NB100 - see network wireless, but unable to connect

Similar Questions

• see the ssid but unable to connect to the wireless router

  I just installed a WRT160N router, I can see the ssid of the network wireless networks but cannot establish a connection with my laptop windows xp or my wify active blackberry...  Could I connect my mac laptop son with no issues... of ideas?

  Thanks for the suggestions, none of them had however.  The solution was to allow the width of the channel must be set to Auto 20 or 40 mhz, selecting only 20 mhz or individually selecting the 40 mhz would not so much my son computer macbook laptop and my IBM thinkpad to connect. But the default configuration which is set would not work. From the manual - yes I have finally checked it...  «Channel width Select Auto if you want that the router to automatically determine the width of the channel proper (20 MHz or 40 MHz) to use, or select 20 MHz only (default) If you want the router to operate Wireless-B and Wireless-G mode only.» For optimal performance, Auto is recommended. »

• Connected to a router wireless, but unable to connect to the internet

  I am connected to a Jack of cisco with signal strength excellent on a HP Pavilion DV4000 with a XP SP3 operating system.  He was working a week before a customer visit when someone does something to connect to the system of wifi for this client's Office.  Now, I am connected to my hom wifi system very well, but can not get online.  I tried ipconfig renew & release without result.  Any suggestions?

  Thank you!

  Use the Cisco connect software that was shipped with the router. Install it on your HP and run it. Who is likely to be the best way to solve this problem.

  Best regards

  ERICO

• Computer shows it's connected, but unable to connect to the Internet

  Original title: also connected but unable to connect

  I have a HP Pavilion a1710n 64 Dual Core Processor running Windows Vista Home Premium.

  The computer shows that I am connected to the internet, but I can't connect to IE or firefox.

  My Internet Protocol Version4(TCP/IPv4) properties shows that the two buttons marked for obtain an IP address automatically as well as the use the following DNS server address.

  My network card is NVIDIA 10/100/1000 Mbit / s, and the computer shows that it works correctly. I tried to do a back roller and re - put to date but still the two marked buttons.

  Large number of background information...

  I was trying to understand why the windows installer did not work on my son's account. I went in systems and changed to start and automatic manual. Rebooted PC and the firewall do not come. Tried to do a restore, but failed and lost all my restore points.

  At this point, I lost my internet connection to know after vainly trying to figure out the problem I contacted an ATT(my internet server) of things ATT me had to do was change the properties to get the use of a DNS server address automatically and had typing me the address. After reviewing the many things ATT concluded there was not a problem with my connection and the PC is configured correctly and suggested that I should speak to technical support and of course, it was not free.

  Tech support determined there was something that crashes me to connect to the internet and had run me malwarebytes. He detected 24 traces of adware and 2 traces of a virus in the registry database. I deleted everything and still no connection to the internet. Next Tech had me run Combofix and says everything should run fine after that. Still no connection to know Tech # 3 had executed me guests of orders with ping commands. Finally, he had me check the auto config button and that's where I discovered the two buttons were lit. Tech said "can't be." Well it is. That's when I tried to roll back the driver, but no luck so tech says only option is to restore the whole system.

  GRRRR... After several internet searches that I'm about to do except nothings saved and whenever I try to use my backup and restore fails.

  Any help would be appreciated. I'm still fairly new to PCs so please be patient with me. Laughing out loud

  I know that my options have been counted, I was able to save what was important and made a full system recovery. I am happy to say that I'm back on the internet.

  Thank you very much for your help and support. I learned a lot on my computer, as well in location wonderful are the microsoft forums :)

• Can connect to the server (although very slowly) but unable to connect to the internet

  Original title: network connectivity

  I have a user who has been connected to the internet through our SBS server.  All of a sudden, it can connect to the server (although very slowly) but unable to connect to the internet.  The network and sharing shows that it is connected to a public network not by the domain server.

  I hooked another computer for network wiring and it worked fine.  I changed the wiring, and it still doesn't work.

  Any ideas?

  Thank you

  This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers)
  *

  http://social.technet.Microsoft.com/forums/en-us/home s/fr-U.S./Accueil
  http://social.msdn.Microsoft.com/Forum
  
  
  If you give us a link to the new thread we can point to some resources it

• Bluetooth android smart pairs of phone with pc but unable to connect to each other.

  Original title: Bluetooth pair android smart phone with the pc but cannot connect between them.

  My smartphone HTC android on s one can be paired with windows 7 based sony viao laptop but unable to connect between them for any other action.
  How can I connect my mobile with my pc using bluetooth?  Waiting for a response. Thank you in advance.

  Hello

  1. what exactly are you saying then?

  2. do you get any error messages?

  3 did you do changes on the computer before the show?

  4. What is the model of the phone?

  I suggest you to see the site mentioned below:

  Change settings for a Bluetooth compatible device

  http://Windows.Microsoft.com/en-us/Windows7/change-settings-for-a-Bluetooth-enabled-device

  I also suggest you get help from HTC on the site mentioned below:

  http://www.htc.com/us/support/.

• I cann't get the network wireless hp 7500 to connect. I use wep-64 and shared.

  I cannt get the network wireless hp 7500 to connect. I use wep-64 and shared.

  I'm glad it's working for you now.

  Thank you to inform the community that has solved the problem.

• problem of bluetooth of Windows 8. Phone paired but unable to connect, says Windows phone in offline mode

  Problem of bluetooth of Windows 8. Phone paired but unable to connect, says Windows phone in offline mode

  Somasundaram Mohammed. Thank you for your help and maybe you will pass on the solution to all those in need. All that is necessary is to download Bluetooth Stack Toshiba 9.10 and run it. However be careful because version 9.0 of battery is not compatible. I have now my two Android phones connected.

  Thanks again

  John harney

• Computer can see wireless but does not connect

  I have a new HP EliteBook Folio 1040 G1 running under Windows 7 64-bit. The computer can see the wireless network, but when I try to connect to them I get a pop up saying "Wireless: assocaiting" followed by a saying "Wireless: disconnected" and the connection never works. In this case connect to any wireless network. I know that networks and passwords are correct, because my phone and iPad can connect to them without problems.

  I've updated all the drivers via Windows Update and also the SP support Assistant. I tried to uninstall the wireless driver and allowing windows to discover and install from scratch. Nothing seems to work. I see a similar thread a few years ago in the forums but no resolution. I never got so so boredom before wireless connection and I can't help but suspect a hardware failure.

  Can anyone suggest anything?

  Thank you

  Phil

  OK, I realize, but this cannot help others, after raising a warranty with HP call, it turned out that my problem was hardware after all. HP sent a technician to replace the network card, but when he opened the laptop, it turned out that the antenna is detached from the card wireless altogether and reataching it solved the problem.

  Like I said, probably not much help to anyone because it was a specific question, but I thought I would post the result anyway.

• I can not connect computer vista laptop to my network home, but I can connect to other networks. Other computers can connect to my home network very well. This can be corrected?

  My laptop runs Vista and I've not had problems connecting to my home network wireless until a week ago or not.  Then, trying to connect, I see other available networks, but not my own.  When I try to connect manually, it says that the network already exists.  Other computers, macbooks, are able to connect to my home network without problem.  I am able to connect to a network on my laptop fine unsecured wireless.

  I could 'solve' the problem or get reconnected with a restoration of the system to an earlier date, but it only lasts a day or two.  I searched for another fix and tried many things, including to reset the router, remove my network, and then reinstall, etc, but can't seem to get this to work as if it were - automatic connection as the first network.

  Any help would be appreciated.  Thank you.

  You have rebooted the router and the pc at the same time?

  You run the IPCONFIG / all from a cmd prompt can and download a preview of the output to a file share services like rapidshare and put a link to it in your next post?

• Satellite L300 - 17L - don't see networks wireless detected

  Hi all

  I just bought a Satellite L300 - 17L. All drivers seem to work except for the wireless card.

  First, I installed the driver indicated by this site, but I discovered that the map is actually a card Intel Pro 3945, not Realtek as specified in the section of the driver.

  Now I have installed the driver for the INTEL PRO 3945ABG, 11.5.1.15 version and also the PRO Set utility, and I do not see the networks wireless detected.

  I have a colleague who sees many networks using the same card but on another laptop.

  I also tested the switch on the laptop and it's on.

  Have you experienced these problems on your system? Please help me because I am really sad because of this problem.

  Thank you & best regards
  Valentine's day

  Hello

  As far as I know this laptop was equipped with the Intel 11 a/b/g WLan card.
  You should first check if the WLan router and wireless network cards use the same WLan standard.

  In the properties of card WLan (in Device Manager), you can check this settings, choose the Advanced tab.

  I would recommend also check if the WiFi network was activated properly

  Good bye

• Can ping cRIO but unable to connect to the MAX

  I have a cRIO 9066 put in place on a local subnet. I think that all the software and drivers are correct. I have deployed my program and it works great except... When I add some optical converters of fibre in the mixture. Here is my system:

  PC--> cable ethernet--> ethernet switch-->--> cRIO ethernet cable * it works fine *.

  PC--> ethernet cable--> converter of fiber--> fiber--> ethernet switch (FPS)-->--> cRIO ethernet cable * unable to connect to MAX *.

  When I connect with ethernet cables all the way through, the ping time is<1ms ttl="" is="" 64.="" when="" i="" add="" the="" fiber="" converter,="" i="" can="" still="" ping="" the="" crio="" but="" ping="" time="" goes="" to="" ~250ms="" and="" ttl="" goes="" to="" 247.="" then="" max="" can't="" connect="" to="" the="" crio.="" is="" my="" connection="" speed="" too="" slow="" for="" max="" or="" the="" crio="" to="">

  My converter fiber and ethernet sfp module switch are all 1000 MB/full duplex. It is run only on a 10 m fiber. I tried several fiber optic cables. I tried the sfp in several locations. My sfp and the switch are both Advantech so I guess that they are compatible with each other. At this point, I plan to buy just a card PCIe fiber for my PC, but I thought I should check first with the experts.

  Thank you

  Hello

  There is a timeout OR max. The default value is 4000 Ms the reason why you are not able to detect the cRIO in NOR-MAX may be because the packages are damaged along the way. If you do not want to check this, you can always monitor the packets with WireShark with two different sets high. In this way, you can see if the packets are defined correctly or not.

  I hope this helps!

• WRT54G good signal wireless but no internet connectivity.

  I have a WRT54G that has worked well for about a year. Last Sunday, I installed a couple of small updates from Microsoft on my main computer (cable via an ethernet cable from the router). At the same time, I installed service pack 3 on my girls (wireless) counter top.

  Since that time, on my three computers wireless I shows the strength of very good signal from the router but no internet connectivity. Internet works fine on the computer by cable.

  I have reset the router, no luck. Updated the firmware, no luck. Released and renewed until the cows came home and still no luck.

  I uninstalled the router of my main computer and reinstalled. During the installation it tells me that the router cannot find the internet even if the computer that works is connected through the router.

  I tried a different router (even part old version) which was a router to work when uninstalled about six months ago. I went through the installation process and it is the same, the router cannot find the internet.

  Is it possible to have two bad routers that the internet can pass through but the router cannot detect?

  At first I thought changing the setting of the Microsoft updates, but I restored my computer to a date before the updates and still have the same problem.

  Any help that anyone can give is most appreciated.

  Well there are some knows the problem with Service Pack 3 from Microsoft with wireless connectivity. You can uninstall SP3 from your computer and it will not solve the problem.

• I can see PC 'A' on a home network wireless secure PC 'B' but unable to connect; path error

  On PC 'A' I see 'B' PC and connect normally.

  PC 'A' is under Vista Home Premium; 'B' PC is running Vista Home Premium 64.
  Both systems have all the Windows updates current.

  This problem occurred after a repair and a reinstall of the OS/OEM on PC 'B' disc image  I have studied many guides of troubleshooting and everything seems to be in order.  Name of the Working Group, sharing files, exploration of the network, etc. are all correctly.  Shared folder names and computer names follow rules.

  I tried with, on and outside of the firewall.   I also tried to disable the anti-virus protection on both computers.

  The PC normally inaccessible 'B' appear in the router admin utilities.  No, there is an IP address conflict.  The drivers for my PC 'B' wireless card and the router is up-to-date.

  I tried to reboot the computers and the router and the modem without effect.

  I also tried remove the 'B' network and setting up again from scratch.

  Wireless signal is very strong, and I have no problem with internet on two PCs.

  I get the error message is so common that it is very difficult to sort through research on the internet; almost all subjects deal with the problem between different OS.  Here is the error message.

  "Check the spelling of the name. Otherwise, there could be a problem with your network. To identify problems with your network, click on diagnose.

  More > error Code 0 x 0070035 the network path was not found. »

  I have exactly the same problem with a 'C' also running Vista home Premium netbook.  'B' is displayed in the network, but are not accessible.

  Here's something that might be a clue: in the network, the computer 'B' is empty in the column: "network location".

  Is someone can you please help me understand this?

  Hello

  1. you are running Norton 360 on your computer?

  If so, I suggest to turn off the Norton firewall or configure it to allow other computers to connect.

  Also I suggest you to check the following services and ensure that they are enabled:

  Client DHCP (Dynamic Host Configuration Protocol).

  b. (Domain Name System) DNS Client.

  c. Server,

  d. support TCP/IP Netbios (Transmission Control Protocol).

  PING each computer by its Internet Protocol (IP) address, and if successful, PING by name. You can get the IP address of a computer by opening a command prompt (DOS window) and type IPCONFIG, follow these steps:

  a. click "start".

  b. on the box, type "cmd".

  c. on "cmd", press enter

  d. window will appear, there type "IPCONFIG".

  I hope this helps.

• Update wireless network errors, but everthing else connects very well

  I have a BDP-S3100 that always gives me the following error message when I click on "network update": "

  "The State of the connection cannot be confirmed.  Unable to communicate with the server. Please try again later. »

  I have a wireless internet and other applications work fine.  Network connection status shows the wireless connection and the Internet like OK.

  I guess I need to update the network function of work in order to update the firmware if necessary and receive alerts when a new update is ready.  I was very upset to find my firmware was outdated and I had to burn a disc to manually update a Sony's Web site download.  So far, this isn't a machine that is easy to use, and I feel bad for the owners 'mom & pop' who have no idea how to install an update manually.  (You Tube would not work until I did the update).

  As all other wireless connections work fine after the last firmware update, anyone know why the "Network Update" feature is always a failure?  I hope that this is the Sony side, things, and they have server problems. But I fear that if this is the case, no one at Sony is aware of it.