No detected boot device

Similar Questions

• Cannot detect the boot device after factory new HARD drive format

  First of all, I have a HP Pavilion G6 I bought in December 2012. Yesterday, I decided to make a new record HARD to upgrade and start over. It is a hybrid SSD + HDD 1 TB of Seagate. It installed without a hitch, and I used my HP recovery CD to make a factory disk formatting.

  He finishes, reboot, but instead to restart the HP Windows 8 installation screens, he goes to what looks like Windows 8 course mode with a box containing the date, time and he said something in the sense of 'Installing the driver HP diagnostics' with an OK. By clicking on that or didn't disappear, and there is a command line bar in the lower left corner of the screen.

  The screen becomes a HP screen that begins to install the drivers. It ends and restarts to a black screen that says "no boot device not detected, please install OS."

  I did a disk check and that's fine. I swapped my reader, and it loads fine. In fact, it's what I use now for this type.

  What could be the problem here? The boot order has never changed in the BIOs. If it was the faulty connector I doubt he would charge the reader who was always in the computer. Load disc newly formatted in an external case indicates that Windows 8 is indeed on this subject, but on a 93GB partition even if the disc is 1 TB.

  I'm in a stalemate here, and nobody seems to know what to do!

  It was indeed the hybrid propulsion system. I exchanged for a normal HARD drive and resetting factory completed without a hitch. It was the mistake on my part! I never guessed it would have been the problem.

• I get the message "No. Boot Device Detected" in Vista

  I changed the battery in Dell Dimension e521 my mother.  Then when booting I get the message "No boot device found". I can continue and boot from the CD.  I tried to Dothe StartRepair bt he indicated there is no problems.  How can I fant6mes the startup problem?

  Hello

  Installation/configuration (BIOS/CMOS) often F2 as you boot then watch the screen - make sure that the hard drive is set
  first of all in the boot order.

  Check with Support from Dell, their online documentation, diagnosis and ask in their forums on any
  known issues.

  Dell support
  http://support.Dell.com/

  Dell support drivers - product manual & warranty Info (left side) - and much more
  http://support.Dell.com/support/index.aspx?c=us&l=en&s=DHS

  Dell forums
  http://en.community.Dell.com/forums/

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Lion broke Fusion - no boot device has been detected.

  Everything was wonderful until the Lion has eaten my Windows OS...

  I can start to Win 7 under Bootcamp without problem, but when I try to start windows 7 under the terms of the merger, I now get an error message that says no boot device has been found. Here is a screenshot. And Yes, I did uninstall/reinstall merger with the more recent version.

  Any help would be most appreciated.

  Thank you

  Brad

  This is a known issue because the installation of Mac OS X Lion modifies the partition table and all what you need to do is delete the Virtual Machine Boot Camp and add it to the back of the Virtual Machine library.

  Take a look at: VMware Fusion 3 support for Mac OS X Lion (10.7)

  • Boot Camp partitions is not accessible through Fusion after upgrade to Lion.

  To work around this problem, delete the virtual machine Boot Camp of the library and recreate it. For more information, see the virtual machine to Boot Camp fails to turn on with a disk (1003483) error.

• HP Pavilion 15 t-n200: sometimes not found black screen boot device

  Computer during the race will go sometimes to black screen and say "boot device not found", I am able to

  correct the problem by power off, wait a few seconds back, computer power will start

  Save as normal and work very well.  This happens maybe once a week. My fear is of course to some

  time not to come back to the top. Are there corrective measures, should I try now? I have a hybrid

  static hard drive (ST500LM000-1EJ162)...

  .

  Hello @jla11,

  Thank you for visiting the HP Forums! The Forums are a great place where you can find solutions for your problems, with the help of the community!

  I understand that you have a problem with the laptop to a black screen and tried to help you!  I see that you will get the error on the hard disk.

  You might try to test the hard drive for the failure.  In this way, you can check if there are problems.  You can use the following to help:

  Laptops HP - device not found Boot error or hard drive not detected

  You should be able to skip to step 2.  Please post back with the results.

  Please let me know if this information helps you solve the problem by marking this message as 'accept as Solution', this will help others easily find the information they seek.  In addition, by clicking on the Thumbs up below is a great way to say thank you!

  Have a great day!

• Satellite showing C55-5-137: no boot device please don't restart

  Hello
  Just bought a computer portable satellite c55-5-137 and when I start the computer shows this message: no boot device - please reboot the system.
  Tried to boot from usb win7, same message. Also in bios I don't have the option to disable secure boot, the only option is uefi (grayed out). Need help .

  I assume that the HARD drive is not visible somehow for your system.
  When you enter the BIOS disk HARD is listed and detected correctly?
  Try to set the BIOS to default settings and check again.

• HP laptop: when I start my laptop it will be showing "no boot device."

  When I start my laptop it will be showing "no boot device."

  Hey @Swapvb

  First of all, I want to you welcome to the Forums of HP Support! On the forums, you will find solutions, suggestions and helping hands!

  I understand that you can't your laptop because you do not receive a message from boot device.

  The error message says "Boot Device not found"? If so, please use the Boot Device found not or Hard Drive not detected error document.

  Here, I have provided a list of measures to try with an additional documentation if you need. Please try to:

  • Perform a hard reset
  • Restore the default settings of the BIOS
  • Perform a test equipment
  • Reconnect the hard drive

  If none of the steps above troubleshooting solved the error condition, please make sure that you back up your personal data from your laptop, and then try again to perform a HP system recovery again.

  If the recovery of the system is not yet functioning, please use the document Troubleshooting an HP System Recovery .

  If this answer helped, please use the button accept as a Solution . If you want to give me a five high virtual, please click the Thumbs Up icon below.

  If you need assistance, I would be more than happy to continue to help you. Please re-post with the results of troubleshooting as well as your model number (How can I find my model number or product number?).

  Thanks for joining the community of support HP!

  Have a great day!

• Satellite C50-A0413 - no boot device - restart System

  Satellite C50-A0413 that was installed with Win8 pr but I didn't like it so I decided to downgrade it so that I can install Win7.

  I formatted the HARD drive and then installed Win7 on the HARD drive. Everything happened until perfect present, but do not forget that the HARD drive was working on another machine, so when I put it back for the things of my laptop went bad because the machine couldn't detect my drive again. Is he didn't keep show no boot device - restart System. What has tried to remedy the situation? Press f2 to access my utility set up 'Security' tab and change the value of the "Secure Boot" option to "Disabled" then the System Configuration but I can't find Boot Mode to change the UEFI to CSM.

  What do I do please help?

  Sorry, but your ad is quite confusing. If I understand you right, you have installed Win7 on X computer and then removed HARD drive in your C50-A0413 Satellite and now you wonder why Win7 won t start correctly or how understand this?

• HP 15-g030so: the selected boot device has failed. Press ENTER to continue

  So, I got a disc error and had to go on my hard drive. After that, I was invited by a certain recovery of hp and tool that fussed around a while and rung me that he could not repair the system and some newspapers were stored. After that I tried to install win 8.1 running from a usb storage device that was the 8.1 software the installer of windows in it. Then the screen went black and I was promtped with "selected boot device failed." Press Enter to continue. "

  Any ideas on how to solve this problem?

  Problemi1 wrote:
  And now we're back to the original problem. I have an official version of windows 8.1 downloaded and formatted to a 8 GB USB by the official program from the official websites of microsoft. And just to clarify, it works with my pc. Now, when I try to start the installation in HP computer, it promots me with "selected boot device failed." Press ENTER to continue"and im the possibility of"boot manager"," Manager "start of the EFI file', who faced the same problem when I try to manually start the device and start"(yep 2 times). "»

  Hello

  Sorry to hear that.

  If you see boot and boot to the EFI file manager but nothing else, the USB is not detected.

  Please, perform the above steps

  s ' ensure that the 8.1 Win USB is intact and working

  -Secure Boot to disable and enable the Legacy mode

  -save changes and continue with the F9 mode.

  

  If it still does not respond, please take screenshots and join them in the next post.

  I hope this helps.

• HP Envy 15 t-as000: brand new HP Envy w / SSD: "Boot Device not found".

  Hello

  I have a brand new (less than 1 week) HP Envy 15 t-as000 w / a 256 GB SSD.  After the impeccable behavior for 1 week, the laptop can be started is no longer.  No boot device is detected.  If I try to run a diagnostic on the hard disk, the BIOS I was informed that it can not detect even a current hard drive (see image)

  I don't know what happened.  I'm very careful with my machines.  He has not been abandoned. It has not been dropped on, or taken any sort of somehow.  I just pressed the power button one day (yesterday) and I see this:

  

  Thanks for the tips. I followed your recommendations and sent the laptop to HP for replacement (I bought this unit directly to the output from the HP website).

  However, I am frustrated because after all taxes and transportation costs, I had to pay an additional amount of $10.  The total general of the replacement order was $739,79 against $730,90 for the original purchase.  Why am I penalized $ 10 ($8,89 to be exact) for a mistake that was not even my fault?

  Also, I had to pay $24,83 FedEx packaging to send the laptop back.  How was I supposed to know I should have brought the Moose with me to Seattle, WA in Ithaca, NY packaging because the SSD was going to fail in my college dorm?

  So in the end, my HP Envy $730,90 now goes to the identical replacement of cost unit $739,79 + packaging from FedEx $24,83 phone = $ 764,62.

  Bottom line: screw - up HP cost me $33,72!  Not the end of the world but still a ringing sound nice when you're not yet a career with a cushy salary of mickael elite.

• HP Pavillion 11-N028TU X 360: boot device error after upgrade to Windows 10

  Hello

  My laptop had been improved automatically to Windows 10 about 3 days ago. It was fine, but last night, he had a funny noise and stopped working suddenly. I restarted my laptop, but it has shown a pop-up notification:
  "not found - boot device please install an operating system on your hard drive.

  This morning, I took my laptop to the IT Help Desk at my University, but strangely I could start it and the connection to my windows without any error notification but it took like a usual (about 15 minutes).

  What should I do with my laptop? It seems to work normally now, but I fear that it will freeze again all of a sudden. By the way, anyone know if I can use my warranty to the United Kingdom if I bought my laptop in my home country?

  Thank you.

  HI @rose0521,

  Welcome to the HP Forums! I read your post and wanted to help.

  I understand that once your laptop cannot start with the error message "not found boot device" and now is recovered, but you want to confirm that there is no problem with the laptop.

  You can follow the document below to test the hardware of the laptop:

  HP Notebook PC - detection of hardware failures (Windows, 10, 8)

  If you want to contact HP support to check if the warranty covers service to the United Kingdom, please click http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html for more contact information.

  Please let me know if that solves the problem by marking this message as "accept as a Solution.  To simply say thank you, click the thumb upward below!   If you need more assistance let me know and I will gladly do everything I can to help. Thank you.

  Kind regards

• no boot device - aspire V5-572PG

  Hi all

  im am currently woking on a aspire v5-572PG POPs with a guest of blue that says "no boot device, press a button. When I check the bios hdd0, hdd1 all say there is no hard drive but when I start my windows recovery flash player 8, I see the C: drive and all of its contents from the command prompt. I tried a few guides on the repair of the efi and bcd with no joy. I ran chkdsk c:/x/r, which has detected an error and it fixes but still the same fault. to this im point ideas, suggestions are much appreciated.

  Thank you for your time.

  Yes, it should always appear in the BIOS, regardless the State of the format (assuming it has not failed).
  I suggested the Recovery Console (called ASO in Win8) simply because your USB has managed to find.
  What I don't understand is why the BIOS is not having reported the HARD drive. You could try reinstalling the HARD disk, just in case you have an intermittent connection.

• When I try to power to the top of our Dell computer, we get a black screen and the message "boot device available. Press button to try again. »

  Pressing enter does nothing, then it usually starts by pressing "ctrl-alt-delete."  The computer runs VERY slowly.  We have Windows XP and also just downloaded Safe Eyes software McAfee, but it was slow & have start questions for a while.  My son also downloads a lot of PS3 games, etc.  Who would have something to do with it so slow?  Is there something we can do to clean it ourselves instead of redoing it to Best Buy and pay $100?

  Hello

  Start are what problems you referring?

  Method 1: May be that the hard drive is not detected. Boot to the Bios Setup and make sure that the first boot device is defined as hard drive and also make sure that save you the settings and check what is happening.

  If your computer is not configured to boot from a DVD, see the documentation provided with your computer. You may need to change your computer's BIOS settings. For more information, see BIOS: frequently asked questions. For assistance, contact the manufacturer of your computer.

  Warning of the BIOS:

  BIOS change / oxide of additional metal (CMOS) semiconductor parameters incorrectly can causeserious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  Method 2: If you are able to boot to the desktop then try to perform the clean boot on the computer to resolve the performance issue.

  From your computer by using a minimal set of drivers and startup programs so that you can determine if a background program is interfering with your game or program. This type of boot is known as a "clean boot".

  Reference:

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  1. click on Startand then click run.

  2. type msconfigand click OK.

  The System Configuration Utility dialog box appears.

  3. click on the general tab, click Normal startup - load all services and device drivers and then click OK.

  4. When prompted, click on restart to restart the computer.

  The following articles could be useful.

  Slow PC? Optimize your computer for peak performance

  http://www.Microsoft.com/athome/Setup/optimize.aspx

  How to make a computer faster: 6 ways to speed up your PC

  http://www.Microsoft.com/atwork/maintenance/speed.aspx

• Pavilion g6-2006ax: no boot device after bios update

  I flashed the latest bios for my model to win 8 64-bit, and then when it restarted, it says no boot device, the bios detects no hard drive can boot from USB but when I try to format or repair it is detected no drive to do. I took battery cmos out and get out again but nothing. I also tested the hold down windows but with the b button and the power up and let go of all keys but the remaining blank screen bios recovery does not pop up. How to return to old bios?

  the laptop booted from the external hard drive, then I flashed the bios back to the old and it worked!

• DV7-4180us giving msg No. Boot Device or n, HDD, Win7 does not start.

  Well, I think I've reached the beginning of what may be a serious problem. I've been away for 9 months and my laptop had been stored in his bag all the time not used with the battery disconnected. I went 2 weeks ago and it had been fine until last Saturday. I started it upwards and once the logon screen Win7 and logging frozen inside, and the screen went black. I have it turned off and restarted, and then he came up with the error message "No. Boot Device" as if Win7 is no longer installed. I ran several virus scanners and they came back without anything, I'm sure that this is not a virus, I mean I have not yet downloaded something long because before my departure other than all of the updates, I missed. I tried to reset the BIOS to factory default and use PC tune-up AVG to fix all the errors, but I'm still having this issue.  Funny, it is sometimes the laptop runs and sometimes it won't so I think this load default Win7 will progressively get worse? Not really sure cause I'm not very technical with laptops.

  I tried to run the test drive in the BIOS when it does not load, but it is just like "No hard drive detected" every time, but it passes the test of memory.

  The reason why I'm here is to know what are my options to resolve this problem, so far the only thing that I can think of is to replace the HARD drive and reinstall Win7 but I want to make it as painless as possible, or see what others can suggest.

  I have no disc for reinstallation of Win7 or any similar to disks. My laptop is out of warranty. I know that I have the Local disk drive (c :)) and also the recovery disk (D :).)  My hard drive is a TOSHIBA MK6465GSX.

  Some of my questions are when I take off the Toshiba HDD that will of course remove the (C :) drive BUT it will also delete my recovery disk (D :)? * see link below for what players I have *)

  http://img255.imageshack.us/img255/315/compcx.PNG

  Should I replace the HARD drive I have to reinstall Win7 correct?

  Hello

  A safe and fast way is to clone your HARD drive when it is until running, it means you have the same OS, drivers, software. All you need is the same size or more (capacity) of HARD drive and cloning software. You can find some free cloning software in the following list:

  http://DownloadSquad.switched.com/2008/09/05/5-free-apps-to-clone-your-hard-drive/

  I hope this helps.