My phone has stopped ringing, but it will vibrate and display on call incoming screen then what direction should I have it on ring outloud.  I don't remember changing anything?

Similar Questions

• My iPhone 5 has stopped ringing

  MY I have 5s Pone has stopped ringing. It vibrates again to warn calls incoming, texts, etc. but not sound.

  Sample ringtones led can still be heard in circles - sounds. Can anyone help.

  Is there a moon at the top right of the home screen?  If so - do not disturb is on.

  Visit this link: Re: my Iphone does not ring or done just vibrates all sound

• Need help, get message display driver has stopped working, but has recovered

  Had no problems until recently, my freezer of mouse and screen, then get message display driver has stopped working, but recovered it gets really bad, please help

  Hello

  1. what operating system do you use?
  2. What is the brand and model of your system?
  3. Once you get this error message?
  4. you did it before the issue of any material changes or software?

  Try the steps outlined in the methods mentioned below and let us know if it helps.
  Note: The following Microsoft Articles are applicable for Windows 7 and Vista.

  Method 1: Boot your system in clean boot mode and temporarily disable your antivirus software. Check if get the same error message or not.

  Step 1: Try now to the KB article to perform the clean boot:
  How to troubleshoot a problem by performing a clean boot in Windows Vista and Windows 7:
  http://support.Microsoft.com/kb/929135
  Important: After you used the clean boot in order to solve your problem follow step 7 to reset the computer to start as usual.

  Clean boot in XP:

  Try now to the KB article to perform the clean boot:
  http://support.Microsoft.com/kb/310353
  Important: After you use the clean boot in order to solve your problem follow the steps in the "steps to configure Windows to use a Normal startup state" section to start your system in normal mode.

  Step 2: Turn off the antivirus software:
  http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software
  Important: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks

  Method 3: update the driver for
  

  Updated a hardware driver that is not working properly:
  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  Method 4: Please visit the manufacturer's website and download the latest driver for your graphics card.

  Method 5: Windows 7 power save settings reduces the voltage to the video card too well when it is inactive for some video cards.

  To resolve this problem, disable the display (Plugged In) turn it off and turn off the display (on battery) power settings by using one of the following methods:

  Use the Group Policy settings:
  To resolve this issue by using Group Policy settings, follow these steps:

  (a) click Start, type gpedit.msc in the search box and press ENTER.

  (b) in the local Group Policy Editor, expand models of administration under Computer Configuration, expand System, expand power management, and then click display and video settings.

  (c) in the dialog box that opens, double click on turn off the display (Plugged In), click active, type 0 in the box to turn the display Off (seconds), and then click OK.

  (d) in the dialog box that opens, double click on turn off the display (on drums), click active, type 0 in the box to turn the display Off (seconds), and then click OK.

  Use the powercfg command:
  To resolve this issue by using the powercfg command, follow these steps:

  (a) click Start, type command prompt in the search box, and then click command prompt in the list of results.

  (b) at the command prompt, type the following commands:
  powercfg - X-monitor-timeout-ac 0
  powercfg - X-monitor-timeout-dc 0

  Get back to us if the problem persists.

• I use Windows XP, when I try to install 2 network connection on a PC, AAQMS has stopped working, but if I disable the secand connection quite well.

  original title: connection to a network PC 2

  I use Windows XP, when I try to install 2 network connection on a PC, AAQMS has stopped working, but if I disable the secand connection quite well.

  1 connected directly to the AAQMS system for the Air monitoring

  2. connect directly to the LAN of the company

  There is a solution that I can't connect two without any AAQMS system shutdown.

  Hello

  Your Windows XP question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the TechNet Windows XP Networking forum.

  http://social.technet.Microsoft.com/forums/en/category/windowsxpitpro

• Display driver igfx has stopped responding, but has recovered, blue screen with a Bcc Code of 117.

  Original title: igfx display driver

  I keep getting a message "the igfx display driver has stopped responding but has recovered.  A few times, it goes to a blue screen.  I'm not playing games when that happens.  My history of problem says it is a LiveKernelEvent with a Bcc Code of 117.  It began in May 2010 and continues.  I checked my driver and it is updated, or so it is said.  There must be some type of conflict.  All solutions?

  This might work, keep in mind this is a templete response

  Problem: something which called TDR auditor monitors for computer hardware, particularly the GPU, is tell the GPU constantly meet with computer for 2 seconds checker TDR restarts the driver. The TDR auditor has been good on paper but does not work in the real world. as a gpu may stop responding when he works hard.

  Issue since the time of vista, this is why this problem virually never happened on XP

  Here is the solution
  Exit all Windows-based programs.
  Click Start, type regedit in the search box, and then double-click regedit.exe from the above results. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
  Locate and then click the following registry subkey:
  HKEY_LOCAL_MACHINE\SYSTEM\ControlSet002 (sometimes called ControlSet001) \Control\GraphicsDrivers

  On the Edit menu, click New, and then select the following registry value in the menu drop-down specific to your version of Windows (32-bit or 64-bit):

  For 32-bit Windows
  Select DWORD (32-bit) value.
  Type TdrDelay as the name, and then press ENTER.
  Double-click on TdrDelay and add 8 to the value data and click OK.

  For 64-bit Windows

  Select QWORD (64-bit) value.
  Type TdrDelay as the name, and then press ENTER.
  Double-click on TdrDelay and add 8 to the value data and click OK.

  Close the registry editor, and then restart your computer for the changes to take effect.

  This puts a delay on the auditor of tdr of 8 seconds, so the gpu may stop responding for 10 seconds, this usually fixes the problem, if you are still suffering from this problem (after a reinstall of the drivers or updates, you know this annoying driver stuff)
  To do this, do the same thing but instead of the 'TdrDelay' 'TdrLevel' type, enter the value data as 0 (it is on natively, but check) and then delete the TdrDelay.

  Restart

  Which turns off completely Tdr checker, so windows now 7/vista/8 now works more like windows XP

  Share the info XD

• Windows Media Player 11 has STOPPED WORKING... XP AND Vista problems

  I have a home network with computers XP and Vista.   Computer XP is Dell Dimension 4600.  Vista computer is HP Pavilion Slimline.

  On or about 6/10, WMP 11 on the Vista computer has stopped working properly.  Video will not play digital video (mpeg format), previously working but playing the audio from the file and the timer updates the video plays.

  Attempt to update the codecs (K-Lite).  Didn't help... now, the native multimedia player K-Lite is the same way.

  Deleting updates 6/10 and later versions.  No change.

  System restore of flowing it at 6/9, 6/5, 6/4.  Restoration is back with "unexpected error".  The logs show a NTFS corrupted and suggested chkdsk run.  Filled with chkdsk c: /R with NO ERRORS.

  Ran SFC/scannow on Vista machine.  He said "no violation of integrity.

  Today (6/14), WMP 11 on XP machine has stopped working.  Videos will be running, but are extremely hectic, like something, it's stealing time CPU; However, the system idle process is higher than 90%.

  What the hell is happening?

  EDIT TO add: I want to stress something else... Movie Maker on both machines still work.  Videos can be imported into and read correctly.

  I had things market... Finally.

  I have none of the above.  I do not have the installation diskettes (OEM on a computer HP... no disks provided with the machine, have only the recovery disks that I made when I configured the system).

  So until I went looking for a set of discs that I use, I did the following... and I * think * I know I could fix it, but I do not know...

  I have re installed the K-Lite codec pack... only of video codecs.  I essentially took the video installation by default EXCEPT... I turned off video acceleration.  Intel Express Chipset not allow me to disable hardware acceleration by using its own GUI and Windows Vista would not touch parameters of acceleration as Intel ordered to them.  Well, I suppose that K-Lite has been able to do what could not do Windows and Intel wouldn't let me do.

  Don't know if that was the fix or not, but everything works now.

• My computer will display the BIOS boot screen then do nothing yet, I insert the Windows installation disc. What should I do with it?

  My computer will display the BIOS boot screen then do nothing yet, I insert the Windows installation disc and I press F11, 12 > no response, F10 > BIOS Setup. What should I do with it?

  Brand: HP
  Type: laptop
  Model No.: Pavilion zt3000
  512 MB DDR1 RAM
  Thank you very much!

  Hi Dominic,

  Are you able to get into BIOS to make changes?

  If so, you can try to reset the default settings of the BIOS and check.

  NOTE: Change (CMOS) BIOS/complementary metal oxide semiconductor settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  You can also try to remove all external usb devices that can be connected to the system and start-up and see if the system boots.

• My monitor has shadows after every letter I type and my icons of the screen.

  My monitor has shadows after every letter I type and my icons of the screen - how can I make them disappear?

  Hello

  1. All changes made to the computer before the show?
  2. What brand / model of the computer?
  Method 1:
  This problem may occur the display drivers have not been updated. Check out the link and follow the steps to update the drivers.
  Updated a hardware driver that is not working properly
  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly
  You can also visit the link and follow the steps.
  Update drivers: recommended links
  http://Windows.Microsoft.com/en-us/Windows7/update-drivers-recommended-links
   
  Method 2:
  Check out the link and follow the steps to check if a non-Microsoft service is causing a conflict for the problem to occur.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: once the diagnosis is made, follow step 7 of section to configure the computer to start the Normal start.

• I downloaded the trial of the creative cloud vision. But why does the application display a completely black screen?

  I downloaded the trial of the creative cloud vision. But why does the application display a completely black screen?

  I can open the CC but I don't see anything in it.

  I downloaded and months before photoshop. I still see something at the window right there.

  But now, I see the dark window. So I couldn't download the Adobe Illustrator.

  Please help.

  Hello

  Please see the thread below where this issue was discussed:

  Re: screen creative black cloud

  Kind regards

  Sheena

• HP Pavilion DV6: at startup BIOS showing CPU fan has stopped working, but I checked the fan is in good condition

  Hello

  I bought my HP Pavilion dv6 laptop 2011 as it starts a is overheating, freezing windows with noisy fan sound etc... but now, on information in BIOS boot indicating that the CPU fan has stopped working so immediately, I checked that I couldn't hear any noise from fan and no symptoms as fan works so I disassembled my laptop and removed CPU cooler fan only. Simply with the help of the battery, I checked the CPU fan it is running perfectly alone. but it does not work with the laptop.

  Please help me and guide what is the cause of this problem and how to solve this problem.

  Gassab

  HI @Kartic

  Welcome to the HP Forums!

  This is a fantastic place to find answers and suggestions!
  You have the best experience in the HP forum, I would like to draw your attention to the Guide of the HP Forums Learn how Post and more

  How can I find my model number or product number?

  I understand that since you had the laptop he had an overheating problem with a loud fan noise that causes freeze it.

  Recently, you have received the message that the CPU fan has stopped working and you couldn't hear the rotation of the fan to the top.

  You have removed the fan and checked, but the fan works.  It is possible that the connection was not safe in Notepad.

  Here is a link to an overheating and Auto Shutdown problem troubleshooting.

  Have you checked for an update of the bios of your laptop. You have provided the series of laptop you have, but not the exact model, so I'm not able to check it for you.

  You can run the Wizard to help HPin order to facilitate this process.

  Like a bios update has the potential to cause damage, you can contact HP technical support using this procedure.

  Please contact our technical support at 800-474-6836. If you do not live in the United States / Canada region, please click on the link below to get a number of assistance for your region.

  World wide phone holder

  Here is a link to the guide to maintenance and Service Guide HP Pavilion dv6000 Notebook PC for your laptop.

  You can replace the thermal paste on the processor. Here is a link to a YouTube video on this process.

  How to apply thermal paste

  Good luck!

• PC-Doctor module has stopped working, but do not know if I have it on my computer...

  In the last 3-4 days I get a window intermitant arise seems them to be a "Microsoft Windows" its origin in the upper left corner of the window saying: "PC-DOCTOR MODULE has stopped working. A prolem caused the program to stop working correctly.  Windows will close the program and notify or if a solution is available. "Then a box of"close the program ".  I find 'FIND' to search for a program of the PC-DOCTOR MODULE and can not find one on my system. and "googled" it and came up with some info, but I'm not sure if it's a real source of assistance of a scam 'spyware '!   What I treat, something real, or something trying to eat me alive somehow?

  In the last 3-4 days I get a window intermitant arise seems them to be a "Microsoft Windows" its origin in the upper left corner of the window saying: "PC-DOCTOR MODULE has stopped working. A prolem caused the program to stop working correctly.  Windows will close the program and notify or if a solution is available. "Then a box of"close the program ".  I find 'FIND' to search for a program of the PC-DOCTOR MODULE and can not find one on my system. and "googled" it and came up with some info, but I'm not sure if it's a real source of assistance of a scam 'spyware '!   What I treat, something real, or something trying to eat me alive somehow?

  Hey Toccet

  to be on the good side for malware scan

  Download update and scan with the free version of malwarebytes anti-malware

  http://www.Malwarebytes.org/MBAM.php

  You can also download and run rkill to stop the process of problem if it is malware before you download and scan with malwarebytes

  http://www.bleepingcomputer.com/download/anti-virus/rkill

  If this does not work in normal mode only the above work in SafeMode with networking

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode with networking with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  Walter, the time zone traveller

• Qosmio X 70 - graphics driver has stopped working, but has recovered

  IM using a laptop Qosmio X 70 but when im using Photoshop to edit photos, I get a window telling me that the "graphics card stopped working but recovered", but the one to get Photoshop working again is closing in the Device Manager, then everything that I have worked on pop up is lost ,

  How can I fix it if it does not happen?

  What graphics card driver do you mean exactly?

  The fact is that Qosmio X 70 - a models were equipped with an external graphics (nVidia) and the Intel CPU provides additional internal Intel HD graphics (according to the CPU)

  Since the application Photoshop needs a lot of graphics performance (RAM), it would be desirable to use the NVidia GPU for execution using the Photoshop software.

  I recommend you to change the settings for nVidia and assign the photoshop to nVidia GPU.
  The setting can be changed in the nVidia control panel

  There, you must choose the "manage 3D settings" (can be found on the left in the nVidia control panel)
  Now in the main window, you will find two tabs "Global settings" and "program parameters".
  In the 'Program settings' tab select the application (Photoshop) that should use the nVIdia GPU

  If it is not listed, click the Add button
  Then choose the graphic processor preferred for this program (generally must be nVidia processor high performance)

  In "specific settings for this program", you can assign additional features to improve performance.

• "Windows Explorer has stopped working,... will collect information '..." and taskbar Windows in the background keep trying restarts again & again

  Yesterday I moved a movie file video of my D: drive on drive C: (the two C & D are my partitioned hard drive), but shortly after I moved, my laptop becomes unresponsive, then, a pop-up window will appear and say: 'Windows Explorer does not work, the window now collects data & will take a few moments "...
   
  The real problem is... continuous refreshing office it self as it seems an attempt to Windows restarts auto, it's unrespondesive to the greater part of the order, even if I can finally to click on Control Panel / my computer, it took me 15 minutes,...
   
  Here's what I myself had tried but still could have solved the DIF:
  1. launch McAfee analysis, took the hour and a half,... no virus is detected.
   
  2. unplug the computer and turn it back... re-started in normal mode and safe mode, after reboot, problem still there...
   
  3. re-started in normal mode, perform a restore of the system to a previous date... tried 2 times, but still problem after restore.
   
  4. tried to restore the system to safe mode, but find out they do not have restore option in SafeMode... don't understand why.
   
  Here is some info from my laptop:
  Sony AR - 770 Vista Ultimate
  4 GB RAM SDRAM
  400 GB 5400 RPM HARD drive
  Intel T9500 2.6 GHz

  Thank you... I thought that no one answer,... so I went to come and do a clean install of Windows from the recovery discs... but after I finished the installation, one intel consul appears & saying my RAID 1 volume & 2 are failed and cannot read or write and suggest me to back up immediately,... so I had to call sony again once , they said to my HDD / really messed material,... .do to buy a new hard drive,... What has...

  but thanks again...

• error message this device driver has stopped responding, but recovered. What can I do to fix this?

  HP G72-b60US notebook

  Windows 7 Edition 64-bit family

  Intel graphics card

  I play a game and it's going very well for 10 minutes, then screen wil go black and trying to "fight" to override the game to bring up the office. then an error message is displayed to tell the device driver is not responding but recovered. I'm trying to get back into the game, but it doesn't allow me not-screen remains black when I try to turn on or off. so I have to ctrl-alt-del to bring up the Task Manager to stop the game. Then, the computer and the graphics card works fine. I tried to see if the driver for the graphics card needs update but the CV Wizard and windows update tells me that everything is fine. Help?

  Thank you.

  Angie

  Hello

  A.

  Check that your laptop is overheating or not.

  To do this use HWMonitor (free and recommended).

  If it detects overheating, consult this guide.

  B.

  Update the Bios.

  The update of the Bios?

  
  

  Download the last update of the Bios here.

  Connect the power adapter to the netbook.

  Disconnect from the Internet. Close all running programs. Disable anti-virus and firewall.

  Double-click the Bios update exe file. It may take some time, so it is important to remain patient, not to interrupt the process. Allow the laptop to restart after applying the BIOS update.

  Although this update is running are not:

  • Turn off your laptop,
  • Disconnect the power adapter,
  • try to run any software or do anything thereon.

  Note:

  The Bios update process is always risky. You do this at your own risk.

  C.

  Update the graphics driver.

  Uninstall the Intel graphics driver.

  Resources:
  Uninstall software in Windows 7

  Uninstall or change a program in Windows 7

  Download and install the latest driver from here.

• My j3680 solution Center has stopped working. I can print and fax manually. I downloaded the full

  My j3680 solution Center has stopped working. I am able to print and fax manually but can't scan. My system is windows 7.

  The 3680 is an officejet all-in-one.

  Hi mahroch,

  The first thing to do to solve this problem would be to run printing HP and doctor Scan. It is a quick and simple tool that diagnoses and solves many problems of printing, scanning and connectivity. See the following link for more information on downloading, installing and running this tool:

  http://goo.GL/SGZxs

  Let me know if this solves the problem, and if not, what the tool provides.