Wireless-G Access Point WAP54G & Thompson SpeedTouch ST585

Similar Questions

• Linksys Wireless-G Access Point WAP54G ver 3.1 security problem

  Hello!

  I have WAP54G access point in our network. I would like to change the WPA security settings, but am not able to do.

  I did everything as mentioned in the installation manual, and I get to the 5th sheet of status points: Firmware version v.304, MAC (numbers), the 192.168.1.245 IP address, SSID linksys channel Channel 6 and disable WEB security

  What I would do, is to change the SSID and WPA2 security. When I'm clicking 'Yes', he goes to the next sheet "Password", I write admin and click on "Enter". "I'm going to pop-up window Setup access violation" at address 0049BDB6 in module 'Setup.exe '. Write to the address C933016A. »

  So please, any ideas what to do? This shouldn't be so hard... It works very well as an access point, but I need to have at least some security.

  BR,

  VESA

  P.S. both are physically the same hub

  I suggest resetting the access point and configure manually. Access just the link below for your reference.

  http://www6.nohold.NET/Cisco2/UKP.aspx?VW=1&docid=6579d209b91949adb3f355fceaa2296f_16627.XML&PID=80&...

• Unable to connect wireless integrated Touchsmart IQ506 to Netgear's WNHDE111 Wireless - N Access Point

  I have a new HP Touchsmart IQ506 and the experience has been very positive with one exception: the Wireless-N networks.

  I bought a Netgear Wireless-N reduction kit.  I am able to see (in the Vista network and sharing Center and available networks), using the Netgear Wireless-N USB adapter Netgear WNHDE111 Wireless-N access point provided with the Touchsmart IQ506 and connect to it without problem.  But I am unable to connect directly to WNHDE111 with Wireless-N adapter integrated the IQ506 (on the HP Touchsmart IQ506 or on another PC with the Wireless-N support, a Sony Vaio NS150 computer).

  Ralink 802.11n adapter indicates that "working properly" in the Device Manager.

  Am I missing something?  Are there instructions on how to connect the IQ506 up to an access point Wireless N with the built-in wireless adapter?

  
  

• Access point WAP54G whose MAC addresses are the same

  I have 3-point WAP54G access that are connected together using wireless bridge settings found under the "AP Mode" in the menu.

  I would add a fourth unit, but as I am doing so I discovered that the 4th unit network MAC address is the same as that of the three already existing in my lan bridge WAP54Gs.   How can this be?  All units, aren't supposed to have unique MAC address of the factory.  I have triple checked to make sure that I am indeed two different units WAP54G.  Yes there is indeed to disting WAP54G units in my possession to what appears to be duplicate MAC addresses.  Then two units with double MAC addresees exsist on the same bridge LAN?  If this is not the case, is it possible to change one of the units, itg is not possible to return a device?  Thanks in advance for your help in this matter.

  David Desesquelle

  Tech Mgr.  HE

  Capricorn productions

  New Orleans, Louisiana

  (Mod Note: deleted non-public information.) (Thank you.)

  What is the common MAC address?

  Concerning

  Fred

• WAP54G Access Point in Client Mode

  A client mode Linksys Wireless-G Access Point can communicate with a wireless-n wrt300n router?

  I continue to see the next note that worries me, it won't work:
  NOTE: The WAP54G will communicate only with an another WAP54G when the value for the Client Access Point.

  If this is not the case, what can I use to connect my PC to the floor to my router to wide band wireless downstairs. I prefer to use something other than a wireless NETWORK card because the PC is in a bad spot in the House.

  Thank you.

  Thank you.

• Error message 'Please select the access point or wireless router to set up' when you set up a network

  Original title: set up a network.

  I want to create a wireless network for the games, and when I click on the network. A screen comes written on this "Choose the access point or wireless router to set up" and that "it might take 90 s for devices reconfigured to appear on your computer.

  But no device never appears below it, even after 90 minutes.
  Please help me with this.
  It was so easy in windows 7.

  Hi Manas,

  What is the brand and model of the Wireless Router/Access Point?

  Given that the issue has not persisted in Windows 7, there is a chance that the wireless router/Access Point is not compatible with Windows 8.

  Please check the links below on the implementation of a network.

  http://Windows.Microsoft.com/en-in/Windows-8/Setup-home-network

  http://Windows.Microsoft.com/en-in/Windows-8/what-you-need-Setup-home-network

  http://Windows.Microsoft.com/en-in/Windows/set-up-wireless-router#set-up-wireless-router=Windows-8

  http://Windows.Microsoft.com/en-in/Windows-8/Add-device-or-PC-to-network

  Answer please if you have any questions.

• Can I use my Satellite P10 as Access Point?

  Satellite P10 wireless access point

  Please can someone help?
  I have a laptop wireless by Satellite P10, can anyone tell me is it possible to set up the laptop to share my Internet remotely even if its WiFi, so it can be picked up by my Sony PSP. Then my cell phone would act as a wireless internet access point.
  As I do not have a router, don t know if it is possible this way any ideas?
  Thank you Michael.

  Hi Michael

  Well, I m not sure if it of possible the Sony PSP to connect to the laptop and if it works, but I found several useful information how to create make it the network connection wireless home in Windows XP without a router. Please check this links.

  http://www.Microsoft.com/windowsxp/using/networking/expert/bowman_02april08.mspx

  http://www.annoyances.org/exec/show/ics_xp.

  Good luck

  Good bye

• E3000 as or to get a better access point?

  Hello, I installed an EA8500 router as my main 'brain' The entire House is wired ethernet. I have a House of very good size, so upstairs in my room... the signal of the iphone is not the best... I had a previous firmware Linksys E3000 current tomato from my router laying around... so I have set up to work as a WIRED Access Point and it works fine.

  Now my question is... I would purchase say... An AC Wireless extender/access point? Is there a different big an E3000 and a real access point/range extender wireless?

  Thank you all

  Hi manofice. If you have a lot of wireless devices that are capable AC and having a challenge with the connection to the EA8500, then Yes, it may be preferable to get an AC range extender. But if only the iPhone was having a problem with wireless connectivity and you mentioned adding the E3000 as access point is working fine, then it is not necessary to get an Extender for the moment.

  Hope that helps.

  Liezl-10104

  LInksys technical support

• Access Point WRT1900AC & Firmware version: 1.1.10.167514, it cannot be accessed the config page.

  Hello!

  I am a new user of router dual-band WRT1900AC . The installation has been updated instantly to
  Firmware version: 1.1.10.167514
  Release date: June 30, 2015

  My WRT1900AC is configured as a wireless gateway.

  https://community.Linksys.com/T5/wireless-routers/WRT1900AC-as-wireless-access-point/TD-p/847286

  Also, I have disabled firewall and uPnP.
  A tutorial here:

  http://www.Linksys.com/us/support-article?articleNum=140371

  Everything works except that without access to the router config page.

  The problem is, I can't access my page to config WRT1900AC Wireless Access Point and the only solution is to connect temporary exit HAND ROUTER LAN to WAN WRT1900AC, can I access my AP

  (after restart of course). Change after I return the cable to the LAN again and restart WRT1900AC. This works.

  Yesterday, I spoke with live chat. I received recommendations:
  "Once the router is configured to bridge fashion, page configuration accessible only using its new IP address. The new IP address can be found on the main router DHCP table. It is because only in LAN - LAN, the

  WRT1900AC will be his disabled DHCP. »

  I also saw Table of customer routers main DHCP but I have not found the IP address of my wireless WRT1900AC Access Point there. I think it is a bug in the version of the Firmware: 1.1.10.167514
  Page config in the case of WRT1900AC Wireless Access Point is isolated or possible only thanks to the WAN WRT1900AC. It would be nice if someone confirms that and maybe in the next version of

  fix. :-) I have a beautiful smartphone App "Smart Wi - Fi" and I can not comfortably use it due to this error/bug.
  Otherwise everything works well and stably.

  inspire wrote:

  Hi chadster766!

  Thanks for your suggestion and a quick response. I have a feeling it would work then as you described. But how to set Internet settings in mode Bridge? I've already put a static IP address router IP address WRT1900AC. I see it with IP scanner.
  If I leave the cables as you suggest (hand router LAN to WAN WRT1900AC), the Internet does not work. In this case go to the config page, but Internet with other devices will not work. Also good Wifi, it works but can not access. How to set the Bridge Mode? (I think this is my problem in this scenario)

  IP address of the router (LAN):

  Connectivity-online-online details router LAN => Edit

  * If your main router IP subnet example is 192.168.0.x, then set the address of the WRT1900AC IP to an IP outside the range of the main router DHCP. Ex: 192.168.0.2

  Bridge mode:
  Connectivity-online Internet-online IPv4 settings => Edit-online Bridge Mode

• WRT600N advanced routing problems / use as Access Point and switch

  Firmware 1.01.36 build 4 The WRT600N is connected to an existing LAN and is really only used as a Wireless N access point. There is nothing plugged into the WAN port; only the LAN port. I have NAT disabled. All traffic from a client connected to the WRT600N wireless going very well for the gateway and the Internet router. The customer experience is very good. However, there are a few minor issues as follows.

  1] Setup > Advanced Routing tab has only the following options; to do this, * not * have a picker 'Mode '. NAT, static routing and dynamic routing (RIP).    IS this NORMAL, OR should HAVE a MODE (e.g. switch) AS REFERRED to IN THE HELP FILES?

  [2] even if a connection wireless or wired to the WRT600N works very well, the WRT600N himself is unable to connect to the internet. It cannot connect to NTP to set the time and I can't ping past the gateway router using the ping of the WRT600N diagnostic utility. I ping the gateway 192.168.1.4 port inside, but I can't use the diagnostic the WRT600N ping ping utility something beyond this gateway port. The routing of the WRT600N table is below. THE GATEWAY SHOULD NOT BE 192/168.1.4? HOWEVER THE WRT600N DON'T ME LETS NOT CHANGE IT.

  Destination LAN IP Subnet Mask gateway interface

  192.168.1.0 255.255.255.0 192.168.1.71 LAN & Wireless

  127.0.0.0 255.0.0.0 * LAN & Wireless

  Topic 1. Linksys, used to have a mode option to switch between the modes 'Bridge' and 'router '. The latest routers call it now better NAT power. Gateway mode means THAT NAT is enabled. Router mode means THAT NAT is disabled. The help files are probably a little bit over. But the option is still the same.

  Re 2. It's normal if you use it as only access point (i.e. do not use the WAN port). The router always takes into account that the internet connection via the WAN port, i.e. it will always use the default gateway on the WAN port. If nothing is connected to the WAN port on the router itself has no default gateway and therefore has no access to the internet. Generally, you are not able to establish the default route in either advanced routing page. It is a known limit of these routers if you do not use as a router.

• WAP54G Access Point using wireless mode, but not worked. :(

  I bought today WAP54G.
  My son and I have PC but we distance between our room each other and
  wireless signal is not strong enough sometimes.
  My son has wired Internet w / WRT54GS router and I have wireless
  USB G adapter to my room.
  Cat w / Linksys rep, the other day and he recommended buying WAP54G and I could leave this AP @ salon and do not need to have the connection cable.

  Anyway, I don't know how to install this customer service, called today
  and she told me that I need to install the CD in my computer. But there is no
  connection by cable or router and I cannot install CD in my computer.
  So, I installed the CD in the PC of my son who has wired Internet and
  router. The installation has been completed.
  After the installation, turn off AP and move on to the living room.
  Then, there is no "link" light on. Lamp only Power and act on.

  Tried chat w / online but offline and it is really difficult to chat w /.
  them.

  Please let me know:
  1. can I use this without wired access point?
  I would like to implement the AP @ living room (between my son and my room)
  2. which PC do I need to install CD? But once again, my PC have no cable
  connection and cannot install the CD.

  I am very beginner wireless and PC so please tell me step by step.
  I read manual and I used the installation CD Wizard but still do not work.

  Please someone help me.

  I think that you must configure your AP as Repeater wireless... Follow the link here , make sure that when you set your Access Point to the "Wireless Repeater" mode, this device will communicate only with a different Access Point Linksys (WAP54G) and wireless G of Linksys (WRT54G) router...

• Wired access point / wireless home network

  I am a littlenew to this, sought several messages, but cannot find one that fits exactly to my question/questions.

  The installer: The floor cable modem to the router (BEFSR41).  An electrician on desktop on the floor. A wire hard out of the router (WRT54G) B downstairs for LAN wired stereo components and a Wi - Fi connection for laptops.

  Router B has DHCP set IP same as router and connection is on the LAN 1 port instead of port Internet, Xbox and other components on the LAN 2, 3, 4 ports. Laptop computer Upsairs wireless internet access and are working very well. I can't move the modem to the floor, and the wireless should point down because if it's on the floor there is too much signal loss.

  Question: Xbox 360 is connected to router B (bottom) via wired LAN, and after about 5 minutes loses the internet connection.

  Question: What is the correct configuration for the router A and router B? Is there a better Setup for this?

  I can't answer this question because I do not know the subnet on your network.

  Allows to make a few assumptions here well and you can change your IP according to your needs.

  Router

  IP=192.168.1.1/255.255.255.0

  Remember that it is the side LAN not IP address on the WAN side.

  Router B

  IP=192.168.1.2/255.255.255.0

  Default gateway = 192.168.1.1

  DNS = 192.168.1.1

  The WAN should be turned off or disabled.

  WAP54G

  (Default) IP=192.168.1.245/255.255.255.0

  Default gateway = 192.168.1.1

  Customers

  IP=192.168.1.100-150/255.255.255.0 (this isn't how you should express this value correctly, but it is easier for the non technical to understand person).

  The default gateway on all clients would be 192.168.1.1

  The DNS on all clients would be 192.168.1.1

  I assumed router B is hard wired from a LAN port on the router B on a LAN port router.

  The channels on router A & B should be different unless your roaming between devices. I don't remember if the Linksys firmware allows and or compatible WDS. I think it does, but you have little or no control over it, so therefore people tend to install third-party firmewares.

  Security on router B can be anything. But if you changed it from the beginning and you windowz cliewnts you will probably have to remove the profile stored by the client wireless and reconnect to the HA to rebuild the front profile it will not work properly. Windowz update the key in the profile stored, a pretty stupid mistake the share nanasoft.

  in any case, theres a start point for you.

  Concerning

  Fred

• WAP200 Wireless - G Rangebooster POE Access Point

  I have a few questions about the foregoing, called Access Point.

  I searched the site of Linksys and has failed to locate the manual for it.

  So I wanted to ask if someone can give me the link to the manual is?

  Also I wanted to ask you whether the above-named Access Point is Automatic Configuration of the button that

  would allow him to detect and use the optimum depending on the network parameters (provided that it is

  connected with other linksys products)?  Since it is an access point what review / limitations exist

  in case that the bridge isn't a linksys one?

  Q: well the question is if I connect to an Access Point (say WAP54G) in Access Point mode to a switch that allow a Wireless Client to connect to the network.

  A: Yes, that would allow a wireless client to connect to the network. Deal with the AP as a "wireless switch". If you have DHCP running on the network, the DHCP information will also provide computers wireless connecting to the AP.

  Q: the second question is how can I connect a gateway (for example WAG200G) so more that the entire network to the Internet?

  A: you can connect the WAG200G to the switch. Your installation will be: WAG200G - switch - AP))) (((Wireless PC

• I need assistance with my WAP54G access point!

  I tried to connect my nintendo dsi to the internet using the WEP encryption, so I went to my router configuration page, then he wasn't no matter what tab wireless or settings on the page... my dsi SYSTEM can go to the internet via the setting of WPA, but my games, which is supported with WEP setting cant. so, I really need someone's help now! I don't want to miss the online features of my games... also, I asked my father if he can help me then he says he can only if I find the CD or download WAP54G ver 3.1 somewhere.

  Thanks in advance...

  If your Access Point is connected to a wired router, so you don't have to change the settings of your router, you just need to enable wireless security and change the SSID of your Access Point, and it should be good to go... Also make sure that your Access Point is in the subnet of your router...

  If the IP address of the router is 192.168.1.1, then the Access Point on your address IP should be 192.168.1.245...

• Use WAN connected airport Time Capsule as a wireless access point

  I had to replace a failed 4 Gen Time Capsule. I tried to install a new Gen 5 airport TimeCapsule via WAN and set up the airport to act as a wireless access point. It is installed in an area of my house with wireless coverage. In the network of AirPort Utility Mode section, I chose "extend a wireless network. The TC is restarted, I get an error message cannot find the intended wireless network.

  What I lack?

  "Extend a wireless network" is a parameter that is only used if the time Capsule need to connect to another router from Apple with the help of a Wi-Fi connection.

  You use Ethernet to connect, you must use the parameter to "create a wireless network. Use the same wireless network name and the same password as your "primary" router