My PC has a black screen on normal mode

Similar Questions

• Computer has a black screen with a message "power off, then reinstall the jumper in normal mode position."

  Original title: black screen?

  My computer has a black screen with: turn off power and reinstall the jumper in normal mode position? Help!

  Hi Miguel C.
   
  a. What is the brand of your computer?
   
  b. do you remember of any changes to your machine before the question?
   
  I don't know what motherboard you have, but some is shipped with the 'Clear CMOS' jumper in the position unequivocally. Check the manual of your motherboard for this rider and make sure that it is in the normal position.
   
  J7B1 computer configuration jumper block requires a single rider set the configuration of the BIOS Setup utility. This allows the configuration in the configuration utility BIOS, including the frequency of bus and the processor motherboard speed.
   
  Note: Do not move this jumper with the computer turned on.
  
  Warning of the BIOS:
  BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.
   
  I think, you'd be best to contact the manufacturer of the motherboard as this seems to be a motherboard problem.
   
  Aziz Nadeem - Microsoft Support
   

  [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

• IdeaPad 500 - a black screen during Normal labor

  IdeaPad 500 - a black screen during Normal labor

  My 500 Ideapad is a month old. After a few days with her, I saw that in the middle of my normal work (Word, Excel, ETC...) My screen turn Black and will never go back. Only with the black screen reboot goes normal again.

  What should I do here?

  Thank you

  In response to the reports of customer displays or screens turning off on Lenovo while in use systems and works on battery, Lenovo released a solution via the Intel Management Engine Firmware update, v.11.0.0.1176.

  The Intel Firmware has been approved for the following models:

  • IdeaPad 300 s-14ISK, 500-14ISK ideapad
  
  
  • Lenovo Edge-2-1580
  
  
  • Lenovo, Flex 3-1480, Flex 3-1580,
  
  
  • 500-14ISK, 500-15ISK Yoga Yoga

  Firmware Intel ME can be downloaded here: http://support.lenovo.com/us/en/downloads/ds105001

  If the solution provided by Lenovo does not resolve the problem for you, other customers report that a workaround solution provided by the MattDN93 client also solves the problem. More information on workaround can be found here: https://forums.lenovo.com/t5/Lenovo-IdeaPad-100-305-500-Edge/Flex-3-screen-turns-off-when-working-on...

  Thank you

• HP Compaq has a black screen at power up... The BIOS Corruption failure?

  I have a Compaq Presario CQ61 product: VM9496Q2X model: CQ61-319WM series: [edited by moderator serial number], which has a black screen when I turn on.  The wifi button stays red and the caps lock flashes twice.  I think that it indicates a BIOS curruption faliure.  I tried to reset by unplugging and removing the battery and holding the power for 30 seconds button.  I tried the f8 key and esc repeatly to power upward. I also tried pressing the windows and the B key and the power key, but nothing has worked.  Any help would be greatly appreciated!

  I'm very disappointed with the lack of response of an HP Service Technician.  I ended up taking my laptop to a computer repair shop.  My problem is that the graphics card has become dessoudée of the motherboard.  They have rearranged my motherboard and it works fine.  fix $ 79.00.

• I hope someone can help.my p7-1054 has a black screen

  I hope someone can help.my p7-1054 has a black screen

  Hello

  Follow the steps listed in the link below

  http://support.HP.com/us-en/document/c01896806

• My computer has a black screen and a cursor and there is no menu start more

  Original title: replay Vista operating system

  What I would like to know, is my computer only has a black screen and a cursor, there is no menu start, so I can stop and start a new installation of windows vista? If anyone can help please. I thank you very much for your time and have a fantastic day. Shawn

  Hello

  What changes have been made on your machine for there to be a black screen with a cursor?

  Rather than doing a clean install of your operating system, I suggest you do the following.

  Step 1:

  Remove all external devices (printer, USB flash drive), as appropriate, and start your computer again and check.

  Step 2:

  If this is little help, start your machine in safe mode and check if it starts on the desktop.

  Let us know the status of the issue.

  Azeez Nadeem - Microsoft Support [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

• My computer takes 20 minutes to start and also has a black screen

  Hello world

  I have a Dell Dimension 9200 and recently every time I start my computer or it reboot, it takes 20 minutes to get to the desktop and also has a black screen. This issue has occurred only recently and I don't know what is the cause and so advice would be welcome.

  Other strange things include all my system restore points are missing and so I can't return the operating system to a previous date when it was working properly.

  And when I did a test on the hard disk, one of the internal drives have had a "Fail" result - Code 7 back. I don't know if this was caused by a virus or is the result of a mechanical failure in the hard drive itself.

  Thank you very much.

  Gordon

  

  Bev.

• Black screen after the mode 'sleep'

  My laptop never wakes fashion "Eve" and just keep with the dreaded black screen.

  If anyone has had this problem or have solutions?

  I am currently using a hardware, operating system.

  This message can help,

  http://h30434.www3.HP.com/T5/notebook-lockups-freezes-hangs/Pavilion-DV6-black-screen-after-sleep-mode/TD-p/527033

• Computer has a black screen and does not show the normal startup logo and more

  The computer that I use usually works well, until the next day, the day that I used it, ruined everything. My computer shows not the Windows 7 logo normal at startup, but instead, a bar with green lines in movement like the ones you see in older versions (Windows Vista), but now only the bar and did no logo in it and after starting does not display. It shows a completely black screen, but it makes a noise like the sound when she welcomes you to Windows 7. I tried safe mode and disabled the NVIDIA GeForce GT 220 graphics card and the screen works, but he is stuck at 800 x 600. In addition, the start screen is always the bar. How can I fix it? (Tried updating the gpu but still displayed black screen)

  Hello Rafael,.

  Thanks for posting your question on the Microsoft community.

  We need more information about the issue so that we can help you better.

  What is the brand and model of your computer?

  Thank you for details on the issue.

  This problem may occur because of corrupted display driver.

  I suggest to start your computer in safe mode, uninstall the display driver, restart your computer in normal mode

  mode and update driver from the website of the manufacturer of the computer display.

  Please see this link:
  Why my screen is black when I start Windows 7?
  http://Windows.Microsoft.com/en-us/Windows7/why-is-my-screen-black-when-i-start-Windows-7

  Important notes:
  Serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
  http://Windows.Microsoft.com/en-us/Windows/back-up-registry#1TC=Windows-7

  When you use system restore to restore the computer to a previous state, the programs and updates that you have installed are removed.

  I hope this information helps.

  Please let us know if you need more help.

  Thank you

• Satellite A100 has a black screen and will not charge in the Bios

  I bought a Satellite A100 - (model psaa8c-0fh00e) about 5 months ago. It was left overnight, which is not uncommon, and when I came back using about 15 hours later it was just a black screen. moved from the touch screen and keys, and nothing did. so I cold it starts and he died. I then turned it back as usual and the laptop turns on but the screen is completely black. It's not loading the normal Toshiba Bios screen.

  Now my question: If there is any way I can solve this, I am familiar with computers and parts. I don't get this cause I've ever had to reflash the wood or something like that. I am unsure of how to activate and I really want to have to take it to a shop, any suggestions would be helpful.

  Thanks in advance.

  Hi Conrad,.

  If your 100 starts normally (spinning HARD drive, optical drive LED flashes, fans turn etc.) then I suppose that your FL inverter or LCD screen is not. You can check this by connecting an external monitor to the laptop to see if it shows the normal display.

  On the other hand if there is no activity at all portable computer turn when you turn it on then I guess you have an internal hardware failure, possibly the main card, which must be checked by a Service partner authorized Toshiba since the unit is still under warranty if it is only 5 months old.

  Kind regards

• HP Pavilion 8 Windows: my hp pavillion windows 8 has a black screen after I put my password in

  After i.put my.password in expenses n then goes to a black svreen. I have tried f11, taking battery, reboot, close to the bottom.., .nothin works... Please.Help

  Hello

  Try the following.

  Boot the computer normally and log.

  Black screen, old the ctrl and alt keys and press delete.

  Select Task Manager.

  Click on file and select the new task.

  Type rstrui - also enter a tick in the box for "create this task with administrative privileges" - and click on Ok.

  When the system restore interface is loaded, choose a restore point at least 48 hours before the log - it occurs first and then proceed to the system restore.

  Kind regards

  DP - K

• Sony Vaio Vista has a black screen after update

  Hello. I have a sony vaio, I did an automatic update on shut down yesterday and now my computer will not boot even upward. It lights up with a mouse cursor and black screen and stays like that. It does the same thing with the recovery disk in as well. any help is welcome.

  Hello

  You can try these methods:

  1st thing to try is a restoration of the system in safe mode

  http://www.windowsvistauserguide.com/system_restore.htm

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode option with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  If that does not read this information

  the link below is how to download and get a vista disk startup repair, which you can start from the

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  Here's how to use startup repair system restore command prompt, etc. to bleepingcomputers link below

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  to boot from the dvd drive to be able to you will see a way to get into the bios Setup at the bottom of the screen or command menu start

  It would be F2 or delete etc to enter the BIOS or F12 etc. for the start menu

  Change boot order it do dvd drive 1st in the boot order

• After my computer will crash does not start has a black screen with message operating system not found. Responsible for recovery disc but wont start.

  not boot Vista after that computer crashed have a black screen with message operating system not found.recovery discs won't load

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

  Above is the way you normally boot from the Vista recovery disks.

  If you have tried to boot from the recovery without success disks, contact the manufacturer of your computer.

  This isn't their recovery process, Microsoft.

  See you soon,.

  Mick Murphy - Microsoft partner

• problems of Crysis 1 has No black screen now.

  I've seen a lot of answers to questions indicating that crysis 1a given accidents to black screens on different o.ses that I had windows 98 XP and Vista and my copy of crysis 1 never gave me a problem unless I used too resouluton that my graphics card could not overcome. So its fustrating it seems that anwser people see that it may have something to do with the fact that the crysis 1 submits this list operating systems to start up will not have windows 7 or the latest graphics cards. I am however trying to operate live 9 and with windows compatatbility for xp service pack 2 and 3 becaused I liked X.P more. I would get an arrested response and a .dll D3d10 fault as if I was running in vista. Now, I know that windows 7 is live 11 my video card is a 10 live and my motherboard is evaluated to opporate windows 8 could this be a problem every thing should be for x 11 direct., or you see something wrong with this system.please help someone.

  radeon HD 6750 video card of

  ASUS M5A99FX motherboard

  Windows 7 Professional operating system

  processor FX4100

  OK - I quote your new thread, so I can read all the information on one page - stick with a wire on a single topic in the future. It avoids the confusion and repetition of the suggestions.

  «I tried everything everyone else has, it just that someone has said that there crysis1 and can play on a 32-bit windows system.» It does not say something on his record or how he got that works perfectly, I guess it's the only one who says it works in 32 bit, all others, say if he to work ultimate 64 bit, why does. I'm using windows 7 32-bit professional. Oh, also instead of use oide im using A.C.H.I put sata up.in my bios it would have something to do with it. IM is not running in parrellel but serial.data flow. »

  Nothing to do with AHCI, 32 vs 64-bit or your motherboard is compatible Win8.

  «However trying to boot into 9 direct mode and with windows compatatbility for xp service pack 2 and 3 becaused I liked X.P more»

  Compatibility mode does not make Win7 run like XP.  In addition, it is not for you to determine which
  appropriate compatibility established by your bias towards XP.  Use what works.
  A strange thing with this game is it will run in 32-bit mode with no compatibility setting, but requires a consistency when using the 64-bit .exe - I use Vista sp2 with 64-bit .exe.

  "I would get arrested response and a .dll D3d10 fault as if I was running in vista".

  You choose the game settings are what determines if the game uses DX 10 not the operating system.
  Some of the very high settings are DX 10. When the gpu is not capable of DX10 these options would be
  not be available.
  Vista is the first to use DX10 and Win7 is first of all to use DX11 does not mean that they use also
  DX9. Check your System 32 folder and you will see many files d3dx9.
  Monopoly$ oft seems to think it's a good marketing advertising just the DX10-11 concept with
  Vista and Win7. A confusing marketing concept.

  With that cleared up - tell us exactly what is or is not happening.
  EG - accidents to black screen when? When you load or playing?
  It is the only game of the problems?
  You always use the same settings when you played the game under XP or have you tried
  using the highest setting?
  -You have all Windows Updates "Important." There are several
  Games related updates in addition to sp1 which is a must have.
  -Do you have installed recent graphics and audio drivers?

  Tweak guides may be useful for fine tuning Games - TweakGuides.com

• Creating cloud has a black screen

  Updated Creative cloud today and came back to a black screen with no possibility of dialogue, photo is below.  I tried to delete the OODB or folder in the user/local folder and started in safe mode to connect, but when I came back to the normal environment, this problem is still there.  Of course the customer contact center cat care had me waiting more than two hours.  Any thoughts?

  

  So it's a combination of things.  First I had to completely uninstall all Adobe (which is unfortunate) products, and then run the cleaner, reboot.  Install CC, reboot.  Then configure compatibility 256 TIMES color put on switching to energy saving chart, then the update.  It finally worked.  But thanks for your help, it was a great help to get through all this!