No network access internal via QuickVPN

Similar Questions

• ASA VPN network access internal

  We have ASA5510s and I set up a VPN SSL using AnyConnect... The VPN address pool is 10.10.10.0/24 and our internal network is 10.10.20..0/24. After the connection successful, using LDAP. the customer receives an address 10.10.10.0/24 from the pool, but cannot access anything on the internal network 10.10.20.0/24. I played with access lists and NAT exemption, but nothing helped. What should I do?

  Good, happy, I can help you here.

• Cannot access internal network so AnyConnect SSL VPN, ASA 9.1 (6)

  Hello Cisco community support,

  I have a lab which consists of two virtual environments connected to a 3750-G switch that is connected to a 2901 router which is connected to an ASA 5512 - X which is connected to my ISP gateway. I configured SSL VPN using AnyConnect and can establish a VPN to the ASA from the outside but once connected, I can't access internal network resources or access the internet. My information network and ASA configuration is listed below. Thank you for any assistance you can offer.

  ISP network gateway: 10.1.10.0/24

  ASA to the router network: 10.1.40.0/30

  Pool DHCP VPN: 10.1.30.0/24

  Network of the range: 10.1.20.0/24

  Development network: 10.1.10.0/24

  : Saved
  :
  : Serial number: FCH18477CPT
  : Material: ASA5512, 4096 MB RAM, CPU Clarkdale 2793 MHz, 1 CPU (2 cores)
  :
  ASA 6,0000 Version 1
  !
  hostname ctcndasa01
  activate bcn1WtX5vuf3YzS3 encrypted password
  names of
  cnd-vpn-dhcp-pool 10.1.30.1 mask - 255.255.255.0 IP local pool 10.1.30.200
  !
  interface GigabitEthernet0/0
  nameif inside
  security-level 100
  IP 10.1.40.1 255.255.255.252
  !
  interface GigabitEthernet0/1
  nameif outside
  security-level 0
  address IP X.X.X.237 255.255.255.248
  !
  interface GigabitEthernet0/2
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/3
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/4
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface GigabitEthernet0/5
  Shutdown
  No nameif
  no level of security
  no ip address
  !
  interface Management0/0
  management only
  nameif management
  security-level 100
  IP 192.168.1.1 255.255.255.0
  !
  boot system Disk0: / asa916-1-smp - k8.bin
  boot system Disk0: / asa912-smp - k8.bin
  passive FTP mode
  permit same-security-traffic intra-interface
  network of the NETWORK_OBJ_10.1.30.0_24 object
  10.1.30.0 subnet 255.255.255.0
  network obj_any object
  network obj_10.1.40.0 object
  10.1.40.0 subnet 255.255.255.0
  network obj_10.1.30.0 object
  10.1.30.0 subnet 255.255.255.0
  outside_access_in list extended access permitted ip object NETWORK_OBJ_10.1.30.0_24 all
  FREE access-list extended ip 10.1.40.0 NAT allow 255.255.255.0 10.1.30.0 255.255.255.0
  access-list 101 extended allow any4 any4-answer icmp echo
  access-list standard split allow 10.1.40.0 255.255.255.0
  pager lines 24
  Enable logging
  asdm of logging of information
  Within 1500 MTU
  Outside 1500 MTU
  management of MTU 1500
  ICMP unreachable rate-limit 1 burst-size 1
  ICMP allow any inside
  ICMP allow all outside
  ASDM image disk0: / asdm - 743.bin
  don't allow no asdm history
  ARP timeout 14400
  no permit-nonconnected arp
  NAT (inside, outside) source obj_10.1.40.0 destination obj_10.1.40.0 static static obj_10.1.30.0 obj_10.1.30.0 non-proxy-arp-search to itinerary
  NAT (inside, outside) static source any any static destination NETWORK_OBJ_10.1.30.0_24 NETWORK_OBJ_10.1.30.0_24 non-proxy-arp-search to itinerary
  Access-group outside_access_in in interface outside
  !
  Router eigrp 1
  Network 10.1.10.0 255.255.255.0
  Network 10.1.20.0 255.255.255.0
  Network 10.1.30.0 255.255.255.0
  Network 10.1.40.0 255.255.255.252
  !
  Route outside 0.0.0.0 0.0.0.0 10.1.10.1 1
  Timeout xlate 03:00
  Pat-xlate timeout 0:00:30
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  without activating the user identity
  identity of the user by default-domain LOCAL
  Enable http server
  http 192.168.1.0 255.255.255.0 management
  http 192.168.1.0 255.255.255.0 inside
  http X.X.X.238 255.255.255.255 outside
  No snmp server location
  No snmp Server contact
  Crypto ipsec pmtu aging infinite - the security association
  Crypto ca trustpoint ASDM_Launcher_Access_TrustPoint_0
  registration auto
  full domain name no
  name of the object CN = 10.1.30.254, CN = ctcndasa01
  ASDM_LAUNCHER key pair
  Configure CRL
  trustpool crypto ca policy
  string encryption ca ASDM_Launcher_Access_TrustPoint_0 certificates
  certificate c902a155
  308201cd 30820136 a0030201 020204c 0d06092a 864886f7 0d 010105 9 02a 15530
  0500302b 31133011 06035504 03130 has 63 61736130 31311430 12060355 74636e64
  0403130 31302e31 2e33302e 32353430 1e170d31 35303731 32303530 3133315a b
  170d 3235 30373039 30353031 33315 has 30 2 b 311330 0403130a 11060355 6374636e
  64617361 30313114 30120603 55040313 0b31302e 312e3330 2e323534 30819f30
  0d06092a 864886f7 010101 05000381 8 d 0d 003081 89028181 00a47cfc 6b5f8b9e
  9b106ad6 857ec34c 01028f71 d35fb7b5 6a61ea33 569fefca 3791657f eeee91f2
  705ab2ea 09207c4f dfbbc18a 749b19ae d3ca8aa7 3370510b a5a96fd4 f9e06332
  4355 db1a4b88 475f96a1 318f7031 40668a4d afa44384 819d fa164c05 2e586ccc
  3ea59b78 5976f685 2abbdcf6 f3b448e5 30aa96a8 1ed4e178 0001300 020301 4 d d
  06092a 86 01010505 00038181 0093656f 639e138e 90b69e66 b50190fc 4886f70d
  42d9b4a8 11828da4 e0765d9c 52d84f8b 8e70747e e760de88 c43dc5eb 1808bd0f
  fd2230c1 53f68ea1 00f3e956 97eb313e 26cc49d7 25b927b5 43d8d3fa f212fcaf
  59eb8104 98e3a1d9 e05d3bcb 428cd7c6 61b530f5 fe193d15 ef8c7f08 37ad16f5
  d8966b50 917a88bb f4f30d82 6f8b58ba 61
  quit smoking
  Telnet timeout 5
  SSH stricthostkeycheck
  SSH timeout 5
  SSH group dh-Group1-sha1 key exchange
  Console timeout 0
  VPN-addr-assign local reuse / 360 time
  management of 192.168.1.2 - dhcpd address 192.168.1.254
  enable dhcpd management
  !
  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  Trust ASDM_Launcher_Access_TrustPoint_0 vpnlb-ip SSL-point
  SSL-trust outside ASDM_Launcher_Access_TrustPoint_0 point
  WebVPN
  allow outside
  AnyConnect image disk0:/anyconnect-linux-3.1.09013-k9.pkg 4
  AnyConnect image disk0:/anyconnect-macosx-i386-3.1.09013-k9.pkg 5
  AnyConnect image disk0:/anyconnect-win-3.1.09013-k9.pkg 6
  AnyConnect enable
  tunnel-group-list activate
  internal GroupPolicy_cnd-vpn group policy
  GroupPolicy_cnd-vpn group policy attributes
  WINS server no
  value of server DNS 8.8.8.8
  client ssl-VPN-tunnel-Protocol
  by default no
  xxxx GCOh1bma8K1tKZHa username encrypted password
  type tunnel-group cnd - vpn remote access
  tunnel-group global cnd-vpn-attributes
  address-cnd-vpn-dhcp-pool
  strategy-group-by default GroupPolicy_cnd-vpn
  tunnel-group cnd - vpn webvpn-attributes
  activation of the alias group cnd - vpn
  !
  ICMP-class class-map
  match default-inspection-traffic
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map icmp_policy
  icmp category
  inspect the icmp
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect esmtp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  Review the ip options
  inspect the icmp
  !
  global service-policy global_policy
  service-policy icmp_policy outside interface
  context of prompt hostname
  no remote anonymous reporting call
  Cryptochecksum:261228832f3b57983bcc2b4ed5a8a9d0
  : end
  ASDM image disk0: / asdm - 743.bin
  don't allow no asdm history

  Can you confirm that this is correct, your diagram shows your IP address public on ASA as 30 while you have assinged on 'outside' interface like 29?

• Xp virtual drive through network access

  I am running Windows 7 Professional and that you have installed a virtual Windows XP drive in order to run programs that are not able to run on Windows 7. When you open Windows Explorer, I see a list of my connections to the network. My virtual drive XP is in the list. However, when I try to access it via the browser, I get an error message that your computer has problems finding the connection. I am the administrator and the only user on the system. I'm the one who installed the virtual drive, and it has been used for more than 6 months. How can I access the virtual drive? I want to transfer files, and copy and paste them do not work. Please notify. Thank you.

  Hello

  I suggest you to send your request in the TechNet Forums to improve assistance in this regard.

  Here is the link: http://social.technet.microsoft.com/Forums/en-US/home?forum=w7itprovirt&filter=alltypes&sort=lastpostdesc

  Hope this information is useful.

• Problem of peripheral access NAS via the VPN Site to Site

  Hi all

  I am facing a strange problem with a client. I use a VPN from Site to Site between two ASA 5505 to connect its network to ours to replikate between a NAS on his side and a NAS on our side. I use the same configuration with other guests and it works fine.

  With this client, while I am able to ping the remote NAS and I have problems using SMB to connect via ssh (it works _sometimes_ but most of the time to access files via eplorer results in a timeout) and join the NAS Web portal (http and https, with https I can see the remote certificate of the SIN but the page does not load). These problems occur on both sides (our network-> NAS, customer network-> our NAS client)

  I can access the NAS even without any problems other customers. ASA newspaper I see no connection blocked or whatever it is when this happens and the tunnel seems to work fine otherwise.

  Any ideas how to refine the problem here?

  Thanks in advance

  Tobias

  It looks like you can run into problems with packets that are too big for your tunnel. Try to limit the size of TCP segment by putting the following on your ASA units:

   sysopt connection tcpmss 1360

  Most VPN tunnels are not going to have an MTU (Maximum Transmission Unit) less than 1400 bytes, so the above should clean things up.

• Deactivate the filter driver Cisco AnyConnect Network Access Manager

  I hope that it is the community just to post this in.

  I was wondering if it is possible to script disable the "Cisco AnyConnect Network Access Manager filter driver" for a LAN connection?

  By comparison to the registry before and after it is manually turned off via Control Panel control-> network and Internet-> network-> connection to the Local network connections, I came with:

  : remove the filter Cisco AnyConnect Network Access Manager driver
  : the list of filters for the LAN adapter
  reg delete HKLM\SYSTEM\CurrentControlSet\Control\Class\ {4D36E972-E325-11CE-BFC1-08002BE10318} \0007\Linkage /v FilterList/f

  : import the Cisco AnyConnect Network Access Manager filter driver
  : to the list of filters, excluding the LAN adapter
  Reg import linkage - no - lan.reg

  : remove the filter Cisco AnyConnect Network Access Manager driver
  : the network of the LAN adapter config
  reg delete HKLM\SYSTEM\CurrentControlSet\Control\Network /v /f Config

  : import the Cisco AnyConnect Network Access Manager filter driver
  : to the network with the exception of the LAN adapter config
  Reg import network - no - lan.reg

  : Remove the adapter LAN of the list of maps where the
  : Cisco AnyConnect Network Access Manager filter driver is used
  reg delete HKLM\SYSTEM\CurrentControlSet\services\acnamfd\Parameters\Adapters\ {77197E43-5875-469F-A3A5-A97F63A32E0A} /f

  This disables 'Cisco AnyConnect Network Access Manager filter driver' to connect to the local network, but it is not automatically to my wireless connection.  However, if I manually in a not checked the "Cisco AnyConnect Network Access Manager Filter Driver', the connection automatically changes my wireless.

  The end result, I'm looking for must be able to use a wireless connection and at the same time be able to use the connection to the local network, when I connect directly to some work equipment to download the firmware files.

  Any thoughts would be greatly appreciated.

  Thank you.

  Hi Paul,.

  Instead of hacking the registry, you can use nvspbind.exe for this task.  You can download the tool here.  It will be also NAM automatically mode interfaces.

  https://Gallery.technet.Microsoft.com/Hyper-V-network-VSP-bind-cf937850

  Disable: nvspbind.exe /d "Wireless network connection" csco_acnamfd

  activate: nvspbind.exe/e 'Wireless network connection' csco_acnamfd

  Thank you.

• No access internal Horizon 6

  Hello

  I had to do a restore our connection and security from a veeam backup servers. They have restored and are accessible remotely, but now we have no access to the Horizon internally via the Security server. All settings seem identical, but it does not seem to connect. I thought it could be a DNS issue, but all settings seem fine and stable via IP also fails.

  Thank you

  The problem was with the firewall. I had just done an update, I spent in the version of the patch and everything works fine now.

• popular error; An error occurred when opening a virtual disk. Make sure that the converter server and source running machines have network access to the ESX/ESXi hosts source and destination.

  Once again; same problem, others have encountered but nothing seems to work.

  An error occurred when opening a virtual disk. Make sure that the converter server and source running machines have network access to the ESX/ESXi hosts source and destination.

  We have 1 physical servers, we need to see. Here is the environment. All 3 separated location, 3 all firewall separated

  1 physical servers

  -Internal IP address; 172.16.160.21
  -FARM Firewall

  vCenter Server

  -Internal IP address; 172.16.1.85

  -Local Office (ALX)

  Location of destination (ESXi host):

  -Internal IP address; 172.16.153.20

  -Firewall ROOMMATE

  
  Already completed:

  VMware KB: disable SSL on VMware Converter Standalone 5.x encryption   SSL disabled in converter-worker

  Firewall are open / Tunnel is open throughout the environment.

  I have attached the logs.

  Thank you very much

  POCEH; Thanks for the reply. But I wouldn't be pulling my gray hair if I knew what the problem was. I understand that there not for the peer but why...?

• Toshiba NB520 11V - how to install a 3G network access module

  Hello

  I recently bought a NB520 11V and I was interested if it's possible and how to install a module 3G network access. And if it is possible, what are the specifications of the installation of a 3G network access module I have to buy.

  Kind regards
  Luis

  Hello

  As I know that some of the model supports NB500 is the 3G module but the NB520 does not support 3G.

  The 3 G CARD-F3307R2 (900TEG), which is equipped in the NB500 is the number of piece K000124470 (google for it)
  But to be honest I'm not very well if this module is compatible with the Mr. NB520 I guess not

• Property of local network access

  After installing SP2

  insufficient right SP2 to the ownership of network access

  Hello

  I put t see no problem why Windows XP with SP2 should t works on the Satellite Pro. The Microsoft SP2 includes a large number of bug fixes. In addition the SP2 installs a windows firewall that must be enabled on your device. But that innovation is compatible with all laptops from Toshiba. Like Quad please visit Microsoft site to find an SP2 information.

  PS: It would be great if you will write about your unit name and problems with your device.

  Good bye

• Can I access wifi via my cell connection on my iPhone 6 if there is no available wireless system? My husband Samsung cell phone can access wifi via cellular connection.

  Can I access wifi via my iPhone 6 s cellular system? My husband Samsung cell phone can do that when no wifi system is obvious.

  I need to change the above question. How can I connect Internet through my cell system if no wifi is available? Thank you.

• In Windows 8 network access protection

  How can I activate on the network access Protection in Windows 8?

  Driley25,

  I understand that you must enable the network access protection feature in windows 8.

  Steps below:

  1. on the screen type Windows apps services.

  2. on the right, click settings

  3. on the left side, click local services.

  4. the PC will put you on the generic desktop and you will see the box.

  5. on the right to scroll down, the ads are in alphabetical order so just head to section N and should see.

  Please answer as soon as possible.

  Thank you

• I have an iPhone and a MacBook Air 11 '' 6. iPhone 6 syncs and backup icloud. I can access iCloud via the net on MacBook.  The problem is that I can't get the MacBook to sync with iCloud.  How can I do this?  Help, please. Thank you.

  I have an iPhone and a MacBook Air 11 '' 6. iPhone 6 syncs and backup icloud. I can access iCloud via the net on MacBook.  The problem is, I can't get the MacBook to sync with iCloud.  How can I do this?  Help, please. Thank you.

  What, in particular, looking to sync with the Mac iCloud? If you mean things like Contacts, calendars, Notes, etc., then you want to go in under the  system preferences, click the iCloud and connect to iCloud there with your iCloud ID. Then select which items you want to sync'd via iCloud.

  What - what are you trying to do?

  See you soon,.

  GB

• Pavilion laptop g6: Network Access Protection

  I have a laptop HP pavilion g6 & my security keeps warning me that my network access protection is turned off & when I click on it - it does nothing it does it - what is the network access Protection & how I turn it on?

  Hi robindt,

  Same thing here.

• Network access: is it let me connect but a yellow explanation mark appears who says no access to the network

  sound to connect me but a yellow explanation mark appears who says no network access why is it?

  See if there is something in there that helps:-

  http://www.ComputerActive.co.UK/CA/PC-help/2033224/network-solved

  If there is, please voet as useful.

  Thank you.