No connection after installing windows 7 from Windows xp.

Similar Questions

• Program Compatibility Assistant popping up on each connection after installing windows 8

  install windows 8 on my laptop (HP Pavilion Notebook PC g6) but keep getting a popup saying I need to install the ATI Catalyst Control Center, I do a search and it says to contact ATI, but solutions at home? any suggestions?

  Hello

  Contacting ATI (AMD) would not help because you need a stamp certified HP to be able to run on your computer. My suggestion: check out the complete model (G6 is not a model) of your machine and go to the (x) HP to check. Many drivers have been downloaded in support of the sites for these days.

  I hope this helps.

• S3-951: terrible Wi - Fi connection after installing Windows 7

  Hello

  On Monday of this week I bought a new SSD that I used to replace the HARD drive of my Acer Aspire S3 (long out of warranty, unfortunately). Therefore, I had to install new Windows 7 and download all the drivers from the Acer site. However, while before I got the WiFi connection at full power, now I get only one bar, and if I move slightly in the whole House, the connection would be lost and even report no network in sight.

  Could someone help me find a solution to this problem? I don't have access to my recovery partition, otherwise I would have just used it to restore the settings by default when the wireless adapter worked flawlessly.

  Thank you in advance!

  There is a possibility of wire antennas came out the wifi card. You can access it by removing the 12 screws holding the bottom and gently lift the back. If it sticks, use a pick or a card plastic to clear out gently. Be aware of the static elect. damage. Look it up.

• Satellite C850-1GL - no Wi - Fi connection after installing Windows 8.1

  Hello to you all!

  I necessarily need your help! A few days ago, I've upgraded to 8.1 Windows 64 bit on my laptop Toshiba Satellite C850-1GL and are identified is no longer available wi - fi networks.

  I installed all drivers as specified by Toshiba (drivers are updated the most recent versions available).
  With windows 7 64-bit and 64-bit windows 8 wi - fi networks have been identified without any problem.
  My wi - fi network card is Realtek 8188CE.

  Please help me, I don't know what to do.

  Forgive my broken English.

  Thanks for your attention!

  Hello

  Wireless network adapter installed and listed correctly in the Device Manager?
  Don't forget the wireless network adapter is enabled properly (not in airplane mode).

• No Internet connection after installing Windows 7

  I have the same problem as others with Windows Media Center AND IE 8, no internet connection. It works find with Firefox and Safari, but I can't get internet connectivity with IE 8, Windows Media Center, and Realplayer. It worked fine before 'redevelopment' of W7.

  See http://social.answers.microsoft.com/Forums/en-US/w7network/thread/e0e0d320-b6d1-4239-a6f6-afbe47072332 ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• Unable to connect after installing Windows Update

  Just did, and she came back

  Stan

  Gloria Guest administrator

  Just did and she came back:

  Administrator

  Stan                                    Gloria                                      Guest

• Error message: Ethernet is not a valid ip address configuration and cannot connect to the Internet after installing Windows 8.

  Original title: Internet not working after installing Windows 8. Help, please

  I installed Windows 8 a week before, which had Windows Vista. When I was with Vista, I had no problem with the Internet, I had. But shortly after I installed Windows 8, the problem began. The connection is hardly 2 minutes. In addition, it is not navigate beyond my home page. After troubleshooting the result came as Ethernet is not a valid ip address configuration. It makes me really frustrated. After all, I was looking forward to navigate in windows 8, this problem makes me think really bad. If someone could help me, it will be grateful to you.

  Manorajan respected,

  I too had d same problem but I solved it later on myself.
  Here's how to: -.
  1-make sure you have intel network driver I installed your windows it pc. Download (on any other pc and transfer and install in it) and install it in your pc respective windows 8. Here is the link to download:-http://drivers.softpedia.com/get/NETWORK-CARD/INTEL/Intel-Network-Adapter-Driver-172-for-Windows-8.shtml
  Den DOWNLOAD realtek lan driver here to install http://drivers.softpedia.com/get/NETWORK-CARD/REALTEK/Intel-Realtek-LAN-Driver-80030730-for-Windows-8.shtml..if in the installation of theres no error ignore it... do not panic and reinstall... as it is already installed

  2 - unplug your LAN cable and Wi - Fi

  3 - go to network and sharing den center left side d click on change adapter settings clik left on the network card intel

  4-go to "Ethernet Adapter local area connection' properties and Deselect"Internet Protocol Version 6 (TCP/IPv6) "

  "5 - Select" ""Protocol Internet Version 4 (TCP/IPv4) '

  Press the properties button

  6 - Select "use the following IP address:" option and set this ips

  IP = "ip address".

  subnet mask = 255.255.255.0

  default gateway = your ip from the router (you can recheck all say on any other pc having a successful conection even wid tell by checking the properties of dial-up connection or any smart phone like any iphone or android mobile, if it is used as a wifi too in led staus/properties to your respective wifi name)

  7. in the second section select "use the following DNS server address:"

  Set "Server DNS PreferAlternate:" your router ip that entered u in "default gateway of" this. " pinterested ok and try to connect in wireless lan

• Please, please help. No sound from my sound card on board after installing windows 7

  I just installed windows 7 ultimate 64 bit on my computer that previously had windows xp professional sp3 top.  My motherboard, what I don't know, is an a32gv11c from ASUS with a team of a soundcard SoundMax.  I have absolutely no sound and can't seem to find the drivers for it anywhere.  Y at - there anyone out there that can help me to find the driver I need to get a sound?  Help, please.  Thank you.

  I know it's my advice, which means that the hardware manufacturer, who has done this.  The installation for the integrated sound card cd says that the current operating system is not supported, which to me makes sense because this material was released before windows 7.

  All documentation is in stock and not accessible.  I looked inside to the motherboard and can't seem to find any useful information pertaining to the brand of it...  I never spent by with any programs driver utility because my model did not appear.

  Issues that everyone seems to have is with no sound from sound card after installing windows 7, not just isolated to my sound card.  I have a hard time believing I am eternally screwed with no sound from my computer because of my hardware not supported under windows 7.  There must be a solution out there.  I realize that I should have found that now but can not which is what brought me to this forum.  Someone knows and can help me.

  You are not 'for always screwed"- you can always buy and install a sound card which the manufacturer supports their product under Windows 7 - operating system, you choose to run.  The trick is to have a piece taken in charge (by the manufacturer) hardware or software - * under the operating system you choose to run *.

  Yep - you've had this old Ford Mustang you bought this Nitro kit for... But now that you have this new Ford Mustang - Nitro kit may not work.

  Your only real solution: get a piece of hardware - audio device - supported under Windows 7 by its manufacturer.  Else do you play with fire, may or may not work and even if it does not, could be broken by the next patch or update.  If you have a PCI or PCIe available slot, find a cheap good sound card (trust me - the one you had would have qualified as cheap) and throw it in.  15 USD and up to I guess.

• I don't see the desktop icons after installing Windows updates.

  Original title: connection user init failure

  I m using windows 7 pro. After installing the updates, I have problem with the icon on the desktop .i has no icon on the desktop when you connect. get the message the CONNECTION USER INIT FAILED. After pressing ALT + CTRL + delete > taskmanager > run > Desktop Explorer icons is displayed... .i tried many time to solve this problem of the customer service, but they are unable to solve this problem. Please please help

  It is not possible for me to every time the format of the system

  kindly, please give solution.

  My system is connected to the network with 3 PCs and all are licensed copy.

  Hello

  Welcome to the Forums Community Microsoft and thanks for posting the question.

  According to the description, you get an error message "FAILED CONNECTION USER INIT" after installing Windows updates.

  From my research, this problem occurs if the Userinit key in the Windows registry has been changed. For example, this problem may occur if the Userinit key has a value, but no binary data.

  I suggest you follow the steps mentioned below.

  Method 1:

  Step 1: Start the computer in safe mode

  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

  Step 2: Check the value and binary Userinit registry data

  Important: The following instructions contain the steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information, view the article in the Microsoft Knowledge Base:

  Back up the registry
  http://Windows.Microsoft.com/en-us/Windows7/back-up-the-registry

  a. start Registry Editor. To do this, click Start, type regedit in the search box and press ENTER.

  b. click continue.

  c. Locate and then click the following registry key: HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon

  d. in the right pane, right-click Userinit, and then click change.

  e. in the value data box, type hard disk:\Windows\System32\userinit.exe, and then click OK.

  Note: The placeholder of the hard drive refers to the drive on which Windows Vista is installed.

  f. close the registry editor.

  g. restart the computer.

  Method 2:

  Restore the system to an earlier point before installing this application.

  
  http://Windows.Microsoft.com/en-us/Windows7/what-is-system-restore
  System Restore can return your files system to a point in time before you noticed a problem, without affecting documents, photos, or other personal files. If the system restore does not resolve the problem, you can undo the restore operation and choose a different restore point.
  
  More information on:
  
  System Restore: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows7/system-restore-frequently-asked-questions

  Hope this information helps. Get back to us if you have more queries about Windows.

• SD card is not working properly after installing windows 10

  I have a MacBook Pro (retina, 13 inches, early 2015) with EL Capitan 10.11.5 and after I installed 10 windows using bootcamp, everything worked fine at first, but after I deleted my part of windows and then installed windows 10 the second time, the SD card is not working properly. She mounts only if the computer shuts down first, and then start. If I take the laptop directly, the SD card will not rise. The same thing happens when I switch systems using a control option key or bootcamp Center where when I switched to another system, the SD card that was mounted on the old system does not appear in the new system. I was trying to solve this problem remove the part of windows before you reinstall it again once, so I found that after I deleted the windows part, the problem is gone and it reappeared after installing windows 10 even once. I also found that after I installed windows the total volume of hard drive (128g front) became 121g.

  Hello LorinMax,

  Thanks for this info and choosing the communities Support from Apple. I know the importance of your work with your Macbook Pro SD card!

  If I understand correctly, you cannot use your SD card, unless you stop and then restart. Because this behavior started when you installed Boot Camp, I would start with the following steps:

  1. first of all, start by repairing your hard disk in disk utility to correct the unexpected problems that could be the cause of this behavior.

  Disk utility (El Capitan): a disc repair

  2. use Mode without fail to start up your Mac so that it performs certain checks, remove files from the system cache, check your startup disk and trying to fix problems if necessary directory.

  Try safe mode if your Mac does not end commissioning

  Graphics performance limited in recovery of OS X or in safe mode

  3. According to Boot Camp Installation & Setup Guide, you may need to back up your personal data and reinstalling OS X, then reinstall Windows via Boot Camp and related support files.

  Boot Camp Installation & Setup Guide

  Backup of your Mac hard drive

  OS X: on OS X Recovery

  See you soon!

• HP Officejet 7612: analysis of problems after installing Windows 10

  After installing Windows (prior to Windows Vista) 10, scan documents with my HP Officejet 7612 became a hell of a job.

  Printing is no problem.

  With Webscan, I can only scan and save 1 page at a time, I can not scan several pages of the document 1 more.

  I downloaded "Extended Scan" but when I try to use this app, it says "year error occurred while scanning" without more information.

  With "HP Scan and capture" I can't scan the size of A3 paper full of documents and there seems to be no possibility to change the size of a3 paper. Maximum size is 'legal letter '.

  Same problem with "Windows Fax and scan."

  Are there other ways to recover the possibilities of full scan from my HP Officejet 7612?

  Hello
  
  Thank you for using the HP Forums.
  
  You can download and install the software COMPLETE features of HP printing for your operating system:

  The following resources will help you:
  
  HP printer install wizard for Windows
  http://ftp.HP.com/pub/softlib/software13/COL50403/MP-150580-2/hppiw.exe
  
  Once you have downloaded and installed the software, FULL of features, you will be able to print and scan.
  
  Hope that helps.

• How can I do I check Windows Update after installing Windows 7 if my internet interface does not work?

  My only internet connection is done by an AT & T USB Connect 881U (mfg Serra wireless). Windows 7 update Advisor indicates that

  I need to check Windows Update after installing Windows 7 to make sure that I have the latest driver for this device, otherwise it can not work.
  If this does not work I have no way of checking Windows Update. Any suggestions of how I could get out of this situation if it happens.

  When all else fails RTFM:

  Install the Windows updates:
  http://Windows.Microsoft.com/en-us/Windows7/install-Windows-updates

  Update your computer:
  http://Windows.Microsoft.com/en-us/Windows7/updating-your-computer

  Understand the Windows automatic update:
  http://Windows.Microsoft.com/en-us/Windows7/Understanding-Windows-automatic-updating

  Updates: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows7/updates-frequently-asked-questions

  Change how Windows installs or notifies you of updates:
  http://Windows.Microsoft.com/en-us/Windows7/change-how-Windows-installs-or-notifies-you-about-updates

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• After installing windows XP sp3 do not work my motherboard drivers intel

  After installing windows XP sp3 my motherboard drivers intel do not work. My mother board D845 GLAD. What could be the problim?

  Try reinstalling the drivers for your motherboard chipset, you can check this link to download the chipset driver:http://downloadcenter.intel.com/SearchResult.aspx?lang=eng&ProductFamily=Desktop+Boards&ProductLine=Intel%c2%ae+845+Chipset+Family+Boards&ProductProduct=Intel%c2%ae+Desktop+Board+D845GLAD

  Also, try to download the drivers from your computer manufacturer site... Their number is 800-936-5700, and they are open Monday - Friday, 05:00-21:00 Pacific, Saturday & Sunday, 06:00 - 15:00 PST. XD

• Does not fingerprint after installing Windows 7

  I bought 3 items of T500 with installed Windows 7 Home. With this OS footprint scaner worked properly.

  After installing Windows 7 Professinal, fingerprint reader does not work. All instaled divers. There is no error in DeviceManager. But when I run the software of fingerprints, it is said that scanner is not lit.

  Make sure that the installed driver is actually the one that came with the Lenovo Fingerprint Software and not the one that you got from Windows Update. I've seen similar problems several times where Windows 7 is installed and get fingerprints from windows update driver/software and the software Lenovo to fingerprints do not work because some parts of the software, I got from windowsupdate is left on the computer.

  Which version of the driver of the fingerprint reading is installed on your computer?

  You can try uninstalling Lenovo Fingerprint Software and restart. Then, after the reboot if there is still a driver installed for the fingerprint reader in Device Manager, right click and select uninstall and also check the box that says to delete the driver. You may have to restart again. If you had several drivers fingerprint installed you may need to repeat this step twice. So when Device Manager shows the fingerprint with no check reader driver installed if you have any software fingerprint authentec or authentec truesuite installed under "uninstall or change a program". If you find any uninstall and restart. If you can successfully eliminate all the reader of fingerprints in the device should be listed in Control Panel with no driver installed, you should find any substance of fingerprints or biometrics. Then try to install the Lenovo Fingerprint Software.

  -gan

• OfficeJet 6500 nit scanner works after installing windows 7

  Is there a fix for Officejet 6500 scan does not not after installing windows 7?

  Hello

  Driver and applications in support of Windows 7 can help. You can download from the following link:

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?CC=au&LC=en&DLC=en&product=3795314

  Kind regards.