NETGEAR WNDR3400v3 N600

Similar Questions

• WNDR3400V3-N600 - connectivity problem Windows 10

  Hi, I have a new DELL Inspiron (Windows 10) with a 'Intel Dual Band Wireless AC 3165"which is impossible to connect to the router N600-WNDR3400V3. Other existing devices like Android, iOS, and printer are connected through the router and work very well. I get the message "Check network requirements" and a moment later get "unable to connect to this network. The wired connection works fine. I have disabled access and even control tried to 'None' security briefly. But, without success. Also connected to an another non-NetGear router wireless connection earlier, which suggests that the problem is specific to the environment of NetGear.

  Driver for the adapter - the most recent version Intel (18.20.0.9)
  S/w - latest Version (V.1.0.1.2_1.0.51) router

  I even stepped back to previous versions of the Intel adapter like 18.12.0.3 & 17.15.0.5, but without success.

  Any help is appreciated. TIA.

  Found the problem.

  Once I had updated the firmware on the router sometimes, back needed me a hard reset of the router. Everything is back to normal now.

  This can be closed now.

  Thank you Elaine, for your support.

• WNDR3400v3 (N600 router) cannot recognize all printers on Readyshare

  Hi, first time announced! I just bought a N600 (WNDR3400v3) router and has difficulties with ReadyShare.

  -J' was able to connect an external to the router and I can access through my computer!

  -However, both printers I've tried to connect have not been recognized. They are a HP1006 and a Brother DCP 7040. On the routerlogin.net and soft Netgear engineering, say that there is just no USB not connected under the section ReadyShare. When I open the control center USB Netgear, I don't see any printer listed.

  Any thoughts? Is it possible that BOTH printers are incompatible with this router?

  Thank you!

  Davis

  I apologize, I thought wrongly that you have WNDR4xxx

  The WNDR3400 isn't compatible ReadyShare Print.

  See thisarticle for more information. Supported routers are listed on the right side of the article.

• NETGEAR wndr3400v3 can not play you tube videos

  Hello, I have recently set up my router wndr3400v3. Everything works well with the exception of not being able to watch videos tube.

  When we try on any of our devices... phones, iPad, computers laptops you tube time limit and do not play. Not sure if I missed something in the configuration. Any thoughts would be appreciated. We have a wireless setup using ed as our provider.

  Hello @tigertribe

  Welcome to the community!

  You had nothing under block sites do you have?

  How about no matter which set of Parental controls?

  If still nothing, I suggest that you reset the router and everything again.

• Chromecast - Airport Extreme: not casting

  Hello everyone, so I bought a new rMBP and I also had to get the Airport extreme combo all the experience.

  I have a 2015 rMBP, Airport Extreme, Apple TV, iPhone Chromecast 6, laptop computer Dell Windows 10 & 1320c Dell Color Laser printer.

  I've never had a problem before, but after I installed my new router (AE) and connecting all my devices, I do not see tab cast in any of my applications of melting of chrome.   I wonder if apple don't just market talk to chromecast.

  Really, I don't want to have to buy an another apple tv for the living room, I'm fine with the help of the chromecast with my laptop and other applications. Can someone please shed some light on this situation?  I need help and have exhausted all my resources and have not been able to find anything online in reference. Keep in mind, I am very Tech savvy and never had this kind of problem before. So everything is correctly connected, connected, and put in place. Just can't go to my chromecast.  What is a block from the Airport extreme? because it works very well with my Netgear WNDR3700 N600.   Thank you, I appreciate any help on this.

  ---------

  Please check previous post and my reply. He always refers to your question. The only difference is that Google updated list routers include the A1408 AirPort Extreme... which is still not compatible with Chromecast.

• Windows XP Pro, and WPS

  Hello

  At home, I have a windows desktop computer 8, a windows xp pro laptop, a 8 and a windows phone fire HD Kindle.

  Everything is connected to my netgear WNDR3400v3 router and works fine except for my windows xp computer laptop pro.

  The connection speed of the laptop that is located in my basement is very low, so I bought a netgear Wireless extender WN2000RPTv2.

  The extender works with everything in my house except windows xp computer laptop pro. I was told that this is because windows xp do not support the last connection of wifi security type.

  I don't know about you, but I think it's wps or wpe and wpa?

  So my question is, can someone tell me if Microsoft have some sort of patch or update that allows windows xp pro to connect to the last security wifi out there?

  Thank you

  FWIW... It could be useful.

  http://support.Microsoft.com/kb/815485

  Hotfix for Windows XP support for Wi-Fi Protected Access.

  (Read the Details section of the link below)

  http://www.Microsoft.com/en-US/Download/details.aspx?ID=3914

• Confusion about the requirements for the 2015 CC software

  I currently have Windows 8.0 (64 bit) which is so satisfactory and stable.  I have not upgraded to 8.1 Windows because I can't install same normal updates for Windows 8.0 without experiencing freezes system that only restore points can heal.  So for now, I would stick with what I have.  But the problem is the confusing requirements for various programs within the pile of creative cloud applications:

  Premiere Pro: Microsoft Windows 7 Service Pack 1 (64-bit) or Windows 8 (64-bit)
  Photoshop: Microsoft Windows 7 with Service Pack 1 or Windows 8.1

  Illustrator: Microsoft Windows 7 with Service Pack 1, Windows 8 or 8.1 Windows

  Dreamweaver: Microsoft Windows 7, Windows 8 or 8.1 Windows

  Hearing: Microsoft® Windows® 7 with Service Pack 1 (64-bit), Windows 8 (64-bit) or Windows 8.1 (64-bit)

  So what I'm confused about is the fact that Windows 8.0 is not listed for Photoshop, but Windows 7 and Windows 8.1 are.  Does this mean Photoshop CC 2015 is not compatible with Windows 8?  And that means that Premiere Pro is not compatible with Windows 8.1 since only 7.0 (SP1) and 8.0 are listed, I would have preferred the upgrade of software CC WITHOUT update Windows since I am picky on my installation of Windows 8 stable pipes now solid as a rock.  Fortunately, Illustrator, Dreamweaver, and hearing are compatible with all three, it seems.

  Can someone clear up the confusion, please?

  I think that my hardware is OK for this.

  Motherboard: Asus Crosshair Formula V-Z (AMD 990FX)

  CPU: AMD FX-6300 Vichera 3.5 GHz

  Memory: 16GB Kingston HyperX DDR3 2133 MHz

  Video: MSI N650-MD1GD5/OC GeForce 650MX

  Monitor: Acer S271HL of 27 "(1920 x 1080)"

  Power supply: Seasonic X-Series 1050W (SS-1050XM Active PFC F3)

  HDD1: Western Digital 320 GB (System)

  HDD2: Seagate SV35 Series (ST1000VX000 1 TB 7200 RPM 64 GB OEM)

  VidCap: Blackmagic intensity Pro HDMI

  USB hub: Rosewill RDCR-11005 5.25 "

  UPS: APC Back-UPS XS 1500

  Router: Netgear WNDR3700 N600

  System is NOT overclocked

  It is compatible but not tested.

• Netgear N600-character display

  I have a cool new netgear device:

  NETGEAR N600 Wireless Dual Band Gigabit ADSL2 + Modem Router DGND37v2

  which works very well. I came across some problems with a Slackware Linux computer on the network with strange characters in the section "name of the device. An screenshot is here, the device in question is wired device 2 and should be called "ilium".

  I would be grateful for any help on this...

  Hi Darren,

  Thanks for your reply. Looks like I have found a solution, a fellow slackware user suggested I have try update firmware suggested for the router, and this has solved the problem completely:

  http://www.Andrews-corner.org/images/netgear_upgrade_firmware.PNG

  Andrew

• Connect a HP OfficeJet Pro 8500 to router Netgear N600 loss of internet connection.

  Whenever the OfficeJet printer is connected to one of the ethernet to a Netgear N600 router ports, the internet connection is lost. Internet works without any complications, if the printer is not connected to the network. As soon as the ethernet cable from the printer is connected to the router (or a network switch) the internet connection is lost. If I look at the devices using the Netgear browser interface, everything seems appropriate. The printer uses DHCP and you will receive various IP addresses according to what remains is connected (e.g. 192.168.1.3). I've narrowed the problem to the printer, causing the loss of connectivity internet thie. Attach only my computer to the router (may be an iMac or a Windows XP system), internet works fine, plug the printer results in a loss of interest. Printer works fine and the documents can be printed after you connect to one of the ethernet ports.

  I tried to set a static IP address on the printer (e.g. 192.168.1.100) so that the attribution of a static address with the interface of Netgear using the MAC address of the printer - no approach fixes the problem. Netgear support is perplexed (they have even sent a replacement router, thinking it was defectiive, the two routers show the same problem). I have reset the printer to its default settings in order to eliminate potential conflicts with modified parameters. I also tried to change the speed of the link to something else than "Automatic", nothing seems to work.

  We will define an external static IP and DNS address for the printer.  I think that the external DNS will do the trick.

  -Print a the front of the printer Network Setup Page. Note the IP address of the printer.
  -Enter the IP address in a browser to reveal the internal settings of the printer.
  -Choose the network tab, then wireless along the left side, then on the IPv4 tab.
  -On this screen, you want to set a manual IP address. You must assign an IP address outside the range that the router sets automatically (called the DHCP range). If you do not know the range, change the last set of numbers (those after the last '.') 250
  -Apply the subnet 255.255.255.0 (unless you know it's different, if so, use it)
  -Enter the IP of your router (on the Page of the Network Config) for the gateway.
  -Enter for the first DNS 8.8.8.8 and 8.8.4.4 for second DNS. It's Google DNS. You can choose a different external DNS if you wish.
  -Click 'apply '.

  Now, stop the router and printer, start the router, wait, and then start printing.

  Your router have updated firmware?

• Crash computer after installing Netgear N600 Wireless Dual band Router WNDR3400. My detail of error says I may need to update my BIOS to 8400 has 09 but I can't seem to download the desktop to install.

  My computer crashes after I installed the Netgear N600 Wireless Dual band Router WNDR3400.   I uninstalled and then reinstalled, but my home computer still crashed.  My detail of error says I may need to update my BIOS to 8400 has 09 but I can't seem to download the desktop to install.  Any suggestion?

  Hi JudyWinn,

  If you need assistance for updating BIOS (Basic Input Output System), I recommend you contact the manufacturer of your computer to update the BIOS (Basic Input Output System) & check if the problem persists.

  Note: Changing the BIOS / chipset can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/chipset can be solved. Changes to settings are at your own risk.

  Hope the helps of information.
  Please post back and we do know.

• cannot detect netgear n600 wireless adapter

  I have trouble to install a netgear n600 on a windows 7-64 computer's wireless adapter. I already speak to netgear support, via the India, without help. They were able to direct me to the last 1 hour drive in the efforts in the event of a problem. I have test it on a machine running windows vista and installed fine. I tried several ports on my machine, I know that ports operate. What happens is that during installation it asks to insert the adapter... and is unable to detect its existence. Is there something in windows 7 that would cause the adapter to not be detected?

  Hello

  Is the WNDA3100v2 model number? If this is not the case, what is the exact model number?

  Check out the below mentioned link:

  http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/search.aspx?l=en-us&type=hardware&s=NETGEAR%20n600%20wireless%20adapter%20

  Follow the link below and check if the planned measures facilitate the installation of the device:

  http://support.NETGEAR.com/app/answers/detail/A_ID/18580

  Alternatively, you can contact Netgear online support:

  Here is the link: http://support.netgear.com/app/home/session/L3RpbWUvMTMyMDc2OTIzNC9zaWQvd2tEUm5DSWs%3D

• HP laptop could not connect to the netgear N600 router secure

  New laptop HP MAY connect to the Netgear N600 dual band router if NO guarantee is enabled, but it cannot if security is enabled on that either WPA, WPA2, WPA2-PSK regardless.  It can connect too well if wired (of course).

  I reloaded the drivers and all the usual remedies but not joy.  Also I tried using a USB WiFi adapter with the same result, unable to connect with security enabled.  All other devices connect very well including 2 Iphones, Tablet android, Apple TV, Apple MacBook pro, printer, etc. then it does seem like a router problem.

  Laptop is slightly, around the age of 6 months running Windows 8.  As a temporary workaround I disabled DHCP, security and peripheral isolation enabled 2.4 ghz radio router static address then attributed to the laptop, not a lot of security, but that's all I have.  I moved all devices except a (2.4 ghz only) iphone on the active side of 5 ghz on a different SSID with WPA2.

  It seems that the OS has a problem with the hold of encryption in the stack, or maybe it's a hardware problem.  Whatever it is, it works very well with an open WiFi but died completely when any type of security at all turned on, same WEP.  I arrived at the end of my knowledge here and short of a relatively new machine of retirement or try a full reload of the OS (Win 7 X 64 use), I'm stuck.  It is the only system to win 8 I worked (OS nasty if it is).

  Any ideas or suggestions?

  I know it's late, but there are probably people searching on the net because of this problem just as if I were stupid. I got a new laptop Windows 8.1 and plugged into my router to set up. Worked without problem. I unplugged the ethernet cable and jumped on the wireless, typed in my network key and hop, connected with no internet access or other useful functions. Long story short, eventually work was by using the automatic connection on the router (the one at the bottom that looks like a radio with 2 waves coming out of it) to connect the first time instead of manually typing the password.

  You will need to clear your computer auto-enregistré on the network so that you leave cool to do that. At least, I assume that. My laptop has a dual band wireless card, so I just shot on 5G and serves as my network "expenses. After he successfully connected to that one however, my laptop is now having no problem with the 2.4 G which was faulty in the first place.

  Who knows why he can be configured automatically, but don't let you not type the password yourself. In any case, I hope this helps someone!

• OfficeJet 7210 won't install with Netgear N600 router

  I tried to install my Officejet 7210.  I connected directly to my Netgear N600 router and I have access to the wireless router.  My son's computer CAN find and use it.  Mine can install the printer but it won't print.

  I used each troubleshooting I can find.  The HP diagnostic utilities give me an error message when I try to download them, so they were of no use.

  -I can ping my printer.

  -When I try to add a printer manually, it still does not.

  -The printer is the default printer, and it is configured to share.

  -It is not in offline mode.

  -I have installed and reinstalled all the drivers.

  I don't know what else to try.  I don't know enough about the network settings to know what to check.

  OS: Windows XP

  Printer: Officejet 7210

  Router: Netgear N600

  The printer works correctly with the Windows 7 operating system.

  Please help me.  I'm pulling my hair out.

  Hello world

  I found a solution to my problem, and I'll tell what I did in case it helps someone else.

  I used the standard HP installation discs and I got the printer from the list of printers to my computer.

  I have my printer right click and went to Properties.  Then I went to the Ports.  I went to the HP Standard TCP/IP Port and pointed and clicked on Configure.

  Then I went to my printer and print the Configuration Page to network to find his IP (parameters --> network --> print the network configuration page).

  I went to my browser and put the IP address of the printer (see the list on the Network Setup page).  I got a page with all my settings of the printer listed.

  Then I compared what were the parameters of the printer with the settings on the port.

  In my case, the name of the printer didn't exactly match anything on my network configuration page.  However, if I entered the IP address on the port, the window don't would not accept it.  If I entered MAC (with or without 'HP' in front), the window would not accept.

  This last step is what is different from the advice I've seen in the support of HP, then make a note of this one:

  So instead, I changed my printer in the port name to match what was the name on the Web page under the IP address of the printer (home --> info network --> host name).

  Voila!  My printer works.

  I hope it's clear.

  Thank you

  Julia

• No internet connection with new Netgear N600 DGND3700v2

  I just bought this new modem/router and set up according to the instructions. All lights are to the Green (or blue 5 GHz), but when I tried to open a browser on PC, I can't get a connection. All my cameras wifi in the House (I have 6, 2ipads, 2phones, a PS3 and a PS4) connected without hassle (although the crazy speeds slow sometimes, which never happened on the old stock of the ISP modem). I tried unplugging all the cords, something making the 30 seconds then restart. I did a factory reset (but I can't believe I even had on a brand new out of the box one). The only thing that doesn't work is not is my connection ethernet on my PC.

  I put my old modem on just to check, and it worked immediately. I can't even connect to the internet to connect to routerlogin.net. In the manual, there is an optional facility for fiber internet but our street did not as yet, so I'm always on the domestic substances list, and the DGND3700v2 is supposed to be a modem and router, so I wouldn't need to buy a separate box to connect ethernet to my pc.

  In any case, could I please ask for more help, at least let me know if I should go back and try another brand, or it's a defective machine so I could trade and try another brand new machine. Any advice would be greatly appreciated, thanks, Dean

  DPDM_Ps4

  I would contact Netgear support if you just bought this modem to see if it is a defective unit that they can solve the problems with you and determine whether or not there is. In this case it can be replaced by a just RMA to ensure that you have your proof of purchase.

  http://support.NETGEAR.com/general/contact/default.aspx

  DarrenM

• How connect N600 router wndr3400v3 to another hotspot or wifi ssid access point

  I want to connect to my router to an another ot hotspot or access point ssid to increase network range

  I tried but not found any option

  Help, please

  Ok thank you