Non-existing connections in Cisco first LMS 4.2.4

Hello

We had strange connections in LMS 4.2.4 and earlier versions, even back at LMS 3.2.1. Even if I delete connections, they reappear as if the connection were present.

Sometimes, it is related to a change of interface of 1 G to 10G and in some cases, any other device... .but not always.

It hurts my eyes, I look at this, so I hope that some of you know the reason, or better yet, the solution.

Thanks in advance ;-)

Hello

Seems to be corrupted the database for ANI. what I would say is to reset the database to ANI.

Note: ANI database contains no historical data, reintilalizing so there won't be a problem.

the steps are:

1. stop the daemon manager

windows:NMSROOT\bin\perl.exe NMSROOT\bin\dbRestoreOrig.pl dsn=ani dmprefix=ANI

solaris\linux:

/opt/CSCOpx/bin/dbRestoreOrig.pl dsn=ani dmprefix=ANI

3 start the daemon manager to wait for 10-15 min, and then start a new DATACOLLECTIOn followed Acquistion of user tracking. Hope, he'll take care of the question please - Afroz [evaluate the useful post] *sides encourage contributors *.

Tags: Cisco Network

Similar Questions

Cisco first LMS - identity

I'm trying to configure this feature and activate the option of devices capable of identity, but there are some errors that were generated CLI commands.

After work:

Documentation:

How can I change this (before use)? I would like to remove these lines and I can't:

You seem to have tickled which seems to be a debug of the device. When you name your group of Ray, 'RADIUS' the CLI does not enter sub-mode. Change the name of Group of RADIUS to another name, and this problem should disappear.

My computer does not connect to the Internet. Event ID 7003, "the TCP/IP protocol driver service depends on the non-existent service below: IPSec."

Hello!
I am working on a Dell Inspiron 1300 laptop for a friend. She has Windows HP Home Edition, SP3 installed.
He said that Saturday night he started to act funny and wouldn't connect to the Internet. There were a few popups then begins, and he did not know if they were connected to not go on the Internet.
He had the rootkit.zeroaccess infection. I used Combofix to remove it. It won't always get on the Internet, either via a wi - fi or ethernet connection.
Looking at the event viewer, I see event ID 7003, "the TCP/IP protocol driver service depends on the non-existent service below: IPSec."
Then, event 7001, "(NLA) network location awareness service depends on the service protocol driver TCP/IP which could not start due to the following error: the dependency service does not exist or has been marked for deletion.".

I copied ipsec.sys from another XP Home machine which worked and stuck in the Windows\System32\drivers directory and it still does not work.

Any ideas are greatly appreciated!

Dave

Hello

See this link:

http://TechNet.Microsoft.com/en-us/library/cc958861.aspx

http://www.Microsoft.com/technet/support/ee/transform.aspx?ProdName=Windows+operating+system&ProdVer=5.2&EvtID=7003&EvtSrc=Service+Control+Manager&lcid=1033

Let us know the results.

my mouse can always move to a non-existent monitor screen area

I have a LG external monitor connected via HDMI. When my external monitor is turned off, my mouse can always move to the non-existent monitor screen area. Is there a way to fix this? The mouse works off the screen, that it is difficult to use. Still using Yosemite.

Unplug the cable from the screen at the end of the MAC.

How can I get rid of non-existent drive (local disk Q :) that is displayed on the screen of my computer?

original title: How do I get rid of non-existent hard disk that appears on my computer screen?

I have a local disk (q) that loads automatically on my folder "Computer" [the folder that shows all hard drives and peripheral storage removable]. The drive does not exist and when I double click above it says "Q:\\ is not accessible access is denied." I unplugged my external hard drives, and these drives disappear from the screen by this disc remains still. How can I get rid of him?

I found an article from third party in which people have found a solution:

Hide the Local disk (q) added by Office 2010 Beta

I hope this helps! (you can back up the registry first)

Change the settings of the REGISTRY can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the REGISTRY settings configuration can be solved. Changes to these settings are at your own risk

Lisa
Microsoft Answers Support Engineer
Visit our Microsoft answers feedback Forum and let us know what you think.

BlackBerry 10 account information for a non-existent account

I upgraded to one peripheral BB10 to another, and this process required me to re - enter e-mail account information. This has worked well for two email accounts that are connected to my BB, but I also got (and still get) notification 'Account Info necessary' for a non-existent account, specifically on behalf of "name1.name2. It is a corruption of an account existing '[email protected] '. In the notification, when I click on 'Open', I get the message 'Accounts', "There was a problem at the opening of your account."

How can I know my BB to stop asking information about an account that does not exist? My camera is classic BlackBerry running OS version 10.3.2.556.

Find accounts cleaner in BlackBerry World. The descriotion he describes what he does. It should help you remove these shadow accounts. The developer is on Crackberry and there is a thread on the app, if you want to simulate before using it.

Issue of integrating Cisco first Collaboration insurance LDAP

Hello

I 9.0.0 - 24376 Cisco first coverage of Collaboration with lot of fixes 3, and although I added the LDAP protocol successfully to the server of the CPCA, and when I do the connection test it gives me connection is successful with the LDAP server, then I added users to the management of the users using the same user name as the user account on the LDAP protocol and LDAP user check.

but when the user tries to connect to the CPCA using his LDAP account an error message saying that the user name or password is incorrect.

If the ideas please?

Insurance server connects with CN, not sAMAccountName in the LDAP server, make sure that you type in the user name as "John Doe" instead of jdoe. Check if it works.

Cisco first Infrastructure 2.2 API GET Interfaces

Hello

I am using Cisco first Infrastructure 2.2 and I am trying to get some info of the API in order to build a model.

But I can't find how to get the name of all the interfaces of an IP address from the device. I tried many queries, but none of them is what to expect. Is there a way interfaces?

Thank you.

Guillaume.

Hello, don't 'SE InventoryDetails' gives you what you need? I believe you can use the features of REST to filter down to only the devices you are interested.

Existing connection had to be closed by the remote host

Need help with this error

I have a dev and a uat environment.

I have a small form that I use as a method to call a web service. Essentially, the form contains a web service URL text box.

If I call the shape on the dev and pointer to the service web dev, it works.

If I use the form on uat and point the service web uat it works.

If I use the form on UAT and call the web service on dev, it works.

However, if I use the form on the dev and point the web service uat I get this error:

In the Application Server error ' / '. An existing connection was to be closed by the remote host Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and its origin in the code.

Exception details: System.Net.Sockets.SocketException: An existing connection was to be closed by the remote host

Source error:

The source code that generated this unhandled exception can only be shown when compiled in debug mode. To do this, follow one of the below steps, then request the URL:

1. Add a "Debug = true" directive at the top of the file that generated the error. Example:

<%@ Page Language="C#" Debug="true" %>

or:

(2) add the following section to the configuration file of your application:

Note that this second technique, all the files in an application to be compiled in debug mode. The first technique will make only this file to be compiled in debug mode.

Important: Running applications in debug mode causes a memory/performance load. You must ensure that an application has debugging disabled before deploying to the production scenario.

Stack trace:

[(0 x 2746) SocketException: an existing connection was to be closed by the remote host] System.Net.Sockets.Socket.Receive (Byte [] buffer, Int32 offset, Int32 size, SocketFlags socketFlags) + 73 System.Net.Sockets.NetworkStream.Read (Byte [] buffer, Int32 offset, Int32 size) 131 [IOException: unable to read data from the transport connection: an existing connection was to be closed by the remote host.] System.Net.Sockets.NetworkStream.Read (Byte [] buffer, Int32 offset, Int32 size) + 294 System.Net.PooledStream.Read (Byte [] buffer, Int32 offset, Int32 size) + 26 System.Net.Connection.SyncRead (request of HttpWebRequest, Boolean userRetrievedStream, Boolean probeRead) + 297 [WebException: the underlying connection was closed: an unexpected error occurred during the reception.] System.Net.HttpWebRequest.GetResponse () + 5399741 _Default.btnTestUpload_Click (Object sender, EventArgs e) + 532 System.Web.UI.WebControls.Button.OnClick (EventArgs e) 111 System.Web.UI.WebControls.Button.RaisePostBackEvent(String eventArgument) + 110 System.Web.UI.WebControls.Button.System.Web.UI.IPostBackEventHandler.RaisePostBackEvent (String eventArgument) + 10 System.Web.UI.Page.RaisePostBackEvent (IPostBackEventHandler sourceControl, String eventArgument) + 13 System.Web.UI.Page.RaisePostBackEvent (NameValueCollection postData) + 36 System.Web.UI.Page.ProcessRequestMain (includeStagesBeforeAsyncPoint, Boolean, Boolean includeStagesAfterAsyncPoint) 1565

Version information: Microsoft .NET Framework Version: 2.0.50727.4234; ASP.NET Version: 2.0.50727.4223

Any ideas?

Hello

I suggest you for this post in the appropriate section of the form of MSDN

http://social.msdn.Microsoft.com/forums/en-us/categories/

I hope this helps.

Non-existent devices USB not recognized

We get the message that USB device not recognized on several machines (Dell Optiplex 980) with XP and the same type of machines with Windows 7. The only USB devices that are attached to the machine are the keyboard and the mouse and the two are identified by the system and are working properly. Mention all the answers that I can find for similar questions about errors for non-existent devices. Can anyone help? Thank you

No card reader. I submitted this to Dell as the system is a Dell Optiplex 980 and they said that the problem may be with the motherboard that needs to be reset. I tried to unplug the PC from the wall, but that has not solved the problem. They sent a technician with a new motherboard. That did not help. When downloading all the drivers I could find, I noticed that the monitor was turning and all by itself. Also noticed that we had a USB2 cable connection of the monitor to the computer to activate the USB port that is built into the monitor. When I pulled the usb2 to the monitor cable, the error has disappeared and when I plugged it in the returned error. I have this will report to Dell, but in the short term, the problem is resolved.

I have a serial number and product code the product disc, but cannot download my Adobe Photoshop CS6 on my Macbook Pro. All the instructions say "double-click install.app" but this seems to be a non-existent option on my computer. I even bought a Super

I recently bought a Macbook Pro and can not download my Photoshop CS6 extended. I have a serial number and product code the product disc, but, but still am not able to download my product. All the instructions say "double-click install.app" but this seems to be a non-existent option on my computer. I even bought a drive USB superdrive for the sole reason to put in my product directly drive download and it does not work either.
I also tried to install directly from the site Web Adobe - my serial code was denied, but I only used it on my old laptop, so it is supposed to work again.
It seems equally clear that Adobe did the download of older products as difficult as possible for past clients. This is ridiculous. I spent hours trying to get this to work and have gotten nowhere. Does anyone have advice for me?

It is not known if you encounter a problem downloading or installation problem, but it looks to be an installation problem.

If it's really a problem downloading, file links are below.

Available downloadable Setup files:
- Suites and programs: CC 2014 | CC | CS6 | CS5.5 | CS5 | CS4, CS4 Web Standard | CS3
- Acrobat: DC | XI, X | 9,8 | 9 standard
- First Elements: 13 | 12 | 11, 10 | 9, 8, 7
- Photoshop Elements: 10, 11, 12, 13. 9,8,7
- Lightroom: 6| 5.7.1| 5 | 4 | 3 | 2.7 (win),2.7 (mac)
- Captivate: 8 | 7 | 6 | 5
- Contribute: CS5 | CS4, CS3
Download and installation help links Adobe

Help download and installation to Prodesigntools links can be found on the most linked pages. They are essential; especially steps 1, 2 and 3. If you click on a link that does not have these listed steps, open a second window by using the link to Lightroom 3 to see these "important Instructions".

window using the Lightroom 3 link to see these "important Instructions".

Support SQL parameters and a non-existent column
Using the concept of dataset in SSRS I run the SQL code below for different servers. (CH_PRD, LA_PRD, FL_PRD). When I say servers it's connections. If all these connections have the same tables, views, objects... etc with slight variations. These are the databases of our different entities.

CH_PRD and FL_PRD a column 'NET_AMT' and 'TAXABLE_AMT', but LA_PRD has not. So, I get 'SF. TAXABLE_AMT' is an invalid identifier (makes sense because these columns do not exist in LA_PRD) when I run this for LA_PRD. SO is there a way to fix this please help me guys. Thanks in advance.
```
SELECT 
 Account,
 CASE WHEN :Server= 'LA_PRD' THEN NULL ELSE SF.NET_AMT END AS NET_AMT,
 CASE WHEN :Server= 'LA_PRD' THEN NULL ELSE SF.TAXABLE_AMT END AS TAXABLE_AMT

  
FROM CIRC_RPT.VW_SUBS_FINANCIAL_DRW SF
```
Published by: varun on March 13, 2013 10:37
>
Using the concept of dataset in SSRS I run the SQL code below for different servers. (CH_PRD, LA_PRD, FL_PRD). When I say servers it's connections. If all these connections have the same tables, views, objects... etc with slight variations. These are the databases of our different entities.

CH_PRD and FL_PRD a column 'NET_AMT' and 'TAXABLE_AMT', but LA_PRD has not. So, I get 'SF. TAXABLE_AMT' is an invalid identifier (makes sense because these columns do not exist in LA_PRD) when I run this for LA_PRD. SO is there a way to fix this please help me guys. Thanks in advance.
>
You need create this query string dynamically, and then submit the completed to process query string.

You can not submit a query that includes a non-existent column to the database.
```
String query;

if (Server.equalsIgnoreCase('LA_PRD') {
  query = 'SELECT Account, NULL NET_AMT, NULL TAXABLE_AMT FROM CIRC_RPT.VW_SUBS_FINANCIAL_DRW SF';
}
else {
  query = 'SELECT Account, SF.NET_AMT, SF.TAXABLE_AMT END AS TAXABLE_AMT FROM CIRC_RPT.VW_SUBS_FINANCIAL_DRW SF';
```

Force evaluation of the rules for the non-existent entities and unknown attributes...
Hi all

I have another issue potentially easy for the gurus of the OPA in this forum - there must be a simple explanation to this question but I'm just not see it.

The problem that I am having with several of my rules, it's that the conclusion is not evaluated due to the non-existent entity instances or unknown entity attributes. As an example of the first scenario, I have a rule that checks for the existence of an instance of an entity with a type and status. The conclusion is evaluated as if there is at least an instance of this entity, otherwise, the conclusion remains unknown.

Similarly, I wrote an equation to annualize all its (financial) obligations in a case, where the frequency of the obligation can be weekly, fortnightly, monthly, etc.. I created an attribute for each type of frequency, which are then added to the equation. The issue in this example, is that the equation does not conclude if there is not a value for each attribute in the equation. For example, if:

assign 1 = A + B + C

where A = 1, B = 2 and C is unknown, does not examine the attribute from 1 to 3, but will remain unknown. Logically, I expect that the lack of a digital defaults to 0, and rather unknown attribute value, but this is not the case.

I looked at the 'Certain and known operator rule examples' help topic to try to understand how assign a value to an unknown attribute, but the example at the bottom of the topic page does not provide a sufficient explanation as to how the logic:

point of the total team = team 1 round points + points of the round 2 team + team of turn 3 points

the team of the round 1 points = 0 if
Round 1 team points (such as recorded by the team) is unknown

the team from round 2 points = 0 if
etc.

It seems from the example that there are 2 attributes used to the same variable: [team of the Tower, 1 points] and [team of the round 1 points (such as recorded by the team)]. It is not clear to me how the original equation can be concluded if the values are stored in the alternate attribute [points of the round 1 team (such as recorded by the team)] etc.

I have also considered using fragments of rule by the help topic "Prove an attribute using multiple rules", while I could use two equations separated to set the value of an attribute according to the circumstances, that is to say:

assign 1 = A + B + C

1 = 0 if attribute
attribute 1 is unknown

This attempt results in a logic loop error, probably because I am trying to set the value of an attribute based on the same attribute value.

Any help will be greatly appreciated!
Philippe
Hi Philippe,.

I suggest the following way to solve this problem, although there are other ways too.
You can use a table of rules for it.

Open a Working Document, and then press 'Alt + Z' created a rules table.

Use the following rule: -.
Keep the text in bold in the left-hand column and the text in italics as a condition for the title in the right column. Use a correct indentation during the compilation of the rules.

-------------------------------------------
Attribute 1
-------------------------------------------
*0*     any
A is unknown or

Uncertain East
and
any
B is unknown or
B is uncertain
and
any
C is unknown or
C is uncertain
----------------------------------------------
Has any
B is unknown or
B is uncertain
and
any
C is unknown or
C is uncertain
----------------------------------------------
A + B C is unknown or
C is uncertain
-----------------------------------------------
A+B+C in the opposite case

Thank you
Sofiane

Try the following: where is my profine stored? It will take you to non-existing buttons etc. It is for the most part iof support.

This is a general problem: 'help sysytem' structure has been changed (perhaps in part I dion can't Koe) then the flow of questions from the ends up to non-existent (existing is more..) tips, suggestions, or instructions set how, not more existing or operating.
Very frustrating.
I raise my profile under Linux on the terminal with something like "find - name *.mab"and got it in a split second." None of the ways suggested later in the help worked!
This is a general question for site designers, thanks for help [actually: it's the Help menu...]. Welcome,
Giancarlo.
Please follow the trail of help: you will get what I say, sorry. g.

@Zenos. Thank you very much for your screenshot, which solved the issue.
I have a Tundebird for Linux version, which, as far a s I see, is somewhat different from what you have. The previous version had not all submenus as you show, however, he recent update I made 'my' Thunderbird earned him almost to what you posted simply we had different programs.
I suggest that it closed the thread. Thaks to all to help.
Giancarlo.

Droid Turbo could not connect the Cisco access point

Greetings.

Since the upgrade to a droid turbo, I was unable to connect to the network without wire of my work. I work in the it Department, but my experience with Cisco technologies and wireless is limited, so I tried to understand why. My previous bike x worked fine. We have a network of all the access points managed by a controller Cisco 4402 running version 7.0.98 of the BONES. I was able to connect to another wireless network that I could meet outside of work, and I am able to connect to the network of my work if I connect it is unsecured guest SSID. Only connections to our 4 secure networks fail. The controller reports that my phone cannot all simply to authenticate. The controller is configured for WPA2 / AES using a key 284 on the particular network, that I am trying to connect. I entered this key manually both via copy and paste. As far as my phone goes, I only tried to withdraw and time networks like tent to start it in safe mode without success. I read on various forums android that maybe it's a problem related to Kit Kat and this kind of problem has appeared on other handsets from other manufacturers, but nothing definite.

Any suggestions would be much appreciated.

-Josh

Let me direct you to two other discussions here on the Droid Turbo forum and the other from Cisco which may help.

Unable to connect to company wifi

https://forums.Motorola.com/posts/af633eb3e4

DROID WiFi Turbo questions

https://forums.Motorola.com/posts/06a2f3c5ca

Connectivity issues with Cisco and Moto X (Gen 2) allowed RMC controllers (probably related)

https://supportforums.Cisco.com/discussion/12331486/connectivity-issues-Cisco-controllers-and-PMF-enabled-Moto-x-Gen-2

I hope this helps!

Non-existing connections in Cisco first LMS 4.2.4

Similar Questions

Maybe you are looking for