No sound on Satellite M30

Similar Questions

• How can I check sound version and watch on Satellite M30 power?

  I have a Toshiba Satellite M30 series and have lost my audio. I don't know if I checked something l ' turn off or what. Can someone give me some ideas on how to check it? The other is stupid - how do I know what saving use?

  Right now my setting is on Power Saver 2 and I'm having problems, that I found an answer to this, of overheating, but it was suggested to check the energy saving, how do you know that one to use?

  Any help will be appreciated.

  Hello

  It's very simple. You should visit the Toshiba driver page and you will find the correct drivers and utilities also energy saver.
  After the installation of the power saver you use defined parameters. The cooling method, you can define if you want to cool the most powerful CPU for maximum performance.

  Now on your noise problem:
  Well, first go to Device Manager and check the status of the sound card.
  If there is everything is fine and there is no exclamation point yellow if all the drivers are installed and working properly.
  In this case I recommend to enter the control panel and select the Audio & Sound devices. There you can check if the 'secret' was not enabled and if other controllers are defined at the higher value.

• Satellite M30: Unknow Hard Error - could this be a problem of hard drive?

  I got my Satellite M30 for 2 years now and it never gave me any problems, until a few weeks ago. The problem started shortly after I put Windows to SP2, when I played a game it would stick for a minute or two, and then continue on as usual, the problem slowly got worse and started blue screening with "Unknown hard error" and sometimes strange balloon in the lower right corner saying unknown hardware error and then freeze it. It also took a long time to start and generally do nothing.

  Assumed it was a problem when I've upgraded to SP2, so I decided to reinstall Windows and start over again, update the BIOS while I was home.

  Once this is done it seemed fine for an hour or two, but then tried to install a game and of course, the good old blue screen appears and the whole problem starts again.

  I took it to a repair shop and explain the problem and I had re-installed Windows nothing helped, and I suspected that it may be a hardware failure, I left it with them, and 2 days later I get a call saying its all fixed and ready to be picked up, I asked what was wrong with it and they said that they re-installed Windows and sound now works fine (i.e. what I their) I said, I had made and n t worked!). I picked up (and got charged £40 to have done what I had already done). I got it home and everything seemed ok... for a few hours, then blue screens seemed to tell me any physical dumping of beginning and the usual stuff.

  I think it might be a drive problem hard, like when I tried to install a game on it at night last light CD and HARD flash drive, one for about 15 seconds, then the other for a short time, data copied from one to the other, but then the HARD drive light stayed on, and I could hear the HARD disk as if it were sticky , after about a minute of this blue and close short-listed and took some time to turn back. If I leave a couple of hours and it starts fine until the next time.

  So, after my long description on my problem, I have 2 questions,

  1. could I be right in thinking that these problems are associated with hard drive?
  2. If I'm right, is easy to replace on the M30 HARD drive and where I would buy a new?

  Thanks for your time and help,

  Kenny.

  Hello

  The blue screen appears only if you play games?

  But I agree with you. In my opinion, there would really be a hardware malfunction.
  The question is - it s a HARD drive or something different?
  Hmmm. I think that the problem is not related to the disc HARD but maybe overheating?
  According to the publication, sometimes when you play games. The game is a high performance application. All devices running with maximum performance and produce heat.

  I m not 100% sure, but maybe the high temperature has a bad influence on the system and therefore the BSOD happens.
  You suggested that the laptop run properly for about 2 years. Maybe fans can cool properly because of the dust and debris. Two years is a long time if you have not cleaned the cooling modules and fans.

• Can not turn on the Satellite M30

  Hello everyone...

  I have a Satellite M30 laptop for time enough and I'm having a problem with it. When I try to turn it on, it makes a kind of scratch noise and then nothing happens. The hard drive lit wrath but the computer does no sound and no picture on the screen. I tried to turn it on with and without the battery and the same thing happens.

  A few days before this happened that I could see the windows startup screen, after that the computer crashed, even when I went to the BIOS Setup screen, the computer also crashed, so the problem was not on the hard disk. A few days later, when I tried to turn it back on, it makes a single probe and nothing else happened. Can it be a motherboard problem? can I try before sending it for repair

  I'm scared of m it s a serious problem.
  Depending on the symptoms that you described the laptop cannot get the message and so I think there may be an error on the motherboard.
  I don t think you will be able to locate the fault. It is simply not possible for the common user like you and me

  If you have no choice as to the request of the service provider for Toshiba for help.

• Ports COM1-4 'missing' Satellite M30

  Hello, communication ports (COM1-4) series of my sound of portable Satellite M30 suddenly "disappeared", or, at least, Window XP (Home version) is unable to detect them - through the management of resources or similar tools of surveillance - only parallel port (LPT1) is reported.
  Problem is that the modem (internal standard) (by default on COM3) is unable to work. Modem seems ok - at least according to Windows - but, as you can guess, it cannot accept AT command (and therefore start up).
  Everything else seems to work fine - including the Infrared Port, which should work, by default, on COM4? and mouse Touchpad. No problem i/o and IRQ address is detected on the other peripherls.
  Only the system serial port driver (serial.sys) is alarmed that unable to boot because.
  ..??? .. Even thought a hardware problem - ex.electrostatic discharge or similar? - but a couple of days ago the modem starts unexpectedly and worked correctly for long enough - even if with the COM ports still without being detected by Windows - but after connection went down and modem could not start (Error 633: modem, a device already in service or other problems of configuration...).
  .. Before proceeding to more annoying (and probably expensive) actions - such as reinstalling Windows?... or looking for a repair center - I wanted to try to replace the driver (serial.sys) series, but I was unable to find it-in the CD provided with the product or on the Toshiba site. Where can I find it?
  Other suggestions?
  Thank you

  Hello

  Don t look for serial port drivers. These ports are using simply common Microsoft Windows drivers!
  According to your description there are different problems with different internal devices.

  If all goes well it of not a hardware problem?  :|

  So in my opinion we must first know if it s a software or hardware problem.
  In this case you take your original Toshiba Recovery CD and must be reinstalled the operating system.

  Note; the whole HARD disc will be fomrated and you will lose data. So, don t forget to back up your data.

  If the new installation of the operating system didn't help any, and you will always receive error messages the technician must check the laptop!

  Good luck

• Satellite M30-S309 - certain proportions on external monitor not right

  Hello world.

  I have a Satellite M30-S309 that I just started to use it with an external monitor: a 191EW9 of Philips, which has a maximum resolution of 1368 x 768. The built-in monitor is 16 "; the new external monitor is 18.5 ".
  The computer has the driver for the new monitor, but with a few photos of the proportions are obviously not right.

  Anyone know of any way to solve this problem? Or it's an old computer like this all simply not up to handle this type of monitor?

  A solution would be much appreciated.

  Hello

  Can you please explain what you mean with certain proportions are not suitable?
  You can choose the native screen resolution of the external display or use another resolution of the screen?

  To me that sounds like this, you use a wrong setting. On the screen you can change the width, height and to this day. You should check these options.

  Welcome them

• Satellite M30-107 does not start successfully after using recovery disk

  Hello

  I recently got my hands on a toshiba Satellite M30-107 laptop second hand and decided to freshen it.
  I used the toshiba recovery disk, but after that the laptop is no longer support windows.

  When turned on it shows booting Toshiba disc for about a second then goes to a screen blank and freezes.
  When turned on, once again, a screen will appear an error by stopping and offer the opportunity to start in SafeMode etc but choose one of the options causes the machine to freeze.

  Any help or advice would be much appreciated.

  Thank you
  JT

  Hello

  Sounds a little like the laptop does not start because of the problem of Windows software
  You did not recover the M30 with the original Toshiba that was provided with this device M30 recovery CD?

  I may be wrong, but to me it looks like a recovery CD incorrect has been used and an image with drivers not compatible m has been installed

  You can try to install the OS of Microsoft Win XP original CD and could check if it would be possible to get the notebook ruin using own BONE.

  In this case we (you and me ;)) might know if this problem could be related to hardware or software.

  Good bye

• Sound distortion on M30 - 604

  Hello

  I had a problem with the sound on my Satellite M30-604. So for now I play a cd or an mp3 player (doesn't matter with what program), the sound is distorted. It sounds a bit like back in the old days when my channel am stuck. After some time, the noise goes away completely and I get an error of the pilot of its bad. When I restart the laptop, the sound works again fine for awhile, but then the problem repeats. This temporary regeneration happens only when I restart and happens when I put the laptop in mode or mode standby sleep for awhile. The rather in my book is the SigmaTel C-Major Audio version 6.14.1.3835, it should be the latest version. Can someone help me with this problem? At the moment I'm not shure even if it is a hardware or a software problem. Thank you

  Steve

  Hi Steve

  I hope there is a solution that will help you. Have you tried to update BIOS? It will be interesting to know what you mean exactly under sound distortion. One of my friends had a similar problem, and that the cause was the modem. Sounds stupid, but everything is possible.

  As I said if the sound is slow, it may be a few mailfunction of material.

• Satellite M30: Does not start XP

  My Tosh Satellite M30 laptop (with 2 HD discs) does not work after I have updated with the MS security updates, it does not start XP.

  The laptop makes a clicking sound and gives me the message:

  PXE - E61: Media test failure, check cable of
  PXE - M0F: Exit PXE ROM
  Operating system not found.

  I changed the boot order in the BIOS to: CDROM. And select Exit and save changes.
  Inserted my Toshiba Recovery windows XP version that allows me the option of
  "1. the recovery disc" or "2. Expert recovery mode"or also"Exit ".
  I chose "1. Recovery disc"as I'm not an expert (as you can tell!)

  I then get a load of diagnostic checks run by laptop and it shows then finally on the screen:
  X:\\ no disk fixed

  Ideally, I would like to repair and keep things I have on my drive D: HD.

  I'm pretty sure the XP starts on my drive C: HD.

  Your help is very appreciated!

  Suraj

  Hello

  The PXE message means that the device is trying to boot from the network. I put t understand you a lot with C and D HD. I assume you mean that you have two partitions on a single HARD disk. C partition for the operating system and the D partition for your data.

  If I understood you as soon as you cannot boot operating system at all. On this path, it is not easy to say what may be the problem but obviously you a problem with the HARD drive. It is probably defective. If the recovery DVDs is not able to detect one that there may be a serious problem.

  I put t know how contact the partner old Service your unit is but if the warranty is still valid and let check the device.

  Good luck!

• How do Toshiba's energy-saving work on Satellite M30?

  I recently had to reinstall XP on my Satellite M30 PSM33A

  I have most of the pilots but were not able to get Toshiba saver work, nor the keys FN, the drivers I downloaded installed on-site, but saying "cannot open as you do not have access rights.

  It's frustrating because my screen is really low.
  In addition, my CD player but works I can not read the DVD - it says I have an incompatible driver and I tried everything

  Can anyone help? See you soon

  PSM33A must be Australian model laptop so please download all the drivers, tools and utilities http://www.isd.toshiba.com.au/71/live.dll/topic/content/driver_search.jsp?MODE=NPRO&CATOID=-15058

  You will find all the things you need. I don't know what the problem is here, but please install all the stuff following this order of installations:

  1 chipset Driver
  2 Microsoft Updates
  3 display driver
  4. Common Modules
  5 Hotkey for display devices
  6. the utility change device screen
  7 sound Driver
  8 touch pad Driver
  9 YPP/power button Utility
  10 driver modem
  11 V.92 Modem Driver
  12. wireless network driver
  13 Atheros Client Utility
  14. the network driver
  15 infrared driver
  16 ConfigFree
  17. SD host controller driver
  18. SD memory card driver
  19. SD memory card format
  20. power management
  21 utilities
  22. the buttons
  23. the console
  24 DVD player
  25. drag / drop
  26 CD/DVD Drive Acoustic Silencer
  27 skins for Windows Media Player
  28 user manual
  29 Screensaver
  30 wallpapers
  31. Sun Java Runtime Environment

  I hope this will help you to install all drivers and Toshiba tools and utilities correctly.

• Satellite M30 - beep Constant and powers On / Off by itself

  Last night I turned on my laptop Satellite M30 Special Edition and the login page appears, as usual. However, after entering my password the screen just went black and is stuck like this. After waiting a few minutes, I turned off the computer (hard restart my only option) and that's what Toshiba technical support told me to do the last time this happened (a few years ago). This is where the real trouble started.

  Tried to come back on the computer, but in addition to the white screen now is a constant beep sound (like a key is stuck perhaps). The only way to make the beeping stop was soft reboot of keys, which I did several times. CTRL-Alt-Del would stop the noise and computer would shut down for a few seconds, but then immediately join the beep goes again. I finally managed to get it remains powered off mode, which is the way he currently remains.

  I tried to unplug the AC and remove the battery and nothing, which makes sense. Just AC, he did the same thing, so try does not seem to be a battery problem. Tried to power a few times and always the same situation - white screen, the beep and the need to hold the power button for a few seconds get the machine to stop and stay off.

  Help, please!

  June

  P.S. I contacted support and they suggested to bring it to an authorized service center, but I don't want to pay large sums of money to fix something simple and and I don't want to pay for a serious problem that can't really be healed/fixed. Any advice or suggestions on what could be wrong would be greatly appreciated.

  Looks like a hardware problem - probably the motherboard. The only solution would be to take it to a repair center.

  I hope it's just a change in minor liquid that has damaged the keyboard, which should not be expensive to replace.

• Satellite M30 - possible repair broken?

  My father seems to have broken his laptop (Satellite M30-107), which is the model above.

  When you press the power button it turns on but there is no sound what it is running because I expect. There's no display on the screen. Also the cd drive does not so much need to open manually.

  If I button green light comes on to show so you have power to the keyboard.

  I tried to connect an external monitor, but that does not work either.

  Does anyone have any other ideas I could try? Or know where I could take it to be fixed because it's about 1 week out of warranty :(

  Hi Martyn,

  The first thing to try is to remove the ca cable and also the battery so that the laptop is completely isolated from any power source, then leave it for 5-10 minutes prior to re - attach the cable ca.

  Try turning on the laptop so normal and if you have the same problem then discopnnect the AC cable and install the battery and try again feeding.

  If the laptop still does not power on then it is likely to be a problem with the motherboard that will have to be checked by an authorized service center.

  Kind regards

• Satellite M30: I can't lock in my wirelesss network

  Hello people,
  I have a Satellite M30 and since yesterday I can not lock in my wirelesss network. Every now and then I see the network, but I can't establish a connection. Additional, the sound and the mouse pad is stuttering when the wireless is enabled, both is fine when wireless is spent.
  I got the system, but the problem is still there.

  Any help for me out there?

  Stephan

  Hello

  A secure wireless network?
  If so, it is possible to s as you type a wrong security password.
  Believe me it's not easy to say what goes wrong.
  Sometimes, the update of the wireless driver to solve a problem.
  Please see the Toshiba or Intel page to update the wireless driver.

• High temperature CPU on Satellite M30

  Hello

  I have a Satellite M30 852 with Pentium M 1.5 GHz processor. My problem is that the heater does not start until the CPU temperature reached 70 degrees, which I think is a bit high, no mention that when it has reached this temperature I can not keep the laptop on my legs because it burns... and also to kind of warm around the touchpad and left side of the keyboard.

  My question is if there is any software I can use to take the cooler start at low temperatures, to keep, or if there is no setting I can adjust the laptop utilities to solve this problem (in addition to throttle CPU cooling where is defined in the performance).

  Thank you all in advance!

  Could PS: Anyone tell me which button support when starting, to get into the BIOS...? Because the F1, esc or del does not work.

  Post edited by: master of ceremonies

  Hello

  The temperature of 70 ° C nothing unusual and in my opinion not too high.
  Is that it s not recommended to use the laptop on your legs or in bet, etc.
  You should always be sure that there is enough free space (left, right, bottom) around the laptop for the circulation of fresh air!

  Usually, the Toshiba power saver controls the cooling method and the CPU processing speed. If you want to change some settings you should the fact in the basic power saver menu.

  PS: on m30 the phoenix BIOS has been installed and therefore, you should use the F2 key.

• Satellite M30, partitioning

  After that I got some error messages and viruses so I had to format my laptop the Satellite M30.
  I used the recovery CD Toshiba 2 and the only option for me was Option 1 Option 2 is reserved for specialists, and I'm not familiar with all the terms it. In any case, the formatting not only formatait the C:\ but D:\ thus merged the formerly 2 x 30 GB in a single C:\ partition, I had no option to stop this.
  How can I split my C:\ drive again into 2 partitions of the same size?

  Sorry, but the only way with the delivered software on a M30 to create partitions is the expert mode.
  As far as I know.

  But I have a proposal.

  Tomorrow I'll do a recovery on my M30 will inform you as soon as possible.

  Good bye