Multisite for C60

Similar Questions

• How to add a license via command line for C60 key

  Could someone remind me what the command would be to add a license key via the command line interface?  I want to downgrade the software and it was initially delivered with version TC7.

  Hello Douglas.

  Here are the commands:

  xCommand SystemUnit OptionKey Add Key(r):
  xCommand SystemUnit ReleaseKey Add Key(r):
  

  You can also enter them via the web interface by going to the maintenance > Software Upgrade.

• C40 Multisite call

  Hi all

  I have to configure multi-site/multiway,

  We have VCSC and MCU.

  and endpoints such as C40, ex90 and MXP1700.

  Ex90 has licence Multisite for C40, but it's not. Able to make P2P calls and then add other EX90 IAM conversation endpoints.

  We have a VCSC and MCU.

  How can I configure multiway help MCU?  I tried to set up an alias in VCS, Conference factory-22228

  and the model [email protected] / * /

  Conference factory State is active. 22228 added as base10 multiway on the c40. My prefix for MCU Conference Service is 8.

  I need to set up a permanent conference in MCU?

  I have to configure Permanent Conference as 22228?

  My SIP domain name is vcs.com

  Rgds

  Bobby

  Hi Bobby,.

  on the check of EX90 you added the multisite key. TC5 version wouldn't hurt.

  Do not use a version

  Some generic endpoint support information:

  http://www.Cisco.com/en/us/docs/Telepresence/infrastructure/articles/cisco_telepresence_mcu_configure_multiway_kb_166.shtml

  You can have multiway or multisite, so if you have already configured the EX90 for multiway

  This will be the reason why you can't add another local call, these features are mutually exclusive.

  If you delete the multiway address it should work again with multisite.

  Cordially conf multisite, check on the

  http://www.Cisco.com/en/us/docs/Telepresence/infrastructure/VCs/config_guide/Cisco_VCS_Multiway_Deployment_Guide_X7.PDF

  In short you must enable autocreateing of conferences with no PIN number prompt and have a prefix MCU

  recording, editing of your plant in conference setting, do not overlap with other conferences / MSDS

  Not to mention that I recommend the vcs, mcu and endpoint admin guides http://tandberg.com/docs is a good start

  Bobby, please note the answer with the stars below and set the thread if it's an answer!

• A MultiSITE call may be promoted to a MultiWAY call?

  I have a customer who currently has a number of endpoints with multi-site licenses, mainly 6000MXP units.  The client is developed to the point where 6-pin calls are no longer adequate, and they'll have to buy an MCU.

  My question is:

  Can the customer still enjoy the microcontrollers built in codecs 6000MXP and use a MultiSITE call until the participants are too many and then degenerate into a MultiWAY call?

  Will there be a way to migrate the customer to a MCU usage, perhaps by the personal use of alias of bridge?

  Hi Anthony!

  Can the client still take advantage of the built-in MCUs in the 6000MXP codecs, and use a MultiSITE call until such time as the participants are too many, and then escalate to a MultiWAY call?
  

  No, it is not possible to climb a call running Multisite for a call Multiway or MCU (MXP or C series).

  On the endpoints that will be able to launch the Multiway call is an exclusive setting, therefore,

  Select Multisite, Multiway (or completely disable a Multipoint).

  In addition Multiway must be supported by the endpoint, newest Cisco/Tandberg endpoints points support

  initiate a call Multiway and many (incl. 3rd party) support to be reunited to form a Multiway call.

  It is also dependent on the version of the software.

  In short, with Multiway may as end points that do not support being redirected

  for the MCU (for example the outer parts where you don't have conrtol from software versions,...)

  do not be reunited to form the Conference.

  Is there a better way to migrate the client to the use of an MCU, perhaps through the use of personal bridge aliases?
  

  
  Is there a better way to migrate the client to the use of an MCU, perhaps through the use of personal bridge aliases?
  

  To swap the MXP multisite with a microcontroller of HD Cisco (old Codian) is a great idea in any case, it will not focus only

  the capacity of the largest conferences but also improves quality. Each participant will receive its own optimized

  video stream instead of the single video stream where the worst participant defines what you will get.

  As you said, after meeting personal room numbers (with findme or certain rules of vcs, you can also do named uris,

  as [email protected] / * /), generic virtual meeting rooms or to book through TMS/Scheduler

  may be the solution.

• Registration of VCS for LINK C60 / ISDN

  Good people, another noob question: we have points of endpoint (Local) that are a combination of a Codec (C40 and C60) who are matched with an ISDN connection. The customer currently uses the Codecs from point to point and conference (4 participants) limited bridge. We bought a 5320 MCU, VCS and TMS. I'm a little confused on how we can get the Codecs and links properly registered and VCS (TMS).

  We must register those endpoints for VCS points and be controlled by TMS. We do not save the Codecs and links ISDN separately for VCS, and if so, we put the ISDN links in the area of ISDN?

  I can see on the Codecs that I can define a H.323 Gatekeeper, but I'm a little more naïve about how to save the ISDN links. I went through several "Getting Started" and the Configuration Guides for ISDN connection (and also for Codecs), but at the moment I'm a bit confused.

  Most of the video conferences will be by IP and maybe a single to an external endpoint ISDN connection. These conferences will be either point to point or bridge for a 5320 MCU.

  If anyone can point me to a good, concise reference source, I would be grateful.

  TIA and sorry to be a noob.

  Mark

  Hi Mark,

  As Patrick alluded above, I have experience with these things before.  Yes, you can save all your endpoints to your VCS points so they can all call each other and the 5320MCU, although the device that is attached to the ISDNLink will be capable of scoring calls or rear via ISDN.

  So, as you have summised above, the C60 with the ISDNLink to connect to ISDN part and then also participate in the Conference of 5320MCU.  This means that the C60 must get a Multisite License installed to manage calls video of what he'll do next part.

  If you have additional questions, feel free to ask.

  Wayne
  --
  Remember the frequency responses and mark your question as answered as appropriate.

• CARD READER USB FOR DESKTOP HP PAVILION 500 - C60?

  I have a new 500 - C60 HP Pavilion desktop computer, but the front card reader does not accept the largest flash Compact Flash (CF) card.  I have an old USB multi-card with four different card slots, which accepts the card see  Would this setting work satisfactorly?

  Thank you

  shamrock838

  Hello @shamrock838,

  I understand that your desktop HP Pavilion 500 - c60 PC does not support the biggest Compact Flash Memory Card and you are curious as to whether or not you can install an USB multicard Reader which accepts the memory card see First of all, you have reason 7 - in1 media card reader did it installed does not supported CF memory card, but it supports the following cards:

  • Digital safe™ (SD)
  • Secure Digital High Capacity (SDHC)
  • SDXC
  • Memory Stick
  • Memory Stick Select
  • Memory Stick PRO
  • Memory Stick MagicGate

  I don't see why you can't connect the 4 - in1 USB multicard reader you have. Until the operating system detects and installs, you should be fine.

  I hope that I have answered your question to your satisfaction. Thanks for posting on the HP Forums. Have a great day!

• How to check that the C40 is an option for multisite

  Hello

  Do my first multisite with new C40 and for some reason, no audio or video is received on each side of a 3-way call.  2-way standard calls work perfect.  We do not use a gateway.  The software version is TC4.2.1.265253.  I have 3 other side of 95 to this place that work very well.  None of the additional steps were needed to those that relate to a multisite call.  I went through the menu of the C40, but I don't see any options that seem out of place.

  THX!

  GB

  Also, you can check the xstatus systemunit and find these details to see if the Multisite License is present on the codec:

  
  

  * s SystemUnit software OptionKeys MultiSite: 'true '.

  * s SystemUnit State MaxNumberOfCalls: 4

  * s SystemUnit State MaxNumberOfActiveCalls: 4

  * s SystemUnit State NumberOfActiveCalls: 0

  * s SystemUnit State NumberOfSuspendedCalls: 0

  * s SystemUnit State NumberOfInProgressCalls: 0

  Kind regards

  Saint André

• Implementation of Cisco C60 for a test site

  Hi all

  I have two C60 codecs, sitting on the same network (not provisioned, not set up for video conferencing).

  Could someone please explain how to set up these two codecs for a VTC test site? I found a few sites testing, IPs, etc, but I don't know what to Setup. The advanced on the device configuration page is not very helpful.

  These two devices can call the each other without some sort of setup of service? I'm fairly new to this area, so I really appreciate your help on this.

  Thank you

  Sinan

  Hello

  First ping the end this codec the codec you use for membership and see if you get resonce.

  SystemTools network ping xxx.xxx.xxx.xxx

  If you have found answer then use suite commnad ro dial.

  xcommand Dial Number: xxx.xxx.xxx.xxx Protocol: h323

  HTH

  Kind regards

  Dharmmesh

• SX20 camera usb connection / why no support for C40, C60, C90?

  Hi, I noticed that the versionTC6.2.0 of running of Cisco SX20 software now supports usb cameras. It looks like the UVC device drivers are loaded with the sx20.

  I tested with HD Precision USB camera and it worked fine. (Mainvideo source: 3).

  I was not able to find information about this new feature in the release notes, so I think it's not official yet?

  I noticed that with TC 6.2.0 C40 does not have the same option available. The support is coming for C-series together?

  This feature might be useful when you need a second temporary camera or jumps to the main camera.

  Tom br.

  Hi Tom,

  The covering memo has video input USB source information.

  SX20: xStatus video Input Source 3 resolution height

  SX20: xStatus video resolution width Input Source 3

  SX20: xStatus video Input Source 3 resolution RefreshRate SX20: xStatus video Input Source 3 resolution FormatType SX20: xStatus video Input Source 3 resolution FormatStatus SX20: xStatus video input USB 3 connected

  SX20: xStatus video input USB 3 SignalState

  But yes, I wasn't able to find a formal update on this part.

  can't comment on the use of USb on the C series, because ports are not currently active on the Sx however they are used for serial interface.

  Maybe we can expect furture for C series however his (maybe)

  Concerning

  Ravi kr.

• Site to Site VPN IPSEC for multisite with dual ISP failover

  Hello world

  I have total 6 ASA 5505, I already built failover with double tis. Now, I want to configure site 2 site VPN for all 3 sites. Each site has 2 firewall.

  I just built a config for 2 a site WHAT VPN here is the config for a single site.

  local ip address: 172.16.100.0

  IP of the pubis: 10.5.1.101, 10.6.1.101

  Remote local ip: 172.16.101.0

  Remote public ip: 10.3.1.101, 10.4.1.101

  Remote local ip: 192.168.0.0

  Remote public ip: 10.1.1.101, 10.2.1.101

  the tunnel on the first 2 firewall configuration:

  IP 172.16.100.0 allow Access-list vpn1 255.255.255.0 172.16.101.0 255.255.255.0

  backupvpn1 ip 172.16.100.0 access list allow 255.255.255.0 172.16.101.0 255.255.255.0

  ip 172.16.100.0 access VPN2 list allow 255.255.255.0 192.168.0.0 255.255.255.0

  backupvpn2 ip 172.16.100.0 access list allow 255.255.255.0 192.168.0.0 255.255.255.0

  IP 172.16.100.0 allow Access-list sheep 255.255.255.0 172.16.101.0 255.255.255.0

  172.16.100.0 IP Access-list sheep 255.255.255.0 allow 192.168.0.0 255.255.255.0

  !

  !

  NAT (inside) 0 access-list sheep

  NAT (inside) 1 0.0.0.0 0.0.0.0

  !

  !

  !

  crypto ISAKMP allow outside

  ISAKMP crypto enable backup

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  sha hash

  !

  !

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac my-set1

  card crypto outside_map 1 match for vpn1

  peer set card crypto outside_map 1 10.3.1.101

  My outside_map 1 transform-set-set1 crypto card

  outside_map interface card crypto outside

  !

  !

  card crypto outside_map 2 match address backupvpn1

  peer set card crypto outside_map 2 10.4.1.101

  My outside_map 2 transform-set-set1 crypto card

  backup of crypto outside_map interface card

  !

  !

  !

  Crypto ipsec transform-set esp-3des esp-sha-hmac my-set2

  crypto outside_map 3 game card address vpn2

  peer set card crypto outside_map 3 10.1.1.101

  My outside_map 3 transform-set-set2 crypto card

  outside_map interface card crypto outside

  !

  !

  card crypto 4 correspondence address backupvpn2 outside_map

  peer set card crypto outside_map 4 10.2.1.101

  My outside_map 4 transform-set-set2 crypto card

  backup of crypto outside_map interface card

  !

  !

  !

  tunnel-group 10.3.1.101 type ipsec-l2l

  IPSec-attribute Tunnel-Group 10.3.1.101

  pre-shared key cisco

  ISAKMP keepalive retry 20 3 threshold

  !

  !

  tunnel-group 10.4.1.101 type ipsec-l2l

  IPSec-attribute Tunnel-Group 10.4.1.101

  pre-shared key cisco

  ISAKMP keepalive retry 20 3 threshold

  !

  !

  tunnel-group 10.1.1.101 type ipsec-l2l

  IPSec-attribute Tunnel-Group 10.1.1.101

  pre-shared key cisco

  ISAKMP keepalive retry 20 3 threshold

  !

  !

  tunnel-group 10.2.1.101 type ipsec-l2l

  IPSec-attribute Tunnel-Group 10.2.1.101

  pre-shared key cisco

  ISAKMP keepalive retry 20 3 threshold

  !

  !

  backup of MTU 1500

  If this correct what should I configure other side that I want to finish in front of it. Is my address name vpn1 crypto card must match on the other side or not?

  any suggestion is good...

  Thank you...

  What I mean with the routing is a routing protocol or static routes the SAA can choose between interfaces to establish the tunnel.

  If the ASA has the card encryption applied to two interfaces, then one should be used as primary and the other as backup.

  How will be the ASA choose which is better? Via the routing.

  If you use a routing protocol, the ASA will be known which interface to send packets every time, but if using static routes, you need to change the metric and configuring IP SLA.

  Federico.

• Resolution always falls on a multisite call if a Premium license is active?

  Hello

  Multipurpose codecs, the resolution will drop when a multisite call is established using the multisite aboard hook function.  Chip resolution steps for the bottom of endpoints:

  Changes of SX20 resolution to 576 p 30

  C40 resolution to 576 p 30 changes

  Changes of C60 resolution at 720 p 30

  C90 changes resolution 1080 p 30

  If you apply a Premium resolution license to the codec, the resolution still drop?  are they the same?  or at least get bumped slightly higher?

  If it does not increase the resolution, how does it increases for each model?

  Hi Kris,

  It will still drop, regardless of PR - key.

  Thank you

  Marius

• Dual monitor Option available in C60

  Hello

  I was setting up a C60 Nomenclature for one of my clients. By making a selection in the option of software feature, I was able to get to select Lic for Multisite and Premium resolution, but not dual display.

  Is there is some other partcode to select the dual display option or it is by default when we order C60. Also, in the description of C60 partcode nothing was mentioned for DD Lic.

  Reagards,

  Aastha

  Hello

  Dual license is not required for another series, such as C40, C60 and C90, for example.

  Cisco reference:

  https://supportforums.Cisco.com/docs/doc-36583

  Concerning

  Paulo Souza

  My answer was helpful? Please note the useful answers and do not forget to mark questions resolved as "responded."

• Tripartite Cisco C60 or C90 Cisco Conference

  Dear Experts,

  Cisco C60 or C90 of Cisco, codecs that have key MultiSite option allows to display image on screens separate the multipoint Conference, for example to display each participant on a screen connected to the codec during three separate?

  Your prompt response is much appreciated.

  Kind regards

  Nick

  Yes, you must use the composting and the TC console features. See attached link...

  http://www.Cisco.com/en/us/docs/Telepresence/endpoint/codec-c-series/TC6/tc_console/codec-c-series_tc-console_tc60.PDF

• Pavilion 500 - C60: new office reads, "ERROR: no boot disk was detected or the disc has failed" at startup.

  Just bought Pavilion 500 - C60, running Windows 8.1 64-bit and am doing everything on old HP running Windows Vista Home Premium SP 2. Has not gone smoothly from one thing to another, but I think everything comes together. A couple of days, began to receive the error message at startup or, if I COULD do so that it starts would go for awhile and then would get an ERROR message, requiring restart. Usually after obtaining the error message several times, the computer would then initialize. Tonight, I couldn't override the error message for anything! When you press power button / stop, I hear (HD) running for a few seconds, everything is silent, and then the error message appears on the gray screen dark in white letters, BACK very and sinister looking! Any suggestions? Had the computer about two months and it has not been easy.

  Not good!  Check all the connectors and the hard drive to make sure that they are correctly wired in place. Make sure that your cable is not reversed.

  Contact the seller if still under warranty for repair.  This could be the hard drive or motherboard and the problem lies the only diagnosis from a repair facility.

• Pavilion 500 - c60: product key

  If I chose to load Windows 7 Home OS on the 8.1 that sits on the newly purchased Pavilion 500 - c60 will be I had problems? AND if I choose to RELOAD 8.1 on the computer in the future how do I get the product key if as you say his anchored in the bios?

  Thanks for your replies. My reason for decommissioning is a requirement with my Autocad Architecture 2012 which does not work on windows 8.1. Stupid me! I should have looked into this before buying the computer. But I like the computer because it is a 64 bit with 8 GB of memory and I love the W8.1 too. Very compatible with my ph sound cell phone android. So until I can afford to upgrade my Autocad I'm stuck with Win7.