OfficeJet R65 Scanner driver

Similar Questions

• Scanner HP Officejet R65 for Windows 7 driver

  I have a HP Officejet R65 all in one connected to my laptop via a USB cable to printer. I recently updated my laptop to a Lenovo G550 with Windows 7. I got the R65 works well as a printer in Windows 7 by selecting 'windows update' when performing "add new printer", as advised on this forum. But I was not able to find a driver for the scanner function work. Please can you advise me how to do this?

  Kind regards

  Edward

  I think I know now what the problem is. It seems that the Logilink USB to parallel converter cable, D - SUB 25-pin ((UA0054) supports only the basic functions of parallel printer and not to other functions such as the scanner.) The only way to get the scanner to work will be to find a more sophisticated connection.

  Thanks for all the help and advice.

• OfficeJet R65 driver for Windows 7

  I just upgraded to a PC running Windows 7, but it doesn't have a printer driver for my HP Officejet R65 all-in-one;  and the HP site does not list one. Any suggestions please? I wouldn't give up my, although new, printer just because there is no updated driver!

  R65 pilots should be available via Windows Update.  Go to the devices file and printers, add a printer, select the appropriate port, and then click Windows Update, then select the HP Officejet R65 once again fills the list:

  

• HP OfficeJet 6500 Wireless - bug Scanner driver - only on Windows 7 platform!

  Date:
  October 29, 2010, Roende, Denmark.

  TO:
  Hewlett-Packard
  Support / Department printer driver.

  From:
  Jesper Simonsen
  Denmark.

  Hello Hewlett-Packard

  I have an error message you bringing on the
  HP OfficeJet 6500 Wireless
  Driver for Windows 7 printer platform.

  This bug only exists on the Windows 7 platform
  and not on Windows XP.

  I was hired to install the
  HP OfficeJet 6500 Wireless yesterday.
  I have installation, installed, set up the printer.
  I configured the printer to run
  Wireless network with gateway router
  SSID and WPA key and it went smoothly.
  I installed the printer for
  address fixed LAN IP 192.168.1.197
  and I configured the gateway routers
  DHCP pool to go until 192.168.1.195
  for not to disclose the IP address of the printer.

  On a new laptop Lenovo running Windows XP
  running on the same wireless network that I installed
  software of the printer from Windows XP/Vista driver disk provided.
  It worked fine with functions of printer and scanner.
  I could also press the Scan button the
  the printer front panel and choose the laptop
  and then the printer starts and automatically starts the scanner
  software upward on the laptop. Thus, it works beautifully.

  So I should install the printer on your desktop.
  A new Lenovo desktop computer running Windows 7 32 bit.
  This desktop computer also works on the same wireless network.
  I installed the driver from the disk Windows 7driver to the address provided.
  Installation may well see the printer on the wireless network.
  I might send a print job to the printer.
  But it does not scan.

  I have tried both:

  -To start a computer scan job.

  The scanner respond briefly to run the scanner carriage
  down on where it should begin to start to
  to scan, then it stopped all communication.
  He sits for a while and then finally there will be an error message
  No communication to the scanner, which had the error code:

  4, [(2,7,80040007), (3,7,0)]

  -J' also tried to press the "Scan" button
  on the front panel on the printer and then go through
  options that are displayed on the screen on the front printers.

  It said on the screen before she had no scan options.
  On the computer, it showed a message
  We should update the list of LCD on the screen of the printer.

  I did it with the help of the HP solution center text.
  I found where I could update the scan job type options.
  I could add/remove them. Then, I sent to the printer.
  Analytical work was then on the display of fine printers.
  The same error: Scanner carriage moves down to the other end
  the scanner then stops all communications from there.

  I tried to google the number of problem and error.
  I found several other users with the same problem we had.
  I could see a webpage that people could download
  the latest printer driver, then it should resolve itself.

  The provided disks were
  -Disk with drivers for Windows XP and Vista
  -Disk with drivers for Windows 7 (32 and 64 bit)

  The drive for Windows 7 has been driver version 13.0.0
  and I could download the driver 140.0 version (English)
  (I guess that's v.14.0)

  So I downloaded this driver package.
  (I downloaded it 28 October 2010)

  First of all, I uninstalled all THE HP drivers and software on Windows 7
  and then did a reboot of Windows 7.

  Then I started to install the new version 14 of the pilot.
  The installation went without problems.
  But this driver has the same BUG than the previous driver.

  I went to the new driver HP Web site
  and downloaded all the updates that were available and
  installed to them all and still no luck with the problem of scanning.

  I had Windows Firewall turned off completely all the time.
  It is therefore not the firewall blocking anything.
  The connection to the printer is good because print jobs worked well all the time.

  Then I would try to connect the printer with USB cable
  the computer fixed Lenovo, to see if there was a difference.
  I have re-set up the printer so that I got the printer available
  by USB connection.
  It prints very well and can scan fine if
  I put the computer starting a scan job.

  But if I pressed the "Scan" button on the front panel
  then came the SAME error as before.
  When in the list of type of scan on the front panel of the printer
  has been chosen and then began the cariage scanners
  towards the other end of the scanner.
  Then he started by the scanner to the computer software
  Then, when we pressed either the scanning/Scan now on the front panel
  on the printer OR we pressed the scan button to start the scanner software
  on the computer. Then the scanner stopped after awhile and communication
  then the error message appears again.

  The wireless network is running a
  D - Link router with wireless access point.
  SSID: alsikkevej10 (not hidden, no special characters)
  Encryption: WPA - PSK (WPA1-PSK/TKIP)
  Shared key: xxxxxxxx (with no special characters)

  CONCLUSION:
  This means that the error (bug) persists in HP
  Driver software the feature scanner for Windows 7 platform.

  When I tested it, I had the Windows Firewall turns off completely.
  It's had that nothing blocked in this way.
  Wireless worked well because we could always print.

  The Lenovo laptop could always
  printing AND scanning over the wireless connection

  Both analyze the types of employment has worked on the laptop:
  -A started from the "Scan" button on the front panel of the printer.
  -Started from the scanner on laptop computer software.

  So scan works fine on Windows XP but NOT on Windows 7 platform.

  I would like to hear from you when you have solved the problem,
  so that we can it works as it should do.

  HP, please respond to an e-mail.

  Sincerely,
  Graphics & new media designer

  Jesper Simonsen

  [text removed for privacy]

  I talked to technical support. I mentioned a level 2 technician. He told me that most of these problems is caused by a bad operating system and reinstalling it would do. I got back up, restore the operating system, restore the data and reinstall all my programs, but he was right about the problem to solve. Seems a lot of work to get the scanner to work, but my computer is slow and refreshing it anyway. Moreover, the level 2 technician also said that they would recommend to reinstall the OS every 6 months. Not so sure I want to spend hours 4 or more on this process, but my computer works certainly better!

  jandrgold

• Epson Event Manager cannot find the scanner driver. Epson said that the event handler is a windows thing, and so is the problem.

  I installed an Epson Stylus SX215. I can print, scan and copy if I use another way, but if I want to use the event handler it says that it cannot find the scanner driver may not use the event handler at all (cannot yet open the program).
  In addition, the scan option "attached to electronic mail" does nothing either. Don't know if this is because the event handler program or because he can not see e-mail programs I have.

  Hi bdelrio,

  Thanks for posting. Try running a System File Checker to find errors.

  Click Start.
  In the search box type cmd
  In the menu start right click on cmd.exe and select Run - As-Administrator.
  In the command prompt, type "sfc/scannow".
  Allow this to fill and run. Please let us know if this corrects and error, or if it reports errors, it cannot fix.

  Thank you! Shawn - Support Engineer - MCP, MCDST
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• OfficeJet Pro base driver will install

  I downloaded the HP OfficeJet Pro base Driver for Windows Server 2008 x 64 (v28.8, file named OJ8600_Basicx64_1315) for our 8600.  When I try to install on our 2008 Server, I get a message saying the driver is only for systems Win XP (32 bit), Vista or 7.

  Hello

  You can install the drivers on a server through the command line operating system using an MSIEXEC command and not by installation of graphicl such as used on a client OS.

  You can find the steps for stable printer on your server in the following document:

  http://support.HP.com/us-en/document/c03351547

  Shlomi

• Visioneer OneTouch 8700 USB Scanner Driver for Windows XP SP1 installed SP 2 compatibility mode - does not

  My machine is upgraded from XP SP2 to Windows 7. Support was interrupted by the manufacturer scanner after the pilot XP SP1.   Update of Windows in my system is always sur-installe updates automatically.   The scanner driver has been downloaded from the MFRS. ' site and installed in my computer Windows 7 in "compatibility mode for XP SP2. The scanner icon in my system tray.   To make a physical connection to my system, I get error that it can not be connected or cannot be configured.   I have two USB ports of work attached to the Mo (Chinese-"Weibu") and two USB PCI card is compatible with XP and earlier versions (as shown on the box, no mention of Windows 7).   I tried all these ports, always the scanner does not connect to my system.   In addition, my device manager under USB controllers, shows the exclamation marks in yellow triangles against two elements of the same name: "VIA Rev 5 or later USB Universal Host Controller.   I uninstalled these 2 elements and restarted my system several times, without success.   At each reboot, the yellow marks disappear but soon reappear.  But the scanner worked perfectly fine in my old XP SP 2 system before moving on to Windows 7 and before installing the USB PCI card.

  Is there a solution to this problem up the old USB devices and running in the Windows 7 environment?   (I have a very old IBM PC Camera too that works well in my old XP system, but not yet tried in the current system, even if the driver has been installed).

  If finally I am not able to use the scanner under Windows 7, I reluctantly get Windows XP reinstalled on another drive and boot into it just to be able to use the scanner which is functioning perfectly.

  I am a person of 78 years and enjoy using and experimenting with my PC, which has become an addiction for me.

  Thank you.

  You can buy a copy of XP that would probably cost more to replace the scanner and now is not the right time to install XP anyway.

  Your webcam is a lost cause. Compatibility mode has been designed to work for older programs, and Microsoft does not recommend to use it to install the device drivers. I have no idea why some here suggest a possibility...

• Adobe Acrobat 9 Pro is compatible with Windows 10? Adobe recognizes no longer scanning for my printer/scanner driver? Almost impossible to find answers and help!

  Adobe Acrobat 9 Pro is compatible with Windows 10? Adobe recognizes no longer scanning for my printer/scanner driver? Almost impossible to find answers and help!

  Hi leighh50950915,

  DC XI & Acrobat Acrobat has been tested successfully on Windows 10.

  Other versions may or may not work, difficult to predict behavior.

  However, try to uninstall & reinstall the printer drivers.

  Also make sure that Acrobat 9 is updated.

  Kind regards

  Nicos

• Scanner driver problems/communication HP Officejet 6310

  Background: buy new pc in 2006 (XP Pro)... Bought Officejet 6310 shortly after.  Installation of the software for printing (on the cd) was perfect and as directed.  Computer HP P7 portable bought in 2011, software downloaded from the HP website, installation was still perfect and according to the guidelines.

  This week, I upgraded the old pc from 2006 with new boards (re-used only the cases and the power supply).  Running Win 7 Pro 64-bit.  AIO_CDB_Net_Full_Win_WW_130_141 downloaded from HP, has begun to install.  Problem started when, during the installation process, I turned on the Officejet 6310 and plugged the USB cable as shown. The below screen appeared... not all devices have been installed.  He remained that way for several minutes... the photo below was my first indication something was wrong.

  

  After waiting for about 3 minutes, it appeared.

  

  Following the instructions, I unplugged and rebooted, uninstalled and reinstalled the software... I have downloaded and run the Print and Scan doctor... he could not solve the problem either ('Unable to communicate scanning pilot' was the last word of the doctor).  On my fifth attempt to re - install the software, I got this result.

  

  I sat and waited, and waited, and the software concluded that she had properly installed, even if the photo above also indicates.  At this point, I can print it, but it takes forever and hesitates when printing as if very little data is done by the intermediary.  If I try to use the scanner via the control center, I get the message not found 'HP imaging device.  Also, sometimes, my computer not turn off unless I turn the printer off (the "Shutting down" message remains on the screen until the printer is turned off).

  And this message was not present at the end of each attempt installation of the printer:

  

  Then... I followed all the instructions (I think), changed USB ports, tried the print and scan doctor... I don't know what else to do.  Been working with it for a day and a half and I'm out of ideas.

  Someone at - it suggestions?

  [Edited 14/07/12]

  One of my friends said that it might be that, since the printer is 6 years old, 64-bit operating system can cause problems and HP probably wouldn't need much resources, writing drivers for everything.  I hope that HP support for their products is better than that.  My Officejet 6310 is not ready to be retired!

  [Published 15/07/12]

  Stop the presses!  I'm a little red-faced now... at some point I have disabled Windows Update (I do not remember doing that, but anyway...) I saw that by accident, turned back on and installed the printer software.  I noticed that Windows Update several files and installation of the driver software window indicated that everything was successful.  BUT... I still have a problem with the scanner, but it's a different error... See the image below.

  

  I can print ok, I can copy ok, but I can't scan with the HP Solution Center or the physical button on the printer.  It is here where I am now.

  If you have spent any time trying to understand the first problem out, I apologize for my lapse in not ensuring that Windows Update has been enabled.  If anyone has any ideas on the situation as it is, please respond here.  Thank you all for research.

  I think I found the problem, although it seems so unlikely for me... I replaced the USB cable and installed the printer software and everything worked fine.  To prove that the cable was at fault, I close the printer down and installed the old cable... the State seemed yet, but when I launched a scan he loses communication before the scan is finished.  I turned off the printer and installed the USB cable replacement and performed the function of scan with no problems.  I repeated this scenario again with the same results... with the original cable (that came with the printer 6 years ago) I had communication errors at the beginning or after a scan.  Installing replacement cable took care of the problem every time.

  How can a cable go bad?  I don't understand this.  In any case, it seems to be fixed now... thanks to all that looked and perhaps thought about my problem.  I guess I'll leave the message here for reference.

• OSX Lion Scanner driver for hp officejet 6100

  I have a pretty old but still works well HP officejet 6100. Is there a driver scanner for mac osx lion?

  Hello
  I'm afraid that scanning is no longer supported by Mac OS X 10.5 and below.

  As you may find listed by the document below under OS X 10.5, the same information applies to any newer OS:

  http://support.HP.com/us-en/document/c01234231

  Kind regards

  Shlomi

• OfficeJet 6500 E709n driver download for printer / scanner link is broken

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=MP-77757-2&cc=us&DLC=en&LC=en&...

  HP Officejet Basic Print and scan driver

  Download link does not work, click on it, displays this error

  This Web page is not found

  Well, it worked. Thank you.

• All-in-one HP Officejet 5610: Scanner not found

  Hello

  I have HP Officejet 5610 all-in-one printing and I use OS X 10.6.8.  I tried to launch the CD supplied with the printer, but that he would be stuck after a few percentage of the installation.  I repeated this process of restarting the laptop and unplug the printer to reset.  Nothing worked so I used the download software/driver online and everything was set up beautifully.  Now, when I tried to analyze one of my papers it says "scanner could not be initialized" because the scanner was not found.

  

  Any help is appreciated, I just need this scanner upward and the work.

  Thank you

  Hello

  The HP Scan Pro is a very old application for Mac SO X 10.4 or 10.5 and not for your current operating system.

  From the Applications folder go to Hewlett-Packard and follow the HP uninstaller program to remove the old software on your Mac.

  Once you are done, download and install the latest version of the software for OS X 10.6 from the following link, then you can scan using the HP scanning software:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=MP-75101-1&cc=us&DLC=en&LC=en&OS=4082&product=441125&sw_lang=

  Kind regards

  Shlomi

• HP officejet d155xi - need driver for windows 2003

  Hi all

  I need your help.

  I have a hp printer officejet d155xi and need to install it in the Windows 2003 operating system but, unfortunately, theres no driver available for Win 2003.

  Are you able to provide me with that. Your help is really appreciated.

  Thank you

  lgeood03

  This problem is already solved. Simply download the Windows XP driver and it works to Windows 2003. Thank you all...

• OfficeJet 4500 Scanner not Fax or copy

  Operating system HP officejet 4500 all-in-one version Windos Vista of origin. message appearing in the lack of window scanner cannot scan, copy or fax

  Please help me solve the problem

• Canon LiDE 700F scanner driver for OS10.11

  Since the El Capitan upgrade my Canon LiDE700f scanner is not recognized.

  I can't find a new driver for OS10.11 on Canon website.

  Any advice?

  Hi Alan_20,

  I understand that you are looking to get your Canon scanner to work with your Mac after upgrade to El Capitan. According to our records, there is software available for this device. It may help to check the software updates (via the Apple menu) before you connect your scanner.

  Look for software updates before connecting your printer or a scanner. This updates the list of the most recent supported on your Mac printer and scanner models. If you do not check the updates before trying to connect a new printer, you won't see the software available when you connect your device.

  Canon CanoScan LiDE 700F *.

  4.1.0a

  S

  Printer and scanner software available for download for your Mac
  https://support.Apple.com/en-us/HT201465

  If you are still unable to get your Mac to recognize your scanner, the next step would be to reset the printing of your Mac system.

  Mac OS X: how to reset the printing system
  https://support.Apple.com/en-us/HT201539

  See you soon!