Not tagged and VLAN

Similar Questions

• The strength of uplinks not tag with VLAN

  I have a very strange config due to the servers being located in the same place. I have 2 of my server (s) uplinks an uplink is connected to a switch under my control. the first uplink is connected to my stwichand that the port is crimped tagging vlan. The second uplink is connected to the network from my ISP to a port without a label.

  I want my switch activates the NIC conencted and the card network connected to the ISP to be on standby. The problem is that I have to tag the traffic from my VM so when it switches to my ISP network port without tag removes all traffic. Conencted to my ISP port is for failover only.

  one solution is to create a second group of ports on a dedicated vswitch which has no tagging vlan and manually connect the VM to present portgroup failure.

  Ideally, I would like to make it automatic, is it possible to automate the above solution? or to force all traffic through a specific untagg traffic vmnic?

  Then, I enclose a diagram of what I understand from your network environment.  Please check if it is correct or not.  If this is the case, then you have an interesting situation that I think could be solved with comments e1000 NIC; shift of grouping; and perhaps of multiple itineraries, weighted by default.  All in the comments.

  The changes would have to occur in the comments, if the network it will access your ISP (0.0.z.0/24) is a different subnet subnets on your switch.

  Virtualization of happy!

  JP

  Please consider awarding points for correct or helpful answers.

• With the help of VLANS and VLAN Tagging is not working / no connection

  Hello

  I m trying to configure a VLAN between some virtual machines on ESX host 3.

  I want to do this way:

  http://KB.VMware.com/selfservice/microsites/search.do?language=en_US & cmd = displayKC & externalId = 1004074

  I got 1 dedicated NETWORK adapter to each ESX host that is connected to a dvSwitch in which I configured a portgroup

  with VLAN ID 2121. I have configured each virtual machine to use this network.

  When I put the virtual machines on a single host, they are able to communicate.

  When they are placed on different hosts they are (if the VIRTUAL LAN is enabled on portgroup) not able to communicate.

  So I m assuming it must be a problem in the config NIC on the ESX host or switch.

  I m using a HP2910AL on which I activated mode trunk for each port that is connected to a NETWORK card with

  the dvSwitch/Portgroup I try to use for the vlan. In the hp switch, I have a default VLAN with ID 1 where

  the Ports are marked not signposted. I install a second VLAN on the switch with ID 2121 in which I scored

  This tag ports.

  Is there something else to do - perhaps side ESX host?

  I tried changing the settings as "forged transmission-> allow ' on portgroup and I found other things

  in the web, but always without success.

  Kind regards

  Patrick

  Were you referred to this guide? :

  http://CDN.ProCurve.com/training/manuals/2910-ATG-Feb09-2-VLAN.PDF

  "show vlan ports" would be my next check to make sure that you have connected to your ESXi host 3 ports in the vlan 2121.

  As Duncan has said if you have a VLAN ID on the portgroup in the vSwitch and you have the port on the pSwitch as trunk not acess and VLAN ID is allowed on the trunk port pSwitch you should be ok.  Just to clarify the trunk is 802. 1 q No 802.3ad.

  The reverse is not VLAN ID on the portgroup vSwitch, use coelio on pSwitch with VLAN ID.  Limited pSwitch port to a VLAN, this may be ok for you?

• Tagged management VLAN and the virtual machines on the same VLAN

  I'm faced with a problem related to our Brocade switches newly acquired and get the private VLAN to work on trunk connections to our ESX servers.  Every time I try something different, he creates a new problem.

  In our configuration, our management of VLAN is not tag and we have a VLAN for this management network that is placed on our switches VLAN no marked native.  We also have virtual machines hosted on those same ESX servers that are on the same VLAN and everything works fine.  However, when I change the ESX management to carry a label on this VLAN and change the switchports accordingly (IE no untagged VLAN native), management work, but hosted on the ESX Server machines that are on the same VLAN can get no network connectivity.

  Is it possible to have a management network labeled and also the host of virtual machines on the same VLAN or is it totally impossible?  I'm not very familiar with networking behind ESX, so I apologize if this is a dumb question with an obvious answer.

  Thank you

  Mark J.

  Is it possible to have a management network labeled and also the host of virtual machines on the same VLAN or is it totally impossible?

  Yes, it is possible... why it doesn't work for you I don't know, but try the following:

  1. set up the Group of ports of VMS to use VLAN;

  2 configure the interface of management VMkernel port group use VLAN;

  3 configure the physical switch port to allow to this VLAN and put the default VLAN natively for these interfaces.

• VLAN Tagging (VST) and VLAN native on the same vswitch

  I'm trying to figure out if its possible to put running the VLAN tagging for a vswitch if our virtual machines are currently in the vlan 1 (vlan native) on our cisco switches. I don't know why it's set up this way, but change is not an option at this time.

  Ultimately what I'm trying to accomplish is setting up a group of servers that differ on one VLAN, but under the same vswitch. I'm assuming that VST is what I need, but I don't know if I can simply specify how vlan 1 as the vlan 1 is not marked on cisco switches and my understanding is that VST requires to carry a label.

  Your help is greatly appreciated.

  NuRD.

  With the vSwitch connected to a trunk on the physical switch port, create the port groups and you need only configure the ID then VLAN for the port groups that do not use of VLAN native. See for example http://kb.vmware.com/kb/1004074

  André

• Tags and Notes in a single CSV file export

  I'm trying to export tags and notes in to a CSV simple change of batch and importation in vCenter.  I have a script to export tags and I can export notes, but I want to make in a single operation and to a simple CSV file.  Here's the current code, I use and please forgive me for not crediting the original creator, I built this script I don't remember!  I have a Notes column in the CSV file resulting, but he is empty...  Thanks in advance.

  Don

  Current script:

  If (-not of $DefaultVIServer.IsConnected) {}

  SE connect-VIServer "vcenter.server" - Credential (Get-Credential $_.) User name)

  }

  $tagCat = @)

  $tagTab = @ {}

  foreach ($tag in (Get-TagAssignment)) {}

  $tagCat += $tag. Tag.Category.Name

  $key = $tag. @entity.name

  {if ($tagTab.ContainsKey ($Key))}

  "$val = $tagTab.Item ($key)"

  }

  else {}

  $val = @ {}

  }

  $val. Add ($tag. Tag.Category.Name, $tag. Tag.Name)

  $tagTab [$key] = $val

  }

  $tagCat = $tagCat | Sort-Object-Unique

  $tags = foreach ($row in ($tagTab.GetEnumerator () |)) Sort - Object - property key)) {}

  $VMName = $row. Key

  $VMNotes = get - VM $VMName | Select-Object - ExpandProperty Notes

  $obj = new-Object-property PSObject @ {}

  Name = $row. Key

  }

  $tagCat | %{

  $obj | Add-Member-Name $_-value $row. Value [$_]-MemberType NoteProperty

  }

  $VMNotes | %{

  $obj | Add-Member-name 'Notes' - value $row. $VMNotes - MemberType NoteProperty

  }

  $obj

  }

  $tags | Export Csv tags.csv - NoTypeInformation - UseCulture

  Try like this

  If (-not of $DefaultVIServer.IsConnected) {}

  SE connect-VIServer "vcenter.server" - Credential (Get-Credential $_.) User name)

  }

  $tagCat = @)

  $tagTab = @ {}

  foreach ($tag in (Get-TagAssignment)) {}

  $tagCat += $tag. Tag.Category.Name

  $key = $tag. @entity.name

  {if ($tagTab.ContainsKey ($Key))}

  $val = $tagTab.Item ($key)

  }

  else {}

  $val = @ {}

  }

  $val. Add ($tag. Tag.Category.Name, $tag. Tag.Name)

  $tagTab [$key] = $val

  }

  $tagCat = $tagCat | Sort-Object-Unique

  $tags = foreach ($row in ($tagTab.GetEnumerator () |)) Sort - Object - property key)) {}

  $VMName = $row. Key

  $VMNotes = get - VM $VMName | Select-Object - ExpandProperty Notes

  $obj = new-Object-property PSObject @ {}

  Name = $row. Key

  }

  $tagCat | %{

  $obj | Add-Member-Name $_-value $row. Value [$_]-MemberType NoteProperty

  }

  $obj | Add-Member-name 'Notes' - $VMNotes - MemberType NoteProperty value

  $obj

  }

  $tags | Export Csv tags.csv - NoTypeInformation - UseCulture

• Bootdhcprelay and VLAN 6224

  Hi, I searched the forum and found a lot of help with this problem. I have 3 VLANS configured on my PowerConnect 6224 and a DHCP Server Windows Server 2000 with different subnet scopes, as far as I know that I need to put in place a bootdhcprelay server and activate bootdhcprelay what I did, but when I try to get a my client pc dhcp address I do not get an address. When I configure the client with a manual IP address, I can communicate as expected.
  Here's my running-config, is there anything wrong?

  ! Current configuration:
  ! Description of the system 'Dell 24 ports Gigabit Ethernet, 2.0.0.12, VxWorks5.5.1'
  ! Version of the software system 2.0.0.12
  ! Configure the vlan database
  VLAN 10,20,30,40
  subnet of VLAN association 10.10.1.0 255.255.255.0 1
  subnet of VLAN association 10.10.10.0 255.255.255.0 10
  subnet of VLAN association 10.10.20.0 255.255.255.0 20
  subnet of VLAN association 10.10.30.0 255.255.255.0 30
  subnet of VLAN association 10.10.40.0 255.255.255.0 40
  output
  hostname "L3_Switch".
  1 1 stackmember
  output
  1 priority 1 switch
  10.10.1.1 IP address 255.255.255.0
  IP default-gateway 10.10.10.2
  IP - XXXX domain name
  name-server IP 10.10.10.10
  IP routing
  IP route 0.0.0.0 0.0.0.0 10.10.10.2
  bootpdhcprelay enable
  bootpdhcprelay IP_serveur 10.10.10.10
  helper-address 10.10.10.1 IP 10.10.10.10 37
  helper-address 10.10.10.1 IP 10.10.10.10 49
  helper-address 10.10.10.1 IP 10.10.10.10 137
  helper-address 10.10.10.1 IP 10.10.10.10 138
  helper-IP 10.10.10.10 address 255.255.255.0 37
  helper-IP 10.10.10.10 address 255.255.255.0 42
  helper-IP 10.10.10.10 address 255.255.255.0 49
  helper-IP 10.10.10.10 address 255.255.255.0 53
  helper-IP 10.10.10.10 address 255.255.255.0 137
  helper-IP 10.10.10.10 address 255.255.255.0 138
  10.10.20.1 helper-address IP 10.10.10.10 37
  10.10.20.1 helper-IP 10.10.10.10 address 49
  10.10.20.1 helper-address IP 10.10.10.10 137
  10.10.20.1 helper-IP 10.10.10.10 address 138
  10.10.30.1 helper-address IP 10.10.10.10 37
  10.10.30.1 helper-IP 10.10.10.10 address 49
  10.10.30.1 helper-address IP 10.10.10.10 137
  10.10.30.1 helper-IP 10.10.10.10 address 138
  10.10.40.1 helper-address IP 10.10.10.10 37
  10.10.40.1 helper-IP 10.10.10.10 address 49
  10.10.40.1 helper-address IP 10.10.10.10 137
  10.10.40.1 helper-IP 10.10.10.10 address 138
  interface vlan 10
  name "Main_Production".
  Routing
  IP 10.10.10.1 255.255.255.0
  output
  interface vlan 20
  name "Vlan_2".
  Routing
  IP 10.10.20.1 255.255.255.0
  output
  interface vlan 30
  name "Vlan_3".
  Routing
  IP 10.10.30.1 255.255.255.0
  output
  interface vlan 40
  name "Vlan_4".
  Routing
  IP 10.10.40.1 255.255.255.0
  output
  level of 4f70cfb1451a1b0ce0b872421bee6c1c user name 'admin' password encrypted 15
  the IP dhcp filtering
  !
  interface ethernet 1/g1
  switchport mode general
  pvid switchport General 10
  No switchport acceptable-framework-type general tag only
  VLAN allowed switchport General add 10,20,30,40
  output
  !
  interface ethernet 1/g2
  switchport mode general
  switchport General pvid 20
  No switchport acceptable-framework-type general tag only
  VLAN allowed switchport General add 10.20
  output
  interface ethernet 1/g3
  switchport mode general
  switchport General pvid 30
  No switchport acceptable-framework-type general tag only
  VLAN allowed switchport General add 30
  output
  !
  interface ethernet 1/g24
  switchport mode general
  pvid switchport General 10
  No switchport acceptable-framework-type general tag only
  VLAN allowed switchport General add 10,20,30,40
  output
  output

  Please tell me if you find errors.

  
  

• Create 2 VLAN (VLAN 1 and VLAN 2)

  Hi all

  I need help and advice with my new Cisco SF300-48. I want to create 2 vlan (vlan 1 and vlan 2). The switch is set at layer 2.

  example:

  VLAN 1 (port 1, 2, 3), vlan 2 (port 4, 5, 6)

  VLAN 1 can communicate with each other (port 1, 2, 3) and vlan 2 can communicate with each other (port 4, 5, 6)

  But vlan 1 cannot communicate with vlan 2.

  Any help would be appreciated

  Thank you

  Johan

  Well, as far as I understand the message communication between the VLAN is not necessary. The thing is, that all ports LAN VIRTUAL (for example VLAN 1 with ports 1, 2, and 3) cannot communicate with each other. Did you check the configuration of the port / VLAN (VLAN configured to each port configuration right / right about the tag-no identified)?

• POS and vlan

  Initial conditions:

  NET 172.30.157.0/24 with vlan 3032.

  I try to deploy Vmware DataProtection 6.1.1.

  Deploy device with vCenter and configuration of the network settings.

  

  After the restart the system in the virtual machine does not work because VLAN is not set up

  

  Configure the vlan according to manual http://www.UNIX.com/man-page/SUSE/5/ifcfg-VLAN/

  Parameters of comment in/etc/sysconfig/network/ifcfg-eth0:

  #IPADDR = '172.30.157.110'

  #NETMASK = "255.255.255.0" "

  Create new config for vlan /etc/sysconfig/network/ifcfg-eth0.3032

  STARTMODE = 'auto '.

  ETHERDEVICE = "eth0".

  ID_VLAN = '3032'

  IPADDR = '172.30.157.110'

  NETMASK = "255.255.255.0" "

  BROADCAST = '172.30.157.255'

  Restart the virtual machine and test that network will work:

  root @(None): ~ / #: ping 172.30.157.110

  PING 172.30.157.110 (172.30.157.110) 56 (84) bytes of data.

  64 bytes from 172.30.157.110: icmp_seq = 1 ttl = 64 time = 0,061 ms

  64 bytes from 172.30.157.110: icmp_seq = 2 ttl = 64 time = 0,037 ms

  64 bytes from 172.30.157.110: icmp_seq = 3 ttl = 64 time = 0.024 ms

  Network is working. But the console shows that the network does not work.

  

  Check the roads:

  root @(None): ~ / #: route ip

  by default via 172.30.157.254 dev eth0.3032

  127.0.0.0/8 dev lo scope link

  169.254.0.0/16 dev eth0.3032 scope link

  172.30.157.0/24 dev eth0.3032 proto kernel scope link src 172.30.157.110

  root @(None): ~ / #: route

  Kernel IP routing table

  Destination Gateway Genmask Flags metric Ref use Iface

  by default 172.30.157.254 0.0.0.0 UG 0 0 0 eth0.3032

  Loopback * 255.0.0.0 U 0 0 0 lo

  link-local * 255.255.0.0 U 0 0 0 eth0.3032

  172.30.157.0 * 255.255.255.0 U 0 0 0 eth0.3032

  Enter at the https://172.30.157.110:8543 / vdp - configure / and see the perfect situation:

  There are fields with netowork empty setting and there is not the label of fields

  

  Fill in all the fields? but they are red and nobody presses the button "next".

  

  Change the network setting in the/etc/sysconfig/network/ifcfg-eth0 and restart:

  IPADDR = '172.30.157.110'

  NETMASK = "255.255.255.0" "

  BROADCAST = '172.30.157.255'

  After the reboot the network does not, although VM ping of the network 'outside '.

  

  Look at the roads. There are two identical courses for different interfaces:

  

  Remove the road to eth0

  IP route del 172.30.157.0/24

  

  Enter at the https://172.30.157.110:8543 / vdp - configure /

  Now, the page is correct and the 'next' button is prerssed.

  

  After installation complete wizzard, I have a few problems:

  -root password does not change

  -integration with vcenter was not held

  -network windows do not work, because hadou presents two routes identical defferent from the network interfaces

  How can I configure POS with VLAN?

  PS: Sorry for my English.

  Hello

  Why try you tag VLAN in the unit?

  Why you do not configure the VLAN to the portgroup to map network application uses?

  Tim

• Existing vSwitch using and VLAN

  Hello

  I was wondering if it was possible to configure Lab Manager to use an existing vSwitch and VLANS configured in vCenter rather than create its own switch and VLAN?

  Thank you.

  Unfortunately not.  You will need to let LM create and manage their own groups of ports or switches.

  Note that:

  -When you bind a physical network to a vSwitch/vDS, LM creates a port group to represent the network (it also has an 'LM' tag in vCenter)

  -If you deploy a configuration "reserved", he made a vSwitch or vDS port group to represent the fence... and limit network traffic.  Again, when you look in vCenter, there should be an 'LM' tag to the object.

  Kind regards

  Jon Hemming, b.SC., RHCT, VMware vExpert 2009
  http://Twitter.com/vJonHemming

  If your question or problem has been resolved, please click the "right answer".  If someone helped him, please click "useful answer.

• Question about VMKernel iSCSI traffic and VLANS

  Hello

  This is a very fundamental question that I'm sure I know the answer too, but I want to ask him anyway just to reassure myself.  As a precursor to my question, the configuration of my ESX infrastructure is best described here: http://www.delltechcenter.com/page/VMware+ESX+4.0+and+PowerVault+MD3000i.  Or more precisely, we have two controllers MD3000i.  Each controller has two ports and each port is configured on two different subnets, with every subnet connected to the different switch.  ESX host are connected to two switches.  The only difference for the guide, is we have two MD3000i configured the same, connection to the same switches.  Each MD ports is configured on the same subnet, but different IP addresses.

  At present, we are in the process of upgrading our two iSCSI switches of humble Dlink DGS - 1224T to Cisco 2960 T of.  The switches have been and continue to be dedicated to iSCSI traffic, however, I'm trying to set up VLAN s on the side of the switch.  Originally, we used the default VLANS on switches, however, after you have added an another MD3000i, noted the Support Dell best practices is to separate each on its own subnet and VLAN MD3000i iSCSI traffic. This would result in iSCSI 4 VLANS, two on each switch and two for each MD3000i.  Firstly, is this in fact of good practices?

  Second, if I migrate preceding 4 iSCSI VLANS, as each switch port will actually be an access port, will there need to complete the VLAN ID field in the VMKernel configuration page? Presumably, this field is used when the tagging VLAN is used, but as our switches do not need any other rocking trunk (as they are dedicated to iSCSI traffic), there should be no need to fill?  I guess it would be prudent to keep the two existing subnets, create two new subnets and make changes to an MD3000i and connection of the ESX host.  Provided the switch and switch ports has been appropriate configured with VLAN on the right, the rest should be transparent and he wouldn't be Intel VLAN in all ESX hosts?

  Would be nice to get answers and thank you in advance!

  Gene

  (1) Yes, it is best practice for ESX iscsi, having an independent network and vlan for iscsi traffic.

  (2) No, there is no need to mention anything in the area of vlan, if you use an access port. Its a mandatory thing than a choice. If you supply the id vland with access port, it loses connectivity.

  Please explain a bit why you need to create two different virtual local networks for each MD3000i. You are going to use several on the same ESX box iscsi storage? Alternatively, you use only a single iscsi and use these 4 ports for the same single VMkernel interface?

  NUTZ

  VCP 3.5

  (Preparation for VCP 4)

• My tags and filters disappear when I migrate to another computer. How to get those back?

  I use Thunderbird to work, and I need to use several computers (desktop and laptop - Mac). I was able to successfully migrate everything by copying the profile folder, but the tags and filters exceed. The address book either, but I just use the import/export for this tool. I crept over all files filter, but it still does not. I manually create tags, but when I mark an e-mail on one computer, it won't label it on the other.

  Thank you, Diego. It turns out that the module does not work with the latest version, but this one does: https://addons.mozilla.org/en-US/thunderbird/addon/tb-import-export-wind-li-port/?src=search

  I installed it and it picked up my filters and my color labels.

  Thank you!

• Somehow the tag and search bookmarks in Safari?

  I imported all my favorites from Firefox. I lost all my tags and smart folders. Is there a way to mark or to search my favorites?

  Click the icon to the sidebar top left of the toolbar of Safari.

  Right below where you see this:

  

  Simply type your bookmark search keywords in the search field.

  Unfortunately, it is not possible to tag Safari bookmarks, but you can create a folder of bookmarks in the bookmarks menu and then add bookmarks in this folder, and then drag this folder on the desktop. The Finder with automatically alphabetize bookmarks, then drag that folder back to Safari.

• I want to sort my favorites by the introduction of new tags and to move the bookmarks in different tags; How can I do this?

  I recently bought my mac mini and I created my Firefox, but I do not see how to set up a new tags and ten move my favorites in the categories of the tag

  See:

  • https://support.Mozilla.org/KB/bookmark+tags
  • https://support.Mozilla.org/KB/sorting+bookmarks
  • http://KB.mozillazine.org/Sorting_and_rearranging_bookmarks_-_Firefox
  • SortPlaces: https://addons.mozilla.org/firefox/addon/sortplaces/

• Dell Inspiron 1501 wireless light is not on and I can't get a wireless connection. Dell Inspiron 1501 wireless light is not on and I can't get a wireless connection.

  Dell Inspiron 1501 wireless light is not on and I can't get a wireless connection. I was told that I needed to press the Fn key and F2 but it doesn't change anything

  Catherine,

  To press Fn and F2, you must have installed Dell QuickSet.

  Places to look to see if your connection is activated

  Did you recently install/reinstall the operating system, have you installed the desktop system software / laptop (as appropriate) and drivers from the chipset first? If this is not the case, the rest of the drivers will not install. How to download and install drivers in the correct order

  Start with the computer system software and the chipset drivers and follow the list.

  Go to the drivers & downloads , enter your service tag, and then select your operating system. Under applications, you can find Dell QuickSet.

  Rick