Of aircraft received fatal alert EUC access point: handshake_failure.

Similar Questions

• Receiving the message "Wireless association failed because Windows did not receive response from the access point or wireless router" _

  My laptop was working fine yesterday, but when I started it today I get the message "Wireless association failed because Windows did not receive response from the access point or wireless router.

  I can see my network and I can connect to the internet using my desktop pc, but just to make complicated I can't even connect to the network when I plug the ethernet cable into my laptop.

  I think it might be a driver problem, but I have no idea how to solve this problem without access to the internet on my laptop.

  I'm running Vista and my wireless router is an Atheros AR5009 809.11a/g/n

  I need step by step instructions on this Yes please treat me like a fool!

  Thank you

  Laptop would not work at home thus concluded that it was a BT Broadband do not issue my driver (despite BT telling me the opposite last night)

  After the call to a fantastic Lady in BT it's all fixed and thanks to Jack I now know a lot more on connecting wireless to my laptop!

• EUC Access Point problem

  Hello!

  I'm testing the New Horizon 7 with EUC Access Point (AP) (euc-access-point - 2.5.0.0 - 3588605_OVF10).

  I deployed configuration "1 NIC" PA Finally, when I open https://AP-FQDN I did have an error 'no page displayed'.

  Has anyone already deployed the AP?

  Finally, I coped with it!

  The newspaper said that my password for root violated the requirement...

• Wireless connection failed because windows did not receive response from the access point or wireless router

  Monday Nite I downloaded a driver site HTC syn my Android Hero phone. After extracting and installing the driver in the zip file, I tried to sync with my phone which was hook up my laptop. It did not work. Interrupt the synchronization process and I tried to check my email from outlook. Found it cannot send and receive mail. Open my browser and found that it disconnected. And so, using the LAN cable, fortunately, it worked. So I wonder what is happening to my function wireless on my laptop?

  Can someone tell me what I need to do? Thank you very much.

  Hello

  Search for updated drivers and reinstall if no later by using the procedure below.

  Control Panel - network - write down of the brand and the model of the Wifi - double click top - tab of the driver - write
  version - click the driver update (cannot do something that MS is far behind the pilots of certification). Then
  Right click on the Wifi device and UNINSTALL - Reboot - it will refresh the driver stack.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  Download - SAVE - go where you put it - right click – RUN AS ADMIN.

  You can download several at once however restart after the installation of each of them.

  After watching the system manufacturer, you can check the manufacturer of the device an even newer version. (The
  manufacturer of system become your backup policies).

  I would also turn off auto update for the drivers. If the updates Windows suggests a just HIDE as they
  are almost always old, and you can search drivers manually as needed.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• FATAL alert: BAD_CERTIFICATE - a damaged or unusable certificate has been receiving

  I try to call a third part-service web (EDC RAVE) through the Oracle Service Bus/Weblogic Server. However whenever I try to use a business service to connect, I get the following error message:
  
  The invocation was an error: FATAL Alert: BAD_CERTIFICATE - damaged or unusable certificate has been received...
  
  I tried to add the certificate to the CTL of demo all, but appears not to have solved the problem. Anyone know how to solve the problem?
  The only solution I've found is:
  http://download.Oracle.com/docs/CD/E13222_01/WLS/docs81/webserv/trouble.html#1071057
  
  But I am using 10.3, not 8.1.

  CN = *. mdsol.com

  WL don't like wildcard certificates.

  If you submit your request to "someserver.mdsol.com" and you get back the above, you will get the error.

  You can
  Disable the check name host (never a pleasant thought)
  Write from your own host name check custom
  * Ask a certificate specific to their host ("with a CN of" someserver.mdsol.com, for example).

  Perhaps a useful link:
  http://jandrewthompson.blogspot.com/2010/04/WebLogic-and-wildcard-SSL-certificates.html

  Published by: user10939158 on April 26, 2010 15:51

• Access point lose connection to WLC 7.6.130

  Hi all

  When we try to move the access points of 7.0.116 7.6.130 controller (5500). Access point is continuously lose the connection with wlc and the record of the return.

  Can someone please help! Here are the logs. Please let me know if you need more information.

  * 10:05:23.547 Nov 20: % LWAPP-3-CLIENTERRORLOG: connected mode
  (.,) 3 20 10:06:11.279: % 3-CAPWAP-ERRORLOG: County of Retransmission for package exceeded max (CAPWAP_WTP_EVENT_REQUEST
  * 10:06:11.283 Nov 20: LWAPP-3-CLIENTERRORLOG %: switch to standalone mode
  * 20 Nov 10:06:11.287: % 3-CAPWAP-ERRORLOG: dating BACK to the DISCOVERY of FASHION
  * 10:06:11.287 Nov 20: % DTLS-5-SEND_ALERT: send FATAL: close notify alert at 10.50.65.61:5246
  * 10:06:21.343 Nov 20: % 3-CAPWAP-ERRORLOG: MWAR selected ' ERFWS019.u70015'(index 0).
  * 10:06:21.343 Nov 20: % 3-CAPWAP-ERRORLOG: go join a capwap controller
  * 10:06:22.000 Nov 20: % CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.50.65.61 peer_port: 5246
  * 10:06:22.615 Nov 20: % CAPWAP-5-DTLSREQSUCC: DTLS connection created successfully peer_ip: 10.50.65.61 peer_port: 5246
  * 10:06:22.615 Nov 20: % CAPWAP-5-SENDJOIN: send request to join 10.50.65.61
  * 10:06:22.671 Nov 20: % 3-CAPWAP-ERRORLOG: white event 10 & combination State 5.
  * 10:06:22.671 Nov 20: % 3-CAPWAP-ERRORLOG: CAPWAP SM Manager: unable to process the message status type 10 5.
  * 10:06:22.671 Nov 20: % 3-CAPWAP-ERRORLOG: could not manage capwap control message from the controller
  * 10:06:22.671 Nov 20: % CAPWAP-3-Journal of ERROR: failed to process the encrypted package 10.50.65.61 capwap
  * 10:06:22.763 Nov 20: "Promiscuous" from Ethernet mode
  * 10:06:23.163 Nov 20: % LWAPP-4-CLIENTEVENTLOG: OfficeExtend Localssid recorded Flash AP
  * 10:06:23.387 Nov 20: % CAPWAP-5-JOINEDCONTROLLER: AP joined controller ERFWS019.u70015
  * 10:06:24.439 Nov 20: LWAPP-4-CLIENTEVENTLOG %: No. Flex ACL to load map configuration file. To connect to the controller to get the configuration file
  * 10:06:24.439 Nov 20: LWAPP-4-CLIENTEVENTLOG %: No. Flex ACL to load map configuration file. To connect to the controller to get the configuration file
  * 10:06:24.439 Nov 20: % LWAPP-4-CLIENTEVENTLOG: map No. LS Flex to load ACL configuration file. To connect to the controller to get the configuration file
  * 10:06:24.439 Nov 20: LWAPP-4-CLIENTEVENTLOG %: no central Dhcp configuration file map to load. To connect to the controller to get the configuration file
  * 20 Nov 10:06:24.439: % 3-CAPWAP-ERRORLOG:
  Flash file: / configs/AP_LAYER2_ACL_MAPPING_PAYLOAD_file not found
  * 10:06:24.439 Nov 20: % 3-CAPWAP-ERRORLOG: flash Configuration file: / configs/AP_LAYER2_ACL_MAPPING_PAYLOAD_file read failed

  * 10:06:24.439 Nov 20: % LWAPP-3-CLIENTERRORLOG: connected mode
  (.,) 3 20 10:07:11.167: % 3-CAPWAP-ERRORLOG: County of Retransmission for package exceeded max (CAPWAP_WTP_EVENT_REQUEST
  * 10:07:11.171 Nov 20: LWAPP-3-CLIENTERRORLOG %: switch to standalone mode

  .

  Have you checked the details of mapping vlan are there in the AP?

  Try to put in local mode & set it up the new FlexConnect mode & see

  HTH

  Rasika

  Pls note all useful responses *.

• Tecra 9100 - unable to connect to the WLan access point

  Hello

  I have a Tecra T9100 with miniPCI WLan. I reinstalled XP Pro and all the drivers (downloaded from the Toshiba site) and I've always had a problem with Wifi:

  I can see all access point (in the windows control panel), but when I click on connect, I received a message that the access point is no more...
  He didn't ask me for the security settings?

  does anyone have an idea?

  Much thanks

  Leclere

  Hello

  To my knowledge the Tecra 9100 was equipped with the wireless LAN standard: 802. 11B mini card PCI ORiNOCO.

  You need to check if the WiFi signal is strong enough for a transmission correctly
  I think that the signal of WLan access points is not strong enough because of the distance.

• can I use a laptop to set up a wifi access point?

  When I first received a laptop of opportunity in last December, a colleague tech at my night school mentioned that I didn't have to buy a 803,11 access point device to plug my switch, but I rather use a WiFi card on my computer to create my own access point. I told him I have such a card and put a little out of my mind.

  However, I have someone outside to spend the night at my place, and he needs to check his e-mail. Unfortunately, it seems that the RJ-45 socket on his laptop is broken, I have tried several cables and impossible to get a connection, including the cable to connect the computer I'm using now.

  Is it possible that I can use ICS on XP Pro (preferred) or Vista 32 bit Home Premium (really want to use it, I have never set the boot loader after the upgrade to XP on a separate partition, especially because XP has worked so much better) to set up enough connectivity for him to connect to the mail server?

  Should I Windows 7 or Vista to do this? I know how to do the reverse quite easily (share Wi-Fi on the Ethernet port), but I don't know how to set up the SSID and others. I would assume same WEP or WPA2 (Yes, I know how it is easy to crack, but it's better that transmitting passwords in clear text because it discourages occasional interception) would too, so it will accept a connection open, unencrypted. I'll just close access once it does.

  How could I go to set it up? I'm not spending money on software that is not free for one night, one-shot deal. Kiss, I just need a connection of bare bones for him. If its Ethernet port was working, I would leave him to plug my switch, but since it's not I need to create a gateway using what material I have on hand, and the only device with any kind of ability 803.11 is my own laptop.

  I know it's possible, I don't know if this is something only Linux, or a solution that requires 3rd party software.

  Yes, you can use ICS.  See http://practicallynetworked.com/sharing/xp_ics/

  I forgot to include this--> http://www.home-network-help.com/ad-hoc-wireless-network.html

  You will need to configure security manually from the properties of maps dialog box wireless (on both computers) and IIRC, you can use WEP in ad-hoc XP networks.

  Go to the correct place
  Right click on the wireless adapter icon and select Properties
  Click the wireless networks tab
  Click Add to create a configuration
  in the 'Association' tab, set the SSID, network authentication 'Open' and WEP data encryption.
  It's been so long that I made that I remember exactly, but I think you can use only the 10 digit Hex key.

• RE6500HG has not detected 5 GHz dual-band access point transmission

  I have a dual band (2.4 GHz & 5 GHz) access point in the living room and the RE6500HG is located in the room adjacent to the living room. During the installation of the RE6500HG could detect only the 2.4 GHz transmission and after a few tries I had to settle for a configuration unique (2.4 GHz) band.

  My iPad Air in the room, could receive the signal of 5 GHz from the living room AP. In an experiment, I put in place the RE6500HG in the living room at distances ranging from 1 meter to 5 meters without success in the configuration of the 5 GHz RE6500HG

  My RE6500GH is defective? I bought the unit yesterday (April 27)

  Try adjusting the road s 5 GHz to channel 36.

• Access point

  Hello!

  Today, I received the WAP610N, but I have some problems...

  I have my router to the ground level and a Repeater to the first floor, both work very well. Now I tried to connect my PC (PCI WIFI n card) which is located on the second floor of this network, and I thought that it would work with the Access Point.

  Is there a way to do it, or am I better with giving it back and get a PCI card? I really prefer to use the WAP610N, because I could just plug in, and I don't have to use a PCI of the WLAN card slot.

  The WAP610N is an access point. It is not a Repeater or a wireless bridge.

  Get a wireless adapter or a wireless bridge.

• IP E1200 as access point ranges

  I have a Cisco 880 (provided by my company and as such, I have little access to the control panel). I have a Linksys E1200 (Cisco) to use as an access point. Installation of Cisco (love it!), but the simple configuration gives the E1200 a range of ip addresses from 192.168.1.1 while Cisco 880 range is 192.168.185.113. I need to have connections in the same rage of ip (192.168.185.xxx) for remote monitoring. What is the best way to achieve this? Bridge mode (I have no need to Mode of reviews I've read is not possible in bridged mode)? Disable DHCP on the E1200? I've been roaming forums, but there's still a few confuson. Guidance gratefully received.

  Hello

  You have two configuration options for the desired configuration. You can make the LAN to LAN (cascading) configuration or in Bridge Mode. Well the 2 types of installation are the same. The only difference is that you must manually configure all on LAN to LAN setup.  It includes turning off DHCP and manually configure an IP address for the E1200 (which will be the secondary router). Configure the router bridge Mode automatically disables router functions and sets the router as a simple switch/access point.

  For me, I will configure using the method of the Bridge Mode. It's going to be much easier that way. Please click on the following links learn more about the waterfall and Bridge Mode:

  In waterfall or connect a Linksys router to another router

  Set up your Linksys WiFi or Smart WiFi router in Bridge mode

• Access Point WRT1900AC & Firmware version: 1.1.10.167514, it cannot be accessed the config page.

  Hello!

  I am a new user of router dual-band WRT1900AC . The installation has been updated instantly to
  Firmware version: 1.1.10.167514
  Release date: June 30, 2015

  My WRT1900AC is configured as a wireless gateway.

  https://community.Linksys.com/T5/wireless-routers/WRT1900AC-as-wireless-access-point/TD-p/847286

  Also, I have disabled firewall and uPnP.
  A tutorial here:

  http://www.Linksys.com/us/support-article?articleNum=140371

  Everything works except that without access to the router config page.

  The problem is, I can't access my page to config WRT1900AC Wireless Access Point and the only solution is to connect temporary exit HAND ROUTER LAN to WAN WRT1900AC, can I access my AP

  (after restart of course). Change after I return the cable to the LAN again and restart WRT1900AC. This works.

  Yesterday, I spoke with live chat. I received recommendations:
  "Once the router is configured to bridge fashion, page configuration accessible only using its new IP address. The new IP address can be found on the main router DHCP table. It is because only in LAN - LAN, the

  WRT1900AC will be his disabled DHCP. »

  I also saw Table of customer routers main DHCP but I have not found the IP address of my wireless WRT1900AC Access Point there. I think it is a bug in the version of the Firmware: 1.1.10.167514
  Page config in the case of WRT1900AC Wireless Access Point is isolated or possible only thanks to the WAN WRT1900AC. It would be nice if someone confirms that and maybe in the next version of

  fix. :-) I have a beautiful smartphone App "Smart Wi - Fi" and I can not comfortably use it due to this error/bug.
  Otherwise everything works well and stably.

  inspire wrote:

  Hi chadster766!

  Thanks for your suggestion and a quick response. I have a feeling it would work then as you described. But how to set Internet settings in mode Bridge? I've already put a static IP address router IP address WRT1900AC. I see it with IP scanner.
  If I leave the cables as you suggest (hand router LAN to WAN WRT1900AC), the Internet does not work. In this case go to the config page, but Internet with other devices will not work. Also good Wifi, it works but can not access. How to set the Bridge Mode? (I think this is my problem in this scenario)

  IP address of the router (LAN):

  Connectivity-online-online details router LAN => Edit

  * If your main router IP subnet example is 192.168.0.x, then set the address of the WRT1900AC IP to an IP outside the range of the main router DHCP. Ex: 192.168.0.2

  Bridge mode:
  Connectivity-online Internet-online IPv4 settings => Edit-online Bridge Mode

• Wireless-G Access Point WAP54G & Thompson SpeedTouch ST585

  For the life of me, I can't get this device to work. I am trying to create a point of access to a device not pc a FTA Receiver. The FTA Receiver needs access to the internet and works very well with an ethernet cable. I had hoped to use the WAP54G as a wireless connection. The installation CD does not recognize the modem/router Thompson SpeedTouch ST585 so I've been using the web to access the settings of the WAP54G. I did some readings using Google search and access via the web, I had to leave it white instead of enter "admin" after that tumble down the Userid first discovered, always through Google, I have tried setting the SSID, the same name as the SpeedTouch ST585 "INFINITUMB69844" done more reading I found that I needed to set the security on the WAP54G are the same on the SpeedTouch ST585 in my case as WEP passphrase window and set the WEP encryption key and press the button generate, which filled up all the empty spaces of keys. I am on windows XP and the fact a network routine from the control panel and also the repair option. Still no go. Unity of FTA, I am trying to connect has a DHCP option auto who will fill the IP address once it connects to the network so far all I get is zero, it does not connect. I need help with the settings. I did put my PC IP static or tried other methods suggested on Google. I thought to ask the experts. Please help me. Chris

  How you try to configure your Access Point and where are you going to connect this AP?

  As you mentioned that you have a Thompson Speedtouch router, and that you have entered the same settings wireless to your router to the AP, and if you plan to connect the AP to another device, then it is not not possible.

  WAG54G will work only in Repeater Mode / Mode Bridge that with the Linksys router, with all other routers it only works in a Mode Access Point, it means you need to keep this access point wired to your Thompson Speedtouch modem always.

• to convert 1142N AP autonomous lightweight access point

  Hello

  I have 4 1142N access points are all points of light access. Because I don't have a controller, I need to convert to standalone AP.

  I went through document cisco 1142, where it is mentioned that "the access point 1142 doesn't have the default IP address"

  I know procedure to convert offline in which I need to connect ap to the TFTP 10.0.0.1 with the ip address by default, but as for 1142, we do not have the default ip address. What is the procedure to convert offline?

  I have to assign a pool in one of the local switch and connect the ap to these switches with vlan, so she will receive the IP address of the DHCP server?

  But how can we without default IP address? I wonder about this...

  If I did not turn on where I can assign pool dhcp... what should I do?

  Please suggest me to convert 1142 standalone AP ap...

  I will be thankful to get the right answer...

  Hi Vinod,

  Here's the resolution...

  The image that is on the device's LWAPP, not the autonomous... If you want to use the AP in stand-alone mode, then the image must be W7...  It's...

  C1140-k9w7 - tar.124 - 21A .JY .tar not c1140-rcvk9w8 - tar.124 - 23c.JA.tar

  Please feel free to download any image from the below link and perform the conversion of image LWAPP to stand alone...

  http://tools.cisco.com/support/downloads/go/PlatformList.x?sftType=IOS+Software&mdfid=282439881&treeName=Wireless&mdfLevel=Model&url=null&modelName=Cisco+Aironet+1140+Access+Point&isPlatform=N&treeMdfId=278875243&modifmdfid=null&imname=&hybrid=Y&imst=N

  the methos to convert is...

  Download TFTPd32 of google and install it on your PC... point of the image that you downloaded on the TFTP server.

  Connect a cable ethernet between your notebook and AP... both should be on the same subnet... Connect a cable from the console and access the hyperterminal console with the command... Make sure that you are able to ping the PC and AP and vice versa!

  AP > en

  AP #debug lwapp console cli or debugging console cli capwap

  T AP #config

  AP (confg) int FA 0

  AP(confg-IF) ip addr (same subnet as the laptop)

  End AP(confg-IF)

  Force - reload DOWNLOAD - AP #archieve sw / overwrite tftp: / /.

  Force - reload DOWNLOAD - AP #archieve sw / overwrite tftp: / /<10.0.0.5>/c1140-k9w7-tar.124-21a.JY.tar

  The above command will do it for you!

  Let me know if that answers your question...

  Concerning

  Surendra

  ========

  Please don't forget to rate the post if this has been useful for you or useful

• Power level of the access point

  I am running 7.0.164 WCS and series access point 1130 firmware 7.0.98.0.

  I get a lot of complains about the students that their laptops do not get 5 bars signals.   They receive at least 1 or 2 bars with being disconnect the frequency.

  Problem is that the 2 closest access points are power TX 2 level.   For the purpose of the test, I increase the level of tx power to 8 on access points and signals 5 portable bars, see the.

  The dorm is 3 (2 rooms / 2 persons per room more bedroom bathroom and living room) suites by the wings. The walls are concrete.

  I was told that using the custom for the TX power level setting is not recommended.

  What are the solution to this problem?    Use the custom setting or what?

  Allen,

  Your description of the problem that is absurd, especially considering that a power of 8 level is lower than the power level 2.

  If you do a ' show config ap 802. 11A '

  It will show you this

  TX power
  Number of supported power levels... 5
  TX 1 power level... 11 dBm
  Power TX 2 level... 8 dBm
  Power TX 3 level... 5 dBm
  TX 4 power level... 2 dBm
  TX Power Level 5 dBm...-1
  TX power setting... Automatic
  Current Tx power level... 5

  If you do a ' show config ap 802. 11 b '

  It will show you this

  TX power
  Number of supported power levels... 8
  TX 1 power level... 20 dBm
  Power TX 2 level... 17 dBm
  Power TX 3 level... 14 dBm
  TX 4 power level... 11 dBm
  Power TX 5 level... 8 dBm
  TX 6 power level... 5 dBm
  TX 7 power level... 2 dBm
  TX Power Level 8...-1 dBm
  TX power setting... Automatic
  Current Tx power level... 8

  So based on the fact that you said that Power Level 8 gives you a stronger signal is suspicious to say the least.

  I hope this helps... Please evaluate the useful messages.

  Thank you

  Kayle