------------------------------
If we find Rootkits use this thread and other suggestions. (Run UnHackMe)
======================================
If necessary AFTER THAT you are sure that the machine is clean of any malware.
How to do a repair of trouble Windows 7 installation (it's for Windows 7 and there are similar procedures
for Vista if necessary.)
http://www.SevenForums.com/tutorials/3413-repair-install.htmlI hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="">-><- mark="" twain="" said="" it="">->
-
publication order, config to access local server remote-web
Al hilo mi otro post http://forums.ni.com/t5/LabVIEW/sin-acceso-a-control-remoto-web-publishing/m-p/1497856/highlight/tru... are solved, tengo otro problemilla:
I have a server local integrated con varios hence donde to banish una scada application runs. Can not get access a control remote, any red ordenador desde (tras varios question fallidos, to consiguio asignandole has the IPv4 cada red useful, the fija del servidor DNS config).
Well, then be brought desde una conexion externa, claro, pero no con fija the DNS no access or internet tengo acceso al servidor, por direccion http... remote web-publising created por the tool tool. Aunque seguimos investigando, local administrator el y yo creo as cerca, pero momento estamos no hemos dado con the respond.
What creeis can faltar a mi config, tanto local como labview_v8.5 del servidor del?
MUCHAS gracias Jorge, por information.
Todo lo Québec is explica in el link are be habia probado una u otra forma.
The main problem, I think that is what el servidor is una IP fija, puesto that companies should pay al proovedor telephone what wear ahora esta mas. Además, de dejar el servidor por temas seguridad tal y como esta.
Logicamente no mi depende, pero to thanks the ayuda.
No however, TR alguna alternativa en funcion of lo conoces what ha en el Haddad post, comentalo.
Saludos.
-
I have a similar computer is trying to access e-mail remotely, but can't get "display only". I tried to set up the computer, I try to access, by typing gpedit.msc, and it comes with a screen that says the file cannot be found. I then went to the BASE of KNOWLEDGE AND HE has TOLD ME to FOLLOW THESE INSTRUCTIONS
- Click Startand then click run.
- In the Open box, type mmc, and then click OK.
- On the file menu, click on Add/Remove a snap.
- Click on Add.
- Under available stand-alone snap-ins, click Group Policy, and then click Add.
- If you do not want to edit the Local computer policy, click Browse to locate the Group Policy object you want. Supply your user name and password if prompted, and then when you return to the Select Group Policy object dialog box, click Finish.
But at step 5 when he said, under -ins autonomous available, click Group Policy, THERE has BEEN NO GROUP POLICY click
So that you can see, I'm at square one. I went to this problem 12 hours over a period of 3 days.
I wish you help!
See my response to your thread in the other forum in which you've posted. There is no need to post to several forums; It's just more work for people who are trying to help you. If you need additional assistance, please post in the other thread.
http://social.answers.Microsoft.com/forums/en-us/xpprograms/thread/9910d218-7fb6-4821-8986-d2648a247dfc MS - MVP - Elephant Boy computers - don't panic!
-
Restrict access to the remote computer of single machine or the single IP address.
Hello
I have a server on which I want to prevent users from remote session. All I want is to give access to a user or machine or IP and that this machine/user/IP can access the server remotely.I tried the below mentioned step and it does not work for me, maybe I'm missing something.Control Panel > administrative tools > Windows Firewall with advanced security > inbound rules > Remote Desktop (TCP-In) and I tried every tab scope, users, computers, I am still able to access the server of any filling machine.Please suggest is possible I can prevent the other users, I can't create a new user account, I have to share the password what I can do is limited to the single machine/user/Ip address.Please suggest.Concerning
Yoann kassoum COULIBALYHi, VC.
I advise you to post this question in the Windows 7 IT PRO Forum /Networking. This community will be able to find solutions to your problems.
B Eddie
-
Cannot access the Console remotely
Hey guys, I'm new to VM Ware and has difficulties to access the console remotely, even if I can access the Web Access page very well...
The error I get is:
Unable to connect to the MKS: unable to connect to the host domain.com: no connection could be made because the target machine actively refused
When you search for an answer to this, I found a post that said to ensure that the /etc/pam.d/vmware-authd has been configured correctly, as well as the/etc/vmware/config...
None of these files/folders are there.
That said, my host OS is (unfortunately) of Windows Vista, with VM Ware running on top of that, and now I am trying to get Fedora Core 11 to present itself as the virtual machine.
Any ideas you can give would be much appreciated.
Sorry, I did not myself clear - its port 902 on the host that you need to check that you can telnet to because the VMware console connections are made using the host (so that they can still operate even when there is no network in the comments, for example at installation time), not to the guest directly (for client firewalls are not the parameters used either for the console). I guess that 8333 is fine, otherwise you wouldn't be able to connect remotely to the web console.
Guy Leech
VMware vExpert 2009
---
If you have found this device or any other answer useful please consider the use of buttons useful or Correct to award points.
-
Hello
I'm trying to solve a problem with the VPN, and I hope that someone could give me a helping hand.
We have 3 offices, each with an ASA 5505 like the router/firewall, connected to a cable modem
(NC Office) <----IPSEC----->(office of PA) <----IPSEC----->(TC Office)
Internally, we have a full mesh VPN, so all offices can talk to each other directly.
I have people at home, by using remote access VPN into the Office of PA, and I need them to be able to connect to two other offices there.
I was able to run for the Office of CT, but I can't seem to work for the Office of the NC. (I want to say is, users can remote access VPN in the PA Office and access resources in the offices of the PA and CT, but they can't get the Office of NC).
Someone could take a look at these 2 configs and let me know if I'm missing something? I am newer to this, so some of these configs do not have better naming conventions, but I'm getting there
PA OFFICE
Output of the command: "show run".
: Saved
:
ASA Version 8.2 (5)
!
hostname WayneASAnames of
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.1.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP 70.91.18.205 255.255.255.252
!
passive FTP mode
clock timezone IS - 5
clock to summer time EDT recurring
DNS lookup field inside
DNS domain-lookup outside
DNS server-group DefaultDNS
75.75.75.75 server name
75.75.76.76 server name
domain 3gtms.com
permit same-security-traffic intra-interface
object-group Protocol TCPUDP
object-protocol udp
object-tcp protocol
inside_access_in of access allowed any ip an extended list
IPSec_Access to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.2.0 255.255.255.0
IPSec_Access to access extended list ip 192.168.10.0 allow 255.255.255.224 192.168.2.0 255.255.255.0
IPSec_Access to access extended list ip 192.168.10.0 allow 255.255.255.224 192.168.5.0 255.255.255.0
inside_nat0 to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.10.0 255.255.255.224
inside_nat0 to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.2.0 255.255.255.0
inside_nat0 to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.5.0 255.255.255.0
TunnelSplit1 list standard access allowed 192.168.10.0 255.255.255.224
TunnelSplit1 list standard access allowed 192.168.1.0 255.255.255.0
outside_1_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.2.0 255.255.255.0
outside_2_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.5.0 255.255.255.0
outside_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.5.0 255.255.255.0
RemoteTunnel_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0
RemoteTunnel_splitTunnelAcl_1 list standard access allowed 192.168.1.0 255.255.255.0
RemoteTunnel_splitTunnelAcl_1 list standard access allowed 192.168.2.0 255.255.255.0
RemoteTunnel_splitTunnelAcl_1 list standard access allowed 192.168.5.0 255.255.255.0
out_access_in list extended access udp allowed any SIP host 70.91.18.205 EQ
out_access_in list extended access permit tcp any host 70.91.18.205 eq 5000
out_access_in list extended access permits any udp host 70.91.18.205 range 9000-9049
out_access_in list extended access permit tcp any host 70.91.18.205 EQ SIP
out_access_in list extended access allowed object-group TCPUDP any host 70.91.18.205 eq 5090
out_access_in list extended access permit udp any host 70.91.18.205 eq 5000
Note to outside-nat0 access-list NAT0 for VPNPool to Remote Sites
outside-nat0 extended ip 192.168.10.0 access list allow 255.255.255.224 192.168.2.0 255.255.255.0
outside-nat0 extended ip 192.168.10.0 access list allow 255.255.255.224 192.168.5.0 255.255.255.0
pager lines 24
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU----IPSEC----->----IPSEC----->
IP mask 255.255.255.224 local pool VPNPool 192.168.10.1 - 192.168.10.30
no failover
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0
NAT (inside) 1 0.0.0.0 0.0.0.0
NAT (outside) 0-list of access outside-nat0
inside_access_in access to the interface inside group
Access-group out_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 70.91.18.206 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
Enable http server
http 0.0.0.0 0.0.0.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set esp-3des esp-md5-hmac VPNTransformSet
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
card crypto IPSec_map 1 corresponds to the address IPSec_Access
card crypto IPSec_map 1 set peer 50.199.234.229
card crypto IPSec_map 1 the transform-set VPNTransformSet value
card crypto IPSec_map 2 corresponds to the address outside_2_cryptomap
card crypto IPSec_map 2 set pfs Group1
card crypto IPSec_map 2 set peer 98.101.139.210
card crypto IPSec_map 2 the transform-set VPNTransformSet value
card crypto IPSec_map 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
IPSec_map interface card crypto outside
card crypto outside_map 1 match address outside_1_cryptomap
peer set card crypto outside_map 1 50.199.234.229
crypto ISAKMP allow outside
crypto ISAKMP policy 1
preshared authentication
3des encryption
sha hash
Group 2
life 43200
Telnet 192.168.1.0 255.255.255.0 inside
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 inside
SSH timeout 60
Console timeout 0
management-access inside
dhcpd outside auto_config
!
dhcpd address 192.168.1.100 - 192.168.1.199 inside
dhcpd dns 75.75.75.75 75.75.76.76 interface inside
dhcpd allow inside
!a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal RemoteTunnel group strategy
attributes of Group Policy RemoteTunnel
value of server DNS 75.75.75.75 75.75.76.76
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list RemoteTunnel_splitTunnelAcl_1
dfavier vUA99P1dT3fvnDZy encrypted password username
username dfavier attributes
type of remote access service
rduske vu0Zdx0n3oZWFSaX encrypted password username
username rduske attributes
type of remote access service
eric 0vcSd5J/TLsFy7nU password user name encrypted privilege 15
lestofts URsSXKLozQMSeCBk username encrypted password
username lestofts attributes
type of remote access service
jpwiggins 3WyoRxmI6LZjGHZE encrypted password username
username jpwiggins attributes
type of remote access service
tomleonard cQXk0RJCBtxyzZ4K encrypted password username
username tomleonard attributes
type of remote access service
algobel 4AjIefFXCbu7.T9v encrypted password username
username algobel attributes
type of remote access service
type tunnel-group RemoteTunnel remote access
attributes global-tunnel-group RemoteTunnel
address pool VPNPool
Group Policy - by default-RemoteTunnel
IPSec-attributes tunnel-group RemoteTunnel
pre-shared key *.
tunnel-group 50.199.234.229 type ipsec-l2l
IPSec-attributes tunnel-group 50.199.234.229
pre-shared key *.
tunnel-group 98.101.139.210 type ipsec-l2l
IPSec-attributes tunnel-group 98.101.139.210
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmp
inspect the pptp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:6d1ffe8d570d467e1ea6fd60e9457ba1
: endCT OFFICE
Output of the command: "show run".
: Saved
:
ASA Version 8.2 (5)
!
hostname RaleighASA
activate the encrypted password of Ml95GJgphVRqpdJ7
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
192.168.5.1 IP address 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP 98.101.139.210 255.0.0.0
!
passive FTP mode
clock timezone IS - 5
clock to summer time EDT recurring
DNS lookup field inside
DNS server-group DefaultDNS
Server name 24.25.5.60
Server name 24.25.5.61
permit same-security-traffic intra-interface
object-group Protocol TCPUDP
object-protocol udp
object-tcp protocol
Wayne_Access to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.1.0 255.255.255.0
Wayne_Access to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.10.0 255.255.255.0
Shelton_Access to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.2.0 255.255.255.0
out_access_in list extended access permit tcp any host 98.101.139.210 eq www
out_access_in list extended access permit tcp any host 98.101.139.210 eq ftp
out_access_in list extended access permit udp any host 98.101.139.210 eq tftp
out_access_in list extended access udp allowed any SIP host 98.101.139.210 EQ
out_access_in list extended access permit tcp any host 98.101.139.210 eq 5090
out_access_in list extended access permit tcp any host 98.101.139.210 eq 2001
out_access_in list extended access permit tcp any host 98.101.139.210 eq 5080
out_access_in list extended access permit tcp any host 98.101.139.210 eq ssh
out_access_in list extended access permit tcp any host 98.101.139.210 eq 81
out_access_in list extended access permit tcp any host 98.101.139.210 eq 56774
out_access_in list extended access permit tcp any host 98.101.139.210 eq 5000
out_access_in list extended access permit tcp any host 98.101.139.210 eq 902
out_access_in list extended access permit tcp any host 98.101.139.210 eq netbios-ssn
out_access_in list extended access permit tcp any host 98.101.139.210 eq 445
out_access_in list extended access permit tcp any host 98.101.139.210 eq https
out_access_in list extended access allowed object-group TCPUDP any host 98.101.139.210 eq 3389
out_access_in list extended access allowed object-group TCPUDP range guest 98.101.139.210 5480 5487
out_access_in list extended access permits any udp host 98.101.139.210 range 9000-9050
inside_nat0 to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.1.0 255.255.255.0
inside_nat0 to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.2.0 255.255.255.0
inside_nat0 to access extended list ip 192.168.5.0 allow 255.255.255.0 192.168.10.0 255.255.255.0
pager lines 24
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0
NAT (inside) 1 0.0.0.0 0.0.0.0Access-group out_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 98.101.139.209 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
Enable http server
http 0.0.0.0 0.0.0.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-3des esp-md5-hmac WayneTransform
Crypto ipsec transform-set esp-3des esp-md5-hmac SheltonTransform
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
card crypto IPSec_map 1 corresponds to the address Wayne_Access
card crypto IPSec_map 1 set pfs Group1
card crypto IPSec_map 1 set peer 70.91.18.205
card crypto IPSec_map 1 the transform-set WayneTransform value
card crypto IPSec_map 2 corresponds to the address Shelton_Access
card crypto IPSec_map 2 set pfs Group1
card crypto IPSec_map 2 set peer 50.199.234.229
card crypto IPSec_map 2 the transform-set SheltonTransform value
IPSec_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 1
preshared authentication
3des encryption
sha hash
Group 2
life 43200
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 inside
SSH timeout 5
Console timeout 0
management-access inside
dhcpd outside auto_config
!
dhcpd address 192.168.5.100 - 192.168.5.199 inside
dhcpd dns 24.25.5.60 24.25.5.61 interface inside
dhcpd allow inside
!a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
eric 0vcSd5J/TLsFy7nU password user name encrypted privilege 15
tunnel-group 50.199.234.229 type ipsec-l2l
IPSec-attributes tunnel-group 50.199.234.229
pre-shared key *.
tunnel-group 70.91.18.205 type ipsec-l2l
IPSec-attributes tunnel-group 70.91.18.205
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:3d770ba9647ffdc22b3637e1e5b9a955
: endHello
I might have found the problem.
To be honest, I'm a little tired and concentration is difficult, especially when access between multiple device configurations. So second pair of eyes is perhaps in order.
At the moment it seems to me that this configuration is the problem on the SITE of PA
IPSec_Access to access extended list ip 192.168.10.0 allow 255.255.255.224 192.168.5.0 255.255.255.0
This is an ACL that defines networks the and remote for a connection VPN L2L.
Now, when we look at what connection VPN L2L this belong we see the following
card crypto IPSec_map 1 corresponds to the address IPSec_Access
card crypto IPSec_map 1 set peer 50.199.234.229
card crypto IPSec_map 1 the transform-set VPNTransformSet value
Now, we see that the peer IP address is 50.199.234.229. Is what site this? The IP address of the CT Site that works correctly?
Now what that said the ACL line I mentioned more early basically is that when the 192.168.10.0 network 255.255.255.224 wants to connect to the network 192.168.5.0/24 should be sent to the CT Site. And of course, this should not be the case as we want traffic to go on the NC Site
Also worth noting is that on the SITE of the above connection is configured with the '1' priority so it gets first compared a connection. If the VPN L2L configurations were in different order then the VPN Client connection can actually work. But it's just something that I wanted to point out. The actual resolution of the problem, of course, is to detach the configuration which is the cause of the real problem in which ASA attempts to route traffic to a completely wrong place.
So can you remove this line ACL of the ASA of PA
No IPSec_Access access list extended ip 192.168.10.0 allow 255.255.255.224 192.168.5.0 255.255.255.0
Then, test the VPN Client connection NC SITE again.
Hope that this will finally be the solution
-Jouni
-
VPN site-to-site remote access
Hello
I would like to know if the tunnel VPN IPSEC Site to site can coexist with a VPN tunnel to remote access on one device of PIX 515E
Thank you
Madan failed
Yes.
-
PIX - ASA, allow RA VPN clients to access servers at remote sites
I got L2L tunnels set up for a couple of remote sites (PIX) for several months now. We have a VPN concentrator, which will go EOL soon, so I'm working on moving our existing customers of RA our ASA. I have a problem, allowing RA clients access to a server to one of our remote sites. PIX and ASA (main site) relevant config is shown below. The error I get on the remote PIX when you try a ping on the VPN client is:
Group = 204.14. *. *, IP = 204.14. *. * cheque card static Crypto Card = outside_map, seq = 40, ACL does not proxy IDs src:172.16.200.0 dst: 172.16.26.0
The config:
Hand ASA config
access extensive list ip 172.16.0.0 inside_nat0_outbound allow 255.255.255.0 172.16.26.0 255.255.255.0
access extensive list ip 172.16.1.0 inside_nat0_outbound allow 255.255.255.0 172.16.26.0 255.255.255.0
access extensive list ip 172.16.22.0 inside_nat0_outbound allow 255.255.255.0 172.16.26.0 255.255.255.0
access extensive list ip 172.16.200.0 inside_nat0_outbound allow 255.255.255.0 172.16.26.0 255.255.255.0
access extensive list ip 172.16.0.0 inside_nat0_outbound allow 255.255.255.0 172.16.200.0 255.255.255.0
access extensive list ip 172.16.0.0 outside_cryptomap_60 allow 255.255.255.0 172.16.26.0 255.255.255.0
access extensive list ip 172.16.1.0 outside_cryptomap_60 allow 255.255.255.0 172.16.26.0 255.255.255.0
access extensive list ip 172.16.22.0 outside_cryptomap_60 allow 255.255.255.0 172.16.26.0 255.255.255.0
access extensive list ip 172.16.200.0 outside_cryptomap_60 allow 255.255.255.0 172.16.26.0 255.255.255.0
card crypto outside_map 60 match address outside_cryptomap_60
outside_map 60 set crypto map peer 24.97. *. *
card crypto outside_map 60 the transform-set ESP-3DES-MD5 value
map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map
outside_map interface card crypto outside
=========================================
Remote config PIX
access extensive list ip 172.16.26.0 inside_nat0_outbound allow 255.255.255.0 172.16.0.0 255.255.255.0
access extensive list ip 172.16.26.0 inside_nat0_outbound allow 255.255.255.0 172.16.1.0 255.255.255.0
access extensive list ip 172.16.26.0 inside_nat0_outbound allow 255.255.255.0 172.16.22.0 255.255.255.0
access extensive list ip 172.16.26.0 inside_nat0_outbound allow 255.255.255.0 172.16.200.0 255.255.255.0
access extensive list ip 172.16.26.0 outside_cryptomap_60 allow 255.255.255.0 172.16.0.0 255.255.255.0
access extensive list ip 172.16.26.0 outside_cryptomap_60 allow 255.255.255.0 172.16.1.0 255.255.255.0
access extensive list ip 172.16.26.0 outside_cryptomap_60 allow 255.255.255.0 172.16.22.0 255.255.255.0
access extensive list ip 172.16.26.0 outside_cryptomap_60 allow 255.255.255.0 172.16.200.0 255.255.255.0
card crypto outside_map 60 match address outside_cryptomap_60
peer set card crypto outside_map 60 204.14. *. *
card crypto outside_map 60 the transform-set ESP-3DES-MD5 value
outside_map interface card crypto outside
EDIT: Guess, I might add, remote site is 172.16.26.0/24 VLAN VPN is 172.16.200.0/24...
What you want to do is 'tunnelall', which is not split tunneling. This will still allow customers to join the main and remote site, but not allow them to access internet... unless you have expressly authorized to make a 'nat (outside)"or something. Your journey on the client will be, Secured route 0.0.0.0 0.0.0.0
attributes of group policy
Split-tunnel-policy tunnelall
Who is your current config, I don't see where the acl of walton is attributed to what to split tunnel?
-
Access even if remote site 2 site VPN
Hello
I'm under VPN between two sites using 2 ASA 5505.
Also, I want that RA - VPN which is accommodated in the two ASA.
My need is to remove one of access VPN - RA and keep only one, but must be able to reach the second site.
I did a split with two LANs tunnel. But I still not able to get the directions in my computer when I connect to the RA - VPN.
Is this possible? And how?
A few things that should be configured to access remote access vpn remote vpn site to site LAN:
(1) on cryptography from site to site tunnel ACL, it must include the subnet remote vpn client ip pool as follows:
On the SAA ending the vpn client: ip allow
On the ASA distance that ends the tunnel from site to site: ip allow
(2) on the SAA ending the vpn client: same-security-traffic permit intra interface
(3) on the ASA distance that ends the tunnel from site to site: NAT ACL exemption must include the Remote LAN traffic to the subnet IP Pool.
In addition, ACL split tunnel which includes two subnets which I believe you already configured.
Hope that helps.
Maybe you are looking for
-
Tecra 9100 - required accupoint driver for XP
Hello I need a MS XP driver for the accupoint of my new (used) Tecra 9100. Or at least I think, because the accupoint does not work and there is no configuration on the menus of the mouse tab. On the driver download page http://eu.computers.toshiba-e
-
SSD drive, Toshiba canvio aeromobile wireless fails to send the signal
disc ssd wireless works fine.copy files readings of wireless works fineWIRELESS DSS APP store updated without internet< strange="">after update 'wait 5 minutes and reconnect'Wireless hard drive fails to send a signal that can be picked up Troubleshoo
-
Acquisition of NOR-6602 delay and buffer overflow
Hello world I use an NI PCI-6602 to record photon arrival times. Basically, it counts the number of rising edges on the sample clock 80 MHz which occur between two risingedges on the photon TTL signal. The array of integers can be converted at a time
-
Update selected by program element combo box?
is there a node property or any other method that will allow me to update the currently selected item in a drop-down list programmatically? I am trying to build a routine whereby the user goes to an element (in reality a different graphic) by selecti
-
Windows compatible xbox 360 wired controller
Purchased windows compatible xbox 360 wired controller this seller assured me would work under Vista. But apparently not.I downloaded the latest driver suitable for the material and installed according to the instructions (with controller unplugged)