New volume detected at / 2016-02-20 19:21:18-0500 corrupted file: /private/var/folders/zz/zyxvpxvq6csfxvn_n00000s0000068/C/com.apple.SoftwareUpda you / CFNetworkDownload_baIZJT.tmp

Similar Questions

• Console of r. used to fix the MBR, now dirve says "New Volume"

  OK, I'm having a big problem.

  I'll start by saying that my computer a few days ago has only been running a configuration to multibooting with linux on a disk and Windows XP on another. Linux using Grub to boot. Now, I recently updated my BIOS and this had caused a problem with GRUB not start XP properly. I decided to remove the Linux disk, simply launch XP as my main drive and physically switch the two when I need to use one or the other.

  Given that I was removing Linux, I had to fix the MBR for Windows would be to start properly. I read online that all I had to do was start using my XP installation disk in the recovery console and doing a FIXMBR and FIXBOOT. I did it, but something went wrong and he said that I had to do a CHKDSK first. So I made "CHKDSK/r" and let stand overnight (this disc is 1. 5 t so it took a while).  So the next day after work I went back to finish the FIXMBR and FIXBOOT. He gave me the same message. Now I know exactly what I did after that, if I tried other commands or what, but I finally decided to just hang up and see what was going on.

  In Linux, I see that the name of volume for my XP disc went from "XP 1. 5 t"to"new Volume ". Not good. Now I see there are two files listed: RECYCLER and System Volume Information. I guess that the disk has been reformatted somehow? Now I'm at the point where I use my XP Backup to another drive of four months ago. I did some research on the recovery partition, file recovery, etc. I came across a program (trial version) that finds deleted files. I installed and run for a few minutes. OK, good news, is that I do not see some of my files and folders, so I guess that the disk was not completely formatted/overwritten.

  I don't know how the player got there where she is now. Maybe I used a bad command or a switch?

  So my question is where to go from here? Should I get a new drive and recover the files on the new disk? Can I restore files and recover the old partition?

  I hope I didn't confuse you too much. I appreciate any help you can give.

  -Jimmy

  Hey Jimmy,

  I personally never heard a user successfully remove the GRUB bootloader without a reinstall of Windows. You have no real solution is to reinstall Windows from the Windows partition is completely empty. I don't know any Linux file recovery tools, you may need to post in a Linux forum for Linux file recovery tools.

  Sorry I don't have a better solution for you!

  Cody C
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• LV 2016: LabVIEW could not create the required channel file permission error endpoint; NOR-488: Error of hardware detected DMA

  I just installed the new 2016 LabVIEW with the two patches and wanted to check the new feature.

  When you create a channel writer, there was a pop up select the Channel end point, but whatever the option chosen, there is a window saying "LabVIEW could not create the required channel endpoint", error ccode: 8 file authorization error

  NOR-488: Error detected DMA hardware.

  I have error permition from file to file, file that is?

  By chance, do you have re-defined the default data directory in LabVIEW?  LabVIEW uses to host files for the warp threads, and if you moved from its default position in your profile (C:\Users\\Documents\LabVIEW data), especially if you moved it to the root of C:, it could become unalterable.  This must remain in your profile!

  Bob Schor

• When I try to create a new volume on my hard drive I get access denied

  I have Vista Home Premium update to the standards in force. I have problems reading windows XP files and compact optical discs. A solution, which I got from Microsoft was to partition the C drive and the new volume in Windows XP and run the software it. I followed the instructions of management of disk, but when I do the search for space fell, it tells me access is denied. Even though I know I have more than half of my drive C is empty.

  Hi doqmarr,

  ·         How did you create free space on the hard drive (hdd)?

  I suggest you to take possession of the volume, and check if it works very well. Follow these steps:

  1. click on the drive and then click Properties.

  2. click on the Security tab.

  3. under group or user names, click your name to see the permissions you have.

  Reference: http://windows.microsoft.com/en-US/windows-vista/What-are-permissions

• How can I prevent the shutdown task scheduler engine, get the new display detected to work and avoid receiving the message "Internet Explorer has encountered a problem and stop"? __

  My laptop is a Dell Inspiron 1520, running Windows Vista Home Edition Premium and Internet Explorer 9.  My extra monitor is a Sharp Aquos LED HD - TV, the model LC-46LE700UN.  I've been using a VGA cable to me onnecter the laptop and TV.

  The laptop seems to operate normally when not connect to the TV.

  As soon as the VGA cable is connected to the laptop (without being connected to the TV), the following message appears:

  'Microsoft Windows - Task Scheduler engine has stopped working.  A problem caused the blocking of the program works correctly.  Windows will close the program and notify you if a solution is found. »

  When initially, I connected the laptop to TV, "new display detected" was automatically acti EV.  Soon, it was activated is no longer automatically.  I was able to activate manually using Windows Mobility Center during automatic activation failed initially but now Windows Mobility Center no longer detects the new view.

  Using Fn + F8, I can view the image on the laptop or TV, but not both simultaneously.

  The message "Internet Explorer has encountered a problem and stop" appears intermittently, but I can still make internet sites and show the content after the message.

  I have download software, myp2p.eu, a site for watching TV programs "streaming", including PPStream, Sopcast, Live, Stream Torrent Sina, a Swarm, TVAnts, UUSee, VGO and Veetle player and canceled downloads for PPL (who failed an integrity check), PPMate (corrupted) and (blocked) TVKoo.

  Norton Security quarantined the installer of UUSee, indicating that it was a high risk of program with many users.

  To a computer repair shop and using a different additional display flat screen, I could not duplicate the problems yesterday (4 October 2010), when the "new detected display" has been activated automatically, and I could see the photo or the other and both screens.

  I tried to restore the system to a date (on the list) before when the problems occurred first - failure of the restoration of the system.  I tried to use scandisk, but received no indication that he had performed and corrected all errors found after restarting Windows.  I looked at responses from forum, the display setting and the new display detected support literature.

  How can I avoid these problems?  Help!

  Hello

  Restoring the system end up with any error message?

  This could also happen if one of the substantive programmes is in conflict with the proper functioning of your computer. To troubleshoot error messages and other issues,
  You can start Windows Vista by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  Steps-
  1 log on to the computer using an account with administrator rights
  2. click on start, type msconfig.exe in the start search box and press ENTER to start the System Configuration utility.
  If you are prompted for an administrator password or for confirmation, type your password, or click on continue
  3. on the general tab, click Selective startup, and then clear the check box load startup items. (The check box use the file Boot is not available.)
  4. on the Services tab, click to select the skin all the Microsoft services check box, and then click Disable all

  Note: Following this step lets services Microsoft continue to run. These services include networking, Plug-and-Play, record of events, error reporting, and other services.
  If you disable these services, you can permanently delete all restore points. Do not do this if you want to use with existing restore points system restore utility

  See this article-
  http://support.Microsoft.com/kb/929135

  This should solve your problem.

  -Robert

• Vista has created new volume on HD during the update. Need to delete.

  I use Vista Ultimate. During an update, Vista has failed. As part of the recovery process, he created a new volume on my hard - J drive:-where he put all my old files. He then created a brand new facility on c: I have no idea why.

  He spent 75% of my hard drive to the backup volume J space.

  Now, I've got all the files I need recovery j: and I want to reallocate space on c: and get rid of j: entirely. I shrunk J: but Vista will not let me extend c:

  I did not have enough room on j: to run Vista Ultimate, so I really need to reclaim space. Could someone please help? Thank you in advance.

  Hi NancyDL,

  What happens when you try to extend the volume?

  To create a partition or volume (the two terms are often used interchangeably) on a drive hard, there must be unallocated space on the hard drive (empty) or a free space in an extended hard disk partition.

  If there is no unallocated space, you can create some by reducing an existing partition or removing a partition.

  I would suggest you remove j: drive to make it also allocated and then extend the c: volume.

  For more information, please see the link below.
  Create and format a hard disk partition
  http://Windows.Microsoft.com/fr-FR/Windows-Vista/create-and-format-a-hard-disk-partition

  Please post back and let us know if it helped to solve your problem.

  Kind regards
  KarthiK TP

• PE R630, new battery detected.

  the server has sent the following message is displayed.

  Severity: Information, category: storage, MessageID: CTL1, Message: event log: event log: 1 new battery detected integrated RAID controller

  We didn't change any material, it suggests damaged battery?

  Thank you.

  Hello

  Shalom.a

  We didn't change any material, it suggests damaged battery?

  No, I suspect not any issue based on this information message. If the message appears frequently then I would say check log controller for battery charge values.

  Thank you

• HP MSA2324i, new volume / LUN added, cannot be seen by the host ESX 4.1 (fine old LUN work)

  Hello

  I have a vSphere Essentials Plus 4.1 cluster that is connected to 2 x bays HP MSA2324i SAN, we have 2 x hosts and both can see current volumes / LUNS absolutely perfect (vMotion and migration of VM offline all work as expected). I'm starting a consolidation project virtual disks / volume of the San 2 x, however a new volume I created on a network SAN cannot be seen by the other host.

  The new volume has been implemented exactly like the others, but of course with a unique logic for mapping unit number explicit, but when scanning the iSCSI HBA the new LUN is never found :-(

  I was wondering if others have had also this happens to them and know why this may be implemented?.

  (This is a company that I joined, it's my third week, and that they had also no VMware subscription on their reunification since 2012, otherwise I would be to connect a call to technical support of VMware, by train to get the sub upwards and running)

  OK I think that might be the cause, I came across this recently maximum LUN ID is 255, change the logic unit to a number smaller than 255 ID number and try again, let us know how you go!

  vM

  -----------------------

  VCAP-DCD / VCAP-DCA / VCP-CLOUD / VCP - DT / VCP5 / VCP4

  -----------------------

  vMustard.com

• 3D: deleting a mesh, apply multiple materials, "new volume from layers.

  I learn Photoshop CS5 Extended 3D features and have a few questions which do not appear to be covered in the reference of help documentation:

  Can I remove a mesh of a 3D layer / scene?

  For example, after the merger of the 3D layers together.

  Can I register several subjects to a single mesh?

  I see that more complex meshes have several materials applied to them. Photoshop has the ability to add or remove several materials to mesh?

  What is "New volume from layer" intended to do?

  I couldn't find this specific menu in the help reference material anywhere item.

  Thank you

  B.

  PS: I sat waiting on hold for technical support Adobe for 2 hours and 17 minutes with no sign of life before giving up. When I explored the options of online reminder, the site says that no option is available for Photoshop. This level or the lack of support is mind bogglingly awful for a company like Adobe. I know I complain about it here won't change anything, but I need to get my frustration out of my system and write helps.

  Hi b.,.

  Can I remove a mesh of a 3D layer / scene?

  For example, after the merger of the 3D layers together.

  You can only hide the mesh on the stage, not remove or delete. You must remove the entire 3D layer to remove the stitches of a document.

  Can I register several subjects to a single mesh?

  I see that more complex meshes have several materials applied to them. Photoshop has the ability to add or remove several materials to mesh.

  With Photoshop, you cannot replace a unique material with several subjects. There is very little possibility of editing of UV mapping, and you'll want to do in a 3D modeling application. Regrowth of the meshes are created with 5 materials of a single mesh so, technically, Yes to your question. But this isn't really what I think you're asking.

  What is "New volume from layer" intended to do?

  I couldn't find this specific menu in the help reference material anywhere item.

  This has applications in scientific and medical imaging, but should not be used. An example would be to use a DICOM format, several slices of Imaging scanner and have layers of scanning modeled in a volume. It's really just take successive layers and placing them at an equal distance in space. The render settings dialog box offers you a few options to vary the volume displayed after its creation.

  I'll see if I can get this model tomorrow and try to figure out why the menu items do not work. You mean the Group 4 which includes 'Hide nearest Surface', right?

  Kind regards

  Steve

• Sophos: Problems detected

  Hi guys,.

  I recently conducted a scan of my MacBook Air using Sophos anti-virus and the underside of problems have been identified:

  New volume detected to.

  2016-01-03 18:23:39 + 0000 file corrupt: /private/var/folders/f7/pmtj4c3d2bgdr714z5xhmz7m0000gn/C/com.apple.appstore/101 8109117/ftk3252456602304584541.pkg

  2016-01-03 18:23:48 + 0000 corrupted file: /private/var/folders/zz/zyxvpxvq6csfxvn_n00000s0000068/C/com.apple.SoftwareUpda you / CFNetworkDownload_qJXc74.tmp

  Please can someone advise me if these questions are harmful or not, and how to remove them from my camera.

  Thank you

  Dan

  Dan78910 wrote:

  Hi guys,.

  I recently conducted a scan of my MacBook Air using Sophos anti-virus and the questions below have been identified

  Sophos is the problem. Uninstall the application.

• HP Envy 14-1200 Prod # XQ103AV: "we could not create a new partition or locate an existing one. See the Setup log file.

  System - HP Envy14 - 1200 Beats Edition Notebook PC Series - product # XQ103AV.  It came pre-installed Windows 7.

  Error message "we could not create a new partition or locate an existing one.  See the Setup log file.

  appears in the new installation of Windows 8.0.

  Installation of MS Windows 8 DVD detects the hard drive OK.

  Software mini of Partition of the tool (3rd part) detects the hard drive OK.

  Windows 8 DVD software both MiniTool detects the disk partition and its OK formatted, but the error message is displayed to prevent installation.

  Here are the steps that I tried to solve the problem, but it won't work.

  1 opportunity Microsoft Windows 8 DVD diskpart to clean HD, to partition and to format... always get the same error message.

  2 opportunity Microsoft Windows 8 DVD diskpart to clean HD and partition... always get the same error message.

  3 MiniTool Partition software used to clean the HD, partition and format... always get the same error message.

  4 MiniTool Partition software used to clean HD and partition... always get the same error message.

  5 has bought a new hard drive repeat steps 1 to 4 and I got the... its error message.

  Background

  I have upgraded to Windows 8 Windows 7 and it worked for 2 months, then I upgraded to Windows 8.1.

  After that the system is being updated and restarted, the screen turn black.  So I decided to re - install Windows 8.0.

  There is no SIM card in the laptop.

  Help, please...

  I managed to do work Ok. Use Windows 8 DVD to run Diskpart

  1 delete the partition.

  2. restart the system.

  3. allow Windows 8 DVD to perform the partition and format the HD.

• I found this in my log files 26 July 2016, 22:55:18 com.apple.xpc.launchd [1]: the appellant attempted to divert the service: path = System/Library/LaunchAgents/com.apple.pluginkit.pkd.plist, calling = loginwindow.6205 what that means?

  I found this in my log files 26 July 2016, 22:55:18 com.apple.xpc.launchd [1]: the appellant attempted to divert the service: path = System/Library/LaunchAgents/com.apple.pluginkit.pkd.plist, calling = loginwindow.6205 what that means?

  Just a log message system that does not mean nothing, except an engineer. If you don't know what mean the entries in log file, and then save your time and forget about unless you have serious problems.

• Xcode opens with 'ICloudSetupView.strings' at startup after a full stop. Xcode is disabled as a startup item, but there is a new startup item called "ICloudSetupView.strings" that has a "sort" of "Strings File". Is this a virus or spyware?

  MacBook Pro	(15-inch, mid 2010)
  OPERATING SYSTEM	OS X El Capitan (Version 10.11.2)
  Processor	Intel Core i7 2.66 GHz
  Memory	8 GB 1067 MHz DDR3
  Startup disk	Macintosh HD
  Graphics	Intel HD Graphics 288 MB

  The past several times I completely stopped my MacBook Pro and booted back up Xcode is the first thing to open, and it opens a window, I've never seen before called 'ICloudSetupView.strings '.

  I went to check if Xcode is checked as a startup item (I usually put off because I do not often use XCode) and Xcode is not even on my list of items that opens automatically when I boot.

  HOWEVER, there is a new startup item called "ICloudSetupView.strings" that has a "sort" of "Strings File".

  I traced the file in its location and found several others with the timestamp date same creation and now I'm worried.

  The path to the file is:

  System/Library/PrivateFrameworks/FinderKit.Framework/versions/A/Resources/SK. LP roj/ICloudSetupView.strings

  
  

  The file has only the following 2 lines of code (technically 1 with overflow) that you can see in the image:

  bplist00 "_uHD " Driveo-7F-8GX.title_H4f-Te-Tzu.title\iCloud

  3 @

  
  

  A screenshot of the Xcode file that opens and my preferences of start programme is attached.

  I'm quite worried about it, especially because it IS NOT defined as part of open automatically but it is.

  I searched online and found no something like this.

  Anyone know what it is?

  Or what the code does?

  Is this a virus or spyware?

  

  It is not spyware. Simply remove it from your login items.

• The vi below opens a new data file every time new data of the visa arrived. I only want a single file of data for registration period!

  The vi below opens a new data file every time new data of the visa arrived. I only want a single file of data for registration period!

  Can someone bring me (Labview is new to me) in the right direction?

  John

  See attached the amendment. I made a change to my suggestions and possess the top-level VI for the null refnum. See if it makes sense.

• When Outlook Express 6 detects emails from a name in the right column indicates the folder in which it is in. How can you tell which folder this folder is located in?

  Column of Outlook Express folder in find

  When Outlook Express 6 detects emails from a name in the right column indicates the folder in which it is in. How can you tell which folder this folder is located in?

  OE does not have the capacity to tell you where the folder is located in the folder hierarchy.  You can select different trees under local folders to find what subfolder is and what kind of tree it is under.  Unless folders.dbx is corrupted (which happens a bit), then OE will not create folders for you.  If folders.dbx is corrupt or not, I would suggest that you backup the files and the registry (see www.oehelp.com/OETips.aspx#6) before things become corrupt, because you seem to have a complex organization from your e-mail folders.

  Steve