My computer is not forward from the Bios, he said: 3rd master hard disk error? (Processor core 2 quad, mother board MSI G41 - P26) Help me!

Similar Questions

• Pavilion dv6-3025dx: cannot boot in the bios because of a SMART hard disk error

  My hard drive has failed and now I'm making constant pop ups to replace

  I think Windows to transfer to an external drive until I can replace internally, but I need to access the bios to set the options for monitoring of the boot every time I use f10 to start in the bios it is as if it is popped and gives me the error screen smart disk where my only options are to start windows or run diagnostics.

  I tried to run the diagnostic, but each test resulted in an instant failure.

  Yes, get out of the hard drive and connect it to another PC. Get assistance from your service manual for the procedure to apply for, it:
  http://h10032.www1.HP.com/CTG/manual/c02659236

  Adapter, something like this: Http://www.amazon.com/Anker® - converter - adapter - cable - included / dp / B005B3VO24

  To configure the boot order, try this:
  http://support.HP.com/in-en/document/c00364979

  Press f9 key shortly after switching on laptop, if the above does not work.

  Concerning

  Visruth

• Windows 7 for Lenovo G50-70 - the computer will not boot from the CD

  Hello world

  I hope that someone here will be able to help

  I bought a new laptop with Windows 8.1. I want to install Windows 7 on that I know well because I can't use the new windows. I changed the settings in the BIOS to get the machine to boot from the CD, but it won't be fair. I also tried to restore the system to boot from the CD, but it installs just the Windows pre-installed, new instead. Also, I can't access the CD from the drive while all my other computers are capable of (what is strange)

  Can someone help, please?

  See you soon

  PS. : I can turn on the computer through the small "boot botton" on the side and select the DVD drive to boot from. But this is not followed by the message "Press any key to boot from CD" and the computer starts just W8 yet;

  I contacted customer service and followed your advice. They refused to help him on the ground that there nothing wrong with the machine in their opinion, and since I wanted to change operating system. All preinstalled spyprogrammes Lenovo has been erased with this downgrade. So far, I've owned a laptop computer brand new and expensive for a year I used only to waste my time, trying to make it work, that was not why I bought it in the first place. What a RIP-OFF!

• My computer does not load past the Bios Dell screen

  Vista 32 bit Home Premium on Vostro 200
  Hey, my name is Christian and this is my problem:

  It all started last night when I (stupidly) decided I should change my screen windows open, you know, black screen, where the green bar would float through from left to right while the computer responsible. I decided to change to a sort of landscape of Lake, but this is not the point.
  Before that, I chose at the next restart, the registry would be defragged and there would be controls memory.
  I am so down and restart the computer.
  Computer turns on and I the landscape to the instead, loading screen unless it's just a picture, so there is not move bar telling me whether or not the computer was loading.
  And the screen just wouldn't change. I assumed that defragments the registry and memory check took place, but I was rather paranoid about whether or not something is going on I turned manually the computer off hold the button down.
  I turned it back again and he went to the same - screen landscape and would not pass as usual. Paranoia took ahold of me and I turned it off once again. I did it a couple of times (and I apologize) until a system repair came automatically.
  I thought it was my way out of this problem, but it didn't really fix anything, and the screen landscape had changed now in a black screen which seems to have a background image screen to vista aurora discoloration in the Center.
  And it's right now. It does not seem to go beyond that and I think now that it was all due to the change in the loading screens.

  I even left on overnight assuming the scans took place and it would be frozen until the tests were performed.
  Nothing has changed.

  I tried the obvious; safe mode does not work exactly. I click on it and all I get is the names of the drivers being loaded then a very slow black line through every driver leading one by one.

  Unfortunately, I deleted the backups of my restore system checks an hour before this happened and I did a lot of memory by pressing F8 and choose the option.

  I'd even do a factory reset as long as I've had all my files and drivers on a hard drive.

  I don't know what to do, I am completely distraught. Any advice would be helpful and thanks in advance!
  (a factory reset would be VERY VERY last resort)

  Christian.

  Hello

  as safe mode does not do a start-up repair disc

  the link below is how to download and get a vista disk startup repair, which you can start from the

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  Here's how to use startup repair system restore command prompt, etc. to bleepingcomputers link below

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  to boot from the dvd drive to be able to you will see a way to get into the bios Setup at the bottom of the screen or command menu start

  It would be F2 or delete etc to enter the BIOS or F12 etc. for the start menu

  Change boot order it do dvd drive 1st in the boot order

  http://helpdeskgeek.com/how-to/change-boot-order-XP-Vista/

  If it does not here's how to save your data

  1. remove the hard drive and it slave in another computer

  2 buy or borrow a USB disk drive hard put in yout case then plug it into another computer and read the hard drive like this

  3. try Knoppix

  http://www.Knopper.NET/Knoppix/index-en.html

  BUT this method depends on your hardware in the computer that failed!

  and how to reinstall vista

  using dell dvd

  http://supportapj.Dell.com/support/topics/global.aspx/support/DSN/en/document?journalid=67E9C215C4BABD6CE040AE0AB5E14F05&docid=339949

  using the dell recovery partition

  http://supportapj.Dell.com/support/topics/global.aspx/support/DSN/en/document?journalid=67E9C215C4BABD6CE040AE0AB5E14F05&docid=336966

• Computer will not download from the internet

  I saw on this site that other people have similar problems with Vista suddenly refusing to download anything on the internet, even if they use a different browser.  Personally, I use Firefox and the same problem occurs even if I use IE.  I tried all the methods disabiling my Add-ons, restarted my laptop, etc.  No one answered that these methods have worked.  I don't see if it is malware on my laptop because I can not download the removal tool.  I was able to download Vista SP2 and other updates, but that was it.  Nothing else does.  Is there another way to solve this thorny problem?  This issue started back around April of this year after an update for an Ipod.

  Try the above and if no help do the following:

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Try to run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  If no joy:

  Try the Startup Repair tool-

  This tells you how to access the System Recovery Options
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  Try recovery options Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  Try runnng Chkdsk of Recovery Options
  (it of a more efficient way to manage to restart the computer and might work)
  Rob - bicycle - Mark Twain said it is good.

• computer does not start after the BIOS screen

  My computer froze when I was able to do it after a few minutes I turned off the computer.  My mistake, now I can not get windows to load. The monitor

  becomes black after the dell logo appears.  The only options I have are F2 and F12.  What other options I have to troubleshoot? Thanks in advance

  for all the answers

  Hello

  see if you can run the dell Diagnostics

  http://support.Dell.com/support/topics/global.aspx/support/KCS/document?c=us&CS=19&l=en&s=DHS&docid=DSN_A9E3A15597A04AFBB02EE16785D39C5C&isLegacy=true

  and use step 3 it if it finds an error

• My computer does not load from the beginning to need help

  I have a footstool of G62-224HE model HP laptop Windows 7-64 bit OS, before my broken laptop I downloaded my regular system updates when I rebooted my computer to finish my updates, it got stuck in a loop from loading until you see the logo windows and return to the beginging , so I did a Test drive and it kept failing the system repair lights forever and load dosen't system restore. What can I do?

  Thanks, I'll buy a new hard drive, which causes a malfunction of the hard drive? Is it possible to extend the life of a hard drive?

• How to reset the screen to start a SMART HARD DISK ERROR

  Hello

  I have a presario CQ56 ((XH167EA) which gives an error screen almost immediately at startup "smart hard drive control has detected an imminent failure".

  I checked the drive Samsung HM321HI with Seagate Seatools for DOS and it confirmed 4 errors (either incidentally, Seatools does not fix the errors of Samsung, although they admit, it should, like Seagate look after "Samsung" readers - they say they "work on it"..)

  I know I have to replace the hard drive thereafter, but have backed up all my files, etc. and the problem does not appear to be a lot worse (for now...).  I am a clear user and am glad to use it until it dies, then buy a replacement.

  Is it possible to stop this form to appear at startup.  My bios is updated.

  And, Yes, it is legitimate!

  In addition, the player is now just out of warranty, but if I can identify when the BULLET is fired, HP will honor the warranty if it is triggered in the warranty period?  I think I can guess the anwer, but worth asking maybe, if anyone knows the rules of HP on this...

  Thank you.

  HA, I know my limits!  We'll leave it at that then - thank you very much for your help with her.

• Computer does not start after the screen of the bios, Compaq Presario SR1023WM

  Ok. Trying to fix a friend's computer and seem to have met a strange barrier.

  Problem: The computer does not start after the bios screen.

  Details: When you turn on the computer, the compaq logo with intel inside is and has the < F1 Setup > and < F10 System Recovery > options listed as well.  And that's it as far as the computer becomes.  After that the computer just locked up, no work of buttons on the keyboard lights keyboard ect ect.  I tried the puree on the F1 key, as soon as I turn on the computer and I can handle so he can say * entering setup * but it freezes again after this point.  I already tried to eliminate the possible sources of the problem, removed all expansion cards, HDD and Dvd Rom module only disconnected, only memory (256 MB ddr 2700), power, vga and keyboard connected.  Ive also used the jumper on the motherboard to clear the cmos, hoping that would solve the problem without success.  I tried using a different memory stick and different memory as well...  Tried to use both a ps2 and a usb keyboard... Ive even tried pulling the rider for the protection of the bios password (even if she did not have a password on it, just try everything I can think of).

  The installed bios version is 3.1, and that's all that I know on the computer at this point, except that the website tells me to him.

  http://h10025.www1.HP.com/ewfrf/wc/product?product=411354 & LC = on & CC = US & DLC = in & Submit.y = 5 & Submit.x = 3 & lang = to & CC = US <-link to the Web page for the model #.

  I'm basically at a loss on this one, so if someone feels scroll line-by-line of their brains on this one, I'd be very happy.

  I have a pretty strong understanding of computer repair, so feel free to give me something to try.

  If you need more information out of me, let me know as well.

  Try to clear the CMOS again but this time remove CMOS battery and hold the power button on a few seconds. Replace the battery, then try to start back to the top.

  At the back of the pc is the condition of the PSU led green or flashing?

• computer Vista Home network is not visible from the XP computers

  I have a home network with 4 computers. Both run Windows XP, Windows Vista is running and
  It works in Windows 7. Each group can see all the others and can access shared files and printers
  with one exception. Vista computer is not visible from the XP computers. It is visible from
  the Windows 7 computer. I guess that there is a setting somewhere on the Vista machine
  That I need to change, but I'm not.

  Thank you.

  David

  Hello

  see Help for these links if

  http://Windows.Microsoft.com/en-us/Windows7/networking-home-computers-running-different-versions-of-Windows

  Networking of computers running different versions of Windows

  http://Windows.Microsoft.com/en-us/Windows-Vista/setting-up-a-home-network

  Setting up a network home

  http://TechNet.Microsoft.com/en-us/library/bb727037.aspx

  Vista File and Printer Sharing

• ProBook 4530 s BIOS update fails - "...". the computer is not connected to the external power supply. »

  I made an update of the system to the original settings and everything seems to go as usual.  While performiong the many windows updates, I noticed that the battery indicator indicates "no battery installed.  I found a few solutions dealing with this problem (none of the other solutions worked) and that which is shown updating BIOS.  I checked and the BIOS is F.07 and the current version is F.41.  I downloaded the update and begun the process of Windows.  The system restarts to start the process, but when the BIOS updated starts I get the following message:

  "A significant update of the BIOS of the system is available, but the computer is not connected to the external power supply.  Please connect the external power supply and then press Enter to continue. »

  The computer is connected to the power of HP to the original address since it is the only way so he can turn it on.  I tried removing the battery and from the update only the connected power and get the same result.

  Either way, I tried to insert a different battery, I have more than one of these laptops.

  Sorry

  Please test the battery after boot press F2 HP Diagnostics

  http://support.HP.com/us-en/document/c00821429

  and calibration of the battery for laptop

  http://support.HP.com/us-en/document/c00817650

• Vista 64 does not start after the bios screen. Can not boot from the recovery cd or help

  Last night a MS pushed a windows update and my pc restarted automatically.  But it does not actually restart.

  The PC goes through the bios tests, passes and then crashes and does not start in Vista.

  I can't start at all, including safe mode.

  I can't the system recovery option in HP bios to load.  Can I only use my Vista64 system recovery bootable cd or actually start.

  First of all, I thought it was a HARD drive problem, but tests of the bios disk hard that all spend, even the 2 hours 'SMART' test that he was running.

  Help

  Hello

  What happens when you try to boot from the recovery CD? You receive messages or error codes?

  You can check if the boot in the BIOS settings priority is configured to boot to CD\DVD.

  NOTE: Change (CMOS) BIOS/complementary metal oxide semiconductor settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  For more information, you can consult the following article:

  BIOS: Frequently asked questions

  If you still experience the problem, you may need to contact HP for assistance.

  HP support

  Hope this information is useful.

• Stops on his own computer and will not boot from the CD

  someone entered cmd and did something to my computer, now, the computer shuts itself, what can I do I tried to reinstall windows and the computer does not start from cd?

  * original title - someone entered cmd and did something to my computer, now, the computer shuts itself, what can I do I tried to reinstall windows and the computer does not start from cd? *

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  See you soon.

  Mick Murphy - Microsoft partner

• CD player passes all tests but the computer does not start from cd player

  CD player passes all the tests, but the computer does not start from cd drive. entered the bios and it specifically indicate to boot from the cd drive. Windows 7 installation disc does not start. Win 7 disk works in another computer to start. Why is it not this cd player read the disc and from the win 7 installation process?

  I see this problem on systems having older IDE and SATA drives requiring firmware updates and assigned to the region 1 aka they boot from XP CD, but not DVD windows 7or media.

• my computer would not wake from sleep when the cover iclose & open again?

  When I close the lid on my computer & open it again, the computer does not wake up, it shows just a black screen!

  Hi George,.

  From the description of the problem, it seems that the computer would not wake from sleep when you close the lid and open it again. I understand the inconvenience.

  Let us, try to perform the following methods and check if it helps.

  Method 1: Run the troubleshooter of power

  Open the troubleshooter of power

  http://Windows.Microsoft.com/en-us/Windows7/open-the-power-Troubleshooter

  For more information, connect to:

  http://Windows.Microsoft.com/en-us/Windows7/sleep-and-hibernation-frequently-asked-questions

  Method 2: Troubleshoot wake the computer from sleep mode

  http://support.Microsoft.com/kb/266283

  Method 3: Update Chipset drivers

  Download and install the latest version of drivers for chipset for the computer on the computer manufacturer site and check if you are faced with the same question.

  Method 4: Run the BIOS update

  I would say as you perform the update of the BIOS by contacting the manufacturer of the computer, check if it helps.

  Important: Change (CMOS) BIOS/complementary metal oxide semiconductor settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  It will be useful. For any other corresponding Windows help, do not hesitate to contact us and we will be happy to help you