Cannot Router Log-Out definition 192.168.1.1

Similar Questions

• Need help logging on to 192.168.1.1

  Hello
  you try to reset my password for security - and the same problem as listed - tried using admin admin and password password to [url =http://www.192168-11.pw] http://192.168.1.1 [/ url], but seem to have myself locked out.
  What should I do to unlock it?

  webdangol223

  This IP address is one of the two IP addresses as router manufacturers assign systematically to their equipment.  This IP address indicates that the router is running on the 192.168.1 subnet and is the first device on that subnet.

  To speak with this router properly, you must have your PC value to assign IP addresses automatically - through the DHCP settings on the router or assigned manually your PC to 192.168.1.2.

  When you connect to a router, especially newer ones, it will ask you a login and a password.

  We are NOT able to provide to those who, as they are assigned by the manufacturer.  In some cases, this information is included in a booklet that came with the router.  In other cases, it is the printer on a sticker located on the router.

• ASA "route inside 0 0 192.168.1.1 by tunnel" interface ACL question

  Hello

  Small question around the road inside 0.0.0.0 0.0.0.0 192.168.1.2 in tunnel command.

  Do you need to add a u-turn traffic within the ACL interfaces (for example internet related http traffic) or 'same-security-traffic permit intra-interface' negates the need of this?

  So if my site remote vpn outside is 10.1.1.0/24 should I add entering permitted statements for the 10.1.1.0/24 inside my interface.

  Thank you

  same-security-traffic permit intra-interface allows then-input-output traffic on a single interface

  allowed incoming 10.1.1.0/24 statement in the list ACL allows traffic (output - then-) penetration on a single interface, but you must disable the RPF check

• Can't connect to 192.168.1.1 for the reset

  I have reset my box (WRT310N) given that I remember most when I wrote my password. When I went to 192.168.1.1 it wouldn't let me log in with admin and no password. now I have wiped out the box and can't reset it or find the paperwork so I can connect on the new Wii.

  Try again, hold the button of reset for 30 seconds, release.  Wait 30 seconds and cycle power to the router.  Go to 192.168.1.1 with admin username blank password and reconfigure.

• Extremely slow WRT54G navigation pages @ 192.168.1.1 - this could be a problem with network card?

  Friend of mine is having the problems of Internet connection on his main PC which is hard wired to the router, it is using Comcast cable (18Mbit) and all of a sudden today the speed fell to dialup speeds, literally, however its ONLY this main with the issue of speed pc, there are 2 other computers connected wirelessly to the router, and they run at full speed during the test on speedtest.net

  Solve the problem, I tried bypassing the router and still have the issue of speed, so I can pretty much rule out the router, but as part of my troubleshooting whenever I try to access the router configuration pages via 192.168.1.1 but it is VERY slow to respond.

  For example when hitting enter after typing 192.168.1.1 it takes about 45 seconds to view the router configuration page, and then clicking on any other tabs takes 30-45 seconds longer to respond.

  So my main question with this post, is it possible that its network card went bad? What would cause really slow access to the configuration of the router?

  The PC is under Win 7 Ultimate 32 bit and Ive tried to run the network troubleshooter, uninstalled the network card in Device Manager / reinstalled the drivers but nothing seems to work.

  I also ran Malware Bytes and the analytical results were clean.

  Any ideas appreciated!

  can you 'borrow' a card? This is the only way to be sure, eliminating hours of trial and error procedures. one of the mega electronic stores is a good source, if it solves your problem you keep the card, otherwise there is the option to return

• under vista and it cannot open the Web 192.168.1.1 for linksys router

  I have a Linksys wrt54gl router wireless and I hard wire plugged into my computer so I connected to the internet broadband router. Connections to work because the flashing lights on the front of the router blink correctly.  So I open internet explore and type 192.168.1.1 in the hope that I get the page for the router setting, but instead, I get a message that explore cannot detect the Web site. Wrong address. I get a similar error with Firefox.  The computer was working fine connected directly to the internet bandwidth so sure the internet works. The IP address is set to automatic detection. Someone at - it ideas?

  Hello

  Make sure that the software firewall on each computer allows free local traffic. If you use 3rd party Firewall on, Vista/XP Firewall Native should be disabled, and the active firewall has adjusted to your network numbers IP on what is sometimes called the Zone of confidence (see part 3 firewall instructions

  General example, http://www.ezlan.net/faq#trusted
  Please note that some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible, configure the firewall correctly or completely uninstall to allow a clean flow of local network traffic. If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Why won't my router save the changes to 192.168.0.1 DNS settings? (DGN2200v4)

  I just bought a DGN2200v4 and successfully connected to the internet. However, it took me ages to figure out how to save the changes made to DNS settings. (I wanted to use "OpenDNS" on 208.67.222.222)

  It turns out that if I connect to the router through 192.168.0.1, I can not change the DNS settings. When I click "Apply" after entering the new numbering, it takes 30 seconds or more for the progress bar for complete, but no change is made. i.e. it does not save the changes I made.

  If instead I connect to the router via www.routerlogin.net, changes are correctly saved after clicking 'Apply', with the progress bar by taking 30 seconds or more.

  I tried several times with consistent results. Why 192.168.0.1 not working then as www.routerlogin.net don't? I thought they were equivalent - the webpage 'Netgear genius' is identical on both...

  JC

  JCA says:

  
  

  Also, do you recommend make a factory hard reset after the firmware update, or there at - there no need?

  Sorry for the late reply.

  Personally, I tend to reset factory and re - enter the settings manually, unless I've saved a backup of this same version of the firmware. However, I use Netgear as Access Points routers and so I have little data to re-enter. To some people will say that a factory reset is useless and very often they would be correct, but the effects of factory reset no when it may be necessary are often difficult to predict. I was moderator on these forums for a dozen years, and have seen hundreds of threads where the solution to the problems after an update of the firmware has been at the factory to reset the router.

• Cannot access the WRT320N cascading to the IP 192.168.1.2

  I have two routers WRT320N running.  The first is 192.168.1.1 IP and DHCP turned on and connected to the cable modem.  The second WRT320N is IP 192.168.1.2, disabled DHCP, NAT disabled.  The second router is connected to the first by using one of the ports labeled 1thorugh 4; the WAN port on the second router is not used.  Both routers are configured for wireless with an appropriate warranty, etc.  I put Remore management 'on' and put at the disposal of all property intellectual.  Now, I realize that remote management can be provided for use of the internet (not my intended use) rather than on the same home network.

  Good new first: the works of all things.  Devices wired for both routers have internet access and can 'see' each other for sharing of files, etc.  In addition, devices wireless on both networks seem to work OK, and the first router [192.168.1.1] shows all devices as clients, no matter what router they are physically or wireless connected to.

  Now the bad news: although it has worked reliably for days, I now can't access the second router [192.168.1.2] from anywhere in the network (no matter what router, the computer is connected to).  Work of its customers and you can test it with success of any computer, but when I type http://192.168.1.2 on IE or Firefox from any computer, it times out.  No dialog box asking for the password; not nothing.  All times out.  I tried the cyclical power router, but that has no effect.  Once again, during the first days, it seemed to work.  I could type http://192.168.1.2 of any client in the network and access the Router 2 very well and see its settings, set its SSID, etc etc.  Still, the router seems to work as I would and my network performance is OK, even for clients on the second router wireless, but I can not only access the URL.

  I'm sure I can hit 'reset' and that it will probably heal, but it also means that I have to start from scratch on a long list of the customizations I made to its settings, including. SSID, security, IP address, NAT configuration, etc. etc. (I save a configuration after I put in place.)  Is the only option to reset and then re - load the saved configuration? )

  Any thoughts here?  It is always tempting to blame firmware, especially when it works OK for a while, and then it stopped working.  Of course, I could also do sometihng evil.  Any help appreciated.  Thank you.

  to: Helm

  Thank you very much.

  It turns out that I had to do the factory reset, and then I have download the old config file until I'm your answer

  so far, all is well... the device seems to move traffic as it should, and I can access it again by entering the URL http://192.168.1.2

  I'll see how long the 'fix' hard... I really think they have a bug in the firmware there somewhere

  If she out craps again, I will set up from scratch, as you suggest.

  Thanks a lot for your help

  I think I'm 'good' for now.

• My router ip local chnaged to 10.144.108.141 by default 192.168.1.1

  last night I tried to access my linksys router admin page and was not able to connect then I connect to mysmartwifi login Web page and found out my local router ip settings been changed as mention above about the

  what I did recently I moved my placement of the router and I added extension range netis router WF2411

  I got connected to the modem and to my linksys netis, netis but after that I took it off the coast and the only router that I have now is my linksys

  I changed the parameters of local ip address to 192.168.1.1 but still trying to find out how it happened

  What should I do if it's been hacked

  EA 6400 with Teksavvy Internet Linksys

  No one has changed on you, this is a feature of AutoCorrect in the EA series routers.

  EA6400:

  Connectivity-online-online details router LAN => Edit

• We cannot open Skype. You are already signed in on this computer. Please log out and try again.

  Hello

  Please help me, I uninstall and download the latest version of Skype, but it is not sign in. give below error.

  We cannot open Skype. You are already signed in on this computer. Please log out and try again.

  Please help me solve this problem. I have no account of any loged in on Skype so why this error happens, or even no 8 Skype window does work I have also uninstall Skype window and install Skype Office fresh but error please help me solve. Thanks in advance.

  

  Start your Windows in safe mode and then try to rename the folder % appdata%\Skype.

  http://www.howtogeek.com/107511/

• When I try to connect my computer with XP operating system, I get this error message to: rund1132.exe and cannot log out.

  original title: log question.

  When I try to connect my computer with XP operating system, I get this error message to: rund1132.exe and cannot log out.  How can I fix?

  Hi KERRYYX,

  1. Did you the latest changes on the computer?
  2. When was the last time it was working fine?
  3. You have security software installed on the computer?
  4. What is the full error message that you receive?
  5. Are you able to restart and shut down the computer?

  It is possible that some third-party programs installed on the computer is causing the problem.

  I suggest that you put the computer in a clean boot state and check if it helps.

  To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  See section to learn more about how to clean boot.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  (a) click Start, type msconfig in the search box and press ENTER.

  (b) If you are prompted for an administrator password or for confirmation, type your password or click on continue.

  (c) under the general tab, click the Normal startup option, and then click OK.

  (d) when you are prompted to restart the computer, click on restart.

  You cannot log off, restart or shut down your Windows XP-based computer

  http://support.Microsoft.com/kb/831431

• I have reset my etec router and now I can not past the prompt 192.168.1.1. My pc is 8 years old and very, very slow

  I tried for two days now to restore my internet connection.

  I tried for two days now to restore my internet connection.

  192.168.1.1 is probably access your router's IP address and it could be a Linksys.

  If you reset your router, we help can'r you. You will need to access the router and configuring PPPoE username and password.

  Call your service provider.

  Why in the world would you reset your router if you didn't know how to put in place a new or know what to do then? It's like taking something apart and not knowing how to wind again.

• Cannot communicate with the first DNS Server (192.168.0.1)

  For about a week and a half now my brother could access the internet.  When "analyze us" the network connection, it shows the message above.

  Research for this phrase raise a lot of people with problems with wireless on a laptop, but it is an office with an Ethernet connection, which worked fine for the last 4 years of 100 MB.
  It is running Vista x 64.
  We managed to fix briefly by uninstalling the drivers for the network card and rebooting, but now even that does not work.
  Ipconfig/all shows, there always the same IP address that he always had and the NIC has the same with my fully accessible machine, 192.168.0.1 DNS server address.
  I have also tried the/flushdns / release & renew functions without result.
  I also tried to totally replace the drivers with a new download on Marvell website and still no joy.
  Here's a copy of his ipconfig:
  Windows IP configuration

  Name of the host...: PC-user

  Primary Dns suffix...:

  Node... type: hybrid

  Active... IP routing: No.

  Active... proxy WINS: No.

  ... DNS suffix search list: cable.virginmedia.net

  Ethernet connection to the Local network card:

  The connection-specific DNS suffix. : cable.virginmedia.net

  ... Description: Marvell Yukon 88E8071 PCI-E Gigabit Ethernet Controller

  Physical address.... : 00-1F-E2-59-FF-14

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  Address IPv6 local link...: fe80::d987:5b5b:1123:788% 11 (Preferred)

  IPv4 address: 192.168.0.100 (Preferred)

  ... Subnet mask: 255.255.255.0.

  Lease obtained...: Tuesday, August 28, 2012 21:23:09

  End of the lease...: Tuesday, September 4, 2012 21:23:08

  ... Default gateway. : 192.168.0.1.

  DHCP server...: 192.168.0.1.

  DHCPv6 IOOKING...: 301998050

  DHCPv6 DUID customer...: 00-01-00-01-12-A7-05-A8-00-1F-E2-59-FF-14

  DNS servers...: 192.168.0.1.

  NetBIOS over TCP/IP...: enabled

  Card tunnel Local Area Connection * 7:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Teredo Tunneling Pseudo-Interface

  Physical address.... : 02-00-54-55-4E-01

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 6:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. : cable.virginmedia.net

  Description...: isatap.cable.virginmedia.net

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  I'm going to guess that you have installed McAfee? There was a problem with her recently. Try to uninstall/reinstall.

  https://KC.McAfee.com/corporate/index?page=content&ID=KB76004&ELQ=a20a206709c24aa9ad7bcbfd33282145

  I hope this helps.

• E8350 in Bridge mode allow me access to the router with 192.168.1.1

  I have a small home network with the E8350 (AC2400) and a PK5001A of Qwest ActionTec modem.  I needed to put the router in Bridge mode to enable NAT in the modem works properly.  By simply disabling the NAT in the E8350 network broe. Once I placed the E8350 in bridge mode, I lost connectivity via 192.168.1.1.  The network seems to work correctly, I can't access the router remotely.  Is this normal or is it a different setting I'm missing?

  When you have done this, you probably have a new ip address of the primary router. See what she is looking at the main router connections or by manually adjusting it 192.168.1.2 or some other ip that is in your network. If the primary router uses a different subnet as 192.168.0.x, then you must use an IP also in this same range.

• wrt54gx2 cannot access 192.168.1.1 through

  Even after using the reset button I can't access the wireless router to configure

  have you tried several mcobination of similar numbers

  ideas?

  Discovered my problem. I used the conector ENTRY ethernet to the router when I was trying to connect to the 192.168.1.1

  I used one of the ethernet connectors OUTPUT and she found

  Thank you