no access to Time Capsule

Similar Questions

• How can I configure Time Capsule 3 to and Motorola NVG589 to access the Time Capsule backup drive?

  I have ATT Uverse service and am ok with the performance of the WiFi of the NVG589. I want to configure my Time Capsule 3 to extend the network and be able to access the drive for backups Time Machine. I think I am following the steps in Airport utility, but once installation is complete I can find is no longer the time Capsule.

  I want to configure my Time Capsule 3 to extend the network

  The time Capsule cannot "extend" the network Uverse using a wireless connection, if that's maybe what you're trying to do. The time Capsule can only wireless "extend" the signal of another router from Apple.

  The Capsule can be configured to extend the network to Uverse if it is connected permanently... anytime... to the Uverse router using a connection through wired Ethernet cable.

  Please specify on what you're trying to accomplish, so that we can provide the correct steps.

• Can I access HARD Time Capsule disk using my devices iOS or PC?

  I'll buy an AirPort Extreme or airport Time Capsule. So I currently don't have a Mac, can I access the HDD of my iOS devices TC or PC as Network Attached Storage?

  Yes, if you download and install an application like FileBrowser on iPhone and iPad. More details here: Stratospherix - FileBrowser - overview

  Yes, if you open Internet Explorer on the PC and type the IP address of the time Capsule or AirPort Extreme network and press ENTER.   Example... \\192.168.1.10

  If you decide on AirPort Extreme, don't forget to format the USB hard disk in Mac OS Extended journaled.

• Lost access to time capsule

  I have two time capsules and two Airport Express. About two months ago my time capsule rained stopped receiving (always orange flashing). I assumed it was old and was more compatible with El Capitan (10.11.5). Then I went for a month and when I get back home, none of my accessories work. whenever I start the Airport utility, he sees the Capsule of time, then on 'preparation', then "the airport time capsule", "an unexpected error has occurred, please try again." And believe me, I tried! What should I do next?

  Post edited by: L. Jacques Pelletier
  my original post was incomplete.

  Delete all airports in order to have a single...

  Back to the factory and see if you can connect to it. If it is set aside and try the following.

  They should be connected to your modem or router modem by ethernet.

  Have you installed the update from the recent firmware for all airports of your?

  What models are both TC and Express?

  What is the brand and model of your modem main?

• Problem with remote access to Time Capsule

  Hi, I need to set up my APTC in a way to access it on the Internet remotelly.

  I did the following:

  • router Huawei HG622u
    1. activation of NAT
    2. port mapping
       • Protocol: TCP/UDP
       • External start port: 8888
       • End external port: 8888
       • Internal host: the TC's local IP address
       • Internal port: 8888
       • Name of the Air Port TC map
  • APTC (latest firmware installed)
    1. definition of back to my Mac: my Apple ID and password - Green State
    2. definition of APTC in Bridge mode
    3. disc of shared configuration
  • on Mac
    1. definition of back to my Mac - no comment illustrates iCloud

  When I try to access the APTC from the Internet, I see CLTS in Finder/shared section. But when I try to connect, I get the message that the connection failed.

  Could someone advice whot shut I do to make this work?

  Thank you, Eduard

  router Huawei HG622u

  1. activation of NAT

  If it is possible to run your modem without NAT, that is to say fill so that the TC is the main router, will be much more successful than to try to convey the CCMM via a router.

  CCMM if I understand correctly, he must use many more ports... but it is very difficult to get a TC behind a NAT router to work. While Apple says that a computer will work behind a UPNP router, a TC will NOT... There is no UPNP integrated with open ports.

  Get help using Back to My Mac - Apple Support

  Browse through the list...

  TCP and UDP ports used by Apple software - Support Apple products

  the following ports must be open.

  TCP 443

  UDP 500

  UDP 1900

  4488 TCP

  UDP 4500

  5223 TCP

  5350 UDP

  5351 UDP

  5353 UDP

  49512 TO 65535 UDP

  Of course, not all these ports are needed... This is why it is preferable to install the TC in order to open the ports it needs.

  There are other methods of access remotely with the help of the CCMM... and simply transmit AFP TB is the best. I think you're confused or confusing instructions.

  Airport drive - remote (3 methods)

  It seems you are trying to use method 3, but not all do it properly...

  8888 has nothing to do with the CCMM or AFP. Tesserax chose him as a port to be used for the translation of the AFP 548 port. You did no translation of port. There is nothing in the TC to meet 8888... 548 alone will work.

  And this has nothing to do with the CCMM. While let... do try and use both methods of access on top of the other. This gives a big mess.

• I just can't get my Airport time capsule on the internet.

  I bought an airport Time Capsule and a MacBook Air, have set up their, I access my files inside the airport TC, but I can't access the Web, away from home.

  What should I do?

  It is necessary to have a Mac at home connected to access?

  Setup using Airport utility it does not appear to me the ability to access over WAN. How can I do?

  I already configured the back to my mac option.

  Can someone help me?

  Please take a look at the following airport user tip for, at least, three methods to access your Time Capsule from a remote location.

• Restore backup after the reset Time Capsule (1st generation) using Windows PC

  I apologize if this question is somewhere already. I tried to find an answer and I've seen similar discussions but not exactly what I need.

  A bit of history... The location is a small school with about 10 cameras, its network systems, point of sale, cloud networked storage, etc. Was asked by the owner to create or activate a Guest WiFi SSID. They said he worked at the same time, but some work was done by a previous technician and they lost the WiFi of comments.

  So I used the Airport utility to access the time Capsule. However, after the change to the next level (enable the public IP sharing? maybe?), he ended up destroying the entire network, as in nothing was back upward when the utility scanned for devices. Even the Time Capsule was not recognized by the utility. I ended up doing a hard reset on the Time Capsule and do my best to manually configure the device again, even though I was not initially designed the network. I have also discovered that 1st generation Time Capsules have no comments WiFi capabilities.

  To make a long story short (too late... "I know sorry..) .. I got most of the features, functions, etc. on the network back where they were before, with the exception of camera systems and a network storage device active cloud to the owner's House.  What I would like to know is... Since then, I understand that a hard reset does NOT erase the backup or other data on the shared disk in the time Capsule... is there an easy way to restore the settings of all of the time Capsule before the problem occurred?  I would need to do this using a Windows computer.

  Any help will be greatly appreciated. What I'm trying to avoid the most is having to reset all the cameras, which are upstairs, hard to reach areas. I guess that people who were previously assigned on the cameras must still be there. If only I could get the Capsule of time exactly where it was before he went down, which would allow me to save a lot of time and frustration.

  You can also (2nd choice)... If there is a simple way to detect the active network cameras and other devices on the Time Capsule and pull the IP out of them, that would be helpful as well.

  Thanks in advance for answers!

  What I would like to know is... Since then, I understand that a hard reset does NOT erase the backup or other data on the shared disk in the time Capsule... is there an easy way to restore the settings of all of the time Capsule before the problem occurred?

  You have my sympathy all...

  Been to this place before today... and I always get myself into it by pure stubbornness... I should just walk on some of these jobs and tell them too hard...!

  What you had to do was to export the configuration before you start playing. Without export of the configuration there is not much hope of healing to less than the previous tech saved a configuration to the unit... This example gets much delicate.

  The TC is actually able to contain several configurations... There is a good chance, however, that wipe you the.

  Anyway... coming to the serious Tin. (same version on Mac and PC utility should work the same).

  Here's my TC who foolishly a reset.

  

  When I do something... first manual configuration, I wonder is to revert to the previous version.

  

  You have done or could you saved the previous settings as a profile... I hope that you did... in the hope...!

  IF so, you have a saved profile.

  In the area of the top menu go in manage profiles.

  

  

  Now, if you are lucky or did the job just last time... by accident... you'll have a saved profile... Just click back.

  

  If nothing is there, or it's current settings... Sorry, but you didn't know something was there... and you cannot was expected to know the trouble you would get yourself in.

  If you have changed a setting in the TC of the bridge in router mode...

  

  (enable the public IP sharing? maybe?)

  Getting back to what it was... mode bridge being the most common.

  At the bridge of the TC does control most things... and you need to return to the main router.

  If the TC kicking upward a stench to return to the bridge, reset it simply still once and then bridge will work... It would be useful to loads to remember what was the setting... just to see the bridge takes the TC of the equation to know where the cameras are.

  If the cameras are on static IP, they will respond to a ping scanner... If the primary router is configured for a standard range of IP addresses... 192.168.1.xxx some.

  Then the TC in bridge must have also taken an ip address in this range and the cameras (Ethernet or wireless)?

  I hope that ethernet, but if they were using the TC as a wireless access point, unless you know exactly the SSID wireless as it was in the past then you do not have this info...

  Look at any computer, they have in the building that was running wireless and watch all the SSID that they use... one of these is likely the TC and you can restore this name.

  Or drop a camera... and ethernet allows to connect to him... and find the ssid, that it's been fixed... redefine the TC on this name (SSID) wireless security... all cameras must be able to connect to it... and you can then restore the entire system by connecting to the IP address that will be displayed in the list on the main router.

  Good luck.. as says Han Solo... you'll need!

• Time Capsule missing after installing new router

  I recently installed a new wifi router for my home network. Previously, I used only my time capsule to back up data and intend to continue to use it for backups. However, with my new router, I can't find how to access the time capsule to keep backups. I have time capsule directly connected to the router via ethernet and it will still not appear in AirPort Utility or enable Time Machine to find.

  Any suggestions?

  Everything has changed.

  With a new router, you have a 'new' network... and the time Capsule is to remember the parameters which it was equipped to work in your 'old' network The time Capsule is lost and he can't find his way.

  Reset to return to the default settings Time Capsule

  Connect it to the router

  Set up the time again to work with the "new" network Capsule

• I can't access the backups on Time Capsule

  A month ago I deleted from my hard drive and more. I have a MacBook Pro 2012 running macOS. I can't access the files on Time Capsule before is erased in the month of August, I can see the story in the timeline panel, but I don't have access to anything before erasure. Is it possible to access to the files before the wipe?

  A month ago I deleted from my hard drive and more.

  What hard drive you are talking about: one internal on your MacBook Pro (MBP), an external drive attached to the MBP for Time Machine backups, or internal hard drive to time Capsule?

• Sonos access playlists itunes stored on Time Capsule?

  I moved itunes to my file storage folder on my Time Capsule, but when I arrived in Manage > SONOS music library settings, I can not understand how to connect to Time Capsule. I guess I have to select "on a network device such as a network attached storage (NAS)", but I don't know what to do next.

  Help, please!

  Files stored on the Time Capsule, his internal drive or an external drive attached to its USB port, are considered as network drives. If your SONOS application can access network drives, then it should be able to locate these files on the Time Capsule.

  Since I don't have a SONOS device to check, the typical path on the drive would be: \ < name of base station >-< partition or the shared disk name >

• Cannot access hard drive Time Capsule... Password not accepted

  The device ' Time Capsule 802.11n (3rd generation).

  Subject: Unable to connect to the HD TC

  I've reconfigured our old Time Capsule (CT) for use by my daughter dependent of the College.  What with the TC seems to work fine (IE. Internet access and WIFI configured etc...).  I reformatted the HD to start from scratch.  And last updated as indicated by the Airport utility application.  The intention is to create a new WIFI area with backup (Time Machine).

  When you set up Time Machine I stressed the internal HD of TC, and then it says "connecting to etc...".  After a few seconds, a new mold box presents itself to ' enter your password for the server (name of TC) for Time Machine can access.  I enter the HD password I had setup in Airport utility with nothing doesn't.  I checked all passwords with Airport utility "Show passwords".  Tried all the passwords, and of course which none worked.  And Yes, I even try the previous passwords even if I had changed their

  I noticed that using the Airport 6.3.5 utility running on my OS X 10.10.5 machine I can see and change the TC.  But when I use another computer running 10.11.6 is the Airport 6.3.6 utility does not see the TC?

  Thoughts and comments please?

  Next step may be reset to the factory settings, but feel something going on here...

  Thank you

  Kind regards

  Roger

  (1) try to reset the password for the utility disk AirPort

  (2) open TextEdit on the Mac and type the password in plain text in an editor window.  This will allow you to ensure that all the keys on the keyboard are recognized.  I've seen cases where passwords fail again and again because of a problem with a wrong key on the keyboard or a habit of typing that makes you believe that you enter the password one way, but the result is something else.  Be able to actually see that typed password allows to check that.

• My Airport Time Capsule can act as a WIRELESS access point

  Hello.

  I brought a Time Capsule with my Mac Pro. It worked well since yesterday.

  I have set up the time Capsule as a WIFI, bypass at my local network access point. There is a router (cable) works at home.

  It's my Mac Pro AirPort Utility and my iPhone, my Time Capsule is displayed with an exclamation point saying "device not found". I can't connect to the disk on this subject by afp share, or smb. Time Machine function is gone too. He failed trying to connect to the share drive from another computer connected to the time Capsule by cable network.

  But at the same time, WiFi works well.

  I tried to recycle energy. Sharing disk will be available. But if I start the Time Machine backup, it will not be a few seconds.

  Any idea?

  Thank you.

  There are several posts here related the issue.

  Luckily, you have set up your new Time Capsule for Back to My Mac (BTMM)?

  If so, the 'temporary' solution is to delete/disable the option of the CCMM, as follows:

  • Run the AirPort Utility.
  • Select the base and then station, select change.
  • On the tab of the Base Station, go back to the section of my Mac at the bottom of the window.
  • If you have entries here, select it and click then the minus sign "-" button to remove it.
  • Click on update and allow the base station restart.

  If you have not enabled CCMM, we have other options for you to try.

• Access the 4th generation Time Capsule data remotely in Mac and PC

  Hi all

  I intend to log in case Apple support, but my Service and Support coverage is already expired > _ <.

  Apple PC does not support mobile devices like IOS or android, so in this top, I'll focus on Mac and PC.

  Appreciate if you guys could give me advice on how to set it up properly.

  Material and Configuration:

  -ASUS RT-AC5300

  Firmware version: last 3.0.0.4.380_3341 - g25420f5

  IP: 192.168.1.1

  -Configured Port forwarding, Port 548 to 192.168.1.85 in ASUS router

  -Time Capsule from Apple 4th generation (Firmware version: 7.6.7 last)

  IP: 192.168.1.85

  -Cable for direct LAN connection between TC Apple and ASUS router

  I can access my Apple TC LAN for PC and Mac (for PC, installed the Base Station Agent from the airport, for Mac, I access it via the Finder with credentials for password)

  Tried several times to set the TC to be able to access remotely to both Mac and PC platform, also read many articles, no luck.

  Grateful if someone here can guide me on how to configure it so that it works correctly.

  Screenshots below for Apple TC settings:

  http://i2.Photobucket.com/albums/Y25/TerenceNHK/Apple/base%20Station.PNG

  http://i2.Photobucket.com/albums/Y25/TerenceNHK/Apple/Internet.PNG

  http://i2.Photobucket.com/albums/Y25/TerenceNHK/Apple/wireless.PNG

  http://i2.Photobucket.com/albums/Y25/TerenceNHK/Apple/network.PNG

  http://i2.Photobucket.com/albums/Y25/TerenceNHK/Apple/disks.PNG

  Thank you very much!

  Kind regards

  Terence

  In your Mac, in the finder, use Go, connect to the server.

  Type of AFP://yourpublicIP

  Download your public IP address of the router asus news... remote WAN you should use DDNS... iCloud is useless... disable in the TC... It does not work behind another router for most people.

  But you must use the public IP address or DDNS address... It is available in the Asus firmware. Best is to buy a static public IP address from your ISP... This is the only reliable method... is worth a bit of money on a dynamic IP.

  This is unnecessary for Windows computer... Access SMB is usually blocked by ISP and Windows does not support AFP.

  Please post your pictures directly here... It's so much easier, then, for us to see.

  

• Airport Time Capsule 2 TB blocking my internet access.

  I just bought a new airport Time Capsule 2 TB. When it is plugged in and running, I lose access to the internet! There is a wifi wireless in the House. What is the cause?

  There is a wifi wireless in the House. What is the cause?

  Potentially, Yes. Network Wi - Fi of the new Time Capsule can interfere with this other Wi - Fi router. What is the brand and model of the other device? What are your objectives of networking for the Time Capsule (TC)? In other words, do you want to expand the wireless of the other device, or create another Wi - Fi network, or something else?

• Is it possible to remote access to files on airport time capsule without a great second computer mac at home?

  Hello!

  I read the articles on access distance to another mac, but what I need is to remote access to files on airport time capsule without a great second computer mac at home.

  Only Mac... Mac you will use for remote access to files on the Time Capsule... is necessary.

  Set up and use Back to My Mac