Router WRT54G does not connect to the internet during the passage of the modem cable to fios buildings

Similar Questions

• My HP shows it is connected to the new router, but does not connect to the internet. How should I do?

  I have a HP G60 Notebook PC with Windows Vista Home Premium, it is about 4 years old. I recently got a new Cisco Linksys E1500 wireless router, which is connected to my home computer. My laptop shows that it is connected to the home network, but it does not connect to the internet. Other laptops in the House are able to connect to the network and to the internet. Mine seems to be the only one not working do not. Why it is not working? What should I do about it?

  I ran the network diagnostics. It is said "a problem with you network router or modem broadband could prevent an internet connection." I have disconnected these two and tried again. It did not work! I have also connected my laptop directly on the modem and it does not always connect to the internet. I tried to reset the network card. My IP settings are set to automatic.

  My internet connection was not a problem before last week (when I got a new router). What is the problem with my computer? Help, please!

  Hello:

  If you have an Atheros wireless adapter in your PC and you have not updated the driver, I recommend that you install it.

  http://h20000.www2.HP.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=321957&prodSeriesId=3688868&swItem=ob-99392-1&mode=3

  Wireless adapters Atheros with former pilots, dislikes the new Linksys routers.

  If you have an Atheros wireless card, and your wireless driver is more than 2 years, I am very confident that this will solve your connection problem.

  Paul

• N300 EX2700 does not connect with the modem

  Trying to install EX2700 N300 range extender, but the link never seeing device, not with modem connection. I even hung it with cables ethernet right now, and it still does not connect. Any suggestions?

  No, he didn't. But a few days later, a wi - fi network "Netgear_ext" appeared in my ads. I started playing with it, then I could access the Web activation page. I still don't know how I did it, but eventually it worked, and he has now set up and solved my lack of power of the signal of the TV farthest from the router.

• Installation of Windows 7 does not connect to the modem broadband.

  I installed characteristic of two different versions of Win 7 64 on my desktop at different times.

  The two does not connect to my modem. I get error 651. I've tried everything.

  I have consulted my ISP, checked the provider. The installer works fine with other OS and Win 7 on another computer.

  My office tells me that there is no driver installed. There is no driver to install.

  I need a connection to the firmware in the modem to work, something that seems missing from Win 7 Home Premium 64.
  Your background of catch-22
  LCW

  See this previous post/answer

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-networking/error-651-in-Windows-7/65077414-15f8-450b-BD19-5cce9a57fcf0

  PS after I clean installed did you get your motherboard manufacturer system drivers, if a generic desktop computer, or if from a major manufacturer, for example Dell/HP support site?

• G70 213EM Windows 7 Fax does not connect to the modem

  "Hi, my G70 213EM let me use Windows 7 Fax, when I try to send a fax, it tries to detect the modem (HDAUDIO Soft Data Fax Modem with SmartCP) and reportsan error occurred - try the operation later or contact your system administrator '. He has worked with the release candidate, but not now with Windows 7 Home Premium full version.

  I questioned the modem via Device Manager and obviously only the fault I can see is a line in the newspaper that says ' DSR is low during the initialization of the modem. Verify the modem is turned on ' , but it responds after that? very strange.

  12-01-2009 09:34:12.373 - File: C:\Windows\system32\tapisrv.dll, Version 6.1.7600
  12-01-2009 09:34:12.389 - File: C:\Windows\system32\unimdm.tsp, Version 6.1.7600
  12-01-2009 09:34:12.389 - File: C:\Windows\system32\unimdmat.dll, Version 6.1.7600
  12-01-2009 09:34:12.389 - File: C:\Windows\system32\uniplat.dll, Version 6.1.7600
  12-01-2009 09:34:12.404 - File: C:\Windows\system32\drivers\modem.sys, Version 6.1.7600
  12-01-2009 09:34:12.404 - File: C:\Windows\system32\modemui.dll, Version 6.1.7600
  12-01-2009 09:34:12.404 - File: C:\Windows\system32\mdminst.dll, Version 6.1.7600
  12-01-2009 09:34:12.404 - Modem type: HDAUDIO Soft Data Fax Modem with SmartCP
  12-01-2009 09:34:12.404 - Modem inf path: oem3.inf
  12-01-2009 09:34:12.404 - Modem inf section: ModemX
  12-01-2009 09:34:12.404 - Matching hardware ID: hdaudio\func_02&ven_14f1&dev_5051&subsys_103c360b
  12-01-2009 09:34:12.600 - 115200,8,N,1, ctsfl=1, rtsctl=2
  12-01-2009 09:34:12.600 - Initializing modem.
  12-01-2009 09:34:12.600 - DSR is low while initializing the modem. Verify modem is turned on.
  12-01-2009 09:34:12.610 - Send: AT
  12-01-2009 09:34:12.611 - Recv: OK
  12-01-2009 09:34:12.611 - Interpreted response: OK
  12-01-2009 09:34:12.621 - Send: AT&FE0V1S0=0&C1&D2+MR=2;+DR=1;+ER=1;W2
  12-01-2009 09:34:12.623 - Recv: OK
  12-01-2009 09:34:12.623 - Interpreted response: OK
  12-01-2009 09:34:12.633 - Send: ATS7=60S30=0L2M1+ES=3,0,2;+DS=3;+DS44=3;+IFC=2,2;X4
  12-01-2009 09:34:12.634 - Recv: OK
  12-01-2009 09:34:12.634 - Interpreted response: OK
  12-01-2009 09:34:12.635 - Session Statistics:
  12-01-2009 09:34:12.635 -                Reads : 18 bytes
  12-01-2009 09:34:12.635 -                Writes: 94 bytes
  ATQ0V1E0 - OK
  AT+GMM - +GMM: HDAUDIO Soft Data Fax Modem with SmartCP
  AT+FCLASS=? - 0,1
  AT#CLS=? - COMMAND NOT SUPPORTED
  AT+GCI? - +GCI: B4
  AT+GCI=? - +GCI: (00,01,02,03,04,05,06,07,09,0A,0B,0C,0D,0E,0F,10,11,12,13,14,15,16,19,1A,1B,1C,1D,1E,1F,20,21,22,23,24,25,26,27,28,29,2A,2B,2C,2D,2E,2F,30,31,32,33,34,35,36,37,38,39,3A,3B,3C,3D,3E,40,41,42,43,44,45,46,47,48,49,4B,4C,4D,4E,4F,50,51,52,53,54,55,56,57,58,59,5A,5B,5C,5E,5F,60,61,62,63,64,65,66,67,68,69,6A,6B,6C,6D,6E,6F,70,71,72,73,74,75,76,77,78,79,7A,7B,7C,7D,7E,7F,80,81,82,83,84,85,86,87,88,89,8A,8B,8C,8D,8E,8F,90,92,93,94,96,97,98,99,9A,9B,9C,9D,9E,9F,A0,A1,A2,A3,A4,A5,A6,A7,A8,A9,AA,AB,AC,AD,AE,AF,B0,B1,B2,B3,B4,B5,B6,B7,B8,B9,BA,BB,BC,BD,BE,BF,C1,C2,C3,C4,C5,C7,C8,C9,CA,CB,CC,CD,CE,CF,D0,D1,D2,D3,D4,D5,D6,D7,D8,D9,DA,DB,DC,DD,DE,DF,E0,E1,E2,E3,E4,E5,E6,E7,E8,EA,EB,EC,ED,EE,EF,F0,F1,F2,F3,F4,F5,F7,F8,F9,FA,FB,FC,FE)
  ATI1 - 255
  ATI2 - OK
  ATI3 - SoftK56V_B2.1_V7.80.4.50
  ATI4 - HDAUDIO Soft Data Fax Modem with SmartCP
  ATI5 - 180
  ATI6 - SoftK56
         CModem Version 12
         Rksample Version 342
  ATI7 - 255
  

  I hope someone can help?

  Re-installation of Windows 7 Home Premium 64-bit and let it update seem to have solved this problem, don't know why?

  Thanks for your help anyway.

• I am using windows 7 and my computer laptop wifi does not connect to the modem. It worked correctly with the other modems. I had the prob with the new modem provided by optus. can someone help me please?

  my computer laptop wifi works with other modems. and my modem works with other laptops. they have one problem with each other.

  I don't know why, please help me...

  Hello Omar.

  Thank you for keeping us posted.

  It seems that you did not try the method 2 and 3 after running the troubleshooter from network. Please, try it both ways and see if that solves the problem.

  Reply with the results. We will be happy to help you.

• I just installed a new router and now my desktop running Windows XP computer does not connect to the internet.

  Hello

  I just installed a new router and now my desktop running xp computer does not connect to the internet. I know that it is not the router because I plugged the cable into my laptop running 7 and it works fine. When I try to dhcp I get 169..., when I put manually the IP just get no access to the internet and can not ping to the router address. I tried to run the net work Assistant, emptied my dns, disabled all firewals, still nothing.
  Any suggestions?
  original title: connectivity Limeted

  The zero configuration utility works very well. But it is a desktop computer and on cable. All other wired and wireless PC in the office is working well, then it's definitely this PC. He came out of nowhere, I install a network printer on the PC but that's all.

  Your messages are a bit terse, but if I understand correctly

  • You have a router connected to the Internet and multiple computers connected to the router, some Ethernet cable and others by wireless.
  • All but one of these computers can reach successfully from the Internet via the router.
  • A computer that can't browse the Internet is connected to the router via an Ethernet cable.
  • You disconnected the cable between the router and the desktop problem and connected it to a Windows 7 laptop and the laptop connected to the Internet via the router.
  • You haven't seen any error message (except, perhaps, a message on "Limited or no connectivity").
  • You have installed Windows XP Service Pack 3 (or at least Service Pack 2)

  Assuming that all the foregoing is an accurate summary of the situation, I suggest that you do the following:

  Open a command prompt window (start > run > cmd > OK)
  Type the following lines and press ENTER after each line

  Netsh reset winsock catalog
  netsh int ip reset c:\resetlog.txt

  Close the command prompt window and restart the computer.

• I installed a new router (Netgear N300) wireless and my laptop is the only computer that does not connect to the internet.

  Connected to the new router, but locally only.

  Currently, I installed a new router (Netgear N300) wireless and my laptop is the only computer that does not connect to the internet. The small icon to the left of my screen says only: ACCESS: LOCAL ONLY.
  BASICALLY,.

  I have Windows Vista Home Premium, notebook Compaq (Presario CQ60 to be exact)

  I can connect if I use a cable, but its disadvantages.

  I can connect wirelessly with my PC and Ipad. and Internet access.

  I TRIED:
  Various patches microsoft such as resetting TCP, safe mode with network, reset the router. »

  Thank you in advance and we hope you can answer this soon!

  I use an Atheros AR5007 802. 11 b / g WiFi Adapter(Compaq laptop) for the moment so this is useful. Thanks again!
  Someone suggested that I update my wireless driver. I am open to this idea, if anyone can find a safe and legal site with the download.

  Hi Bryyaan11,

  You can check out the link to HP support and try to download the drivers for your wireless card updated:

  Support HP & drivers

  For more information, you can also consult the following article:

  Updated a hardware driver that is not working properly

  You can also check the following items and try the steps:

  Windows wireless and wired network connection problems

  Solve problems, find wireless networks

  Hope this information is useful.

• Laptop does not connect to the internet, office. Both use the same router. Tried troubleshooting, does not. Help!

  I have a desktop computer and a laptop. Both use the same router. The laptop does not connect to the network, but the office has no problem. My wireless adapter on the laptop is on, I tried troubleshooting. I tried to turn it off for 30 seconds then restart him. But nothing is resolved the problem. Any ideas would be helpful! Thank you

  Hello

  Maybe this can help.

  These steps and tell us where is the breaking point.

  Check the Device Manager for the wireless card valid entry.

  http://www.ezlan.NET/Win7/net_dm.jpg

  If there is no valid entry, remove any entry from fake and re - install the drivers for the wireless card.

  Check network connections to make sure that you have a network icon/entry wireless connection, and that the properties of the icon (right-click on the icon) are correctly configured with the TCP/IPv4 protocol in the properties of network connections.

  http://www.ezlan.NET/Win7/net_connection_tcp.jpg

  Make sure that if there is Wireless Utility a utility vendor is not running with the native Windows wireless utility.

  ----------------

  Make sure you firewall No. preventing / blocks wireless components to join the network.

  Some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible set up the firewall correctly, otherwise totally uninstall and get rid of its remaining processes that permit the own local network traffic flow.

  If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  ---------------------------

  Stack TCP/IP work should look like.

  Right-click on the wireless network connection card, select status, details and see if she got an IP address and the rest of the settings.

  http://www.ezlan.NET/Win7/status-NIC.jpg

  Description is the data of the card making.

  The physical address is MAC of the card number.

  The xx must be a number between 0 and 255 (all xx even number).

  YY should be between 0 and 255

  ZZ should be between 0 and 255 (zz all the same number.)

  The date of the lease must be valid at the present time.

  * Note 1. IP that starts with 169.xxx.xxx.xxx isn't valid functional IP.

  * Note 2. There could be an IPv6 entries too. However, they are not functional for Internet or LAN traffic. They are necessary for Win 7 homegroup special configuration.

  ---------------------------------------------------

  A message in the small window that says connected wireless doesn't means that you are really a valid functional connection.

  Above everything is OK, you must be able to connect to the router.

  Connection to the router means that you can enter the IP of the router base in an address bar in one go, being able to connect and configure the router menus see.

  If it doesn't connect to the router, journal newspaper from any computer that can connect to the router wirelessly with a wire, disable wireless security, make sure that the wireless SSID broadcast is enabled and try to connect with no. wireless security.

  Enable security wireless after you eat to make a functional connection.

  
  

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Router is not connecting to the modem so I can't get internet

  All right-_ - I tried a lot of things with this so I get irritated sorry. Here is my info I have a Linksys Wireless Router with SpeedBoost Firmware Version 7.2 WRT54GS (latest version). I'm trying to use it with a Sprint 645 series Modem. My IP address when you are connected to the router and the router connected to the Modem is 192.168.1.100 who my ISP said was ok to make it work. While it is just connected to my modem, it's the same thing except replace the 100 by 1. My ISP uses a measure of security where The Thing DHCP is 192.168.1.1 and so is the DNS server and default gateway and im not sure if this has something to do with it. I used the ping at a command prompt to make sure that I am connected to the router when its plugged up and it is. This is a new router. I have internet with Modem just perfectly. I tried to reset the router and that does not work-_-. I don't think it is important more because I tried to fix the many way people have told me and it didn't work, but I'll tell u in any case. When I put up the first router time I hung and lit everything at the beginning. Then I noticed that it says Run CD before to connect the cables... those who were not in the instructions but wtv... anyway resetting should have fixed or so I was told by other people on this forum. I use a laptop with Windows Vista, and I don't have access to a desktop computer in case I need a XD. I can connect to the router fine because I can access the Setup page... and I can connect wireless... The ONLY problem seems to be that the router will not connect to the Modem... for some reason of wtv-_ - I think that its because the entire security measure on the way to the DHCP and the DSN and the bridge are all 192.168.1.1, but that's just me. I'm sorry this is very long but I really want this problem-_ - I had this router for a month and becomes really annoying so please help . My ISP is Embarq. I ran the installation CD and I had all through the last step (standby router) after having connected the power supply to the wall for the router. Just, it is there forever and then says "error: 322 cannot find router or something like that." There are 3 steps to try to fix it. It says to make sure that the router is connected (it is), it is said also to make sure that u does not actually connect your old router, (I don't have a-_-) and then re-run Setup. and by the installer, I mean where u plug in all the cables in the right way. * sigh *.

  If you need anything else please ask.

  Your second post says "" ignore this "so I guess everyone thought that you set..."

  When you connect through your router that you have two instances of DHCP past... one is your DSL modem with router IP address on its WAN interface. The other is the router that gives your computer an IP address via the DHCP server on the router. The IP address of the modem gives your router is in the 192.168.1.0 network. Unfortunately, by default, the reange of Linksys routers LAN IP address is also in this range. For that to work, you must set your router 192.168.2.1 LAN ip, so that the LAN and WAN router interfaces are in different networks.

  To do this, unplug the DSL modem router, power it and your computer, and then connect the computer to the router by an ethernet cable. Turn on the router and the computer, and then go to 192.168.1.1. Change the LAN IP on router 192.168.2.1, save the configuration, and then restart the computer. Once the computer returns to the top, navigate to 192.168.2.1... you should be able to get to the router GUI configuration.

  Turn off the router and the DSL modem, connect the router to the modem via the Internet port using an ethernet cable, and then turn on the modem, then the router... you should be good to go...

• Airport utility: green points on the AirPort Extreme & Internet; Mini Mac does not connect to the internet.

  Airport utility shows green points on the AirPort Extreme and the Internet, but my my Mac mini does not connect to the internet. IPhones and 2 portable Windows connect very well, and see all the devices on the home network. The problem occurred after that PSI has swapped an ancient for a Comtrend CT5072T DSL modem. I tried to stop and things start back up as if the installation of the internet for the first time. No joy.

  The airport connects using DHCP in Bridge Mode

  The router address is 192.168.80.1

  Address IPv4 is 192.168.80.2

  DNS server is the same as the router, but grayed out

  Mac Mini IPv4 Address is 192.168.80.3

  IPv6 automatically configures

  Also updated the firmware of the airport; no change.

  ISP guy was friendly but puzzled. He started at the top floor level Tech, so I do not know when I hear back.

  Any ideas to fix?

  Thank you.

  Post edited by: en maschera

  but my my Mac mini does not connect to the internet.

  The problem occurred after that PSI has swapped an ancient for a Comtrend CT5072T DSL modem.

  Hello

  Network preferences may be damaged.

  Open the Finder. In the Finder menu bar, click go > go to folder

  Type or copy paste the following text:

  / Library/Preferences/SystemConfiguration

  Click OK, and then move all files in the SystemConfiguration folder to the trash.

  Restart your Mac. See if that makes a difference.

  Your Mac will generate a new SystemConfiguration folder for you.

  Then open AirPort Utility located in HD > Applications > Utilitiies

  Make sure that both Internet and Extreme are green.

  

• Atheros AR9285 in CQ61-410US wireless network card does not connect to the Internet after the update of the adapter driver

  I have a Compaq Presario CQ61-410US (WA974UA) which is equipped with an Atheros AR9285 B/G/N wireless network adapter.   The laptop Internet access was fast and stable when using a Wi - Fi N.   Its pilot AR9285 was the initial version of the 8.0.0.172 factory.  But because there were so many subsequent driver updates, I've updated the display driver version from the support page 8.9.9.316 (sp48755.exe).  However, after updating the driver, I immediately lost Internet access.   The laptop is running Windows 7 Home Premium with Service Pack 1 and 64-bit.

  The driver seems to be installed OK, but it does not connect to the Internet.  Here is the status of the driver: 1) in Device Manager it appears OK and is presented as working properly.  (2) in the results of IPCONFIG/all, it there is no entry for the wireless adapter and without IP addresses are affected.  Here are the results of the IPCONFIG/all command:

  C:\Users\Karen>ipconfig/all

  Windows IP configuration

  Name of the host...: KarensLaptop
  Primary Dns suffix...:
  Node... type: hybrid
  Active... IP routing: No.
  Active... proxy WINS: No.

  Ethernet connection to the Local network card:
   
  State of the media...: Media disconnected
  Connection - a DNS suffix is specific. :
  Description...: Realtek PCIe FE Family Controller
  Physical address: 00-26 - 9th - JJ - 83 - 9 c
  DHCP active...: Yes
  Autoconfiguration enabled... Yes

  Tunnel adapter isatap. {E52D6F3E-5080 4B3B - 8BE7 - B7CFD7E137D1}:

  State of the media...: Media disconnected
  Connection - a DNS suffix is specific. :
  ... Description: Microsoft ISHTHP adapter
  Physical address: 00-00 - 00 - 00 - 00 - 00 - 00 - E0
  DHCP active...: No.
  Auto connection...: Yes

  Map of tunnel Teredo Tunneling Pseudo - Interface:

  State of the media...:...: media disconnected
  Connection - a DNS suffix is specific. :
  ... Description: Teredo Tunneling Pseudo - Interface
  Physical address.... : 00-00 - 00 - 00 - 00 - 00 - 00 - E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  C:\Users\Karen >

  (3) Trying to Connect through connections network does not a list of known available networks and instead says "not connected - no connection is available."

  I have read several messages from the HP Forum and tried a lot of things, including the installation of various updates driver later thanks to the version 10.0.0.222, but I still can't the driver to connect to the Internet.  I also changed my router "n" has only B/G as the AR9285 pilot has a history of problems with Wireless N.  Even back to the original driver version 8.0.0.172 provides an Internet connection.

  Any advice would be appreciated.

  Hello:

  I'm glad that you were able to restore your internet connection.

  I'd go with the latest driver HP vice one from another source.

  The only time wherever I go outside HP for wireless network drivers is if you have an Intel wireless card.

  My recommendation is to use the free MS Security Essentials antivirus/antispyware, which never interfere with how "things important works" on your PC, such as network connections.

  http://www.Microsoft.com/en-US/Download/details.aspx?ID=5201

  Your router with a hardware firewall and a software firewall Windows. I don't see the importance of adding other firewalls.

  Unless you have a lot of albums secret info on your PC that pirates would like to get my hands on, these fully functional security roadblocks are adequate for most of us.

• My desktop under Vista Home Premium does not connect to the internet.

  I have an Acer Aspire X 1200 desktop equipped with a NVIDIA NForce network controller. About 1 week ago I was browsing the internet, Norton anti-virus popped up and told me to renew my subscription. Now, I've never had Norton on my computer and when you click Remind Me later, my internet crashed. Now the whenever I plug my ethernet cable in the box, it connects to my router Motorola 5BS101 surfboard, but it does not connect to the Internet. I am running Windows Vista Home Premium. I tried to run malware programs remover, thinking it was a malware, nothing done. I tried to run to remove virus and nothing. I tried to change the IP address to my my laptop was broadcasting, because the internet runs on it, but no results. When using the command prompt to find out what the problem is, it says the active IP routing: routing WINS unactivated: No. looking at the stats of network adapters, it says active DHCP: No. address IPv6 local link: fe80::15f9:58e2:c2d8:66e7 10%
  Autoconfiguration IPv4: 169.254.102.231. Also using ipconfig / renew, said the message DHCP is not enabled.

  Are you sure you never had a Norton trial subscription on your computer?

  Norton will do strange things.

  http://www.Symantec.com/Norton/support/kb/web_view.jsp?wv_type=public_web&docURL=20080710133834EN

  Try to use the Norton removal tool.

  The computer you are using now if you have an Internet connection with the other > download / save > copy to Flash Drive > transfer / install it and launch it on the other computer.

  See you soon.

  Mick Murphy - Microsoft partner

• HP Photosmart D110a does not connect after the software update of the router

  I'll try a restatement of my first message:

  Two days ago I had problems with my Internet service provider modem.  This problem has been solved, but leads to a second problem still does not connect to the internet.  Then with the help of technical support D-Link, an update of the software has been downloaded to my wireless router and installed and now I can connect to the internet.

  But today, I had to use my printer/scanner for 2 1/2 year, HP Photosmart D110a, it is not connected through the above wireless router.  (The blue light on the printer blinks just).  Tech support says I'm out of warranty, so I hope someone can help me here on this forum.

  Thank you!

  Glad you got it to work, please mark it as Solution accepted so that others can search and find the answer too.

• Homer in Windows Server does not connect to the internet.

  I installed Windows Home Server on a self-built media server. Everything on the hardware is working properly. The server software is installed. The ethernet line is connected to my Linksys router. The power light is on decision-making on the case ethernet connection. The power led is on the router where the ethernet is connected. So, in my view, that the issue is not material.
  Problems:
  1. the server does not connect to the internet.
  2. my computer does not recognize the server when I install the Windows Home Server Connector software.
  3. the wizard of Linksys on my computer does not recognize the server as a "new device".

  I feel like I'm missing a driver, maybe a driver of ethernet controller, but do not know how to diagnose the problem.  I downloaded the Windows tool that identified the problems I listed, but solutions are not feasible.

  Any suggestions?

  Hi Mikey1947,

  You can check this link, try the suggestions provided and check if that helps

  http://social.Microsoft.com/forums/en-us/whsfaq/thread/15a9e657-54a3-453F-B0E7-1efa59b7feea

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.