S3-951: terrible Wi - Fi connection after installing Windows 7

Similar Questions

• Program Compatibility Assistant popping up on each connection after installing windows 8

  install windows 8 on my laptop (HP Pavilion Notebook PC g6) but keep getting a popup saying I need to install the ATI Catalyst Control Center, I do a search and it says to contact ATI, but solutions at home? any suggestions?

  Hello

  Contacting ATI (AMD) would not help because you need a stamp certified HP to be able to run on your computer. My suggestion: check out the complete model (G6 is not a model) of your machine and go to the (x) HP to check. Many drivers have been downloaded in support of the sites for these days.

  I hope this helps.

• Satellite C850-1GL - no Wi - Fi connection after installing Windows 8.1

  Hello to you all!

  I necessarily need your help! A few days ago, I've upgraded to 8.1 Windows 64 bit on my laptop Toshiba Satellite C850-1GL and are identified is no longer available wi - fi networks.

  I installed all drivers as specified by Toshiba (drivers are updated the most recent versions available).
  With windows 7 64-bit and 64-bit windows 8 wi - fi networks have been identified without any problem.
  My wi - fi network card is Realtek 8188CE.

  Please help me, I don't know what to do.

  Forgive my broken English.

  Thanks for your attention!

  Hello

  Wireless network adapter installed and listed correctly in the Device Manager?
  Don't forget the wireless network adapter is enabled properly (not in airplane mode).

• No Internet connection after installing Windows 7

  I have the same problem as others with Windows Media Center AND IE 8, no internet connection. It works find with Firefox and Safari, but I can't get internet connectivity with IE 8, Windows Media Center, and Realplayer. It worked fine before 'redevelopment' of W7.

  See http://social.answers.microsoft.com/Forums/en-US/w7network/thread/e0e0d320-b6d1-4239-a6f6-afbe47072332 ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• No connection after installing windows 7 from Windows xp.

  I have no internet connection and no volume!

  One of my friends said this is a new installation and I need to go on the manufacturer's website and download the driver? How in the world am I supposed to intall them if I don't have a connection? !!!

  And where is the Web site of the manufacturer of?
  I have a windows xp media center edition.
  PLEASE HELPPPP

  If AusteK don't list the drivers for WinXP, even, I would say you will be out of luck and need to consider changing your hardware

• Unable to connect after installing Windows Update

  Just did, and she came back

  Stan

  Gloria Guest administrator

  Just did and she came back:

  Administrator

  Stan                                    Gloria                                      Guest

• Error message: Ethernet is not a valid ip address configuration and cannot connect to the Internet after installing Windows 8.

  Original title: Internet not working after installing Windows 8. Help, please

  I installed Windows 8 a week before, which had Windows Vista. When I was with Vista, I had no problem with the Internet, I had. But shortly after I installed Windows 8, the problem began. The connection is hardly 2 minutes. In addition, it is not navigate beyond my home page. After troubleshooting the result came as Ethernet is not a valid ip address configuration. It makes me really frustrated. After all, I was looking forward to navigate in windows 8, this problem makes me think really bad. If someone could help me, it will be grateful to you.

  Manorajan respected,

  I too had d same problem but I solved it later on myself.
  Here's how to: -.
  1-make sure you have intel network driver I installed your windows it pc. Download (on any other pc and transfer and install in it) and install it in your pc respective windows 8. Here is the link to download:-http://drivers.softpedia.com/get/NETWORK-CARD/INTEL/Intel-Network-Adapter-Driver-172-for-Windows-8.shtml
  Den DOWNLOAD realtek lan driver here to install http://drivers.softpedia.com/get/NETWORK-CARD/REALTEK/Intel-Realtek-LAN-Driver-80030730-for-Windows-8.shtml..if in the installation of theres no error ignore it... do not panic and reinstall... as it is already installed

  2 - unplug your LAN cable and Wi - Fi

  3 - go to network and sharing den center left side d click on change adapter settings clik left on the network card intel

  4-go to "Ethernet Adapter local area connection' properties and Deselect"Internet Protocol Version 6 (TCP/IPv6) "

  "5 - Select" ""Protocol Internet Version 4 (TCP/IPv4) '

  Press the properties button

  6 - Select "use the following IP address:" option and set this ips

  IP = "ip address".

  subnet mask = 255.255.255.0

  default gateway = your ip from the router (you can recheck all say on any other pc having a successful conection even wid tell by checking the properties of dial-up connection or any smart phone like any iphone or android mobile, if it is used as a wifi too in led staus/properties to your respective wifi name)

  7. in the second section select "use the following DNS server address:"

  Set "Server DNS PreferAlternate:" your router ip that entered u in "default gateway of" this. " pinterested ok and try to connect in wireless lan

• How can I do I check Windows Update after installing Windows 7 if my internet interface does not work?

  My only internet connection is done by an AT & T USB Connect 881U (mfg Serra wireless). Windows 7 update Advisor indicates that

  I need to check Windows Update after installing Windows 7 to make sure that I have the latest driver for this device, otherwise it can not work.
  If this does not work I have no way of checking Windows Update. Any suggestions of how I could get out of this situation if it happens.

  When all else fails RTFM:

  Install the Windows updates:
  http://Windows.Microsoft.com/en-us/Windows7/install-Windows-updates

  Update your computer:
  http://Windows.Microsoft.com/en-us/Windows7/updating-your-computer

  Understand the Windows automatic update:
  http://Windows.Microsoft.com/en-us/Windows7/Understanding-Windows-automatic-updating

  Updates: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows7/updates-frequently-asked-questions

  Change how Windows installs or notifies you of updates:
  http://Windows.Microsoft.com/en-us/Windows7/change-how-Windows-installs-or-notifies-you-about-updates

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• I don't see the desktop icons after installing Windows updates.

  Original title: connection user init failure

  I m using windows 7 pro. After installing the updates, I have problem with the icon on the desktop .i has no icon on the desktop when you connect. get the message the CONNECTION USER INIT FAILED. After pressing ALT + CTRL + delete > taskmanager > run > Desktop Explorer icons is displayed... .i tried many time to solve this problem of the customer service, but they are unable to solve this problem. Please please help

  It is not possible for me to every time the format of the system

  kindly, please give solution.

  My system is connected to the network with 3 PCs and all are licensed copy.

  Hello

  Welcome to the Forums Community Microsoft and thanks for posting the question.

  According to the description, you get an error message "FAILED CONNECTION USER INIT" after installing Windows updates.

  From my research, this problem occurs if the Userinit key in the Windows registry has been changed. For example, this problem may occur if the Userinit key has a value, but no binary data.

  I suggest you follow the steps mentioned below.

  Method 1:

  Step 1: Start the computer in safe mode

  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

  Step 2: Check the value and binary Userinit registry data

  Important: The following instructions contain the steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information, view the article in the Microsoft Knowledge Base:

  Back up the registry
  http://Windows.Microsoft.com/en-us/Windows7/back-up-the-registry

  a. start Registry Editor. To do this, click Start, type regedit in the search box and press ENTER.

  b. click continue.

  c. Locate and then click the following registry key: HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon

  d. in the right pane, right-click Userinit, and then click change.

  e. in the value data box, type hard disk:\Windows\System32\userinit.exe, and then click OK.

  Note: The placeholder of the hard drive refers to the drive on which Windows Vista is installed.

  f. close the registry editor.

  g. restart the computer.

  Method 2:

  Restore the system to an earlier point before installing this application.

  
  http://Windows.Microsoft.com/en-us/Windows7/what-is-system-restore
  System Restore can return your files system to a point in time before you noticed a problem, without affecting documents, photos, or other personal files. If the system restore does not resolve the problem, you can undo the restore operation and choose a different restore point.
  
  More information on:
  
  System Restore: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows7/system-restore-frequently-asked-questions

  Hope this information helps. Get back to us if you have more queries about Windows.

• SD card is not working properly after installing windows 10

  I have a MacBook Pro (retina, 13 inches, early 2015) with EL Capitan 10.11.5 and after I installed 10 windows using bootcamp, everything worked fine at first, but after I deleted my part of windows and then installed windows 10 the second time, the SD card is not working properly. She mounts only if the computer shuts down first, and then start. If I take the laptop directly, the SD card will not rise. The same thing happens when I switch systems using a control option key or bootcamp Center where when I switched to another system, the SD card that was mounted on the old system does not appear in the new system. I was trying to solve this problem remove the part of windows before you reinstall it again once, so I found that after I deleted the windows part, the problem is gone and it reappeared after installing windows 10 even once. I also found that after I installed windows the total volume of hard drive (128g front) became 121g.

  Hello LorinMax,

  Thanks for this info and choosing the communities Support from Apple. I know the importance of your work with your Macbook Pro SD card!

  If I understand correctly, you cannot use your SD card, unless you stop and then restart. Because this behavior started when you installed Boot Camp, I would start with the following steps:

  1. first of all, start by repairing your hard disk in disk utility to correct the unexpected problems that could be the cause of this behavior.

  Disk utility (El Capitan): a disc repair

  2. use Mode without fail to start up your Mac so that it performs certain checks, remove files from the system cache, check your startup disk and trying to fix problems if necessary directory.

  Try safe mode if your Mac does not end commissioning

  Graphics performance limited in recovery of OS X or in safe mode

  3. According to Boot Camp Installation & Setup Guide, you may need to back up your personal data and reinstalling OS X, then reinstall Windows via Boot Camp and related support files.

  Boot Camp Installation & Setup Guide

  Backup of your Mac hard drive

  OS X: on OS X Recovery

  See you soon!

• Satellite Pro U200 - no sound after installing Windows 7

  Hello

  I have a problem with sound after installing Windows 7 on a (PLUA1E) satellite Pro U200. No Win7 audio driver available on the Nordic pilot site. Help, please.

  G.Magnason

  Hey Buddy,

  Have you already checked the site Web of Toshiba itself?
  http://EU.computers.Toshiba-Europe.com

  I found a driver for Vista 32 bit and Vista drivers most also work on Windows 7 so it s worth a try! :)

• HP pavilion zv5000: missing zv5000 system drivers of base after installing windows 7

  After installing windows 7 displays device management point exclaimation

  Hardware ID:

  PCI\VEN_104C & DEV_8201 & SUBSYS_006B103C & REV_01
  PCI\VEN_104C & DEV_8201 & SUBSYS_006B103C
  PCI\VEN_104C & DEV_8201 & CC_088000
  PCI\VEN_104C & DEV_8201 & CC_0880

  Also CD-ROM/DVD-rom won't recognize my cd/DVD, but Device Manager shows the work of the unit.

  Need help

  Hello:

  You can use the driver card reader XP support for your laptop and driver page.

  There is no vista or W7 driver for this card reader.

  If auto installation does not work, manually install the driver.

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-29677-1 & CC = US & DLC = in & LC = on & os = 228 & Product = 385148 & sw_lang =

• Computer OS used to start after installing windows 10

  Hello im having problem starting my system after installing windows 10. I did the install and it worked fine since the upgrade to 8.1. But then I tried to format the drive and in the menu format, he's stuck at 2%, and then I restarted the computer. Now it will hang at the hp logo and go back to the same logo. Do I have to replace my hard drive?

  What I understand, if you have completed the 10 Windows Installer and everything has happened until the end, then you are supposed to be able to do a clean install with the download of Windows 10 DVD or USB.  With a working computer, GO to THIS PAGEand scroll down to the button "download tool" selection the 64-bit version.  Once clicked, it will ask you if you want a DVD or USB for the iso.

  Once it's done and you have the DVD or the USB version, see if you can install Windows 10.  If this fails, you may need to replace the hard drive.

• Satellite P300-1This - Microphone does not work after installing Windows 7

  Hello world.

  At first, I'm sorry for my bad English, so I will say in no time.

  A few days ago, I removed a few programs, and I installed the new Windows 7 operating system. Everywhere I had to download the new drivers for the camera because they do not work. After you download the drivers of the camera, the camera become operative (YES!), but later worked for me, a built-in microphone was out of use. What may be of it with the cause and this driver to download and why the microphone not working?

  I can't talk with friends on Skype ;( Help me. I hope you know what I'm saying.

  Hello

  Do you really install any drivers after installing Windows 7? Maybe you have forgotten something and so it doesn t work.
  Micro is a part of webcam so be sure that driver webcam is properly installed and driver sound, you need to as well.

  After that, check the sound settings. Make sure that the Microphone is enabled and test it again with amp active microphone.

• No sound on HP Pavilion a6077c desktop pc speakers after installing Windows 7 premium Home

  No sound on HP Pavilion a6077c desktop pc speakers after installing Windows 7 premium Home. Any suggestions on how to solve the problem?

  Thank you. This site help me solve my problem.

  http://www.Realtek.com.tw/downloads/ExpressFTPSite.aspx?DownTypeID=3 & DownID = 558 & PFid = 23 & Conn = 3