New hard drives Dell Poweredge 2950

Similar Questions

• New hard drive Dell PE 1900

  Just ordered 2 new hard drives of 300 GB of Dell $ 300 each.  Have Perc 5 / i Raid 5 config.  I was told that I could get 2 hard drives from WD a lot cheaper at microcenter who would work as well?  If I want with the Dells that are in transit?  Thank you

  Depends on the model of WD drive. Nevere use desktop/laptop (green, blue) readers and do not use the NAS (red) drives. Only certain versions of readers RE are provided by WD to work on Dell DCs. So, if it's not a disc RE WD States are working on PERC controllers, and then use the readers of Dell. Also, for future use, don't order disks directly from Dell. Buy the same readers certified suppliers. For example:

  http://www.xByte.com/ProductDesc.aspx?code=CAT_1261_9

  http://www.Amazon.com/GP/product/B005CIO1GO/

• Reinstalling Vista on a new hard drive in a Dell XPS420

  I have been using my Dell XPS 420 for years, but lately the C: drive (with Windows Vista Home Premium and the recovery partition) are dead. I had to reinstall Vista on a new hard drive. It went well until Vista was finished all the updates that are accumulated. He says that my Windows is not genuine, and he refused to go further than the connection. The Windows CD is Dell and it came with the computer. My Dell warranty expired a long time ago. Can anyone help?

  Using the recovery process of the manufacturer normally does not require activation. It will activate itself during the recovery process.

  Product key and product ID are two different things

  Read this about AV Avast which causing 0xC004D401 error Code

  http://social.Microsoft.com/forums/en-us/genuinevista/thread/a3145e58-EAEA-43e5-B2DB-c15885076c48

  And read this topic to report diagnosis by Christmas Paton.

  http://social.Microsoft.com/forums/is/genuinevista/thread/a3fda1a0-6199-41a4-b3d6-5be62cae3d79

  And if necessary, repost in the Vista install, upgrade, and activate forum (this one).

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-windows_install?page=1&tab=all

  Noel Paton, he will come here.

  This is the right forum, but it may not read fine on the information contained in the header not mentioning not activation problems

  See you soon.

• Dell Inspiron 3520 - hard drive failure - how to install Windows 8 on the new hard drive

  I bought Dell Inspiron 3520. My hard drive has stopped working completely. It was stated as dead hard drive by diagonstic center.

  I have now bought a new hard drive but have lost data and windows 8 preload on the original hard drive. Dell did not provide any recovery disk for Windows 8 pre-loaded on portable hard drive. How can I then install windows 8 / 10 on my new hard drive?

  The .iso image file official 10565 has only:

  • Overview of the House of insiders
  • Overview of the Insider Pro

  Unfortunately, there are 5 editions of Windows 10 and so 3 are missing. If your key is not automatically entered and accepted, it's probably a simple language edition or edition N.

  When Microsoft release 10586 - TH2 - 1511 Version they will probably have an .iso that contains all 5 editions in 1 .iso or alternatively 5 .isos distinct (I hope as the first case that it will make Windows installation much easier).

• Dell N5050 - new hard drive, no WiFi

  Just installed a new hard drive in a N5050 Dell laptop. I have no WiFi signal and the antenna is running. I guess that I have not installed a driver or something. I have the CD Driver provided with the laptop originally. There are only 2 choices for drivers. On East Realtek RTL81XX PCI - E card WLAN - I installed but it seems that this is not a wireless driver. It keeps saying that I have a loose cable. The other on the CD is 1525 Wireless Atheros WLAN Mini Card computers desktop, but when I try to install this one I get an error of installation DW: Setup cannot run on this platform. Please select package for your operating system. Should which driver I?

  Hi all, hey just a note to say I've set. Since she had no internet signal I have download the drivers on a memory stick and then try to install on the laptop, but I kept getting errors in digital signature. What I ended up doing was restarted the laptop and press F8 to keep me my Start menu. Once there, I disabled the verification of signature. Rebooted and then the pilot had worked. Once I had a driver to work, I was able to connect to Dell, enter the number of my service and it looked all good drivers I need and install. After this, I restarted and press F8 and reactive the verification of digital signatures. It now works like a charm. Might have been a long journey around him, but I'm back in business. Thanks for all the ideas, they have certainly helped.

• I installed a new hard drive for my dell Inspiron 1525 and try to install windows 7. He asks me to install the driver. How to do it

  I installed a new hard drive for my dell Inspiron 1525 and try to install windows 7. He asks me to install the driver. How to do it

  Using the Dell recovery disks to reinstall?

  The origonal drive failed?

  If you are using a real MS win dvd during the first part of the installation it can not find a drive or ask a driver, then the driver is obtained from Dell, specific to your model, its likely the driver sata, you need to download to say a USB and then point to this file when the installation application the third-party driver.

• Dell Inspiron 8200 + new HARD drive

  I bought a new hard drive for my Dell Inspiron 8200. But when I tried to install it I was faced with a problem. It seems that Seagate IDE 80 GB at 5400 RPM to the manufacturer S 9 1038-508 does not work with my laptop even if the sellers at the store assured me that it would work. As far I can see what the proplem that the pins on the HARD drive is not taking the laptop and the HARD drive box blocks 4 pins on the hard drive. But frankly say, I am surprised because the hard drive installed perfectly in 2 other laptops. He was spending money for nothing, or am I wrong?

  
  

• DISK BY DELL POWEREDGE 2950

  Buongiorno, TR e rotto UN drive hard nel Server Poweredge 2950. E' UN DELL BARRACUDA ES.2 manufactured by da SEAGATE 1000 GB con S/N 9QJ34S01 and P/N 9EF248-050 (Serial Attached SCSI - SAS).

  He disco fa parte di una configurazione RAID 1, che I like ripristinare al più presto.

  I like acquistarne uno ed avere un preventivo. I'm dati by engineering del preventivo e spedizione sono:

  A.m.. Architetti S.r.l.

  Viale Bruno Buozzi, 49

  00197 ROMA

  P.IVA e C.F. 04869451007

  VI prego di farmi turned out he con preventivo di price terms prima possibile.

  Grazie

  Speaking saluti

  Michele Angeletti

  Buongiorno,

  Con passing it mouse sopra identifier c Supporto Dell'e the voce "private message", it could mandarmi come message privato di seguito required information?

  - Service tag del Server

  -ed email phone number

  Speaking saluti

  Manual

• Dell PowerEdge 2950 P2V problem

  Physical server:

  Dell PowerEdge 2950

  Windows 2003 R2 Standard x 86 operating system

  Sheet music:

  Dell - hidden partition

  C: BONE

  D: Data1

  E: Data2

  F: Data3

  G: data4

  vSphere ESXi 4.1 (under license)

  ISCSI SAN

  vCenter Server

  I tried on cold hidden server with boot CD, but received the error "unable to determine the operating system invited."  Looks like that I don't have the driver for the Dell raid controller in the boot CD.

  I decided to go with the hot P2V using the plug-in for VirtualCenter.  I stop the SQL server service and disabled the firewall disabled the anti-virus tools.  Only two partitions (C and G) on the physical server must be in the new virtual machine.  So, I've selected partitions C and G and has increased the size of the drive at a time.  I made sure not to install the vmware tools and unchecked the option reconfigures.   The P2V conversion was successful.   But when I went to start the virtual machine, it starts with the 'VMWARE' logo and restarts immediately.  Restart the virtual computer so fast I can't even in the BIOS unless I hit the key several times.   I did the clonning with the hidden partition, but with the same problem.   There are no BSOD or any indication that the virtual machine cannot find the vdisks.   Called in vmware support.  They used webex for an hour, but could not fix.  Asked me to send in the logbundle.

  I HERE it if someone tell me what I am doing wrong?

  Thank you

  Another option is to install the Standalone Converter 3.0.3 on the PowerEdge, stop all services and performing the conversion.

  André

• SMU 8108 does not start with the new hard drive

  Hello

  I am currently using SMU 8108 with SMU-1062 q.

  The previous record was borken, so I had to install a new hard drive.

  The new hard drive is fommatted as NTFS format, and it is currently mounted on 8108.

  Unfortunately, I don't have recovery disk available to the general public so I am trying to install Windows 7 on a blank hard drive.

  When you start, the LED OK PWK light is all the time, orange DRIVE LED turns on for a few seconds only when I turn on the switch.

  LabVIEW RT switches are all off, I cleared CMOS several times to the Board of Directors, but the screen does not show anything.

  I tried to use my DVI monitor with any other device as well, and it worked, so there is no problem with the monitor.

  In addition, I tried to go in window safe mode by pressing F8 or Del it didn't work, so I can't see anything on the screen when his kick upward.

  I tried to put a lot of information I can it will be very appreciated if you can help me with this problem please.

  You said that you can't in Windows safe mode, you have installed Windows on the hard drive?  Are you able to get into the BIOS of the controller?

  If you are not able to access the BIOS for the controller, it may be due to bad RAM.  If you are uncomfortable installing RAM and you have a few extra laptop RAM of the same type (I think it's the DDR3 for your controller) laying around, you can try to replace the RAM.

  Was your hard drive damaged through certain events, or it just stop working?

• Windows Update does not work after new hard drive

  After you install the new hard drive, when I click on windows update, it opens, makes his scan, then I get the message, (the website has encountered a problem and cannot display the page) I have a Dell Optiplex 745 running XP Pro, Explorer 8, have tried several times and restarted, please help.

  What do you think of will be without safety last cumulative update for IE8 be manually downloaded and installed before going to windows update to nothing at all.  What will happen is the CPU at 100% and a whole lot of nothing else of fortification.

  Do not go in line with the hopes of getting the updates of windows after the installation of SP3.

  Disable automatic updates in Control Panel > automatc updates > disable automatic updates

  Start > run > wuaucpl.cpl > disable automatic updates > apply (if the setting is changed) > OK

  Get the exe to install offline full download for IE8 [should represent approximately a 16 MB file] and then install IE8 after SP3 and the decline of the ability to download updates for IE8 at installation time.

  Then manually download and install the current cumulative security for IE8 update and restart the computer.

  visit Windows Update through your browser link in the start menu.  Consent to any ActiveX install queries and validation / advantage genuine offer and cross your fingers.

  It is possible that you may still have questions, but this will reduce some of the problems if you follow the recommended sequence.

• Can't reinstall XP service pack 3 on the new hard drive, will not cross of EULA

  Computer VOstro 220 (Dell) under the age of 18 months. Internal HD died and was replaced two weeks ago with a HD internal 320, the speed of 7200 Western Digital. (Micro Center, a computer store large installed the HD that I bought at the store)

  I used the OEM "reinstall Windows XP service Pack 3" DVD.  With F12 I put the computer to boot from the DVD.

  DVD boots, I chose the option to install the OS

  Fisrt I see the message that the program checks the material. No error message

  Then I see the screen with the words "Windows Setup". Five minutes later, Microsoft EULA (end-user contract) is displayed.  IT does not scroll, I used the arrow keys on the keyboard to get at the end of the EULA was waiting for some kind of "type option"I agree". But there is nothing.

  Nothing more happens. No additional configuration.

  What is the problem? What should I do to get the Windows XP installation to continue?

  Why not install the operating system?

  Anywhere between 5 and 20% (depending on the production) new hard disks are defective. Test your drive with the factory utility.

  Hard drive test - CD Bootable:
  If you have a new hard drive Seagate the very next thing would be to download Seagate Seatools (bootable CD)
  and check bad sectors:
  http://www.Seagate.com/WW/v/index.jsp?locale=en-us&name=SeaTools&vgnextoid=720bd20cacdec010VgnVCM100000dd04090aRCRD

  For Western Digital readers to download the .iso from WdDiag file: http://support.wdc.com/product/download.asp?groupid=611&sid=30&lang=en

  Samsung Estool: http://www.samsung.com/global/business/hdd/support/utilities/ES_Tool.html
  Samsung Disk Manager software: http://www.samsung.com/Products/HardDiskDrive/utilities/shdiag.htm
  Hitachi Drive Fitness Test Software: http://www.hgst.com/hdd/support/download.htm#DFT
  Diagnostic tool available for use by customers who feel their Toshiba brand Fujitsu hard drive:
  http://SDD.Toshiba.com/main.aspx?path=ServicesandSupport/WarrantySupport/SoftwareUtilities
  Notice of suport Fujitsu disk utility: http://www.fujitsu.com/us/services/computing/storage/hdd/
  Toshiba CD bootable: (BACK Diagnostic Tool version 7.0 for IDE/ATA/SATA hard disks)
  http://SDD.Toshiba.com/main.aspx?path=ServicesSupport/FujitsuDrivesUSandCanada/SoftwareUtilities#diagnostic

  JS
  http://www.PAGESTART.com

  Never be afraid to ask. This forum has some of the best people in the world to help.

• where are my drivers? new installation on the new hard drive

  I have a dimension e510, I put in a new hard drive. I got the windows xp disk, I added when I bought the computer. In general, the hard drive is partitioned or something with the operating system on the hard disk of windows xp.

  In any case after I installed widows xp, everything works except that I have the yellow question mark by 'other devices', I noticed that when I tried this computer with my main computer of the network. All of the devices under the heading other have no driver video Ethernet, PCi, for example - video works as I have a video card.

  So I tried to install the drivers and windows is unable to find them. I still have the installation disc into the computer. Being one of the drivers for the Ethernet - i cannot access the internet to get drivers. Help

  OK, I found the drivers on the dell site. I was able to install or update several drivers that I didn't need. the pilot opne I need comes in a cab file inpenuxp.cab.  Where do I put this? I've tried several things that work. When I low laoded the other driver of dell updtates, they all seemed different and they are all installed without problem

  Hello

  You will need to download "Intel PRO/100 VE Network Connection " of Dell on a USB key and install the driver for your Netbook have access to the internet.

  A CAB file is a ZIP , CAB file is just the Microsoft format for a compressed folder save bandwidth on their server they save as aCAB , you can open and then select all and extract here where the files need. For the most part, these files will file dell cascading, images and Html pages.

  Try to download the network card in your computer to get the correct driver installed for your problem.

  NASS - http://www.nasstec.co.uk

• New hard drive, installed Windows XP PRO version 2002 - resolution screen and internet problems

  My Dell has had some problems (patially due to age), so a buddy of mine and I put a new hard drive in it and then installed windows XP Pro.  Installation went great, but now that it's installed, I can not get the screen resoultion to change and I can't connect to the internet.  I feel like with the internet, can I have a driver problem.  I know that the internet works, I'm on it with the laptop right now.  Any suggestions?

  ????  I'm not sure I understand your question. You download the drivers to a place, you will find them, as the office. If you want to put them on a USB stick, copy the files downloaded to the key and take it to the computer target. Copy the files on the computer desktop. Double-click on a file and it will unpack the installation routine starts. Follow the installation wizard. Reset when said to repeat as needed until all the drivers, etc are installed. Subsequently, you can delete the downloaded files from Dell (from installation .exe). MS - MVP - Elephant Boy computers - don't panic!

• The new hard drive will interfere with user passwords?

  I replaced my hard drive on my Dell Inspiron (Windows Vista Home Basics).  The new drive will interfere with my user passwords?

  Mona

  Hello

  You do not say what user passwords you talk, after replacing the hard drive which will be then require you to reinstall the operating system

  If you refer to the online user passwords (Facebook, Twitter, etc.), they will remain the same.

  If you are referring to your Vista account permissions to access, with a new hard drive and you reinstall the operating system, you will need to put in place all the user accounts and passwords user again for them.

  See you soon.