MY laptop gets a strong signal from router but it does not connect to the internet.

Similar Questions

• My HP shows it is connected to the new router, but does not connect to the internet. How should I do?

  I have a HP G60 Notebook PC with Windows Vista Home Premium, it is about 4 years old. I recently got a new Cisco Linksys E1500 wireless router, which is connected to my home computer. My laptop shows that it is connected to the home network, but it does not connect to the internet. Other laptops in the House are able to connect to the network and to the internet. Mine seems to be the only one not working do not. Why it is not working? What should I do about it?

  I ran the network diagnostics. It is said "a problem with you network router or modem broadband could prevent an internet connection." I have disconnected these two and tried again. It did not work! I have also connected my laptop directly on the modem and it does not always connect to the internet. I tried to reset the network card. My IP settings are set to automatic.

  My internet connection was not a problem before last week (when I got a new router). What is the problem with my computer? Help, please!

  Hello:

  If you have an Atheros wireless adapter in your PC and you have not updated the driver, I recommend that you install it.

  http://h20000.www2.HP.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=321957&prodSeriesId=3688868&swItem=ob-99392-1&mode=3

  Wireless adapters Atheros with former pilots, dislikes the new Linksys routers.

  If you have an Atheros wireless card, and your wireless driver is more than 2 years, I am very confident that this will solve your connection problem.

  Paul

• Bought LR6 DVD but the installer does not connect to the internet for I can register it.  I downloaded the trial version to work around this problem, but I can't get the program to start.  I get the same message that I should connect to the internet and c

  Purchase DVD LR6 Adorama, but Setup does not connect to the internet so that I can record.  Internet works fine.   I have Adobe account.

  I went to Safari to Chrome and downloaded the trial version in the hope to bypass the DVD version, but I can't get the program to start.    I get the same message that I should connect to the internet and connect.  It seems impossible after 3 hours.  Spent an hour chatting with the support of the India.

  Also remove the cookie file and reg Lightroom then enter the serial number and check.

  Windows:

  Press Windows button (located between Ctrl and Alt buttons) with the key R together at once, you will get a command window.

  Type below command and press the enter"" key.

  programdata %

  It will open the ProgramData folder. inside locate Adobe folder.

  Go to Adobe > Lightroom.

  Open Lightroom and delete all the files inside,

  Then run LR 6 and enter the serial number,

  Mac:

  (1) right-click on the icon in the Finder, then select the 'Go - To Folder' option.
  (2) you will get a text box, type in the following command and then press the 'return '. (" Do not miss ~ symbol" "')

  ~/Library

  It will open the folder of the user's library.

  (3) then navigate to Application Support > Adobe > Lightroom.

  Open Lightroom and delete all the files inside,

  Then run LR 6 and enter the serial number,

• I installed a new router (Netgear N300) wireless and my laptop is the only computer that does not connect to the internet.

  Connected to the new router, but locally only.

  Currently, I installed a new router (Netgear N300) wireless and my laptop is the only computer that does not connect to the internet. The small icon to the left of my screen says only: ACCESS: LOCAL ONLY.
  BASICALLY,.

  I have Windows Vista Home Premium, notebook Compaq (Presario CQ60 to be exact)

  I can connect if I use a cable, but its disadvantages.

  I can connect wirelessly with my PC and Ipad. and Internet access.

  I TRIED:
  Various patches microsoft such as resetting TCP, safe mode with network, reset the router. »

  Thank you in advance and we hope you can answer this soon!

  I use an Atheros AR5007 802. 11 b / g WiFi Adapter(Compaq laptop) for the moment so this is useful. Thanks again!
  Someone suggested that I update my wireless driver. I am open to this idea, if anyone can find a safe and legal site with the download.

  Hi Bryyaan11,

  You can check out the link to HP support and try to download the drivers for your wireless card updated:

  Support HP & drivers

  For more information, you can also consult the following article:

  Updated a hardware driver that is not working properly

  You can also check the following items and try the steps:

  Windows wireless and wired network connection problems

  Solve problems, find wireless networks

  Hope this information is useful.

• I just installed a new router and now my desktop running Windows XP computer does not connect to the internet.

  Hello

  I just installed a new router and now my desktop running xp computer does not connect to the internet. I know that it is not the router because I plugged the cable into my laptop running 7 and it works fine. When I try to dhcp I get 169..., when I put manually the IP just get no access to the internet and can not ping to the router address. I tried to run the net work Assistant, emptied my dns, disabled all firewals, still nothing.
  Any suggestions?
  original title: connectivity Limeted

  The zero configuration utility works very well. But it is a desktop computer and on cable. All other wired and wireless PC in the office is working well, then it's definitely this PC. He came out of nowhere, I install a network printer on the PC but that's all.

  Your messages are a bit terse, but if I understand correctly

  • You have a router connected to the Internet and multiple computers connected to the router, some Ethernet cable and others by wireless.
  • All but one of these computers can reach successfully from the Internet via the router.
  • A computer that can't browse the Internet is connected to the router via an Ethernet cable.
  • You disconnected the cable between the router and the desktop problem and connected it to a Windows 7 laptop and the laptop connected to the Internet via the router.
  • You haven't seen any error message (except, perhaps, a message on "Limited or no connectivity").
  • You have installed Windows XP Service Pack 3 (or at least Service Pack 2)

  Assuming that all the foregoing is an accurate summary of the situation, I suggest that you do the following:

  Open a command prompt window (start > run > cmd > OK)
  Type the following lines and press ENTER after each line

  Netsh reset winsock catalog
  netsh int ip reset c:\resetlog.txt

  Close the command prompt window and restart the computer.

• Laptop does not connect to the internet. error cannot display Web page

  Original title: laptop does not connect to the internet. How can I fix it?

  I'm trying to get my laptop to connect to internet, but it will not. It keeps telling me that it cannot display the Web page. The wireless connection is the link and he sees the laptop, but it's like he goes. How can I fix it? Help!

  Hello

  1. Have you tried using anythird party web browser to connect to Internet?
  2. You use Internet Explorer to surf the Internet?

  If you receive error message cannot display Web page in Internet Explorer, then you can check the link below to fix the problem.

  "Internet Explorer cannot display the webpage" error when you view a Web site in Internet Explorer

  http://support.Microsoft.com/kb/956196

  Note:

  Reset the Internet Explorer settings can reset security settings or privacy settings that you have added to the list of Trusted Sites. Reset the Internet Explorer settings can also reset parental control settings. We recommend that you note these sites before you use the reset Internet Explorer settings

• I have a problem with my laptop does not connect to the internet. It connects to our wireless very well, but it doesn't have an internet connection.

  I have a problem with my laptop does not connect to the internet. It connects to our wireless very well, but it doesn't have an internet connection. It connects to other networks wifi very well with Internet access, is that the wireless in my house what it connects to. When I diagnose the problem, it says "Cannot communicate with DNS server (208.67.222.222)", and then under that it says: "languished network diagnostics remote hosts, but had not received a response." It connects to the Internet through an ethernet cable, but it is rather annoying pulling the cable autour. I currently have Windows Vista Home Premium. Thank you!

  original title: Internet connectivity problem

  Hello

  Now, you may need to contact the support of Panda Internet Security centre to change the settings so that wireless is enabled through it.

  Support link: http://www.pandasecurity.com/homeusers/support/

• (GET MORE) On a printer C309n Hp Photosmart Premium Web application does not connect to the internet?

  Hello everyone; Does anyone know why the app GET MORE on this printer Hp Photosmart Premium Web C309n does not connect to the internet? All other applications are connected ok. The site is down? someone knows something about it? HP is the fixation of this hopefully soon? Thanks for any info.

  I am very sorry for your difficulties.

  You can try the following, if you please, of your printer face:

  Setup (wrench on sceen House of printer)

  Web

  Updates

  Product updates

  Accept the update of product offered.

  Please let us know:

  (1) if he is offered an update of product, and if so, it ends correctly?

  (2) receives more work after the update?

  In the future you can keep your FW up-to-date more easily by selecting the option 'Automatically' for the settings of update of product in the update section of the product in the Web menu.

  Key

  Web

  Updates

  Product update settings

  Select "automatically".

• Laptop does not connect to the internet, office. Both use the same router. Tried troubleshooting, does not. Help!

  I have a desktop computer and a laptop. Both use the same router. The laptop does not connect to the network, but the office has no problem. My wireless adapter on the laptop is on, I tried troubleshooting. I tried to turn it off for 30 seconds then restart him. But nothing is resolved the problem. Any ideas would be helpful! Thank you

  Hello

  Maybe this can help.

  These steps and tell us where is the breaking point.

  Check the Device Manager for the wireless card valid entry.

  http://www.ezlan.NET/Win7/net_dm.jpg

  If there is no valid entry, remove any entry from fake and re - install the drivers for the wireless card.

  Check network connections to make sure that you have a network icon/entry wireless connection, and that the properties of the icon (right-click on the icon) are correctly configured with the TCP/IPv4 protocol in the properties of network connections.

  http://www.ezlan.NET/Win7/net_connection_tcp.jpg

  Make sure that if there is Wireless Utility a utility vendor is not running with the native Windows wireless utility.

  ----------------

  Make sure you firewall No. preventing / blocks wireless components to join the network.

  Some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible set up the firewall correctly, otherwise totally uninstall and get rid of its remaining processes that permit the own local network traffic flow.

  If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  ---------------------------

  Stack TCP/IP work should look like.

  Right-click on the wireless network connection card, select status, details and see if she got an IP address and the rest of the settings.

  http://www.ezlan.NET/Win7/status-NIC.jpg

  Description is the data of the card making.

  The physical address is MAC of the card number.

  The xx must be a number between 0 and 255 (all xx even number).

  YY should be between 0 and 255

  ZZ should be between 0 and 255 (zz all the same number.)

  The date of the lease must be valid at the present time.

  * Note 1. IP that starts with 169.xxx.xxx.xxx isn't valid functional IP.

  * Note 2. There could be an IPv6 entries too. However, they are not functional for Internet or LAN traffic. They are necessary for Win 7 homegroup special configuration.

  ---------------------------------------------------

  A message in the small window that says connected wireless doesn't means that you are really a valid functional connection.

  Above everything is OK, you must be able to connect to the router.

  Connection to the router means that you can enter the IP of the router base in an address bar in one go, being able to connect and configure the router menus see.

  If it doesn't connect to the router, journal newspaper from any computer that can connect to the router wirelessly with a wire, disable wireless security, make sure that the wireless SSID broadcast is enabled and try to connect with no. wireless security.

  Enable security wireless after you eat to make a functional connection.

  
  

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• My laptop does not connect to the internet. .

  My laptop does not connect to wireless internet.   All wireless drivers are in place, but it's like windows is be fooled into thinking that they are not there. A Trojan horse has been proposed, but I don't know what to do.  My ISP is also intrigued by this. Any suggestions would be welcome.

  Hello

  1. which browser is installed on the computer?

  2. do you get an error message?

  3. were there any changes (hardware or software) to the computer before the show?

  Method 1:  Perform the steps from the link below and see if it helps.

  Windows wireless and wired network connection problems 

  Method 2: Use the Microsoft Safety Scanner in full scan mode and remove all threats that is not detected by it and see if the problem persists.

  Microsoft safety scanner

  Note: the Microsoft Safety Scanner expires 10 days after being downloaded. To restart a scan with the latest definitions of anti-malware, download and run the Microsoft Safety Scanner again.

  The Microsoft Safety Scanner is not a replacement for the use of antivirus software that offers continuous protection.

  Hope this information helps.

• Linksys Router WRT160N - Wireless does not connect to the cable modem

  I installed the Linksys WRT160n router to replace an existing G router. When installed the new wireless router works, but the router does not receive a connection (IP address - look under status) of the cable modem (so no internet). When I reconnect the old router and then connect the new router, I get any internet connection through two routers (so the old dishes router the IP address that accepts the new router).

  I have configured the router N new for

  "Automatic configuration - DHCP", no need for connection, IP address dynamic, etc (as required by ISP - Timewarner)

  I tried to renewal and release IP address by the router N when it is connected directly to the main switch (the switch to connect to the cable modem). In so doing, shouldn't that assign a new IP address to the router?

  I am allowed 3 IPs from the cable company (because of the switch) and I use all three with three different internet IP cameras to each address for home security system.

  Any suggestions on why the router is not connecting to the internet? Do I need to reboot physically everything on the network, including the cable modem?

  If I understand your post, you said that your ISP gives you 3 Internet IP addresses and you have 3 cameras that use one of these Internet IP addresses.  If this is correct, then that leaves no IP Internet address for your WRT160N use - so that would explain why your WRT160N cannot get an Internet connection.

  If I misread your post, and you have an Internet IP address available for the WRT160N, you might have a problem with your modem and two WRT160N tries to use the same 192.168.1.x subnet.  To check this, follow these steps:

  (1) Please indicate addresses that use your cameras (IE before you take the test below).  If the addresses do not begin with 192.168, then erase the last half of each address.

  (2) Please indicate your ISP

  (3) Please indicate the make and exact model of your modem (not the WRT160N) number.

  (4) Please do the following test:

  Put your entire network.  Disconnect the switch (including cameras) to the modem.  Using an ethernet cable, connect your modem directly to your computer.  (Do not use the WRT160N for this test).  Turn on the modem and the computer.  Make sure you have an active Internet connection, then go ahead with what follows: (even if your Internet connection does not work, include this and move forward.)

  Go to 'Start' > all programs > Accessories > command prompt.
  A black DOS window will appear. Type "ipconfig/all" (with no quotes), and press the Enter key.   Copy all results in your next post.  To make the copy, highlight the results, and then use the keys copy (Ctrl-c) and paste (Ctrl-v) keys.  If your "IP address" does not begin with 192.168, then for security reasons, delete the latter half of your IP address.

• My laptop does not connect to the internet, even if the wi - fi connection is available

  OK, I have a netbook ASUS T-100 with windows 8.1. Yesterday, while I was downloading a game software, a notice came up saying "Windows Defender has blocked a program to run. I trusted the software so I went Windows Defender and allowed the program to run. But I discovered that the program could have the potential of harmful effects to other startup add-ons and programs download without my permission (even if during the installation of the software, I REFUSED any other unwanted programs being installed). So, I opened the Panel and uninstalled everything that has been downloaded.

  This is where everything started to go weird. I thought everything was fine until I tried to open Google Chrome on my desk.  He said something like 'cannot be opened because this application may have been moved or copied. Same for Internet Explorer. I went on the start screen and tried to open Chrome and IE, but there was no answer. Then I thought maybe restart the laptop would be useful. So I restarted. Worst decision ever. After the reboot, there is no Chrome or IE. They simply disappeared! I tried to look for them, but it did not help.

  I tried to download Chrome from the store, but it wouldn't connect to the internet (even if it was connected to my router). It showed an error «0x80072efd» I went Windows Network Diagnostics and tried to solve the problem, and something else end up - "the remote device or resource wont accept the connection". I looked on the internet and there are solutions saying to disable security. So I tried to turn off Windows Defender and firewall, but even once, that does not solve anything. One of the alternatives was to do a system restore, but I don't think that this is necessary, just?

  P.S. I have an iPod touch and a family laptop that connects perfectly with WI - FI. Thus, there cannot be a router issue...

  I DON'T KNOW WHAT DO YOU HEEEELLLP PLEASE! I have an assignment due next week and I need my netbook for IT... any help would be greatly appreciated...

  UPDATE1: I just noticed that the mail application still displays new messages, except the pictures of these mails are not displayed (they come with a cross). Does this help? #

  I FIXED IT! BY MYSELF

  so, for those of you who have a similar problem:

  what I did:

  1. realizes Change PC settings (from by clicking on settings of charms)

  2. click on network

  3. click Proxy

  4. off "use a proxy server".

  5 BOOM, internet s on the back.

  I have a question however, disabling proxy effect on my network connection? Like what is?

• My laptop Vista with Atheros AR5007 802. 11 b / g adapter does not connect to the internet using the local area or wireless network connections

  I just bought a new router d-link wireless n for my house.  Connect my Win 7 Desktop, laptop xp to Acer and multitude of other devices, but my laptop Vista with Atheros AR5007 adapter does not connect to internet.  I tried to disable IPv6, defining the name of the network, flushing dns cache, etc..  Nothing will work.  (It would not connect to an another 802.11n router in January either.)

  I get local only on both connections Wi-wired and wireless, no matter what I do.
  I'll send this to my office that I can not connect my laptop to the internet and he does not see the other machines on the network.
  Any suggestions from anyone?  I spent hours trying to solve the problems, now completely stumped.

  OK, here was my fix:

  I tried a lot of things, but they do not work.  I downloaded a 'new' driver of HP - it turns out it was the original with the problem.  I found another one that was about a more recent months, still does not work.  I finally managed to get the atheros.cz driver for my card files.  But they do not have an installation file.  I had to search for each old file in its directory, copy it to another place (to be sure, just in case) and then copy and replace the old file with the new file in the original folder.  Fortunately, there were only 6 files, but it took about an hour and a half.  This isn't a lot of time compared to the 18 or if I was just trying to figure out the problem.  Now, my laptop connects to the internet without problem.
  I had this problem with a router "n" beginning of the year in a hostel.  The guy in the Inn told me that he had seen before once.  It's obviously a common problem with these cards (as seen on the "solutions" online) and Vista.  I'm always hating on Vista after this problem.

• Router WRT54G does not connect to the internet during the passage of the modem cable to fios buildings

  I recently had need save money and cut off my cable service. Fortunately my building has a service that they lead in all apartments. It's just an ethernet wire that runs into my apt... (I pay for it with my mainentance). The router linksys has worked with the cable modem, but as soon as I plug the service buildings (i.e. Fios) it doesn't let me go on the internet. If I hang the service buildings until dirrectly on my Vista PC or Mac OS 10, it works fine but as soon as I set up the router I get an unable to connect to the internet message on Firefox, IE and Safari.    Ive updated the ware closes on it and Ive reset router noumerous times. IM at a loss.   Would appreciate any help.

  Probably, you will need to reconfigure your modem. Here is the procedure.

• My laptop does not connect to the Internet wireless or Ethernet.

  Hi my laptop does not connect to Internet via Wi - Fi or Ethernet connection. He previously connected the two. The model is a portable HDX-18 1201 and runs the Windows Vista 64-bit operating system. I have had the laptop for a while now and this is the first time that this has happened. I tried to locate the network drivers but can't find them on the Device Manager. To my knowledge, I have not changed anything on the computer that may have caused this. If someone could help it would be greatly appreciated. Thanks Richard

  Hi Richard,

  Search for the latest drivers for your model laptop from the HP site and then try if operate you, install it, for the wireless and Ethernet cards

  just download the drivers from the HP website through another computer, copy it to MemoryStick and install the drivers on your laptop and see if it detects it fine, and then it should work Fine.

  Kind regards

  Amjad