NB10t-A-101 power problem

Similar Questions

• Satellite NB10t-A-101 - problem with graphics card Intel using Win 10

  After I upgraded to Windows 10, The graphics card worked fine, at least 4 months later, I saw that the Intel Graphics tray icon was missing when I went into device manager he had a small exclamation mark by it and said

  Your computer's system firmware does include enough information to properly configure and use this device.
  To use this device, contact the manufacturer to obtain a firmware or an update of the BIOS of your computer. (Code 35)

  Then, I looked a little further into the problem and found this:

  Problem code: 00000023
  The problem: the resources for this device in conflict with the MCFG table.
  C0000908

  I have not edited the PC somehow, any solution to this problem
  Specifications of the PC (if needed)

  Model - NB10t-A-101
  Processor - Intel Celeron n 2810 @ 2 GHz
  Graphics card: Intel HD Graphics.
  RAM - 4 GB

  (Another note: I need the last generic graphics driver for Windows 10,)

  If Win10 supports the Intel HD graphics chip, a driver will be available in Windows Update.

  Check if your HD from Intel is compatible:
  http://www.Intel.com/content/www/us/...000005526.html

• Cannot start OSs of HDD external USB on the Satellite NB10t-A-101

  I'm unable to install Linux on the Satellite NB10t-A-101, because it does not allow to boot from USB or install other OSs.I tried to circumvent this way: (it came with pre-installed Windows 8).

  (1) turning off SecureBoot (which I did)
  (2) putting USB at the top of the list of starting the computer.

  But it does not work.

  I have two HDD USB (a TPG, the other normal) partitioned and it s impossible for them starting with this model of Satellite. I m thinking to return it back to the store that I need to install/start several OSs.

  Hello

  Great that you are using Linux on your PC!

  You mention that you have disabled the secure boot.
  It is very good. But you don't say anything about the startup mode and nothing about what Linux you try to start.

  Most of the distros must support UEFI but that can't be true for each of them.
  If you want Win8 dualboot with a Linux distro, so you need to active UEFI and able to start in this mode distribution.
  If you use a late clone-Ubuntu, Fedora or OpenSuse, you should be fine!

  Another clue could be to take the USB key and try to start another PC from him.
  Which will give a clearer picture of where the problem lies: on your key or the compatibility of firmware NB10 & distro Linux of your choice.

  If you try to boot from a USB - HDD, I'm afraid I'm a bit at a loss as I've never tested.

  I hope this helps!

  Tom BR

• Installation of Ubuntu 14.04 on Satellite NB10t-A-101 does not work

  Hello world

  Sorry for my English: it is not my mother tongue. I'll try to explain my problem.

  I would like to install Ubuntu 14.04 on my computer (Toshiba Satellite NB10t-A-101), but it does not work.

  I boot on my USB (made with RUFUS), but it works once for each five times.

  After you install the operating system, when I restart the system, the computer does not find an operating system (I precise that I already check the EFI BIOS and disable secure boot)

  How to install Ubuntu?

  Hello

  This series of portable was equipped with a processor Intel Celeron 2810 n and this CPU belongs to the new Intel BayTrail platform.

  The * Intel deposit path * allows only the installation and utilization of systems capable of UEFI as Win 8 or 8.1 Win

• Tecra R840-S8450 - power problems - help with Blink Codes

  Looking for help, thinking on the right track, but want to confirm and get things fixed.

  Have a Tecra R840-S8450 that is having power problems. When you try to start it, the orange plug light flashes a code. This code is 01001010 which I derived shortlong short short long short long short flashes of orange electric light.

  It is great progress, assuming that I have translated as right to 52 h, which is equivalent to 'EVER5V voltage is under or equal to 4.5V when the computer is '.
  Start ". However it don't tell me what is wrong so that I can try to do something about it.

  Would be grateful for the help, thanks,

  David

  Of course quite here, is that no one from Toshiba has the manual to find codes?

  Posted by dgwbdavid
  

  Looking for help, thinking on the right track, but want to confirm and get things fixed.

  Have a Tecra R840-S8450 that is having power problems. When you try to start it, the orange plug light flashes a code. This code is 01001010 which I derived shortlong short short long short long short flashes of orange electric light.

  It is great progress, assuming that I have translated as right to 52 h, which is equivalent to 'EVER5V voltage is under or equal to 4.5V when the computer is '.
  Start ". However it don't tell me what is wrong so that I can try to do something about it.

  Would be grateful for the help, thanks,

  David

• Satellite NB10T-A-101 - mouse pad does not work

  I have a touch screen for Toshiba Satellite NB10T-A-101, the touch screen works very well but I use mostly the mouse pad I find using the slider easier.

  But recently my guarded cursor freezing for a second or two and then to spend once again, but now the mouse pad seems not working with the left and right click buttons work but not the touchpad.

  I made sure the touchpad is enabled in the mouse settings, so I don't really know what to do now.
  Any suggestions would be greatly appreciated
  Thank you

  Hello

  Have Hmm you also checked the FN + F5 key combination?
  This would enable and disable the touchpad as well.

  But from my point of view, it would be possible that the touchpad module is malfunctioning.
  I m thinking about the hardware malfunction because the touchpad buttons work and just touch the touch work area module doesn't correctly.

  Usually, if the touchpad would be handicapped by any software, both; as well as the touch buttons does not work.

• Re: Satellite NB10T-A-101 - cannot boot from USB key

  Hello

  I bought a new Toshiba Satellite NB10T-A-101 and want to improve performance by changing the HDD with a SSD and install windows Pro 8.1.

  However, I am unable to boot from USB, it always mention:
  + Reboot and select proper boot device or insert boot media in selected boot device and press a key. +

  I already disabled secure, used 5 + usb startup different sticks (work fine on other laptops).

  Can you please tell me what the approach is to change the HARD drive and then boot from a USB bootable (UEFI).

  Thank you.

  Hello

  Laptop Satellite NB10T-A-101 was equipped with an Intel CPU 2810 n which is part of the new Intel Bay Trail-M platform.

  This new technology Intel Bay Trail allows installation of UEFI capable systems:
  Win 8 or 8.1 Win

  Just a few questions:
  Have you already changed the HARD drive to SSD drive?
  If so, the new SSD is recognized in the BIOS?
  Have you tried to boot from the USB flash memory stick 8.1 Win until you changed your SSD drive?

• On the Satellite P30-131 power problem

  I have a power problem and I tried the process of elimination, but could do with help, I gave as much detail as possible and appreciate any help or advice.

  This started a few weeks ago and seems to be deteriorating slowly.
  I turned on the laptop and all 3 lights before the main power on fully charged battery light and light green...

  I started noticing a few times when my power cord is plugged into the laptop that, without warning, the laptop switches to the battery power and also turns off power light, battery light turns off too but which may or may not happen, in any case the laptop is still on but now running on battery.

  I then out of the supply cable and reconnected it hoping that power is restored, but it has no effect, I have to close then low laptop unplug then Pug back in and I get all 3 lights and then I can start.
  Now, when I boot it does not always solve the problem and I can finish on a few seconds of starting battery.

  Its certainly not the battery because it has a new battery replaced 12 months however, its either the adapter or the connection inside the laptop that plugs into the adapter.

  The reason I think it is perhaps one of them is when the laptop going to battery, lead that is always plugged into laptop, I moved, and this can cause the return of t lights and also the laptop back in, power once again, but if I let go then it goes to the battery again one the light turns off. I also took the battery out and kicked and the laptop works but has lost the power sometimes when I moved it turned off my tour so I'm sure that it is related to the lead, but do not know if its internal or external.

  Any help or advice appreciated

  Thank you

  What kind of help did you expect exactly?

  > Its certainly not the battery as it was a new battery replaced 12 months however, its either the adapter or the connection inside the laptop that plugs into the adapter.

  It seems you have tested everything that could be tested using common control procedures, I think that more is not possible
  I can provide also a few suggestions and I m coming to the conclusion that neither electronic power supply is not ok or your power adapter.
  But I would tend to the first; electronic power supply.

  As you can see that these are only suggestions

• Power problems: computer turns off when the power supply cord is unplugged.

  original title: power problems: computer shit turned off when the power supply cord is unplugged.

  I have a HP Pavilion dv2000

  Windows vista home premium/sp2

  AMD Turion (TM) 64/2 1.80 ghz processor

  1 GB memory

  32 bit operating system

  I have 2 problems with this laptop.

  !. I have lost the power cable and bought an expensive one online step (model: PA-1650-02 c. input 100-240v 1.5 put out a(1,5A) 18.5V 3. 5 = a)

  When I first plugg cord battery charge light came on the balance, then he started to come on and outside.

  now its completely off, even with the power cord plugged in. on the lower right part of the screen its showing that cord is connected to the power supply and the battery is fully charged, but as soon as I unplugg the power cord or remove the computer cut right away.

  the second problem is that the left mouse botton does not work, the work aside right very well. I went in the proprties to put it right, click on to, but who does not work either. I've updated the drivers but still nothing.

  Any help will be greatly appreciated.

  Hi aloum,.

  (a) what kind of mouse you are using?

  (b) the left button of the mouse seems to be stuck or it does not meet the click? This only happens with certain applications?

  Step 1: Test the mouse on another computer or another mouse on the test computer

  To determine whether the mouse or the computer is defective, follow these steps:

  1. test the mouse in question on a system that works, you know. If the problem appears to follow the mouse, you may need to return or replace the mouse.

  2 test a mouse you know is working on the computer in question. If the problem seems to stay on the computer, then the problem is most likely related to the software.

  In regard to the battery not holding charge

  Battery problems are often associated with the battery itself. If you encounter this problem, contact your mobile PC manufacturer. If you purchased the battery separately from the notebook computer, contact the manufacturer of the battery.

  Troubleshooting battery problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-battery-problems

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• possible power problem

  Hello

  I have a desktop HP Pavilion 7865 has started to give me some power problems.  I followed the troubleshooting steps to

  http://support.HP.com/us-en/document/bph06788#n414

  The first time it's happened that I noticed that the power light little would go as I connect the power cord to the back of the unit.  But the little green light and then returned.  After some tests, the power light remained on and I was able to turn on the pc.  However, it started again this morning so I finally took my monitor power cord and used this one to connect the power supply to the back of the computer and to a power outlet and it works.  I plug the pc power cord into the monitor and my monitor works too so I don't know if it is or is not the power cord, but I'll go out and get a new one and see if that solves all my problems.

  However, my question is this... If the problem is with the power supply that I plug in can be replaced?  If so, it is something I can do myself or should I consider somewhere to do?  Also, if I need to replace the power supply and I can do it, how can I know what type of replacement power supply unit power I need to get and are there any other cables that I also need?

  Thank you so much for all your help.

  The information I found States 7865 HP is a Win98ME around 2001. The stock PSU is a Bestec 200W.

  Form factor is Micro ATX PS3. Here's a picture: http://www.911forpcs.com/7865.html

  If your going to replace the power supply, you must perform steps. I found a contradiction Newegg.

  Micro ATX

  http://www.Newegg.com/product/product.aspx?item=N82E16817338031

  http://www.Newegg.com/product/product.aspx?item=N82E16817104113

  PS3

  http://www.Newegg.com/product/product.aspx?item=N82E16817338005&cm_re=ps3_power_supply_replacement-_-17-338-005-_-product

• Problem starting the BIOS NB10t-A-101

  I just bought a NB10t to the United Kingdom and try to boot to a bootable USB key

  I noticed that the BIOS on this particular model is UEFI mode only, which, in itself, is not a problem because users can sign their own operating systems with a certification authority and use them, but this laptop refuses to boot from any external environment... or even to provide an error message.

  I changed boot priority in the BIOS and USB moved up
  I disabled the Secure Boot option in the BIOS
  I tried all 3 USB ports as well as 3 different drives (NOTE: THESE WORK FINE ON the 3 OTHER SYSTEMS, a dell desktop/laptop computer and a computer acer laptop)
  I also tried different distributions (Debian & Arch)
  I used several installation methods (hard install of Unetbootin/Full/Rufus etc...)
  I tried all your currently released BIOS versions (delivery with V1.0, V1.1 - Jan Feb - V1.2)

  After trying all these when you press F12 at startup, the shows start menu but when you select a device, the system continues to initiate (Win8) HARD drive
  After Googling around, I noticed that you have unlocked 2 BIOS updates I tried all versions of these and still the system refuses to boot in my selected device

  Can we expect more updates of the firmware in the near future? Is there a way to work around this problem to start my chosen OS? Is there an option of CSM?

  The laptop can be started from an external source such as USB flash memory stick but make sure of a few important points:
  A few tips:

  1 - USB key must be in the right port (USB2).
  2 - USB key must be UEFI-bootable (a Debian or Ubuntu, Installer copied on the USB stick with 'dd', is very well).
  3 - Bootloader file must be named boot/bootx64.efi (again, a picture of the Debian or Ubuntu installer will be already OK).
  4 - now try the ESC key before and during hit the power button, to select the boot device.

  Here, I found another thread on this topic:
  https://Forum.Toshiba.EU/showthread.php?75759

• ".dll" and problems with my satellite A30 101 Power Saver

  Hello world

  Who can help me, I have two doubts. The first is, I don't always get on three messages when it starts. Will take you to my second problem. The power mangement. It is said 'E-Power Power Management' when I click ok, another message comes to say, '... No data. The Toshiba Power Mgmt system is no longer appearing in the Notification bar. It does not work.

  What can I do about these difficulties?
  Thank you

  Dejen

  Hello

  You forget to mention what are the names of the dll-files :). But still, even with the names he cannot drive anywhere. First suggestion: run a full! ScanDisk on your primary partition (usually drive c :)). The lost files could come from the fact that your data are damaged somehow. Second, try to uninstall the Add/REMOVE program section powersaver module in the control panel. After you have uninstalled, try to install again.

  Good luck

  Tom

• Satellite L30-101 power up used

  I have a L30-101 which has unstable power supply problem.

  Sometimes it will start without effort. Once I press the power button, load cookies and wifi will be off and the power light will flash briefly, after that a few seconds, the load and wifi lights will be rekindled and I can try again. Finally, if it is not started, the light goes off and that's all.

  another time if I push the button for a few seconds, it will start or freeze as noted above.

  To try again, the only way is to remove the (new) battery and the power cable.

  Also, I tried to hold the power button down for 30 seconds with the battery cables and power removed as a forum sudgested it discharging the capacitors on the motherboard. Sometimes, it works. Sometimes it doesn't.

  If I have apart and put back together, it works. (but that's a bit excessive. So unless he can sprout wings very quickly, it's life may be limited).

  All these answers are the same whether on the supply cable, battery only or both.

  I'm starting to loose patience...

  Your described problems looks like a motherboard failure.
  I have no other explanation for that matter.

  I mean it s not a problem of battery from the laptop must turn on correctly just connected to the AC adapter only.

  I put t think the related issue of RAM because in this case the laptop must turn on not even for a second or the system freezes after widows started upward.

  Satellite L30 is slightly older unit so it can be possible to this motherboard is the troublemaker.

• Power Mac G5 power problems...

  Hello, on a quest to find a G5 computer, I found an early 2005 Power Mac G5 (2x2.7GHz). The first time I plugged it in and turned on, it works beautifully. The second time, I pressed the power button and heard a loud noise from the power supply. I replaced and this is what is happening now:

  When I plug the power cable in, there is a small clicking noise about a second after plugging in, and the power led on the front of the machine flashes for the click. However, it does not at all depend on when I press the power button. When I unplug the cable, it makes the same noise about a second after I unplug the unit. I see a pale glow of the light output after unplugging it.

  Anyone have any suggestions to solve this problem? It is part of a collection, that's why I want to do operational.

  There may be defective capacitors or other power supply problems, including

  overheating in the dust inside the power supply or air channels. And

  If the device is cooled by liquid, other things may be involved.

  Since all the PowerMac G5 power supplies are considered to be custom,.

  to get a good replacement is a way hoped to improve the situation.

  Unlikely as is, actually an inexpensive job.

  Have you tried a SMC power management unit reset? Or reset PRAM?

  • How to reset the SMU on a Power Mac G5 (late 2004) or Power Mac G5 (late 2005) - Apple is supported

  To reset NVRAM (PRAM) see:

  • How to reset the NVRAM on your Mac - Apple Support

  Several links appear in the result of this research; some look promising:

  https://DuckDuckGo.com/?q=Troubleshooting + G5 + PowerMac + power + supplies& t = ffsb & AI = web

  I read about the noise, the PowerMac G5 can do when some power components

  fails; Troubleshooting is involved. Somewhere I had a link to a source for official PDF
  REPAIR, download for offline use. -I do not see if I can locate the item...

  Apple Power Mac G5 (early 2005) manual .pdf

  Apple Power Mac G5 (late 2005) manual .pdf

  Apple Power Mac manual G5.pdf

  Good luck!

• Satellite NB10t-A-101 refuses to boot from any external media

  I just bought a NB10t to the United Kingdom and try to boot to a bootable USB key

  I noticed that the BIOS on this particular model is UEFI mode only, which, in itself, is not a problem because users can sign their own operating systems with a certification authority and use them, but this laptop refuses to boot from any external environment... or even to provide an error message.

  I changed boot priority in the BIOS and USB moved up
  I disabled the Secure Boot option in the BIOS
  I tried all 3 USB ports as well as 3 different drives (NOTE: THESE WORK FINE ON the 3 OTHER SYSTEMS, a dell desktop/laptop computer and a computer acer laptop)
  I also tried different distributions (Debian & Arch)
  I used several installation methods (hard install of Unetbootin/Full/Rufus etc...)
  I tried all your currently released BIOS versions (delivery with V1.0, V1.1 - Jan Feb - V1.2)

  After trying all these when you press F12 at startup, the shows start menu but when you select a device, the system continues to initiate (Win8) HARD drive

  After Googling around, I noticed that you have unlocked 2 BIOS updates I tried all versions of these and still the system refuses to boot in my selected device

  Can we expect more updates of the firmware in the near future? Is there a way to work around this problem to start my chosen OS? Is there an option of CSM?

  Edit: punctuation

  null

  Hello

  Your laptop was equipped with the new processor Intel Celeron 2810 n that belongs to the Bay Trail-M architecture.
  This new * Intel Bay Trail * technology is only supported systems that support UEFI and systems (Win 8, 8.1 Win) and, therefore, the UEFI / CSM boot mode option isn't available in the BIOS settings.

  _So you can install only a system capable of UEFI

  PS: The same topic has already been discussed in this thread:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=75041