No power and flashes of light every ten seconds

Similar Questions

• Lock screen and mouse L850 satellite every 2 seconds

  I think I have a hardware problem with the Satellite PSKDLA - 0C800R L850.

  It is a laptop I bougth to my wife but he has ended up with my stepson of Uni studies. While he had it the hard drive is not one of his friends replaced. twelve months later, he advised it was gone blackscreen and G'nort would turn out.

  I finally got hold of it again and managed to drain the power remaining and replaced the CMOS battery remove a strip of RAM and it starts fine. I've proved a faulty stick so that left aside. Then I realized that there was a problem with the screen and the mouse

  . The screen would brighten up (wash out) then Flash and stabilize. First thought was video chip or the driver.
  At the same time would lock the mouse. When the screen clears the mouse would again.
  Happening every three or four seconds but now every two seconds. It is more difficult to do something.

  Have reloaded many drivers, but I think it is material, but not sure if it needs a motherboard or processor.
  Can you advise?

  I forgot to mention that the image of the screen is slightly down from senior management.
  Tere is a few millimeters of black with a white line on the top edge of the image.
  This white line seems to come on and off with the locked mouse synchronization and the screen. This is another indication of the problem or the backlight?

  Hi, have you checked the thermal paste between the CPU and the heatsink?
  CPU fan blows hot air outdoors?

• Lenovo 3000 N200 on the habit of power and shows no lights

  Hi all

  I have a Lenovo 3000 N200 laptop. One day he just off its autonomy while watching a video, and now shows no signs of life. Used to power on, no light when it is connected with a power supply, nothing.

  I tested the power supply and tried another new and get the same result. So I don't think that the battery/power supply is the issue.

  I have a feeling that it is something more serious, the laptop is out of warranty and IBMs fresh out of warranty are stupidly high. If anyone knows what could cause this problem and if it is possible to repair with a spare room (off ebay or elsewhere), I'm able to disassemble the laptop and replace a part.

  Thanks for any advice.

  Bass sounds.

  Some say remove memory and see if it gives an indication

  of life, like any beeps at startup.

  Try without battery, try to unplug it, remove the battery and press and hold the

  power button for 30 seconds and plug in again etc.

  Try to remove the hard drive, but this looks like a dead motherboard

  If you have any sign of life after trying everything you can think of.

• KDL55HX800 turns off and back on again in standby mode every 15 seconds.

  KDL55HX800 constantly turns off the coast and return to sleep every 15 seconds. Also, when I first turn on it will power itself and turn it back on. It is connected to the Internet and has the latest software update (PKG4.114AAT). Any help is appreciated.

  I ask for the service... or by e-mail at sony support usa at [email protected] with all your details (series number, model, name of the contact info)

• Distortion of the sound every 20 seconds on Satellite C

  When listening to audio with and without a helmet, every 20 seconds or so the output sound is deformed for several seconds and in some cases this sound distortion also causes computer to freeze completely display.

  My PC is a Toshiba Satellite series C running Windows 7.

  Any suggestions please?

  Please be so kind and post some info about this noise problem.
  Are you using the original pre-installed OS that you got with your laptop?
  Have you noticed this problem on the first day?
  Have you noticed this problem whenever you hear the music and watch movies using different actors?
  With other words, it's a kind of general problem on your laptop?

  When this happens you noticed most high HDD activity in the background (System analysis, installation of updates or something similar)?

• First Pro CC 7.1 playback jerky every 12 seconds

  Hello

  I have a strange problem. I'm reading 1080 p/23.976 images MXF on a timeline of format MXF 1080 p/23.976 (same), and the video stutters every 12 seconds. It manifests itself as a kind of déjà vu, where a small section of 5 images maybe seems to play twice. During the audio continues perfectly, and I perfect lip-sync overall. So I think that what is happening is that PP is falling 5 frames and then playing twice the next 5 images. Otherwise, I can't explain why it keeps Lip-Sync, and the audio plays continuously at the proper height. It's like a strange artifact of time repeating that would be a plot point in Star Trek.

  The problem is not in the video file itself - if I play again, it happens somewhere else, and he does not appear in the export. It's strictly reading.

  My system is extremely strong, Core i7, 48 GB of RAM, at least a rate 100 MB/s since the RAID. There is nothing to see on the chart of the CPU during the stuttering. I have also problems of video playback on the computer. It is only in pages.

  I tried to go to mercury CUDA vs CPU, and it makes no difference. Sometimes I play a clip in the source monitor or timeline. Happens if I am video mirroring. It happens regardless of which is the resolution of reading. Happens no matter what codec is the film. It happens with MXF, MPEG and MP4.

  More important still, the indicator dropped done frame * not * detect that it happens.

  It is certainly possible to keep uninstalling things to know if maybe something is interacting with PP in a bad way, it's very destructive on a working system, and I want to hear if someone has experienced something similar.

  Any help would be appreciated.

  Thank you

  By

  Hello

  I solved it, and I will post the solution here for someone else. This has to do with the Turbo mode on the Core i7 processor.

  I noticed that the jump happened during a period of no video on the timeline, and I saw that the playhead to literally jumped back, led me to conclude that it had nothing to do with the GPU, but that he was bound to the time base. I searched in the Adobe forums for a reading jump head-related positions and found a guy who said the Turbo mode on the Core processor i7 mess with time from first base, and the jump of the read head is a correction for it.

  Normal high performance and video mode switch is completely smooth.

  Thank God I do not go out and buy new maps video and ripped the computer and clean installs as suggested. But it's pure luck, that would have been my next step.

  Thanks, Guy!

  By

• Qosmio X 500 does not start and the power LED is flashing every 5 seconds

  Hello
  I need help my X 500 does not start now. I tried to launch the NB as usual and suddenly the X 500 start or even power up.

  If I press the power button / stop it makes no noise, the power LED on the button and the second power LED just bliks once and turns on and keep blinking every 5 seconds.

  I tried to:
  * Remove battery and power up with AC only
  * power only to batteries
  * remove the battery power button hold for 30 seconds and over power with AC, battery only athen

  but it did not help.

  I checked the LEDs AC & battery, but they do not blink, they are just RED, so there is no problem in battery or AC.

  No idea where could be the problem?

  Thanks for help
  Frantisek

  Hello

  The failure of RAM could be the reason for this behavior of the laptop.
  Remove the RAM modules with good modules tested and check the functionality of the laptop.
  In the case of RAM isn t the troublemaker, the motherboard could be affected.

  Good luck and share your experience with us.

• Tecra S2 - power and battery LED flashes - no start

  G ' Day at all.

  I have a TECRA S2 under XP SP3.
  Everything was fine until I went to a place of friends with her and plugged into the power supply and it lights up not at all and no LED.

  I removed the battery and then tried again and then happen to the power and battery LED flash together, but nothing else.

  Tried several times with the battery inside and out with the same results.
  I have stabilize power before removing or installing battery.

  Do not even have BIOS or a screen. I put the HARD drive in a caddy, and it's accessible.
  See you soon
  kb3500

  > Everything was going well until I went to a place of friends with her and plugged to the power
  Did you use the right adapter?

  To be honest, it looks like a malfunction of the power supply motherboard maybe electronic issue of power.
  the power indicator would start flashing amber if the AC adapter voltage is abnormal or failure of computer power supply.

• Paviliion g7: low-light battery charger and flashing

  My HP Pavilion laptop g7 has a low battery and a flashing white light on the charger.  What should I do?

  Hi there @MizDeb15

  Welcome to the Forums of HP Support! It's a good place to find the help you need, so many other users, the HP experts and other members of the support staff.

  I understand that you have supply problems, and I'm happy to help you. Please report the number of complete product for your laptop. Check out the following, if you need assistance with this information.
  How can I find my model number or product number?

  Try to work through the following pages, that something can help, or at worst, to isolate the problem.

  Computer won't start (Windows 7, Vista, XP)

  Using and testing the power adapter AC
  Improve the performance of the battery (8, 7, Windows Vista)

  HP laptops - test and calibrate the battery (Windows 7)

  Let me know how it goes for you and changes or errors, you see.

• HP 6940 power, resume, right cartridge lights flashing continuously

  I found my 6940 HP with power, which takes up and fires right cartridge like crazy. I did everything that I could Google to try to resolve the problem, several times in the course:

  • Power cycle, including remove the power cable from the plug
  • factory reset (report, press Cancel x 3
  • Remove/replace cartridges
  • move the rear cart & more
  • start without installed black cartridge
  • start without installed color cartridge
  • start without any cartridges installed
  • Check and check for paper jams (he was never that I can tell)

  In each case, my method was.

  • Remove the power plug from the back, wait 15 seconds to replace.
  • Try something from the above list

  In each case, the printer works fine for a few minutes. It's the ping requests, it is accessible via the integrated web page and a test page can be the printer. In each case, after a few minutes, the lights flash, and the printer is no longer pings or via the web page. When the lid is raised, the bar that prevents the cartridges come off, is stuck in the up position (preventing removal).

  I'm afraid that the thing bought the farm, but I've always been happy with it and will not replace it (all they seem to do today are these monstrosities multi-function) if there's a chance someone knows something that can fix.

  Darryl Hello,

  I noticed your post about your problem with your Deskjet 6940 showing you lights flashing lights and working for a few minutes at a time before the return of the cycle. I want to help you as best I can. I see that you already have some troubleshooting.

  I have studied this issue and have found some documents of troubleshooting I recommend search and try anything you have not yet tried.

  Flashing lights

  Transport is stuck

  Please see "Solution 2: clean the cartridge contacts.

  I really hope that this help solve you the problem, if there is anything else I can help with that feel free to respond!

  Kind regards

• BlackBerry 8900 smartphones will be no more power up and a red light blinks!

  I have a new 8900 and put in place all OK.  It now will not power and all I have is the red light flashes intermittently. Have tried removing the battery but no joy.

  Someone at - it ideas please?

  If your BlackBerry is still under tension turned off with a black screen, follow the instructions below. The only indication of life may be the flashing red indicator light in the upper corner. Nothing seems to wake and Desktop Manager does not recognize that a device is connected.

  (1) make sure that you have Blackberry Desktop Manager installed.
  http://NA.BlackBerry.com/eng/services/desktop/
  (2) on your PC, go to start > run and copy and paste the following line exactly (i.e. with quotation marks):

  'c:\program files\common research in motion\apploader\loader.exe' /nojvm

  (3) the Application Loader Wizard will appear - click on "next".
  (4) in the ' connection: ' drop-down menu, you should see "USB - PIN: UNKNOWN". Click on the button "next".
  (5) you should see a list of applications ready to be installed for your Blackberry. Press Next and finish, and that you are well on your way to get your Blackberry to life.  Just unplug and let the process finish completely.

  NOTE: If you do not display the list of applications mentioned in step 5 and instead to see the message "the Blackberry Desktop Software has no Blackberry Device Software for the device you have connected to the computer. Contact your wireless service provider or system administrator', then you must download the Blackberry operating system for your support and your device.
  http://www.BlackBerryFAQ.com/index.php/BlackBerry_Operating_System_Downloads
  Just select the appropriate type of carrier and network, select your Blackberry model from the list and download the latest version. Install this download and follow the steps above again and you should be on the right track.

• Compaq presario cq61: PROBLEM STARTING WITH PRESARIO CQ61... CAPS AND NUM LOCK FLASHES every 4 seconds!

  Hello! I have a problem with the starter. When I try to boot my laptop, my screen is black and Maj CapsLock and numlock just Flash every 4 seconds. Then I go to your page to download the BIOS. Well, when I dl and install Recovery BIOS for Compaq Presario CQ61-420EM get some InsydeFlash application, what is it for? I saw in the video that you get HP system BIOS update utility tool and that is the problem for me, I don't understand this application, instead, I get this "InsydeFlash" I don't know what is! HELP PLEASE!

  Hi @patrik13,

  Thank you for the update and confirmation.

  You would be kind enough to mark the post that solved your problem as accepted solution to help others who may have the same experience as you.

  Thanks in advance.

  Good luck with the repairs.

• DeskJet f4180: always E error message and empty cartridge light flashing after installing new cartridge

  I always get the error message E and empty flashing cartridge light after installing new black cartridge.

  Welcome to the @vinylzappaforum!

  I read on the 'E' and the empty cartridge light blinks after I installed a new black ink cartridge. If you have tried the guides that I suggested in our other thread here, so the next step would be to call phone support at HP to discuss your printer options coming with them. I let the info below.

  Please click the "accept as Solution" if we reached a solution and the "thumbs up" to say thank you for my help.

  Contact HP:
  Step 1. Open the link: www.hp.com/contacthp/
  Step 2. Enter the product number or select Auto detection
  Step 3. Scroll up to "still need help? Fill out the form to select your contact options.
  Step 4. Scroll down and click on: contact HP options - click Get phone number
  File number and phone number appear

• HP mini 1109tu does not illuminate and has its power led flashing

  Well I just got my Bill Mini of the day the following day and while they were inspecting it this morning the power led flashes and it won't turn (even on the battery mode).

  [IMG] http://i168.Photobucket.com/albums/u171/Arnaehl/img_96221_hp-1000.jpg [LINE]

  Will or may someone help me solve this. I can't bear to look at my dead minis.

  Thanks in advance.

  HP mini 1109tu

  Hello

  Arnaehl wrote:

  Well I just got my Bill Mini of the day the following day and while they were inspecting it this morning the power led flashes and it won't turn (even on the battery mode).

  [IMG] http://i168.Photobucket.com/albums/u171/Arnaehl/img_96221_hp-1000.jpg [LINE]

  Will or may someone help me solve this. I can't bear to look at my dead minis.

  Thanks in advance.

  Try a hard reset.

  Disconnect the electric plug. Remove the battery.

  Press and hold the power button for 15 seconds.

  release the power button.

  Plug the AC adapter.

  Press the power button.

  Best regards
  ERICO

• the G7 1113eo lights. Power led flashes 3 times pls help

  Hello, im hoping someone can help me, I have a 1113eo of the g7. that does not start. the battery has been dead for a while, but his works well with just the adapter. But yesterday it no longer starts, I tried to do the hard reset (remove battery and hold the power button for 15/30secs) but who did not work, so I started to disassemble that he virtually stopped when I discovered that I didn't have a screwdriver. then press the button power again just to check, and the pc started. a stroke of luck was good cause I tried to restart and it started again.

  whenever I press the power button, the little led next to the power supply, flashes 3 times. No its or other led´s flashing

  Please help me

  (ps the warranty is no longer valid)

  Hello

  It is certainly not good if you are able to check the adapter - my main concern, as you was able to get the laptop to start only once, is that this may also indicate a possible problem with the power supply Board.

  Kind regards

  DP - K