Similar Questions

• Network controller not installed

  I have a HP Pavilion tx g6-2230. I installed Windows 7 Professional 32 bit. In Device Manager, its showing that my "network controller" is not installed. I am not able to connect to the Internet. Help, please.

  Thank you...

  Hello:

  Here is the link to the driver, you need to map wireless in your laptop.

  http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=0&prodSeriesId=5229455&prodNameId=5229457&swEnvOID=4053&swLang=13&mode=2&taskId=135&swItem=ob-113862-1

• Network does not work after Windows 2000 SP4 P2V

  It has been a roller coaster get this virtualized machine.

  A little history: this machine is Windows 2000 SP 4 with update Rollup 1. After you install the Update Rollup 1, virtualization tried it and it gets to 97% and then I get the message error "vmware agent has encountered an error. When I try to start the machine, I get a BSOD with error inaccessible_boot_device.

  After reading some discussions fo I found a solution of reconfiguing the virtual machine then it will start. So now, I have a virtual machine that will start.

  Now my problem is that networks do not work. I removed the network card, has added a new, tried static and dhcp, through the Add/Remove programs and uninstalled all the devices HP and Compaq, went into Device Manager and deleted all drivers HP and Compaq or component, rebooted countless times and I am still ending up with no network connectivity.

  The network card on the computer virtual says it is connected and he says is to receive, but not send. It is not pulling a DHCP address and a static address gets no where also.

  I have more than 50 virtual machines so I know this isn't a problem with my network, it must be on the virtual machine itself. I don't know what else to try, and I'm open to suggestions.

  Thank you!

  Have you tried to repair the winsock?

  1. Go in Start > run, type: netsh int ip reset c:\resetlog.txt

  2. Restart your computer and you're done.

  3. Follow the steps below if you have XP SP2 (this only works on windows XP SP2 and later versions).

  4. Go to regedit.

  5. Go to HKEY_LOCAL_MACHINE/System/CurrentControlSet/Services

  6. Click on Winsock and Delete.

  7. Click on Winsock2 and Delete.

  8. Close registry.

  9. Restart your computer

  10. Access the properties of the LAN connection

  11. Click the install button in the Properties window

  12. Select PROTOCOL, and then click the Add button.

  13. Click the disk...

  14. Type C:\windows\inf\nettcpip.inf in the dialog box, and click OK.

  15. Choose from the list of INTERNET TCP/IP PROTOCOL in the list, and then click OK.

  16. Click CLOSE.

  17. Restart your computer. (At this point the Winsock is complete)
      not only avoid this problem from happening in the future, but also
      to make the process much easier you update Windows.)

  Try the following steps: http://support.microsoft.com/kb/837333

• Ethernet controller not installed on Windows 7

  I tried to create VMS on ESX 3.5 using the Windows 7 operating system, but it seems that the ether controller is not supported. You want to know how can I achieve this.

  I have not tried with 'Other' as an operating system, but have successfully created the x 86 and x 64, respectively using '32-bit Vista' and "Vista 64 bit" as an operating system

• Drivers not installed after Windows 7 upgrade

  I have a laptop HP ProBook 6455 b.  Last weekend I just upgraded from Vista to Win 7 Enterprise 64-bit.

  Device Manager shows 3 entries under other devices without drivers for.  I tried to select the option "update driver software", but he could not find the driver.

  Base system device - state poster Code 28, unknown manufacturer, bus location PCI 3, device 0, function 1

  Base system device - state poster Code 28, unknown manufacturer, bus location PCI 3, device 0, function 2

  Unknown device - status Code 28, unknown manufacturer, location is Port_ #0002.Hub_ #0005

  Any suggestions?

  Please help and thank you.

  Hello

  You are welcome

  You must download and install the driver Validity Sensor on the link below.

  http://h20000.www2.HP.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en & cc = us & prodTypeId = 321957 & prodSeriesId = 4174254 & prodNameId = 4174168 & swEnvOID = 4060 & swLang = 13 & mode = 2 & taskId = 135 & swItem = ob-84050-1

  Kind regards

  DP - K

• KB973688 and KB954430 do not install. Windows Update loop on them. they install ever.

  KB973688 and KB954430 do not install.  Windows Update tries to install these two updates, but they never complete the installation.  Tried to install KB954430 manually, but it would not install.   Event Viewer event id 7023 windows module Installer service ended.    Dialog box shows HRESULT:0x800736FD {7B30B69B-036c-b7e0-a06b-d6b9abf34537}.    KB973688 would not install either.  Tried rebooting, shutdown windows update, so I could install by hand.  No updates will be installed.  Help, please.

  This question always took place or simply with KB973688 and KB954430?
  Have you tried manually download and install updates?
  Have you read the known issues with this security update of the section of KB954430 and try the steps recommended?

  Suggest you download and Save KB954430 first . Since you did not specify if the system is 32 or 64 bit.
  If you are not sure which architecture is the system, open System in Control Panel.
  Look next to system type under law to see whose architecture is the system.

  KB954430 for Windows 7
  Windows 7 for 32-bit systems
  Windows 7 for x 64 systems

  Once the download is complete to read this and configure the system to boot .
  Start in what is called a State of cleanliness will ensure that Sophos and printing software (including HP print software) does not interfere with the installation of the update.
  Once you have started own the system, right-click the update registered and choose 'Run as administrator' .
  Accept guests UAC to allow the update to install.
  Reboot the system after installation.

  Is he being always reaffirmed or just KB973688 be already now?
  If KB973688 is the only be reaffirmed, install now while the system is still in the clean boot State.
  That bring them both installed?

  Cancel the clean boot procedure as set out in the KB article , they have or they do not have and please post back with your results.
  MowGreen Services consumer safety update

• updtes does not install on windows xp home edition 2002 service pack 2

  Hello

  After formatting window updtes do not install on windows xp home edition 2002 service pack 2

  Rabindra Nath Nandi

  HOW TO get a computer that is running Windows XP SP1 (a) or install SP2 fully patched after a cleaning
  https://groups.Google.com/Forum/?fromgroups#! msg/microsoft.public.windowsxp.general/quMfqk8Eb94/K93XrUGuZqAJ

  VERY IMPORTANT! => Step #4 links above, making resolution method #2 (No method no. 1) on this page: http://support.microsoft.com/kb/943144

  Tip: After completing the computer fully patched, download/install KB971029 manually before connecting any player external to the computer: http://support.microsoft.com/kb/971029

  More: http://aumha.net/viewtopic.php?f=62&t=44636

• Trust keyboard and aula befire keyboard elight will not install on windows 7 help

  TRUST KEYBOARD ELIGHT AND AULA BEFIRE ARE TWO PLUG-AND-PLAY BUT WILL NOT INSTALL ON WINDOWS 7

  Hello

  1. do you receive an error message or error code?

  2 have you made changes on the computer before this problem?

  3 is the issue limited only when connecting keyboards?

  This problem may occur because of drivers are not installed properly.

  Try the following and see if it helps.

  Method 1:

  Try connecting to another USB port and check if it is detected, or try to connect to another computer.

  Method 2:

  Hardware devices do not work or are not detected in Windows: http://support.microsoft.com/mats/hardware_device_problems/en-us Note: I recommend to install the drivers for the keyboard and check if it helps.

  Method 3:

  Remove and reinstall all USB controllers.

  To remove and reinstall all USB controllers, follow these steps:

  (a) click Start, run, type sysdm.cpl in the Open box, and then click OK.

  (b) click on the Hardware tab.

  (c) click the Device Manager button.

  (d) expand Bus USB controllers.

  (e) right click on each device under the Bus USB controllers node and then click on uninstall to remove them one at a time.

  (f) restart the computer and reinstall the USB controllers.

  (g) connect the removable USB storage device and perform a test to ensure that the problem is solved.

  Keep us updated on the status of the issue.

• Error message: "iTunes is not installed correctly. Please reinstall iTunes.

  Original title: program program program App Kompatibilitet Spel Spel Aldre Krasch Kraschar upp sig sig Hanger Hanger

  I get this message: "iTunes is not installed correctly. Please reinstall iTunes.
  ' Error 7 (windows error 5) "when I try to run iTunes.
  No matter how many times I reinstall the program nets.

  Trying to download iTunes again, but instead run the installer from its current location, try saving it to your hard drive and then run the configuration file.

  Problem installing iTunes or QuickTime for Windows
  http://support.Apple.com/kb/ht1926

  iTunes for Windows Vista or Windows 7: troubleshooting...
  http://support.Apple.com/kb/ts1717

  You can try both uninstalling and reinstalling as a new user to see if that helps:
  http://Windows.Microsoft.com/en-us/Windows7/create-a-user-account

  If this isn't the case, I recommend you contact Apple for assistance.

• Creative cloud not install after that I put my user password

  Creative cloud not install after I put my user/administrators password, nothing happens after. I have creative cloud before but I deleted it instead of uninstall. I tried everything and nothing works, I have urgent need! someone please help! -Thank you

  When you install or update, it's PROBABLY your operating system for you to prove that you have by asking your COMPUTER, not your Adobe https://forums.adobe.com/thread/2139902 password password

  Sign out of your account... Uninstall... to run vacuuming...

  -non-Cloud programs, to disable the service before uninstalling

  -http://helpx.adobe.com/creative-cloud/help/install-apps.html (and uninstall)

  -using the vacuuming after uninstalling and before reinstalling is often necessary

  -https://helpx.adobe.com/creative-suite/kb/cs5-cleaner-tool-installation-problems.html

  -Restart your computer... Sign in to your account... Reinstall

  - and 5 steps in response to #1 https://forums.adobe.com/thread/2144928

• First Pro CS5.5.2 will not install after the replacement of the motherboard?

  First Pro CS5.5.2 will not install after replacing mothboard. It was running properly for 4 weeks before changing due to problems connecting AC and wireless connectivity.

  Adobe, case No. 183519673, Adobe engineers (Asia/Pacific) have worked on this issue for more than 3 hours with no result after uninstalling and reinstalling.

  Ideas for resolving the issue wou; LD appreciated.

  Also available at the section of material http://forums.adobe.com/message/4634472

  There is a new forum for download & install and installation issues

  http://forums.Adobe.com/community/download_install_setup

  Or, call Adobe

  In the United States - Adobe install problems 800-642-3623

  In the United States - Adobe Activation 866-772-3623 Open 24/7

  I offered to provide information of make and model of motherboard

  [Additional information about else added]

• HP Deskjet 1056: HP Deskjet x 64 will not install on Windows Vista

  HP Deskjet 1056 will not install on Windows Vista

  Hello

  Remove the complete software for printer. Download the latest drivers and software from link below and installation of ty.

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?cc=us&DLC=en&LC=en&product=372330&

• KB976569 will not install in Windows xp, error OX66A HELP

  KB976569 will not install in Windows xp, error OX66A HELP

  Rick

  Hello

  Follow the instructions in the link:

  Codes error '0x8007066A' or '66' was to occur when you install updates of .NET Framework

  http://support.Microsoft.com/kb/2507641/en-us

  I hope this helps.

• HP Photosmart D110 printer will not install with Windows Vista?

  HP Photosmart D110 printer will not install with Windows Vista?

  Hello

  (1) what happens when you try to install the printer?

  (2) you get an error message?

  Method 1: You can run the fixit available in the link below and check to see if that makes a difference

  Problems printing and printing errors

  http://support.Microsoft.com/mats/printing_problems/

  You might want to know

  Add or remove a printer

  Thanks and greetings

  Ajay K

  Microsoft Answers Support Engineer
  ---------------------------------------------------------------------------------------------------------
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Windows Phone, recovery tool is not installed in windows 7, says the hash value is missing

  Windows Phone, recovery tool is not installed in windows 7, says the hash value is missing. Whenever I try to install the windows phone recovery tool it does not install error

  0 x 80070003, system can't find the path or 0x800b0101, hash value is missing... Please help

  Hi Imran,

  Thanks for posting the query on Microsoft Community.

  I'm sorry to know that you can not install Windows Phone on Windows 7 recovery tool. The problem could be due to system files or software problem.

  Try to solve the problem by following the methods below.

  Method 1

  Try to run the patch from the link below and check if it helps.

  Error code 0 x 80070003 when a preference of group policy is applied on Windows 7 clients:

  http://support.Microsoft.com/kb/2904034

  If the problem persists, then go to method 2.

  Method 2

  Refer to suggestions provided by Vijay B responded on December 22, 2009.

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-system/the-system-cannot-find-the-path-specified-error/dae5f759-B053-4a4a-87af-42e79f517631

  I hope this helps to solve the issue. If the problem persists, get back to us. We will be happy to help you.