No display after the update of BIOS on Satelltie P100

Similar Questions

• Satellite A200 PSAE0E - no display after the update of the BIOS has not

  Hi all

  I have Toshiba A200 PSAE0E. I got the Vista OS to Xp.
  When I tried to upgrade the BIOS setting, the system frozed.

  I reformulated the system using the power button. There is no display on my screen when restarting.
  I tried to restart by pressing F1, F2, key to the House and even removed the battery for a while, until what there is no display on my screen.

  I even tried connection and an external monitor, but that also there is no display.
  At the moment I don't have any sort of recovery disk.

  I would be very happy if someone could help me.

  Hello

  To me, it seems that the BIOS update procedure has failed.
  For no apparent reason has frozen the system and you have interrupted the update procedure.

  According to mu ROM module (where the BIOS is stored) has not been flashed properly and this is the reason why you cannot start the laptop.

  In this case, you need the help of ASP I know, this really stupid s situation but I'm afraid there is no alternative to m.

  I think that the technician will try to flash the ROM module using a special BIOS and then the cell phone should start properly if all goes well. I'll keep my fingers crossed for you.

  Good luck

• Satellite A300-1ID - no display after the update of the BIOS

  HELLO GOOD EVENING,.

  I HAVE this TOSHIBA SATELLITE A300-1ID, as described above, happens them have BEEN updated THE BIOS AND everything to HIT PC turned off and there is no power were all CURRENT PIC BY me UNLESS I get TURN OFF AND NEVER HAD ANY IMAGE or EVEN RELIANT YEAR EXTERNAL SCREEN to.

  BUT IF YOU TURN on THE PC NORMALLY, THE COOLER STARTS AND IS FUNCTIONING NORMALLY, THE CD and DVD DRIVE AND HARD DRIVE AND THE LIGHTS have ACCESS, so DO NOT image on-screen, already tested RAM MEMORIES HAVE an OTHER TOSHIBA SATELLITE OF MY WIFE AND WORKS WELL, I despair A PC because I NEED TO WORK AND NOTHING to TALK WITH computer THAT TELL me WHAT COULD BE THE BIOS or graphics HIGH card.

  THANK YOU NOW AND WAIT FOR YOUR ANSWER

  Hello

  Seems that something was wrong during the update of the BIOS
  For me it s really amazing because something like that never happened to me and I have updated the BIOS very often

  What to say that you will need additional assistance of Toshiba ASP. I think that the ROM module must be flashed once more using a disc of crisis.

• Updates are always on display after the update successfully

  Updated for service pack 1 (KB929729) as of 07/05/09 and update for windows vista (KB937286) dated 6/30 both have been installed correctly but then reappeared on the new list of updats

  Hi liagray1,

  Thank you for using the Microsoft answers forum. Hope you do well apart from the problem of windows update.

  Here are some steps that may help you to install the updates successfully.
   
  Step 1: First remove the updates.
  To remove the updates, go to "Control Panel"-> "features/characteristics of the program. In the left pane, click on "view installed updates".
  -Put out two updates one by one, then uninstall them.
  -Restart the computer.
  -If you are not able to find the update at the stated location, tΘlΘcharger 'Windows install cleanup utility': http://support.microsoft.com/kb/290301. Install and run the tool. Remove the two updates of the list of all the programs installed on your computer. Quit the utility.
   
  Step 2: put the system in a clean boot State.
  To perform a clean boot.
  -Click 'Start'. Type "msconfig" in the search box of start.
  -Press enter and click "continue" when you are prompted to.
  -Check the box 'Selective startup'
  -Uncheck "Load Startup items".
  -Go to the services tab, click "hide all Microsoft services.
  -Now click on 'Disable All', ensuring that the "hide all Microsoft services" box is checked.
  -Click 'Ok' and then click 'restart'.
   
  Step 3: run the following commands in an elevated command prompt.
  To do this, click "Start" and type "cmd" in the box "Search". In the results area, right-click "cmd.exe" and then click "run as administrator". You will be asked to type the password for an administrator account. If you are the administrator or type the administrator password, click on "continue". Then, click on "continue". At the command prompt, type the following commands one by one and press ENTER after each command.
  -net stop wuauserv
  -net of stop bits
  -net stop cryptsvc
  -ren %windir%\SoftwareDistribution SoftwareDistribution.old
  -ren %Windir%\System32\catroot2 catroot2.old
  -net start wuauserv
  -net start bits
  -net start cryptsvc
  Exit command prompt and restart the computer.
  -Now, open the windows update console and search for available updates. Install the updates that are important and critical.
  -Follow the step 2 again and put the computer in 'Normal startup'
  -Restart the computer.
   
  Reply back and let us know if this helps.
   
  Kind regards
   
  Mauricette
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Problems with the display after the update of Windows

  Hi guys,.

  I have not installed or updated all programs on my computer for at least a few weeks, with the exception of Windows Update, so part of MS updates, nothing has changed in recent weeks.

  A few days ago, my computer (HP dm1 laptop computer) screen acted funny - I took a screenshot of what happens and posted here:

  http://DL.dropbox.com/u/1076277/desktop_problem.jpg - basically, the display is all messed up with repetition of lines, etc.

  At first I thought it could be a driver problem, but the drivers are ok and were not being updated - in fact, in addition to the usual updates, the only new was the new update now live.

  I did a system restore (restore a week) and everything seemed normal again - this problem is intermittent, but very frequent, but within a few hours of use, there is no problems - until I run Windows Update, and it all started again...

  Any suggestions as to what might be the cause of the problem and a solution? I don't really have the time now to keep stable each item in the update...

  Thanks for the help.

  Hello

  If you want to study, it will take time but you can find the offending update.

  First update all updates (redundant, uh?).

  Make a note of all of the updates (KB numbers, etc.).

  Restore and install the updates one by one and not simultaneously.

  This way you can find the update 'wrong' and later come to conclusions based on what it is supposed to fix.

  Carlos

• Words don't is not displayed after the update to iOS10

  Many songs in my library have incorporated the lyrics (that I added using the 'Words' of iTunes tab). I'm used to be able to see everything while listening to the songs on my iPod Touch by tapping the image "sleeve" of the song.

  After the iOS10, this method does no more work. The other method, new to iOS10 (a special menu item "Words") does not either, as I don't see this anywhere menu item for all of my songs containing words. (Someone said that this function only works for the songs in Apple's music.)

  What should I do to restore this feature? Return to 9.3.5 or wait until Apple condescending to people like me who want to be able to read the lyrics while listening to the songs and who do not want to subscribe to the Apple's music?

  Form the iOS 10 manual

  See the lyrics. Drag until you see words, and then press Show to see. Press Hide to hide.

• Satellite A210 PSAFGE - no display after the update of the BIOS

  Hello!!

  I have Toshiba A210 PSAFGE. I have download BIOS OS from Vista to Xp and flashing.
  When I tried to upgrade the BIOS setting, the system frozed.

  I reformulated the system using the power button.
  There is no display on my screen when restarting.
  I tried to restart by pressing F1, F2 and even removed the battery, adapter for a while, until what there is no display on my screen.

  I even tried connection and an external monitor, but that also there is no display.
  At the moment I don't have any sort of recovery disk.

  I would be very happy if someone could help me.

  Boyfriend... You should not have put off your system by updating the bios...

  Closest contact center toshiba to recover such problems...

  Sul

• After the update to OS 9.2.1 connection of my mini iPad with a VGA projector no longer works... Any clue?

  After the update to OS 9.2.1 connection of my mini iPad with a VGA projector no longer works... Any clue? Thank you

  Try resetting your device. This will not erase your data stored on that device.

  • Press and hold the sleep/wake button
  • Press and hold the Home button
  • Press and hold both buttons until the display turns off and on again with the Apple logo on the subject.

  Alternatively, you can go to settings - general - reset - Reset all settings

  If that doesn't work, restore your device to factory settings. Please note that this will delete the data on your device.

  Take a look this Apple Support article: use iTunes to restore the iPhone, iPad or iPod to factory settings - Apple Support.

• After the updates of windows, the computer stops responding with a black screen at startup of the system

  Original title: Windows XP does not start after the update, no error message

  Has made no changes to the system, but the last thing that happened was an update of Windows security on stop.

  Now when I boot, the BIOS p.o.s.t. shows good HDs, good DVD-Rom, RAM, but Windows never starts, goes just a black screen, HDs are not accessed.

  -F8 does nothing, can't use the last known good Config or Mode safe

  -Change boot order in the BIOS to boot from the Windows XP DVD, hoping to get the recovery console, but the same thing: black screen, no attempt to spin-up DVD or HDs.

  -Removal of mobo battery to reset the CMOS, no joy.

  -Checked and re checked all connections inside.

  -Stripped devices and added one at a time, no joy.

  -Traded-in an old video card in case it was difficult to generate the higher res gfx, no joy.

  I was construction/upgrade / repair my own PC for 3 decades and can usually solve the problem and fix it myself, but this one me completely baffled.

  Any suggestions?

  Hi Cougarific,

  We recommend that you repair your Windows installation in according to method 2 of this article and check the result.
  See computer stops responding with a black screen when you start Windows XP
  

  Note: When you perform a repair installation, it restores the current installation of Windows XP to the version on the installation DVD. This requires you to reinstall all updates that do not appear in this version of Windows XP disc.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Applications no longer work after the update of the game store!

  In my Xperia SP applications do not work after the update from the game store and shows 15 times in one minute, unfortunately "Skype/social life/mcafee/chrome, etc." has stopped working while triying to open it. This problem is started, because I updated my phone in 4.3 jelly bean.

  My phone is ok now...

  I contacted the sony Xperia care and suggested a repair.

  And after repairing its great and works without a problem...

  The solution is here...

  Dear Mr. Jab,

  Greetings from support Sony Xperia.

  We sincerely regret the inconvenience.

  We appreciate the importance of your concerns and we are here for you help.
  In response to the request of ypur, we would like to inform to run the reapair software.

  The enforcement procedure to repair your Windows computers using software and application of PC Companion:

  Note! You should always back up all data before you perform a repair of software.

  1. Download PC Companion to sony and install it on your Windows computer.
  2. Turn off the phone and disconnect the computer.
  3. Open the PC Companion application.
  4. Select start under the support area.
  5. Select the software update feature, and then start.
  6. Not found phone is displayed. Select phone repair and Connect.
  7. You will receive a message on PC companion, that data will be lost if you continue.
  8. Check the box to confirm that you have understood that all personal data will be lost. And then click Next. The application prepares the update and if necessary necessary downloads data on the web.
  9. Select your phone model manually, and then click Next.
  10. Depending on the model chosen, you will need to perform a few steps for the update for PC Companion be able to update the phone software.
  11. Yet, do not plug the phone! Note! At this point, the phone must be turned off and disconnected from the computer.
  12. Connect the USB cable to the computer, not on the phone.

  13.Xperia: then just pressed the button indicated, connect the USB cable for device theXperia and keep holding and pressing the indicated key until your device update started... appears (in some cases installation drivers appears first).

  1. If you have not correctly, do the phone turns on and proceed to the next steps, drag the bottom of the convening of the notification bar.
  2. In this case, disconnect the phone from the cable, turn it off and repeat step 12.
  3. Follow the instructions on the screen. Once the repair is completed, unplug the unit and then restart the device.
  4. Click on Next. If the repair was successful, the message this device has been updated successfully is displayed.
  5. Click Finish.

  Please contact the Support of Sony Xperia.

  Looking to better serve you.

  Kind regards.

• After the update of Cryptoprevent missing v7.0 the sidebar

  Hello

  I've just updated to v7.0 of the CryptoPrevent.

  After a reboot my sidebar with gadgets isn't available to retrieve.

  CryptoPrevent has the following: "the pane Windows and Desktop Gadgets are a major valunerability for security and Microsoft recommends deactivation. You want to keep disabled (recommended) Yes No

  I chose the 'no '.

  Following what CryptoPrevent asked to restart the computer and go with him... but the sidebar do not appear.

  I chose the DEFAULT Option: recommended for most people.

  There is little time without success.

  Someone else has the same situation after the update and is there a cure?

  Concerning

  Win 7 x 64 is my OS

  Snow,

  I don't have / use Sidebar/Gadgets, so I can't say anything definitive on this matter.

  Just a suggestion... since I'm not sure what the DEFAULT options will check beforehand, we will be absolutely sure through the ADVANCED interface:

  Open CryptoPrevent, click OK. Click the ADVANCED tab, select DISPLAY the ADVANCED OPTIONS.   In the left column, to halfway under various Protections, Acheck box for DISABLE WINDOWS SIDEBAR & GADGETS.   Then down to the right, click on the button of PROTECTION will APPLY.  Restart and see what happens.

  No guarantee it will make a difference, but it's worth a try.

• Mac stops do not after the update of the sierra

  I've updated my MacBook Air (13 inches early 2015) to Sierra. After the update, it is not shut down or restart. If I click on stop, my screen goes black and the keyboard backlight is on. The judgment never ends. Its the same case on reboot too.

  Help, please. Thank you.

  Although this will help, but I have also reported this problem, like many other people:

  MacBook Air shutdown correctly

  macOS Sierra presents a serious problem that must be dealt with quickly

  Apple should give a direct response to this because it is obviously not an isolated incident.

• unusual warm-up and drainage of battery fast after the update for sierra

  everyone knows unusual warm up their MacBook pro and the draining of battery faster after the update to Mac OS sierra?

  my MacBook 2015 mid pro gets hot when I close the screen and put it to sleep, as well as drainage of battery faster than usual. everyone knows the same?

  Try to use the activity monitor to see where will your battery life.

  1. go to the docking station
  2. Click on finder
  3. Click the menu go
  4. Choose utility
  5. Double-click activity monitor
  6. Click the stack tab

  See you using your battery?

• IPad no charging current after the update to IOS 10, when connected to the laptop.

  My Ipad no charging current after the update to IOS 10, when connected to the laptop. But fine load with Bank charger or battery with the same cable brightening.

  PL suggest how to overcome this problem.

  Have a look here If your iPhone, iPad or iPod touch won't charge - Apple Support

• Delete buttons do not work after the update of 10.11.16.

  Delete buttons do not work after the update of 10.11.16.  The delete button works if I pointed out and then delete, but not if I use the "back" button or try a removal of uniqueness.  It is a problem in all applications.  I tried it in textedit, search google chrome, safari search and find finder engine.  There seems to be a 'problem' of the keyboard' as far as I know nothing happened to my keyboard, IE the spilt coffee, that recent warming has been updated to 10.11.16.  I use an iMac (27-inch, late 2009) with i5 clocked at 2.66 GHz, running OS X El Capitan.

  Any suggestion would be appreciated.

  Greetings, r.fromstouffville!

  It seems that the 'Delete' on your iMac keyboard key works as it is supposed to be after update to OS X 10.11.6. I'll be happy to help you get these keys working again.

  Reset of the controller management system (SCM) on your Mac - sometimes it's a matter of simply resetting your iMac SMC. Open this article and scroll down to "Reset the SMC on Mac desktop" section and follow the steps there.

  Try safe mode if your Mac does not start -even if your iMac, safe mode startup make sure it starts successfully.

  How to test one question in another user on your Mac account - use this article if restarting in safe mode did not help.

  Use Time Machine to back up or restore your Mac - if your keyboard does not always work as it should, I recommend you save your iMac to ensure that your personal data are safe. It is always better "to have" a backup for a backup "need."

  On OS X Recovery - if you have reached this point, you encounter the same problem in a test user account, that would mean it is a system-w. Start your iMac into Recovery Mode and reinstall the operating system.

  Thank you for the communities of Apple Support!