No Swap COS configured

Similar Questions

• Windows 7 does not take into account swap file settings

  I have Windows 7 Professional 64 bit installed on a system with a mirrored system disk and two disks no mirroring, including a SSD drive which is configured with ReadyBoost. Because mirroring is to the integrity of the data, and has a performance cost associated with it, I don't want any file on my system disk. Instead, I want that page files on non mirrored disks.

  So I use computer-> properties and go to the "advanced system settings" to bring up the System Properties dialog box. I click on the "Advanced" tab and in the 'Performance' section, click on 'Settings' to bring up the "Performance Options" dialog box Then I click the "Advanced" tab and in the "Virtual memory" section, click on 'Change' to bring up the dialog box 'virtual memory '. Here, it lists the drive letters and for each drive paging file options.

  I put the SSD (:)) has 'Custom size' with ' Initial size (MB): ' as 24576 and ' size maximum (MB): ' as 24576, click on 'Set'. "" "")

  I put the other disk not mirrored (b) 'Custom size' with ' Initial size (MB): ' as 24576 and ' size maximum (MB): ' as 24576, click on 'Set'.»»» "

  I put the system disk (c :)) "No paging file" and click "Set".) I also tried setting the system drive (c :)) "Minimum allowed" value of 16 MB (size initial and maximum size).)

  I get the warnings appropriate, if I didn't put "No paging file" and accept the consequences. If I put the pagefile to 16 MB on the system drive, I don't get a warning of not having a swap file.

  I reboot, to let the new settings take effect. When the system is in place, if I put "No paging file" on the system drive, Windows tells me that it has created a pagefile on the system drive, and the file is approximately the same size as the physical memory, i.e. 12 G and the "Performance Options" Advanced tab reports that "the file size for all readers of Total paging" is 12288MB.

  If, instead, I put the system drive for the authorized minimum 16 MB paging file, Advanced tab "Performance Options" reports "Total paging file for all readers size" is 16 MB.

  In any situation he always respects the settings specified in the dialog virtual memory for other readers.

  I checked that 'HKLM\SYSTEM\CurentControlSet\Control\Session Manager\Memory Management\PageFileOnOsVolume' is set to 0, and 'HKLM\SYSTEM\CurentControlSet\Control\Session Manager\Memory Management\TempPageFile' does not exist OR has been set to 0 (Windows always change this parameter to 1 if I chose "No paging file" for the system volume.) So, I change it to 0, reboot and Windows it passes 1 ad creates the 12288 MB pagefile on the system volume).

  I disabled BitLocker - it does not start.

  I don't really know what hoops I have to pass through to convince Windows to use the swap file configuration that I specify. At the very least, if I put in place minimum swap file on the system drive, to avoid the essential consequences pagination on a mirrored disk performance and to prevent Windows from automatically creating the 12 G pagefile on the system drive, I expect that the other swap files on non mirrored disks will be used by the system , but dialogue "Performance Options" it is clear that single paging file in use is the one on the system volume - exactly what I don't want.

  Can you please tell me how to get Windows to my settings?

  Hello

  Please contact Microsoft Community.

  We have specific forum for the RAID configuration operating system and they are experts in this field of investigation and would be in a better position to address the concerns. So refer to the link below and post your query on the TechNet Forums.

  https://social.technet.Microsoft.com/forums/en-us/home?category=w7itpro&filter=AllTypes&sort=lastpostdesc

  I hope this helps. If you have any questions on Windows, please answer. We will be happy to help you.

• SRM and the volume of replication

  Hi guys,.

  I have a client who seeks to implement the SRM.

  Available to the virtual machines are as follows:

  • system on vmfs1 VMDK

  • VMDK vmfs2-data

  • Windows swap file on vmfs3

  • VM vswap files vmfs3

  VMFS 1 & 2 are replicated but not 3. They tried to reduce the amount of unwanted changes block replicant.

  Have I reason to say that they would have to replicate vmfs3 (even just once) to allow sucessfully SRM protect virtual machines?

  Has anyone else came across such a configuration?

  Thank you

  Dougie

  You don't need to reproduce your vmfs3 volume.

  Just follow the procedure "avoiding replication of paging files and other transient data" of the SRM administration guide.

  Machine configuration virtual swap sit on no replicated data store is pretty easy, but the swap file configuration is not that simple and requires several steps to be completed for each virtual machine, including cloning VMDK, the VM configuration, operating system setup and configuration of SRM.

• How to find out the max mem can be allocatedTT for 32 bit Win?

  How to find the maximum size of permanent and temporary data data size that can be allocated for the Oracle times ten for Windows 32 bit OS.

  The maximum size that can be achieved depends on three main factors:

  1 system (memory, swap file) configuration.

  2. connectivity method (direct mode compared to the server). Direct mode is more limited than client/server (but is much faster).

  3. for a DBMS direct mode, the number and type of dll that the application uses. Console mode apps can generally for example to reach a size of datatstore much larger than .NET applications.

  The maximumn size will usually be of the order of 600 MB to 1 500 MB. The only way to determine a specific value is to try it. With your application, start with a store of 1000 MB and data increase decrease until you find the breakpoint.

  In fact, 32-bit Windows is not a good platform for hosting of any significant size data warehouses. 64-bit Windows is much better (and it works almost all the 32-bit applications without any problem).

  Chris

• Tower of EliteDesk 800 of G2: 800 swap system G2, computer Board is not fully configured.

  I just swapped a systemboard in a 800 G2. Installation is finished it and went into the bios to set the system ID's

  I have put all the your computer and I screamed a few times for typo'ing the FeatureByte, then it took. I rebooted and it jumped me in bios, asking if I wanted to validate the settings. Everything seems OK, then I say Yes.

  It restarts again and now I still see the message "the system is not fully configured" at startup.

  It gives me no indication of what the problem is.

  The configuration menu of the ID system is finished now.

  I tried to boot into the bios and hit ctrl-a to see if it would work, but I see nothing on the system ID in the Security menu.

  Any other suggestions to find out what is the cause?

  The tech came out.

  He could not get the editing mode (ctrl-a) to display the system id in the Security menu is.

  He checked that I have entered all the information correctly and that he was perplexed as well.

  He was on the phone with HP to order another motherboard when, after a few dozen restarts, the error has disappeared and has not returned.

  Nothing has changed in the bios. as we were able to edit previously entered values.

  I have no idea what caused it disappear, but we can mark this issue is resolved.

• Computer configuration virtual for SRM - files from memory Swap file/Virtual - best practice replication?

  Hello, I am very new to the model DR VMWare and have a few persistent questinos.

  What is the recommended best practice re: virtual computers invited windows and virtual memory files.  I think it would be unnecessary to replicate these changing data on the DR site.  I have several virtual machines with 6-8gig memory and I'm just wondering how can I isolate the ESX memory swap files and virtual memory in Windows feedback, so they get not replicated on the Dr site as often as changing os/data.  If it's even necessary to replicate.

  We use vspere vcenter 4.1 related modes, RS 4.1 the two on-site Cellera NX4 ReplicatorV2.

  I wonder if I can install the files of pages to be in a condition NOT replicated file system or a file system which is the only value replicates every 24 hours, or once a week.

  My reasoning here is.  Once the file is there, the operating system really cares about the changes in this file and dumps windows virtual memory on a restart, as well as the .vswp file.

  what I mean is built on a virtual disk full and placing the windows file on this virtual disk to Exchange.  This virtual disk could exist in a data store hosted on a celerra file system that does not get repeated as frequently as data/OS file systems.

  or am I completely off base here.

  I think that if you tried to reproduce these files and maintain a sync time minute 10, you would need a ton of bandwidth.

  any suggestions or recommendations or even pointers to Articles/items worth points = D.

  Thanks for your time.

  Given that the configuration is made at the level of the cluster and has no impact on the SRM, replication is not a factor.  Don't forget, not to replicate the LUNS with the swap, just files have a LUN configuration on the side of recovery as well and have this defined cluster Exchange files.  Also, on the virtual machine critical we define reservations memory so the pagefile is not a factor at all.

  Kind regards...

  Jamie

  If you found this information useful, please consider awarding points to 'Correct' or 'useful '.

  Remember, if it isn't one thing, it's your mother...

• How can I configure my wifi network to the big house?

  We are in a House floor (including basement) large 4 4500 square feet.

  Internet comes home in the basement.

  From there I push a switch that distributes internet cable throughout the House.

  Everyone has now 15 years later, wireless devices.

  I have 5 Airport extreme, what is my best option to implement?

  I want to have the name of a network and a password.

  I would like to be able to move anywhere in the House and have internet without needing to connect to different networks.

  Any help would be greatly appreciated!

  It is the standard of roaming network.

  Wi - Fi base stations: install and configure a roaming network (802.11 a/b/g/n)-Apple Support

  Wi - Fi base stations: extend the reach of your network wireless by adding additional base stations Wi - Fi - Apple Suppo...

  Apple does not seem to have a newer version... in order to take the principles that are simple.

  Æ all have a simple base station name... I recommend names that are short without space and pure alphanumeric for everything... not to use apple recommended names in the utility.

  If you have AE1 - AE5.

  All units to create a wireless network... (More.. important to create not extend).

  for example AEwifi

  All units are configured with WPA2 Personal security and use same pure alphanumeric past 8 to 20 characters.

  All devices are set to fill mode, except maybe the main unit being used as DHCP and NAT router.

  Plug in ethernet in the appropriate floor and location.

  You now have a roaming network... It works great to move home with laptops... It may work less well with phones and ipads... It's Apple's fault for not allowing the device swap "tours" like on the side of the 3 G... You may need to turn on/off the wireless. I hope that one of these days the problem will be corrected.

• Automatic configuration of the HP w17e monitor active at random

  Currently using an hp w17e flat, wide LCD screen connected to a NVIDIA 9500 GT video card located in a computer that is running Windows Vista Edition home premium (32 bit).  Running on 1440 x 900, 60 Hz frequency suggested by the insertion of the packaging of refreshment. Also in the 32-bit color setting.

  (Other computer stats available at http://www.compusa.com/applications/searchtools/item-Details.asp?EdpNo=4419976&sku=T71-3446%20ON&srkey=3000%20H210%2057088788)

  Tuesday night (13/10/2009) let my computer playing music with the monitor off.  Morning, Weds(10/14/2009) and any platform is off.  Turn it turn it back on and seems to update windows pushed a lot of updates.  Then I noticed the problem.  Randomly, the automatic configuration of hardware on the monitor turns on.  Tried different applications (games, firefox [windowed and full screen], or just sitting on the desktop), and the Automatic Configuration dialog box appears in the center of my screen and shakes the screen.

  Monitor checked button, it is not blocked (before this, don't think I hit a few months...)

  No change, I tried older drivers I had before the update of windows, still didn't try to update the NVIDIA drivers, arrives.

  Reset the monitor through the monitor menu.  Still happens.

  Reset the NVIDIA graphics settings, still happens.

  Installed the update optional windows update for the hp w17e LCD wide display.

  Monitor connection video Cable disconnected to the video card, checked pins, pins are good.  Reconnected.  Still happens.

  Tried to connect to another video on the port of the video card (always the same type of connection).  A reduced frequency, but screen looks flatter and more gray/less dynamic.

  She returned after swapping the video ports when I open the NVIDIA Control Panel.  Didn't jump once while typing this.

  Suggestions?

  Updated several days later.

  After the passage of the screen to the other video port on the back of the computer (vid card has 2 ports I could use, been using a) and disconnect / reinstalling the power cord on the monitor itself, auto config jumped just once shortly after reconnection of everything and not since.

  Weird and intrigues me, but hey, if it works now, will to run with him.

• Disabling update the configuration file without stopping the VI

  I would like to perform a function that when the new modules are added in the existing system of the public Service or hot swapping modules autour, the VI can update its configuration file. I don't want the VI to stop we will collect data 24/7.

  I use cFP2220 and two or three modules of different types. I have my work VI and it is fairly straightforward FP read.vi in a time loop. All data are stored in the database using the Labview database tool. My screws are hosted on the local PC, not on the controller. I'm using Labview 8.6.

  I guess I have to get the file configuration (iak), whenever new modules are added, the iak file can be changed (without MAX aperture). In any case, I would have the flexibility to run the VI continuous. I know there is a similar code here: http://zone.ni.com/devzone/cda/epd/p/id/3221and they get the configuration file in the ini file. But I don't know how it's done as I can save only the configuration file as a file iak for FP system.

  Another potential problem associated with that, I guess, is the database format. For now, I use a three column structure, i.e., DateStamp, value and ChannelID. In this case, if I want to add/remove/swap channels, I can just change the ID of the corresponding channel. What happens if I have a horizontal arrangement of the database, namely 10 columns corresponding to 10 sensors, would he be in trouble if I change channels modules?

  Thank you very much.

  There is a way to change the module and programmatically updated the IAK file without stopping the VI.  You will need to change the FP read.vi front right by with the constant e/s FieldPoint.  You will need to use the Open FP, FP create Tag, read FP, and close to the public Service.  The trick to this is that you must pre-create files IAK in MAX first.  The way to do is to set up your cart in a configuration and then find devices to MAX.  Then save the iak.  Then reorganize your bottom of basket to the next setting would have desired, then have MAX find devices and who save in a file different iak.  You will need to do this for each configuration you have.  Then, you need to place the code below when you want to Ministry the configuration file.  I have also included a screenshot of MAX that you can see what the strings are correlated with.

  

• swapping hard drives between 8115-PXI and PXI-8105 won't boot to the top

  I have a test system running Windows XP on the PXI-8105.  I have upgraded the full test for another project system and upgrade my existing systems; the upgrade works on Windows 7 and PXI-8115.  I have Windows 7 and the new test software of new hard drives that have been loaded/configured/tested on a PXI-8115, but I need to modernize the PXI-8105 with them.  It does not work.  Windows begins to start, but fails and trying over and over again.  In order to make the PXI-8105 offline to troubleshoot, I replaced it with the PXI-8115 and the old disk (WinXP).  It did not start, either.

  Here is a summary of my situation:

  • An old a PXI-8105 system running Windows XP
  
  
  • A new system has PXI - 8115 Win7 running
  
  
  • A hard drive (with Win7) since the PXI-8115 does not start on the PXI-8105
  
  
  • A hard drive (with WinXP) since the PXI-8105 does not start on the PXI-8115

  What is different between two controllers PXI that prevents me to swap hard drives?

  A technician with 'the knack' discovered a device driver conflict.  We have removed this driver and Windows was able to use a generic driver to start correctly.  Bob's my uncle.

• W540: Optimum Configuration RAM

  I recently added 8 GB of RAM to my W540 (2 x 4 GB) to complement my existing 8 GB (2 x 4 GB). The existing memory is that the factory installed Samsung memory (PC3-12800). I bought a few Crucial PC3-12800 with a latency higher case. I would like to adjust so that one of my two memory channels is only to Samsung and the other is Crucial.

  Currently I have the memory Crucial on the two slots closest to the keyboard and the nearest the bottom memory Samsung. Speccy says that is Crucial memory in slots 1 and 4, while the Samsung memory is in slots 2 and 3. It is the most effective configuration, or should I swap two of the slots?

  You find it difficult to notice a difference, but a pair must be next to the motherboard. (one on top and one on the bottom) The other pair should be on 2 more slots away from the motherboard

• Incorrect regional keyboard localization (and @ swapped) of the 2010SP1 of TestStand

  Numpty question here...

  3 of us use TestStand 2010 SP1.

  2 of us have problems with the regional keyboard mapping being wrong - it is the " " " and @ key are swapped - but it seems like only in TestStand.

  The keyboard of the other user mapping is fine.

  We have all the same keyboards (English - UK).
  We have all the same settings under Configure > Station Options > localization (English language).

  All other Windows work fine on our PC (office 2010 etc.).

  So where is TestStand pick up its regional location and how to solve this problem!

  Thank you very much

  Alan

  Hi Alan,

  Thanks for your post on the forum. It seems TestStand another user has experienced a similar problem in 2010 SP1 by which its default keyboard available to the United States when he used the layout (i.e. German).

  The problem has been resolved in the post on the forum here.

• HP Officejet Pro 8600 no possibility to configure the Port

  My OS is Win 8.1 (last version), latest version of the printer driver, last wizard to install printers used.

  My first printer "HP Officejet Pro 8600" folling down on the issue of the screen. I'm doing a swap with the same model, I have to uninstall and reinstall the full with Wizard, now I have some difficulties to recognize the printer.

  -Shortly, no communication!

  -A few times, printing find after printer communication error.

  If I go to "Properties/Port/port" I got "Error Message.

  > An error occurred during port configuration.

  > The file name, directory name or volume label syntax is incorrect.

  Could be a former key stay in the registry (with the old link to the printer)

  I have to uninstall and reinstall the wizard fuul without success.

  Now the analysis feature does not run and printing run with delay.

  Major Remarq:

  I have no problem with MAC OS 9.x to 10.10.1

  Thank you very much in advance for your support

  Hello

  The port must not be changed that way but through the HP software, it is managed by the software and such a mistake is planned during the attempt to change the port...

  Try opening the HP Officejet Pro 8600 software, and then click the Utilities.

  Click Update IP address and type the IP address of the printer, which can be found by clicking on the icon wireless/network at the top of the Panel before you the printer.

  Click on save and confirm, then close and reropen the HP software,.

  What happens when you try to scan now?

  It'll work, or is there a specific error or behavior?

  As well try now the doctor of printing & scanning HP, it is listed under the Utilties batn so, follow the steps on the screen by selecting the difficulty of analysis and let me know the results if you are still having problems.

  Shlomi

• 2x2.5 Z1 for the swap drive hard 1x3.5

  I have a new Z1 with the 1 TB 3.5 hard drive, which seems a bit noisy for me - not strong but sometimes annoying. I think I want to swap out for 2 2.5 HDs, a 128 GB SSD for the operating system, programs, and the second a spinner of 750Go. I checked with technical support to see if I would need an adapter and told me "the workstation requires one of the following carriers supported: 671193-001 supports a 3.5-inch disk hard;" supports a 671192-001 or hard disks of 2.5 inches of tw. "This was taken directly from page 48 of the Service Guide and Maintenance Z1 HP. But I can't find the list of one of these pieces on the HP site or anywhere else. What I find is the reference to B2P96AA, which appears in many places for $79 and more. Described on page 5 of the HP downloadable booklet "develop feed you - HP Workstation accessories" as the "HP Z1 HDD carrier Kit (for 3.5-inch drive or two 2.5-inch drives."

  "Does anyone know if the B2P96AA is another part that is installed in a new Z1 configured with a 3.5" drive. »

  Both Z1 product descriptions and description of part B2P96AA clearly suggest that a Z1 should work with either a disk 3.5 "or one or two 2.5" or readers without any modifications or additional investments.

  Maintenance of workstation HP Z1 and Service of Guide, page 48...

  The workstation supports only SATA hard drives.

  The workstation requires one of the following carriers supported:

  671193 001 supports a 3.5-inch hard drive

  671192 001 supports one or two 2.5-inch hard drives

  It is not possible to combine a HDD 2.5 inch and 3.5 inch hard drive.

  No cables adapters are required for all hard disks. The necessary cables for all hard drive configurations are included in the base system and automatically "blind mate" or "direct connection" to the drive during installation.

  My advice is to open your computer and pull the existing disc holder. This reference number, it is on this carrier?  Look at the space where the existing carrier came of... are there links to two discs? Do you see a space for a second aircraft carrier in the car?

  I tried to set up a company Z1 CTO and all readers have been listed as SFF (small footprint). It seems that hard drives 2.5 "come in up to 5 different heights... 5, 7, 9.5, 12.5 and 15 millimeters.

  Call HP about the correct configuration customer support and reference numbers. Two drives 2.5 "in two carriers? or two 2.5 "slim / SFF readers in the carrier waves? or what?

• Swap hard disk

  I have a R61i with a screen that does not work and cannot be repaired. I can buy a used R60. I can swap the hard drive of my R61i a R60?

  Welcome to the forum!

  Yes, you will be able to use this drive. Some drivers - depending on the exact configuration of these two machines - must be updated.

  Good luck.