Network IDS Sensor/system and retrieval of Images

Similar Questions

• Laptop HP Envy 15 - C8P48AV: creating an image and retrieval using image-requiring a strategy

  I read a lot of posts on this site and others, and by this point, I'm a bit confused best practice procedures and processes to make an image and restoration of this image. I hope that someone will share a proven process. To return to Windows 8 HP software is still in the partition of my HARD drive.

  The recovery partition is 23 GB in size. This would imply that need a 32 GB flash - right? The flash either a card or a USB key? Use it for a recovery turn my PC for installation in original factory Windows 8.0, which is not my first choice. In addition to installing Windows 8.1, there are a ton of updates to Microsoft Windows launched. Back to Windows 8.0 would not be my first choice.

  Assuming that my version of Windows 8.1 is corrupted not what is the best way to copy an image to an external USB HDD and then read my HARD drive internal, preserving the ability to boot?

  Should I use DISM to verify that the Windows component store is intact? Are there warnings guard or mines here?

  This PC has a UEFI BIOS and USB 3.0 ports. Are there aspects here?

  Again, I am looking for a strategy.

  Thank you in advance to tackle this very basic question.

  I've never had much success with Acronis imaging software. Same software Paragon backup home & free version 12 recovery provided me with better results.

• The difference between an image of system of sfr and sfr boot image

  Hi all

  I use ASA 5525-X with fire power module. I met 2 new concepts when I upgrade the software for my module of sfr, which is the image of the system and the boot image.

  I would be grateful if someone can tell me what is the difference between sfr and sfr boot image system?.

  Thank you!

  Hello

  You will need to run the boot image on ASA, so that the SSD is responsible with the SFR image. The system image must run SFR services thereon.

  Reference: http://www.cisco.com/c/en/us/support/docs/security/asa-firepower-service...

  Kind regards

  Aastha Bhardwaj

  Rate if this is useful!

• wireless network icon has disappeared from the State system and the notification bar

  wireless network icon disappeared from the tray system and notifications (that is to say, it is no longer a wireless icon by the clock where I can see networks, connect to the network, or see the strength of the network).  How to bring back icon?

  See the following article: http://support.microsoft.com/kb/945011.  It should help to solve your problem.

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Windows 7 "the network connections folder could not retrieve the list of the network adapters on your Machine. Please make sure that the network connections service is enabled and running. »

  Get the message "the network connections folder could not retrieve the list of the network adapters on your Machine. Please make sure that the network connections service is enabled and running. "I am NOT able to connect to the internet please help. I use Windows 7 OS

  Hi Odile,

  Thanks for posting your question in the Microsoft Community forum.

  It seems that you have a problem with the connection to the Internet and receive the error message "the network connections folder could not retrieve the list of the network adapters on your Machine. Please make sure that the network connections service is active and running".

  
  I imagine the inconvenience that you are experiencing. We are here to help and guide you in the right direction.
  I may need a few more details to better understand the issue.
  1. did you of recent changes on the computer before this problem?
  2 do you have wireless or wired Internet connection?
  Method 1:
  We'll first run check network troubleshooting if this can help.
  Using the troubleshooter from network in Windows 7
  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7
  Method 2:
  If the problem persists, I suggest you try the procedure described in the article and see if it helps.
  Wireless and wired network problems
  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1
  Method 3:
  If the problem persists, I suggest you try the procedure described in the article and see if it helps.
  How can I troubleshoot network card?
  http://Windows.Microsoft.com/en-us/Windows7/how-do-I-fix-network-adapter-problems
  For more information, please see the link.
  Why can't I connect to the Internet?
  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-the-Internet
  Get back to us and let us know the State of the question, I'll be happy to help you. We, at tender Microsoft to excellence.

• How can I program a button to retrieve an image from a user base and insert them into a form field?

  I need help (I have not the slightest idea) with a java script to program a button to retrieve an image from a user base and insert into a form field. To go to the menu select icon.

  [edited by moderator - he had no body to the post office and it was while heading a long title.] [Shorten the title and pasted the original title, plenty of length as the message body]

  Okay, that's actually quite easily. As the l' evenement event MouseUp button, select "Execute JavaScript" and enter this code:

  event.target.buttonImportIcon ();

  When you click the button it will open a file selection dialog and the selected file is displayed under the icon of the button.

• retrieve and record continuous images in labview

  Hello

  I use the NI 1744 smart camera to capture and record continuous images of a moving object. My smart camera is detected in MAX and made the seizure of an image. But when I use the attached file of VI in labview, the smart camera is not detected, only the webcam is detected and a video can be generated using the webcam. Please help me detect the NI 1744 smart camera. I will be grateful.

  Hello

  Your smartcam is not directly accessible from your PC because it is a remote device.

  Create a project in real time to access your camera.

  Have a look here: http://forums.ni.com/t5/Machine-Vision/Error-1074397145/m-p/535230/page/2?view=by_date_ascending

  Concerning

• I have a xp system and I am getting the error message following, that c:\windows\system32\nimariwu.dll is not a valid windows image several times. How can I fix this problem?

  Error message for several packages of software that I installed, including Outlook and Adobe. Where can I get a copy of the correct file to copy on the wrong file I have. I have no installation disk, and need this file to be correct.

  Looks like some sort of malware infection.

  I suggest talk us a bit about your system and then run the scans indicate below, then when the scans is clean, the persistent problems.

  What is your system brand and model?

  What is your Version of XP and the Service Pack?

  Describe your current antivirus and software anti malware situation: McAfee, Symantec, Norton, Spybot, AVG, Avira!, MSE, Panda, Trend Micro, CA, Defender, ZoneAlarm, PC Tools, Comodo, etc..

  The afflicted system has a CD/DVD drive work?

  If the system works, what do you think might have changed since the last time it did not work properly?

  This will minimize back Q & A and eliminate guesswork.

  While you wait, I could do this:

  No matter what you use for protection against malware, perform the following analyses for malware, then correct any problems:

  Download, install, update and do a full scan with these malware free
  detection programs:

  Malwarebytes (MMFA): http://malwarebytes.org/
  SUPERAntiSpyware: (SAS): http://www.superantispyware.com/

  They can be uninstalled later if you wish.

  The scans by operating clean, then to solve any problems.

• Qosmio G20 and Acronis True Image

  Hello

  I have a G20 with the media library and twin 100 GB hard disks that are configured to act as two separate discs (set up of RAID options when I reinstalled the system). I have programs on a disk (C) and the operating system and my data on the other (D).

  On a previous thread I asked to retrieve the C drive only from the recovery disks without wipe data on the D drive, and it seems that this is not possible, to remedy this, I decided to follow the suggested advice and create an image of the C drive for later retrieval if necessary. However, I have had a problem of creating an image or a clone of my system using Acronis True Image disk and wonder if anyone can help. I replaced the D drive with a new disk of 120 GB and uses the old drive in a USB enclosure sata to store the clone or image recovered.

  First of all, all devices, readers ext usb, wireless keyboard, cable network & second screen are connected through a hub to a USB docking station, and when I try to clone with this joint, it fails to restart. Undeterred, I took off the hub and the clone for the external drive seems to work very well. However, when I remove the drive from the existing system and replace it with the clone to test, it does not work. The system appears to start but then get the screen where it says windows windows had a problem and I want to start in safe mode, last known working system, or start as usual in any case. If I select it just reboots and gets back to this screen.

  Also, I tried to create an image rather than a clone and recover the image on the hot spare. Once again, it seems to go ok but when I put the disc and satrt to the top of the same thing happens.

  I don't know if there is anything that you must close before imaging or cloning as the instructions don't say, so don't know if theres nothing running that may affect it. The instructions are pretty basic but seem pretty simple, so I do not see where I am going wrong.

  Does anyone have experience of this type of problem and how to fix it.

  Thank you very much

  A few months ago I acquired a regular copy of Acronis True image for my G20.

  After that many negative attempts to use the program, who do not recognize the disks
  I asked for help using Acronis
  which solves the problem brilliantly, sending me a special version on purpose
  for the difficult features of the Qosmio system.

  If you an e-mail to the Acronis media, they probably have in the Archives of the version
  for the Qosmio G20.

• Why when I backup after selection keep only last system only the old image image is maintained?

  Why when I backup after selection keep only last system only the old image image is maintained?

  Hello

  ·         What operating system is installed on the computer?

  ·         The computer is connected to the domain network?

  If you are using Windows 7 then you can try the steps mentioned below and check to see if they help.

  When you schedule a backup on your computer, all the backup files would be automatically and replaces the old backup data.

  You can follow these steps below to remove the system image backup.

  1. open the control panel (all items view).
  2. click on the backup and restore icon.
  3. as the backup, click on the link manage space.
  4. to select a backup location-
  NOTE: This is for which the backup of files the user is located in. If the backup location is already displayed, go to step 5.
  (A) under the backup location, click Browse.
  (B) go to the backup location and select it.
  (C) continue to step 5.
  5. under backup of user files, click View backups button.
  6. Select the period of backup that you want to remove, and then click Remove.

  See also:

  Learn more about the system image backup

  http://blogs.technet.com/b/filecab/archive/2009/10/31/learn-more-about-system-image-backup.aspx

  Should what backup settings I use to maximize my disk space?

  http://Windows.Microsoft.com/en-us/Windows7/what-backup-settings-should-I-use-to-maximize-my-disk-space

• Restore the system and restore point do not complete succesffully

  I have a 32 bit Vista Business operating system. I was able to get my system restore and work the restore points. I have a backup of 1 t. (Bufffalo) who works for other backups of files etc., the computer and the Buffalo blinking and seems to be something for long periods of time, but then I get an error message (unsuccessful backup) I tried other smaller disks hard backup with the same result. Can someone help me please / thank you

  Hello

  Restoration of the system and make backups are two different things.

  System Restore is to put your computer settings to an earlier date: yesterday, or last week, etc. (data are not altered during this process.)

  Backing up is backup of data or make a System Image.

  If you have problems with the system restore, this can help you:

  1. If you are using Norton, you should disable Norton inviolable Protection before using the system restore.

  http://Service1.Symantec.com/support/sharedtech.nsf/pfdocs/2005113009323013

  2. try to use Safe Mode system restore.

  http://bertk.MVPs.org/html/restoresysv.html

  3 Malware will stop at the system restore.

  Download, install, update and scan your system with the free version of Malwarebytes AntiMalware, if necessary in Mode safe mode with networking:

  http://www.Malwarebytes.org/products/malwarebytes_free

  And here's how to go in Safe Mode options; Select safe mode with networking from the list of options:

  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  This is the backup information:

  "How to back up your data.

  http://www.wintuts.com/how-to-backup-your-data

  As you have Vista business, you can make a full backup of the computer...

  «How to use complete PC and restore backup utility in Vista»

  http://www.bleepingcomputer.com/tutorials/how-to-use-Vista-complete-PC-Backup/

  See you soon.

• Y50-70: Windows cannot find a system on this computer image

  As he attempted a recovery with a copy of the provided by Lenovo recovery partition, I get: "Windows cannot find a system on this computer image.

  I have both the recovery partition of Lenovo on the HARD disk that came inside the laptop (15,56 GB, PBR_DRV) and a copy of it on an external HDD USB (started from it!). Why recovery software do not?

  Where is this "System Image"?

  Help, please.

  Thank you.

  
  

• IMAQdx multi-camera systems: shortcuts for composite image sewn

  Imagine a system using for example multiple GigE cameras through IMAQdx interface where we want to be a stitched composite of multiple camera views. The principle of sewing is naïve, simple concatenation, one next to the other.

  The problem is that, when it is trivial to build a composite image, it is difficult to do this very effectively. Image sizes are large, tens of millions of pixels, so that each copy of questions. Configurations material alternative would open many options but say we are stuck using GigE cameras and (at least initially) the IMAQdx interface. What are the tips or even hacks, you guys can imagine facing this challenge?

  I've seen some talk about the IMAQdx capture buffers and it seems to me that one can not manually allocate these buffers or access it directly. The absolute best scenario would obviously be to hack your way around to spread the image data next to each other in memory, sort of as follows in scenario1.png:

  

  The foregoing, however, don't seem to be too easy to achieve. Second scenario would be to acquire in the individual buffers and perform one copy in the composite image. See the illustration below:

  

  Interfaces usually allow this with relative ease. I have not yet tested, but based on the documentation using ring acquisition of buffer and "Extracted IMAQdx Image.vi" this should be possible. Can anyone confirm this? The copy can be carried out by an external code as well. The last scenario, without ring buffer, using ' IMAQdx to Image2.vi ' might look like this:

  

  The second copy is a loss for this scenario should be out of the question.

  I hope this makes some. Want you magicians say about this?

  Unfortunately he has no concept of a "sub-image" where you could have acquired acquire seamlessly in an image that represents a region of a larger image. However, you are right that the acquisition of the ring with the extract is the way to remove a copy. In this mode, the user allocates the internal buffers imaqdx uses by means of standard images, and then they can access those without copying directly. You can simply extract the image of each camera (zero-copy) ring buffer, then use the VI ImageToImage to copy a region in your larger picture (a copy).

  Eric

• PCI-6025E (DAQ) and cards-1409 (Image Interface) PCI

  Hi friends,

  I have PCI-6025E (DAQ) and cards-1409 (Image Interface) PCI installed on the Windows XP desktop, that connected to the deducted Mikron camera.

  Recently I spend my Labview to 8.6, but the Mikron camera installation software does not work.

  How can I solve the problem?

  Anyone have the installation software (PCI-6025E (DAQ) and cards-1409 (Image Interface) PCI)?

  Any suggestion is appreciated.

  Thank you

  Jack

  jackp6,

  For the 6205E you will need to download an install the Drivers OR-DAQmx which you can find here:

  NOR-DAQmx

  http://Joule.NI.com/nidu/CDs/view/p/ID/2214/lang/en

  The 1409, you must NEITHER IMAQ drivers that are included in the following the Acquisition of vision available here:

  NEITHER Vision Acquisition Software 2,010.08

  http://Joule.NI.com/nidu/CDs/view/p/ID/2137/lang/en

  Please let us know if you have any other questions.

  Kind regards

  Sam K

  Technical sales engineer

  National systems

• Window xp sp2 professnal operating system and drivers for compaq 420

  Hi comrades.

  I buy a new computer compaq 420 laptop. I have installed window xp professional sp2. after complete installation, the drivers are needed for the healthy material. I go to my computer then select Properties Device Manager and see the following drivers required

  1. hp integrated module

  2. network controller

  3. PCI device

  4. video controller

  5. video controller (VGA compatible)

  Then I click on the hp site enter the product number select the operating system and download the drivers and install it.

  I explain all the above procedure, a situation of problem or interbreeding because of swear I've met who, in virtue.

  I have install the driver of HP integrated module, video network controller and also .netframework 3.0 Microsoft.

  Now there is no sound / audio so I install the audio drivers sound is the device driver PCI is ok after installing the audio driver but HIGH DEFINATION AUDIO BUS DRIVER SHOWN in the DEVICE MANAGER I ALSO DOWNLOAD IT of THE SITE HP

  BUT ALWAYS YELLOW ICON IN THE DEVICE MANAGER. SOME OF MY FRIENDS SUGGEST ME THAT DOWNLOAD THE UAA BUS DRIVER 1.0 OF MICROSOFT, I DID INSTALL THEM, BUT THE PROBLEM STILL THERE.

  How to SOLVE THE PROBLEM?

  The other problem is that HDA bus once is ok, but the PCI bus becomes yellow. I have search everywhere on the web but not found.

  I explain every thing here please help me.

  Thanks and greetings

  Hello

  First download and install:

  Intel Chipset driver ici

  and don't forget to restart your system when you do.

  To get to his card work download and install first:

  MS-UAA for XP with SP2 (required with a reboot before the graphics and Audio, Modem driver) here

  Only after this, download and install:

  IDT Audio high definition (HD) Driver here

  Now install the driver for graphics card:

  Driver video Intel and control panel here

  Peripheral PCI should be modem:

  LSI High-Definition Audio (HDA) Modem Driver here

  HP integrated module (which is for sure Bluetooth) and network controller have few opportunities on your list of model drivers, so we will need more information to give you an answer corerect to solve these two problems. Reach:

  Control Panel-> system-> hardware-> Device Manager

  Click with the right button of your mouse on each yellow sign with exclamation point ( ), and then choose Properties. Then, go to the ' Details ' tab and paste hardware ID here. This way we will know what it is.

  Below, an example of how you do it: