No update since vCenter and ESXi 4.1

Similar Questions

• Manager Update for esx and esxi 4.1 problem

  I have data center contains esx esxi 4.1 and 4.1. Could you please tell me which version of the Update Manager I need which can cover the esx esxi 4.1 and 4.1. Should I server database to store the data of the Update Manager or just download the plugin and configure it to data center. Please guide me.

  You must create separate database for MUV. Most of the patches require a reboot after installation

• 4.1 - > 4.1 U1: vCenter update first and ESXi hosts later?

  Hello

  About the update 4.1 4.1 U1, y at - it order to follow?

  1 vSphere client

  2 vCenter & update manager

  3 ESXi hosts

  Thank you.

  It is always advisable to update vCenter Server before upgrading anything else.

  1 vCenter Server

  2. Update Manager

  3. the Client vSphere + new Update Manager Plugin

  4. the host ESX (i)

  André

• Update Server VC and 5.5 ESXi hosts to update 3 b (Build 3248547)

  I'm in vCenter Server 5.5 and 5.5 ESXi hosts.  Both are updated 3A, patched to version 201510001, which is the build 3116895.  I plan the upgrade of update 3 b (Build 3248547) and I'm a little confused on the question of SSLv3.

  I wonder if this point below ESXi55 U3b & VC 55U3b Known Issues applies to my config:

  ESXi does not automatically added to the inventory of the vCenter servers
  If you install an earlier version of vCenter Server and vSphere Update Manager for ESXi 5.5 updated 3B, then after the task of sanitation, ESXi does not automatically added to the VC inventory. Remediation process never gets done and ESXi State of connection in the VC inventory is presented as disconnected. Solution: When you restart ESXi after reorganization process is started, enable SSLv3 on ESXi (which is disabled by default). This will ensure that ESXi is added to the VC inventory automatically in minutes and sanitation as completed.

  If I'm reading things correctly, upgrade to vCenter Server to 3 b first and then upgrade the ESXi hosts, will avoid lost communication problems.  Can anyone confirm?

  It should be good if you update vCenter first.

  The problem is that pre - U3b vCenter 5.5 forces an SSLv3 connection when connecting to an ESXi host on port 443 (not the reverse). It does this, even if the host ESXi and vCenter SSL/TLS libraries actually support TLS 1.0 + since at least vSphere 4.0.

  So when you update one host to 5.5 U3b, the oldest vCenter again will try to force a connection SSLv3 that will fail, since SSLv3 has been disabled to the host. If you're updating vCenter, first of all, it will initiate a good TLS 1.0 + connection to more similar and updated hosts.

  Here is an explanation of the (pre - U3b) vCenter SSLv3 handshake behavior:

  Re: vCenter and host communication SSL v3

• Update Manager and ESXi 5.0 to 5.1

  Hello

  I am trying to upgrade my 5.1 ESXi host using update running 5.0u1 ESXi and vCenter 5.0u1 Manager.

  When I import the ESXi VIM ISO 5.1, I get the following error...

  Import the ESXi image
  VCENTER
  The downloaded update package cannot be used with
  VSphere VMware Update Manager.

  Any ideas?

  Thank you.

  The appropriate upgrade path is updated to vCenter 5.1 first, and then upgrade the ESXi hosts later. It was the same process for the ages with all the upgrades of version of VMware. The upgrade to vCenter is no problem (is). I can see and manage all hosts ESXi5.0U1, but prefer to use Update Manager vCenter to upgrade their 5.1 rather than on the road to CD, but there is no VIB files ' esxi 5.0-> 5.1 upgrade ' available, so nothing to import in the Update Manager.»

  It is not the end of the world, and the upgrade still works I don't know, but I would have thought this VIB would have been available when the 5.1 became available.

• 5 and update manager vCenter

  Hello

  I installed vcenter and update manager as a virtual machine host.

  Now when I want to use the update patch of the host Manager, it takes all the vm to stop.

  Obviosly if I stop the VM guests, this includes the vm vcenter himself who then stops updates.

  I tried to connect directly to the host without vcenter but then there is no Update Manager.

  Any way around this?

  Thank you

  Chris

  I would start by setting up the vmware in your main site environment - Essentials you are able to use the vmotion and HA - vmotion you will deal with the current issue - would you be able to vmotion virtual machines on a host and update without havomg yp sjut down virtual machines. With HA you will be covered in the event of hardware failure - if an ESXi host to crash the system VMs automatiically will restart on the remaining hosts.

  Bit please be aware vmotion and HA require shared storage - either SAN (iSCSI and storage FC0 or NAS/NFS -

• I have the time to default iPhone 4 iOS 7.1.2 iPhone App not updated since the last 3 days and also checked all the settings for location and also set as new iPhone always present problem... Please try to fix... Thanx

  I have the time to default iPhone 4 iOS 7.1.2 iPhone App not updated since the last 3 days and also checked all the settings for location and also set as new iPhone always present problem... Please try to fix... Thanx

  Turn off your device and turn it on again. If this does not help, sign out of your account and reconnect.

  In addition, you can try to reset your settings.

  • Press and hold the sleep/wake button
  • Press and hold the Home button
  • Press and hold both buttons until the display turns off and on again with the Apple logo on the subject.

  Alternatively, you can go to settings - general - reset - Reset all settings

• I've updated my ipad and Ive long since forgotten the HELP and the password I used now, I can't activate it. Someone at - it no clues.

  Apple. Ive updated my ipad and activate it, that ive never been asked before, I need the apple id and password that were used when I put in place. It was 8 years ago and Ive long since forgotten. Then how the * either override the need to activate deactivate or know what AID and password I was used.

  Apple seems very proud of screwing with us with updates. I hate the update whatever it is apple, I hate it. It always leads to problems. It is never easy. The one you have bright ideas?

  Are you still connected to the account anywhere so that you can look it up? Do you have the account downloads in your computer's iTunes library so that you can do "get info" on them and see the id? Have you tried: If you have forgotten your Apple - Apple Support ID ?

  If you can't find or still do not forget your id, and if you were the original purchaser of the iPad (i.e. he not was purchased used) then you could try to go to an Apple Store (make a Genius Bar appointment if you do) or try to contact iTunes Support Online (http://www.apple.com/support/itunes/contact/) and see if they can remove the iPad on the account - they are likely to want to see proof of ownership before they could help for example received original with top serial number

• I get an error 643 since April and unable to install an important update. I tried to download the update, but your instructions on the Web are very confused. It's the only update that gave me problems.

  I get an error 643 since April and unable to install an important update.  I tried to download the update, but your instructions on the Web are very confused.  It's the only update that gave me problems. Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas:

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  http://support.Microsoft.com/kb/KB976982

  You receive the error 643 0 x or 0 x 80070643 when you try to install the updates of .NET Framework by using Windows Update or Microsoft Update

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://support.Microsoft.com/kb/971058

  How to reset the Windows Update components?

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  If the above does not solve the problem, repost in the appropriate Forum:

  It's updated operating system Vista, upgraded installation and activate Forum.

  You will get the best help for any problem of Update/Service Pack in the Windows Update Forum; the link below:

  http://social.answers.Microsoft.com/forums/en-us/vistawu/threads

  When you repost here, kindly include the Error Codes, and exactly what is happening when you try to update.

  In this way, you will receive the best help.

  See you soon.

  Mick Murphy - Microsoft partner

• I have an acer 2006 copyright edition 32 bit operating system computer and each update since 2007 has no im always getting error code 8000fff and different numbers that start with Ko failed

  Windows update error codes kb937287 kb960714

  each update since 2007 has no...

  Backup of personal data (which none should be considered 100% reliable at this point) then do a format and clean install of Windows.  Please note that a repair (upgrade AKA on-site) installation will fix it!

  Once installed the clean, you will have the equivalent of a "new computer" in order to take care of everything on the next page before connecting the machine to the internet or a network otherwise and before using a USB key that is not brand new, or has not been freshly formatted:

  5 steps to help protect your new computer before going online
       http://www.Microsoft.com/protect/computer/advanced/XPPC.mspx

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• Vista Home Prem - problems since installation on 26 August updated - USB problems and everything deleted before the update restore points

  I have a Dell XPS 430 quad-processor. Receipt of the August 26 as update automatic updates. Since the computer was restarted after autoupdates, I have problems. Biggest problem is when I switch to another port my 4 ports KVM Trendnet TK - 407K and back on my Dell computer - the computer is blocked and the video is all garbled. My only recourse is to start the computer cold. After the first time it happened, I knew immediately updates, so I went in my restore points to restore back before the update. When I did restore bluescreened, but I was unable to capture data as computer restarted itself and get into the routine of starting fix. Difficulty of startup said it could not solve my problem.

  When I returned to restore to try to restore once again, I found that all my restore points have been removed. I found a utility called the shadow on the web Explorer and installed. He seems to find all my data restore point on the recovery D: drive, but Windows is not seeing them.  I should also mention, usb-wise, given that these updates have been applied, my Canon digital camera is not recognized when I hang it in one of the USB ports.

  Don't know what to do at this point. If I stay on the port on my computer using the KVM switch, my PC at home works well. Unfortunately, it is not realistic that I need to do my job in two laptops that are also connected to the switch.

  I'm tempted to just delete all the updates that have been installed on 8/26 to see if that helps - esp KB973879 I read on this patch causing a lot of problems with other computers.  Another thing that I have not tried is to use the restore from a command prompt application.

  Any suggestions would be greatly appreciated!

  Thank you!

  Hi brab61,

  Welcome to Microsoft Vista answers Forum!
   
  It is good to know that you're not faced problems with your computer.
   
  However, I suggest you go ahead and turn on Windows automatic updates to fix security vulnerabilities and it is beneficial for you to have these updates installed.
   
  Learn more about Windows Update, you can use the following link: -.
  http://www.Microsoft.com/Windows/downloads/windowsupdate/default.mspx
   
   
  You can run the System File Checker tool before you activate the automatic updates.
   
  To run the System File Checker tool, follow these steps:
  1. Click Start and type cmd in the box start the search.
  2 right click "cmd" in the list programs, and then click Run as administrator.
  3. you are asked to enter an administrator password or a confirmation, type your password or click on continue
  4. at the command prompt, type "sfc/scannow", and press ENTER.
   
  Note:- After that, you can now install an update both manually and check the update is causing the problem and let us know to help you and solve the problem.

  How to repair the operating system and how to restore the configuration of the operating system to an earlier point in time in Windows Vista
  http://support.Microsoft.com/kb/936212

  Hope this information is useful.
   
  Let me know if it worked.
  All the best!
   
  Thank you, and in what concerns:
  Divya R - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• KB951847 fails to install and I can't install the other updates since there is no.

  I tried every proposed difficulty and can not install the security updates and I can't install the other updates since there is no.  I tried the fixit, the convenience store.  I get no error number - the name of the updated and say update has failed.  I tried the fixit suggested in default and aggressive modes.  I tried stopping the service to update and it starts again.  There is no place for uncheck do not install this update.  The center of update gives me only one choice of what to put up-to-date and KB951847.  I tried to disable the start-up all elements of microsoft services and restart the computer and that did not work.  I'm out of ideas.

  Thank you.

  KB951847 is an optional, not security updates (Yes, even if it is an Important update). Feel free to hide it & move on with your life.

• My computer stopped the update since October 23, 2010, and whenever I try to check for popular update, I get the number of error code 80070490. Help, please!

  My update of the computer window stopped updating since October 23, 2010 and each time I tried check the update popular I get the error code 80070490. Help, please!

  Hello

  questions have already been addressed here in my 1st reply:

  Please read the answer given

  Here is the solution for your problem of MS

  You receive an error code "0 x 80070490" when you use Microsoft Update or Windows Update Web sites to install updates

  http://support.Microsoft.com/kb/958044

  or repost in the correct windows update forum

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-windows_update?page=1&tab=all

• Update for vsphere client and ESXi host, now getting errors

  Did a upgrade for my client vsphere, VMware-viclient-all - 6.0.0 - 3016447.exe file name

  Now I cannot view comments consoles, cannot add new guest OS (option is grayed out), and I get an error when the Client program starts (see first image)

  

  Here is the error when I try to view the console to the guest operating system. Can I use Remote Desktop connection to connect to the guest operating system (R2 for Windows Server 2012)

  

  Here is the version information

  

  Also improved the host system of the ESXi server to update to U1 using the VMware-VMvisor-Installer - 6.0.0.update01 - 3029758.x86_64.iso

  VMWare Tools never seems to complete the installation for the guest operating system.

  What can I do now?

  Client runs on a desktop computer Windows 7 Pro with 24 GB of RAM.

  ESXi is a server Dell Poweredge T110-2 with 32 GB of RAM

  I ran into the same issue and Re: VMware-viclient-all - 6.0.0 - 3016447.exe broke Console hosts 6.0 ESXi and ESXi 5.5 fixed it for me.

  André

• Need a powercli script to create a new account a local administrator on all ESX and ESXi hosts in the vcenter

  Hi all

  If someone can help me with a powercli script to create a new account a local administrator on all ESX and ESXi hosts in the vcenter, create a role called admin and give all access except the root. This shoulb be past by a virtual centre.

  Very much appreciated to help him.

  Kind regards

  MelLvin

  I suspect that you posted your question to the wrong thread

  This requires only a minor change to the script above actually.

  Something like that

  $groupName = "group"$accountName = "user"$accountPswd = "password"$accountDescription = "A user"
  
  $esxlist = Get-VMHostforeach($esx in $esxlist){    Connect-VIServer -Server $esx -User root -Password "password"
  
      Try {      Get-VMHostAccount -Id $groupName -Group -ErrorAction Stop | Out-Null    }    Catch {      New-VMHostAccount -Id $groupName -GroupAccount | Out-Null    }
  
      $rootFolder = Get-Folder -Name ha-folder-root    Try{        $account = Get-VMHostAccount -Id $accountName -ErrorAction Stop |        Set-VMHostAccount -Password $accountPswd -Description $accountDescription -AssignGroups $groupName    }    Catch{        $account = New-VMHostAccount -Id $accountName -Password $accountPswd -Description $accountDescription -UserAccount -GrantShellAccess -AssignGroups $groupName    }
  
      $rootFolder = Get-Folder -Name ha-folder-root    New-VIPermission -Entity $rootFolder -Principal $account -Role admin
  
      Disconnect-VIServer -Confirm:$false}