No sound from the Clip when it is connected to the car charger and car s in the

I just got a car charger for my 8 GB Clip. I have the Clip connected to the connector of the car aux in, and it plays beautifully this way.

However, when I connect the car charger, which is a fact by Motorola for a mobile phone, the sound of the Clip completely stops.  There is no sound at all.

Even if I barely touch the metal of the car charger USB plug to the USB port of the clamp, the sound cuts.

A ground loop isolator would correct this problem? The comments that I have read of these say all that they helped with motor and alternator noise, but I don't have that.  I have no sound at all, even if the Clip is loaded and he continues to play according to the display of the item.

I checked the car charger works well because I have a box of jump with a record of 12 VDC (just like in the car).  The cool Clip and plays with a helmet with the Motorola car charger in this configuration very well.

Any ideas what is wrong and how to fix it?

Thanks in advance.

Just for this follow-up, the ground loop isolator completely fixed the problem I had with the sound cutting on my video in the car.

The one I chose was the PAC SNI-1/3.5 RCA noise filter.  He goes online with 3.5 mm cable to the and has a socket on one end and a plug on the other.  It would have been cool if he had just had two male connectors, because then I could have plugged one side in the Clip and the other in the input of the car Jack.

There is no significant deterioration in the sound, and now I can load the Clip while listening.

Tags: SanDisk Sansa

Similar Questions

  • 550-215na Pavilion: no sound from the rear audio input jack

    Hello

    I recently bought a new PC and I immediately ran into an audio problem that I can't understand. I get no sound at all from the rear audio input jack. I'm getting sound before making, and the plug rear mic works. When I plug something into the rear socket, a message appears grateful that there is something. When I checked the sound settings while it is plugged into the rear outlet, the equalizer is moving, which indicates that he gets his. But nothing comes out when I plug headphones or speakers in. I can exclude a fault with the speakers and the headphones, because they work very well to come forward. All the drivers are up to date.

    Any help would be greatly appreciated!

    Hi there @PrimoFigs,

    I hope you find your experience of positive Support Forum! It's a good place to find the help you need, other users, the HP experts and other members of the support staff. I understand that you get no sound from your speakers when connected to the rear audio ports. I'm happy to give you a helping hand with this.

    Have you tried to connect another device to this port, whether it of a different set of speakers or earphones, headphones just to test if one of them works?

    What it is connected to the front port at the same time? If so, then disconnect this device and try again the rear port and let me know if there is a change.

    Also try this: desktop HP-no sound on speakers (Windows 8).

    Please let me know if any of the work of tip for you suggestions and if we don't solve your problem, please mark this message as a solution. Bravo would be appreciated as well.

  • No sound from the tv with hdmi w3 connection

    I have a standard micro HDMI to connect my w3 to tv.  When a movie plays on the w3, I can see the video on the Tablet and the tv, but only the Tablet has its.  Is this normal?   I checked that the tv properly with other hdmi sources works but have no way to test the brand new microphone cable or w3 drivers.

    I was unable to locate a compatible driver on intel.com.

    However, I tried the w3 with a different TV and everything worked as expected: even with only a 'driver' Intel ESS Audio Device (WDM) available.  Passage of the tablet on television was automatic.  I did plug in and turn on the tablet in front of the TV and everything worked.

    I tried the same procedure with the original tv and the results were good video but no sound from the TV.  The sound remained with the tablet.

    I hae 2 TVs and 2 blueray players.  I swapped every combination of TV and player and everything works well.  Since the Tablet works well with at least one TV, the hdmi cable is ok.  My conclusion is that the current configuration of the Tablet works with some TVs and others not, and until I can find a better driver I'll just have to live with it.  I wanted to be able to watch videos with the Tablet when I traveled and will just have to wait until I get whenever I go to see if it works.  Not very desirable but it's like that.

    Thanks for your suggestions and help.

    Problem solved (sorta).

  • No sound from the right speaker / can not configure the speakers

    Hi all

    I have a new computer Sony laptop and just tried plugging in my speakers 2.1 computer inside.  Sound only comes out of the left satellite and a subwoofer.  When I try to set them up in the sound control panel, the installation of the single speaker on the speaker Assistant is stereo and only the first test tone (left) plays from the satellite on the left, then silence (no dial tone test on the right).

    Everything works fine on the built-in Laptop speakers, but they are for computer speakers, so I wish I could use my old speakers when I'm at my desk.

    Sony Vaio and Windows Update Update did not recommend all new drivers for the audio controller.  I downloaded and installed the latest driver on the site from Realtek but that didn't work at all so I rolled it back to the version provided with the system.

    Work fine with my laptop speakers older and my cell phone, so the fault is not with the right satellite is.

    Thank you
    Drew

    Hi Drew,

    Thanks for posting your query in the Microsoft Community. There is no sound from the right speaker in accordance with the description of the problem.

    ·         Did you do changes on the laptop before the show?

    I suggest you follow the steps in the article.

    Tips for solving common audio problems

    You can see these articles for more information:

    Sound cards: frequently asked questions

    No sound in Windows

    I hope this helps. Let us know if you need more assistance.

  • iOS 10 no sound from the speaker of the ear or EarPods

    After update of iOS 10 (in 6 s iPhone and 5s) I have a problem then to make or receive calls. Most of the time it is no sound from the speaker of the ear or EarPods and I have to press the speaker during calls to listening. To get back what I have my iPhone and open it again. This seems to happen after that I used once the EarPods.

    Be aware that I have consume EarPods in 90% of my calls and iOS 9 I had no problem at all.

    Hello Billy78GR,

    Thank you for using communities of Apple Support. It is my understanding that you met the receiver and headphone audio problems after update to iOS 10. I know that it is extremely important to be able to hear others during calls. I'm happy to help you to get this resolved with you.

    First of all, I recommend you restart. This can solve many unexpected behaviours. Follow the steps below to restart.

    1. Press and hold the sleep/wake button until the Red slider appears.
    2. Drag the slider to turn off your device completely off.
    3. Once the device turns off, press and hold the sleep/wake button again until you see the Apple logo.

    Restart your iPhone, iPad or iPod touch

    As you use the headphones on most of your calls, I recommend checking and removal of dust or debris from the helmet. If the problem persists, please refer to the additional steps in the link below.
    If you do not hear a person, a call or a voice message or if the sound is not clear on your iPhone

    Have a great day!

  • New iPhone SE no sound from the speaker of the brand

    I just bought a new iPhone SE and I'm getting no sound from the speaker. Does anyone have any ideas on a possible resolution?

    I restored from an iPhone 5 to the top, both phones are on the latest version of iOS.

    Once the synchronization is complete, I ejected the phone correctly. But there is no sound coming from the speaker:

    • Key "secret" in both positions, no sound from the speaker
    • The top volume, using the volume buttons and the sound, no sound from the speaker settings
    • Headset plugged in, sound comes from the helmet, remove them, the iPhone recognizes, but still no sound
    • I tried the music app, ringtone from another phone, videos, podcast app, no sound from the speaker
    • Past the phone power off & on again, no sound speaker
    • Reset iPhone (hold both buttons down for 10 seconds), no speaker sound
    • Reset iPhone settings, no speaker sound

    I begin to suspect it is a hardware problem, but as I am not near the Apple Store, I would try as much as I can before you go this route.

    Thank you

    Hello Andy,

    Thank you for using communities of Apple Support.

    I understand that you have restored your iPhone backup iPhone a precedent, and now there is no sound from the speaker.  Given the troubleshooting you have already done your next step is to restore the factory settings to see if the problem persists:

    Use iTunes on your Mac or PC to restore your iPhone, iPad or iPod to factory settings

    If the problem persists, then please make an appointment with the Apple Store is close.

    http://www.Apple.com/retail/Geniusbar/

    Take care.

  • I have no sound from the external speaker

    I connected this morning my iPod in my car, as always. But today I got the only sound from the internal speaker and no sound from the external speaker in the car. So far I have never had problems.

    How did the car system connected to the car?

  • My speakers on my Dell Latitude D820 suddenly emit only a low sound. I adjusted all the volume controls in the menu sounds from the Control Panel, and there is no change in volume.

    Low sound volume

    My speakers on my Dell Latitude D820 suddenly emit only a low sound. I adjusted all the volume controls in the menu sounds from the Control Panel, and there is no change in volume. It's real power radio on the internet and play music from a CD inserted into my machine. The sound icon does not appear in the toolbar.  I tried the fixit of automatic Wndows and it ran and said low volume has been set. Not the case.

    Hello

    1. what operating system do you use?

    2 did you change on your computer?

    Method 1:

    I suggest you follow the link and check.

    No sound in Windows

    http://Windows.Microsoft.com/en-us/Windows/help/no-sound-in-Windows?T1=tab02

    Method 2:

    I suggest to follow the link and search for the volume in the taskbar.

    (a) right click on an empty area of the taskbar and then click Properties.

    (b) in the Notification area, click Customize.

    (c) select the volume see the icons and taskbar notifications check box, and then click OK.

    I also suggest you to follow the link and check.

    Change icons appear in the notification area

    http://Windows.Microsoft.com/en-us/Windows7/change-how-icons-appear-in-the-notification-area

  • Sound does not work when it is connected to the TV with HDMI

    I have a HP Pavilion Notebook PC, DV7 - 6813EV, running windows 7 Home Premium 64-bit SP1. My problem is that I have no sound when connected to my TV HDMI connection and press. Please could someone help me? Thanks in advance

    Hello gematz,

    The sound does not work when it is connected to the TV via HDMI.

    Go to start.

    Type sound.

    Click sound

    On the playback tab, click with the right button on the HDMI interface, and then select set as default device.

    If you do not see the HDMI, right click and select devices see off, then set as default.

    I would like to know how everything goes.

  • I'm not all the sounds from the speakers. The volume is up

    I'm not all the sounds from the speakers.  The volume is up

    The following links may be worth a visit:

    No sound in Windows
    http://Windows.Microsoft.com/en-us/Windows/help/no-sound-in-Windows
    (Win XP / Vista / 7)

    (307918) how to troubleshoot sound problems in Windows XP
    http://support.Microsoft.com/kb/307918/en-GB

  • HP Wireless TV doesn't Connect - no sound from the TV

    HP G60 - 235DX notebook PC with Windows Vista.

    HP Wireless TV Connect WY555AA #ABC model

    Connected to the HDMI port - 2 on a Samsung HD 52 '' TV

    The video is great, but no sound from the TV speakers. Sound plays on the mobile speakeres.

    I checked the Device Manager on the laptop and the drivers are up to date and there are no conflicts.

    Help, please.

    Thank you

    Hello Larry,.

    Please take a look at this document, which provides troubleshooting steps that should help you resolve your problem of 'no sound', connecting your laptop to your Samsung TV via an HDMI cable.

    Please let me know if it helps to solve your problem.

    Good luck!

  • I have my Dell XPS HDMI cable to my Sony Bravia TV / I get the image on the TV but the sound from the laptop

    I have my Dell XPS HDMI cable to my Sony Bravia TV / I get the image on the TV but the sound from the laptop

    Thank you.  I had to go to the sounds and have speakers/headphones to HDMI it didn't work at first but founmd you need to have the TV and the computer.

  • No sound from the microphone in Windows 7.

    Original title: Add a microphone to windows 7

    Hello I am trying to add a microphone to windows 7.  I put in the pink jack point on the back but no sound. I'm redoing a voice on a software program Pinnacle while the editing of a film that I took.  Thank you very much

    Hi Linda,.

    You are able to get the sound from the speakers?

    You can check if the microphone works on another computer.

    You can also try to run the hardware troubleshooter and check if it helps.

    Convenience hardware store

  • Why the last OS update cost me gigabytes of data when you are connected directly to my computer and ISP via Itunes February 29, 2016

    Why the last OS update cost me gigabytes of data when you are connected directly to my computer and ISP via Itunes.  29 February 2016

    While it is connected to ITunes via my Dell system, I was informed of the latest OS update for my IPhone 6.  I decided that the direct connection to the internet would be the fastest way to download and install the software.  During the process I started to have some warning of our AT & T account that I approach the limit of our data plan, then in quick succession, only warnings, said I've reached the limit and then passed in the data, limit charges.  At the time it was done, I had accumulated more than 2 gigabytes of additional data charges.

    Until that point, I was very pleased with the device and confident in the ability to use Wifi and data.  Due to this incident, I became very suspicious of the camera and the huge potential for data overcharges. It is extremely disconcerting as it happened while it is directly connected to the internet using my computer at home.

    Please note that, in the episode my ISP and the computer is remained connected to the WEB with no sign of connectivity issues.

    Someone at - he had a similar experience and understand what went wrong?

    Thanks for your support,

    Jerry

    JerrolK wrote:

    Why the last OS update cost me gigabytes of data when you are connected directly to my computer and ISP via Itunes.  29 February 2016

    While it is connected to ITunes via my Dell system, I was informed of the latest OS update for my IPhone 6.  I decided that the direct connection to the internet would be the fastest way to download and install the software.

    You have chosen the option of direct download, you have received a message of warning from AT & T about it yet.

    He did what you asked it to do.

  • Camileo Clip as a webcam: how to get the sound from the microphone?

    Hello.
    The * Camileo Clip * might be a nice * webcam * _If there... the sound_ with the video.
    Is it possible to have the * microphone * the task force Camileo Clip when used as a webcam?
    Thanks in advance for your help.

    Hello

    Unfortunately I m not the Camileo Clip owner but according to details that I found on the Web pages, the camcorder can be used as a webcam so I guess you can also record sound by using the Clip as a webcam.
    Usually, you choose the default microphone for recording.

    Maybe you should check the settings in:
    Panel-> Audio-> recording (2nd tab from left) tab

    If the webcam mic would be visible, choose this option by default.

    I also recommend you to check the webcam settings and choose the video mode.

Maybe you are looking for