My router ip local chnaged to 10.144.108.141 by default 192.168.1.1

Similar Questions

• under vista and it cannot open the Web 192.168.1.1 for linksys router

  I have a Linksys wrt54gl router wireless and I hard wire plugged into my computer so I connected to the internet broadband router. Connections to work because the flashing lights on the front of the router blink correctly.  So I open internet explore and type 192.168.1.1 in the hope that I get the page for the router setting, but instead, I get a message that explore cannot detect the Web site. Wrong address. I get a similar error with Firefox.  The computer was working fine connected directly to the internet bandwidth so sure the internet works. The IP address is set to automatic detection. Someone at - it ideas?

  Hello

  Make sure that the software firewall on each computer allows free local traffic. If you use 3rd party Firewall on, Vista/XP Firewall Native should be disabled, and the active firewall has adjusted to your network numbers IP on what is sometimes called the Zone of confidence (see part 3 firewall instructions

  General example, http://www.ezlan.net/faq#trusted
  Please note that some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible, configure the firewall correctly or completely uninstall to allow a clean flow of local network traffic. If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Why won't my router save the changes to 192.168.0.1 DNS settings? (DGN2200v4)

  I just bought a DGN2200v4 and successfully connected to the internet. However, it took me ages to figure out how to save the changes made to DNS settings. (I wanted to use "OpenDNS" on 208.67.222.222)

  It turns out that if I connect to the router through 192.168.0.1, I can not change the DNS settings. When I click "Apply" after entering the new numbering, it takes 30 seconds or more for the progress bar for complete, but no change is made. i.e. it does not save the changes I made.

  If instead I connect to the router via www.routerlogin.net, changes are correctly saved after clicking 'Apply', with the progress bar by taking 30 seconds or more.

  I tried several times with consistent results. Why 192.168.0.1 not working then as www.routerlogin.net don't? I thought they were equivalent - the webpage 'Netgear genius' is identical on both...

  JC

  JCA says:

  
  

  Also, do you recommend make a factory hard reset after the firmware update, or there at - there no need?

  Sorry for the late reply.

  Personally, I tend to reset factory and re - enter the settings manually, unless I've saved a backup of this same version of the firmware. However, I use Netgear as Access Points routers and so I have little data to re-enter. To some people will say that a factory reset is useless and very often they would be correct, but the effects of factory reset no when it may be necessary are often difficult to predict. I was moderator on these forums for a dozen years, and have seen hundreds of threads where the solution to the problems after an update of the firmware has been at the factory to reset the router.

• I have reset my etec router and now I can not past the prompt 192.168.1.1. My pc is 8 years old and very, very slow

  I tried for two days now to restore my internet connection.

  I tried for two days now to restore my internet connection.

  192.168.1.1 is probably access your router's IP address and it could be a Linksys.

  If you reset your router, we help can'r you. You will need to access the router and configuring PPPoE username and password.

  Call your service provider.

  Why in the world would you reset your router if you didn't know how to put in place a new or know what to do then? It's like taking something apart and not knowing how to wind again.

• Cannot Router Log-Out definition 192.168.1.1

  I have a router E4200 v.01 and when I upgraded to the latest firmware (due to the exploitation of security) it seems that every time the configuration of the router (192.168.1.1) acess it ask me not or at the entrance of the admin and the password, use the wifi or wired... I want the usual process, whenever I go to 192.168.1.1 it will ask me to enter my admin and the password to change the settings for my router... no matter what help will do... Thank you...

  Found the Solution... Just uninstall the installation of cisco software and the automatic connection will be gone... hope that cisco will fix software traore, like the old software... When you open the program you see a list of device connected to your router and can challenge and see the connection that has an error or what...

• E8350 in Bridge mode allow me access to the router with 192.168.1.1

  I have a small home network with the E8350 (AC2400) and a PK5001A of Qwest ActionTec modem.  I needed to put the router in Bridge mode to enable NAT in the modem works properly.  By simply disabling the NAT in the E8350 network broe. Once I placed the E8350 in bridge mode, I lost connectivity via 192.168.1.1.  The network seems to work correctly, I can't access the router remotely.  Is this normal or is it a different setting I'm missing?

  When you have done this, you probably have a new ip address of the primary router. See what she is looking at the main router connections or by manually adjusting it 192.168.1.2 or some other ip that is in your network. If the primary router uses a different subnet as 192.168.0.x, then you must use an IP also in this same range.

• I can't access my linksys router using 192,168.1.1 or ping the router or research on the ipconfig command.

  Access router

  I can't access my linksys router using 192,168.1.1 or ping the router or research on the ipconfig command. 192.168.1.1 is the URL and only worked twice in the multiple attempts

  Are you absolutely sure this is the IP address of the gateway?

  Open a command prompt and type "ipconfig/all" (without the quotes, noting the space between ipconfig and / all) and see what it teaches you about the IP Address of the default gateway.

• Why the WAN ip displayed on my local server like the 192.168.1.1?

  I got Minecraft Server on my PC

  I have RV180W
  Minecraft server using port 25565 to connect players.
  I transferred the port 25565 my public Static WAN IP to 192.168.1.100
  When the connected Playes - server say is me. as any player to internet connected to my router (192.168.1.1)
  I can not ban players to their intellectual property. I can not set up only 1 entry of 1 IP

  The old Chinese TP-Link I don't have this problem, but tp-link is lagging players and disconecting. Now I want to find a way to repair, or sell my RV180W and but NORMAL router.
  Please, help me wth it. Dark days comes to my wonderfull Minecaft server.

  Hello Bogdan,

  I think you are describing the same question in this post: https://supportforums.cisco.com/message/3884520#3884520

  As you can see the end of discussion, we still do not have an official communiqué, which solve this problem. You can call the Cisco SB helpdesk and open a Service request. I can't confirm if there is already a beta version which fix, but at least you will be informed when it's done.

• Why can't I access the modem 192.168.1.1 when connected to the wireless router?

  I'm unable to access my DSL Modem 6100 Westell using 192.168.1.1 when connected to the Netgear WNDR3400 wireless router. I can access it, however, when I connect directly to the ethernet port on the computer without going through the router. I've set up according to the instructions. Is it possible to correct the problem?

  This isn't a problem.  This is the standard behavior.  You are connected to the side LAN of the router that is isolated from the side WAN (uplink).  This is the mode of operation of routers.

• can not access the router (192.168.1.1) of the browser firefox web

  When I try to access my RV042G Gigabit Dual WAN VPN router from firefox or chrome I get an error message

  > An error occurred during a connection to 192.168.1.1. SSL has received a low ephemeral Diffie-Hellman key in the handshake message exchange the server key. (Error code: ssl_error_weak_server_ephemeral_dh_key)

  I had a similar problem with the storage attached network (Synology Diskstation) unit but I was able to create a certificate that meets the "modern standards" and the problem was solved.

  I need to create a new certificate for the web server on the router RV042G?  How?

  FYI - running firmware 4.2.3.06

  Thank you

  Lee

  Hello Lawrence,.

  Thank you for using the small community of Support Business!

  It is a known problem that affects a number of products for small business. There is another post which lies here who has some solutions you can try.

  If you have any other questions, please post them here and I'll do my best to help you!

  Best,

  Taylor

• New att/motorola modem with linksys wireless router connects local only!

  Trying to set up my linksys wireless router to connect to the internet. I get local only access. Just got the new modem and was able to connect to the internet with a wired connection. I had no problem with my router and adapter wireless during the last 3 years. They had to create a new connection broadband with the modem to local and internet access. My Wi - Fi is a new connection, local only. Any help would be appreciated so to get my connection wireless internet.

  Hello

  Let us work together to solve this problem.

  I ask you to follow these links and check if the problem is resolved:

  Set up a wireless router
  http://Windows.Microsoft.com/en-in/Windows-Vista/set-up-a-wireless-router

  Setting up a wireless network
  http://Windows.Microsoft.com/en-in/Windows-Vista/setting-up-a-wireless-network

  Wireless network card: frequently asked questions
  http://Windows.Microsoft.com/en-in/Windows-Vista/wireless-networking-frequently-asked-questions

  For more information:

  http://social.technet.Microsoft.com/forums/en-us/itprovistanetworking/thread/4215a10d-08DD-404A-a43a-635a2f141f0d

  Warning: using third-party software, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third-party software can be solved. Software using third party is at your own risk.

  Please let us know the status of the issue.

• Set the locale to English instead of the browser by default

  I noticed that when I open an ADF application in my browser than the locale by default in my browser.
  How can I let the application know that there no need to take the regional settings of his browser user, but still use English?

  You can decide not to support the other language by setting only the local by default in faces.config.xml.

  Kind regards

  ~ Simon

• ASA "route inside 0 0 192.168.1.1 by tunnel" interface ACL question

  Hello

  Small question around the road inside 0.0.0.0 0.0.0.0 192.168.1.2 in tunnel command.

  Do you need to add a u-turn traffic within the ACL interfaces (for example internet related http traffic) or 'same-security-traffic permit intra-interface' negates the need of this?

  So if my site remote vpn outside is 10.1.1.0/24 should I add entering permitted statements for the 10.1.1.0/24 inside my interface.

  Thank you

  same-security-traffic permit intra-interface allows then-input-output traffic on a single interface

  allowed incoming 10.1.1.0/24 statement in the list ACL allows traffic (output - then-) penetration on a single interface, but you must disable the RPF check

• Daisy chaining with other routers and the common IP range EA6500 V2

  I have a local network of...

  • a modem
  • a gateway connected to the modem computer/server
  • has a modem-router connected to the gateway/server via the port of the gateway/internet
    (gateway/a two server NETWORK interface card)
  • a and B modem router wireless connected to the router via the gateway/router internet port B
  • both A and B using the same set of IP addresses, 192.168.0.XXX

  Now I want to do the same thing with my Linksys EA6500 V2 I did with router B, I want to connect the Linksys router has via gateway/internet port on Linksys.  In addition, I want the Linksys router to use the DHCP server on the gateway server / as everyone is on the local network and, of course, I want to use the series of IP addresses, 192.168.0.XXX.

  What I tried to do is to disable DHCP on the Linksys service, but nothing seems to change once the changes are activated.  I look in the Local network settings and see all the old default 192.168.1.1 for the router address and so on.  I also tried to change the address of the router manually an address of 192.168.0.x and was immediately cut off this subnet.  I tried the renewal of my Windows client computer and couldn't do that either.  And as my client could not change its own address 192.168.1.X, I couldn't reach the router to the address that I gave him.

  How can I set up this router so that it uses the DHCP server on the gateway/server computer, including acquiring its own address in the same series.  Or at least set up so that it uses the same series of address than the rest of the LAN and no longer functions as a separate subnet?

  It seemed that all I had to do to set up router B to connect this way was to disable the DHCP server and everything fell into place, no problem.  Is this all I need to do here?  Am I supposed to restart or something?  I'm tired of guessing and trial and error.

  All tips or hints would be appreciated.

  You have to give the EA6500 a router static IP address in the same subnet as your network, but not in the DHCP range.

  Follow the instructions for 'LAN to LAN' Cascading in the link below:

  In waterfall or connect a Linksys router to another router

  Thing to keep in mind when cascading a router:

  1. Change the IP address of the secondary router to something like 192.168.1.254 so its on the same network, but is not in conflict with the main router
  2. Make sure that the DHCP service is disabled on the secondary router
  3. Make sure that nothing is ever connected to the internet port of the secondary router
  4. Differentiate the wireless SSID by location (Ex: downstairs) and the channel

• Cisco router access outside the local network interface

  Hi all!

  I have Cisco router 892 (c890-universalk9 - mz.154 - 3.M4.bin) with firewall area and based on routing strategies.

  Everything works fine, but now I need to have the ability to access external router interface IP LAN addresses.

  For example, I PAT 192.168.4.1 port 8443 to the outside interface IP (93.93.93.2 for example) and I need to check LAN 93.93.93.2:8443.

  ! PAT:

  IP nat inside source static tcp 192.168.4.1 8443 93.93.93.1 - extensible 8443 SDM_RMAP_1 road map

  ! DynNat to the internet:

  IP nat inside source overload map route SDM_RMAP_1 interface GigabitEthernet0

  ! Routing policy

  SDM_RMAP_1 allowed 10 route map
  corresponds to the IP 101
  match interface GigabitEthernet0

  ! ACL 101 for routing policy

  access-list 101 deny ip 192.168.3.0 0.0.0.255 192.168.111.0 0.0.0.255
  access-list 101 deny ip 192.168.3.0 0.0.0.255 172.16.192.0 0.0.0.255
  access-list 101 deny ip 192.168.3.0 0.0.0.255 172.16.177.0 0.0.0.255
  access-list 101 deny ip 192.168.3.0 0.0.0.255 172.16.61.0 0.0.0.255
  access-list 101 deny ip 192.168.3.0 0.0.0.255 172.17.19.0 0.0.0.255
  access-list 101 deny ip 192.168.4.0 0.0.0.255 192.168.111.0 0.0.0.255
  access-list 101 deny ip 192.168.3.0 0.0.0.255 host 172.16.194.100
  access-list 101 deny ip 192.168.3.0 0.0.0.255 10.0.0.0 0.255.255.255
  access-list 101 deny ip 192.168.4.0 0.0.0.255 10.0.0.0 0.255.255.255
  access-list 101 deny ip 192.168.4.0 0.0.0.255 host 172.31.255.1
  access-list 101 deny ip 192.168.4.0 0.0.0.255 host 172.16.194.100
  access-list 101 permit ip 192.168.3.0 0.0.0.255 any
  access-list 101 permit ip 192.168.4.0 0.0.0.255 any

  ! ACL on the external interface:

  plug-in software component gi0 extended IP access list
  allow an ip
  allow icmp a whole

  ! External interface

  interface GigabitEthernet0
  Description $ETH - WAN$
  IP 93.93.93.1 255.255.255.240
  IP access-group gi0-in in
  NAT outside IP
  IP virtual-reassembly in
  EXTENT of the Member's area network security
  IP tcp adjust-mss 1452
  automatic duplex
  automatic speed
  card crypto SDM_CMAP_2

  ! Inside DMZ interface vlan:

  interface Vlan4
  IP 192.168.4.254 255.255.255.0
  IP nat inside
  IP virtual-reassembly in
  security of the members of the DMZ
  IP tcp adjust-mss 1452

  ! Allow outbound traffic to DMZ to Internet:

  Allow_All_ACL-DMZ extended IP access list
  allow an esp
  permit tcp host 192.168.4.1 host 192.168.111.2 eq 1521
  refuse the 192.168.4.0 ip 0.0.0.255 192.168.111.0 0.0.0.255
  refuse the 192.168.4.0 ip 0.0.0.255 172.17.19.0 0.0.0.255
  allow icmp 192.168.4.0 0.0.0.255 any
  ip licensing 192.168.4.0 0.0.0.255 any

  ! Allow incoming traffic from the Internet to DMZ:

  WAN_DMZ_ACL extended IP access list
  allow tcp any a Workbench
  permit tcp any any eq ftp
  permit tcp any any eq 990
  permit tcp everything any 51000 53000 Beach
  permit tcp any any eq 995
  permit tcp any any eq 465
  permit tcp any any eq www
  permit any any eq 443 tcp
  allow icmp a whole
  allow an esp
  permit any any eq non500-isakmp udp
  host ip 212.98.162.139 permit 192.168.4.0 0.0.0.255
  IP 81.30.80.0 allow 0.0.0.255 any
  IP 192.168.111.0 allow 0.0.0.255 192.168.4.0 0.0.0.255
  IP 172.17.19.0 allow 0.0.0.255 192.168.4.0 0.0.0.255
  host ip 172.16.194.100 permit 192.168.4.0 0.0.0.255
  host ip 172.31.255.1 permit 192.168.4.0 0.0.0.255
  permit ip host 172.31.255.1 172.17.193.100
  refuse an entire ip

  ! Focus on the area of firewall:

  type of class-card inspect entire game DMZ_WAN_CLASS
  match the group-access name DMZ Allow_All_ACL

  type of class-card inspect entire game WAN_DMZ_CLASS
  match the name of group-access WAN_DMZ_ACL

  type of policy-card inspect DMZ_WAN_POLICY
  class type inspect DMZ_WAN_CLASS
  inspect
  class class by default
  drop

  type of policy-card inspect WAN_DMZ_POLICY
  class type inspect WAN_DMZ_CLASS
  inspect
  class class by default
  drop

  the DMZ security

  
  area WAN security

  Security WAN_DMZ of the pair area source destination WAN DMZ
  type of service-strategy inspect WAN_DMZ_POLICY
  destination of DMZ_WAN source DMZ area pair WAN security
  type of service-strategy inspect DMZ_WAN_POLICY

  Maybe someone can help me to make Cisco to allow ports outside LAN using a NAT?

  I did this on Mikrotik easily = |

  It is due to the fact that they do not allow "hair pinning" by default, once this is configured, it will work.

  Martin