Open the front panel without toolbar

Similar Questions

• Sub - VI does not open (error 3 could open the front panel)

  I work for the VI (the version of Labview 2011 trail), I created a Subvi. At the same time, I opened this Subvi to adjust terminals connection - what I've done before - and after saving the file and its closure, the Subvi is remained unadjusted. In fact, I am not able to open the Subvi more. And when I want to open the file in a VI (e.g. running VI in windows), I get "' load the error code 3: could not open the front panel." "

  I can't also preform any task for example the recording of the main program for an older version, because this Subvi is present in the program.

  Nevertheless, the VI still works as a Subvi in the mainprogram I wrote - in how it worked until I adjusted the connection terminals.

  Is it possible to solve my problem without having to rewrite the entire Subvi? The Subvi about is attached in this post.

  I thank in advance

  PS. After the closure of Labview, it sends an internal report of the caveat.

  Hi all

  I added this issue to an existing bug report (what we call a request for Corrective Action); There was one reported with Labview 2010. I added this matter to him. The reference of this application is CAR #251753. With this reference, you can always ask the status of this bug report.

  Best regards

• Open the front panel Excel file

  I tried to open an existing to open the front panel button... excel file but looking in the forum I found two examples... attached... done with the document word and another notebook... However I am unable to do it with excel...

  In the second example that uses Sysexec.vi... I tried to enter the path of excel file... but it does not open... but same file opens when I write it on 'Run' in windows vista...

  Advisor...

  I found the solution... using sysexec.vi and the command line...

  

  Thank you...

• Problem: controls and indicators not updated when to open the front panel

  Hello

  I have a strange problem when I progamatically open the façade of a subvi: for some sub-vis controls and indicators are correctly updated while others are not (ie the controls display the outdated values).

  Here, I have created an example that illustrates this. 2 sub-vis are * exactly * the same thing, but only a day watch control when I open it (with the sub - vi previously closed of course).

  How is that possible?

  What should I do to have the controls implemented to date to the last value of the * last call * when I opened the sub - vi?

  
  

• What is going on? Resource not found on the development computer. Error loading VI in lvlib. Load error code 3: could not open the front panel.

  Hello!

  I'm new to libraries of LV and I am compiling my application for the first time with several new lvlib.

  The executable is apparently built without problem, but when I try to run it on the same computer, I get various error messages (4) on the different elements but a single library:

  «LavVIEW: resource not found.»

  "An error occurred loading VI ' LibraryA.lvlib: ItemA.vi '.

  LabVIEW support 3 error code: could not load façade. »

  After that I got the same message for points B, C and D, a final message pops up like this:

  "Missing Subvi LibraryA.lvilib:ItemA.vi in LibraryA.lvilib:CallerX.vi.

  Missing, Subvi LibraryA.lvilib:ItemB.vi in LibraryA.lvilib:CallerX.vi.

  Missing, Subvi LibraryA.lvilib:ItemC.vi in LibraryA.lvilib:CallerX.vi.

  Missing Subvi LibraryA.lvilib:ItemD.vi in LibraryA.lvilib:CallerX.vi. »

  I am not getting any errors for all libraries, so I wonder what is happening.

  So far I have tried:

  -Mass compilation, a few times

  -Check / uncheck 'delete unused library of the project members' and change project after library file removed unused members in the additional Exclusions Page «»

  -Add the screw mentioned in "Still included" in "Source Files".

  When I added the "Always included" screw, I rather got the following (4 times, end to end):

  "The Vi is not executable. The version of LabVIEW full development is necessary to correct the errors. [...]"

  Any other ideas?

  Thank you!

  I have it!

  My problem wasn't a bug compilation of the library at all, but a Scilab Script one.

  The solution can be found here: http://digital.ni.com/public.nsf/allkb/D21F6AC8CFC39E318625756600553B1E

  Thanks for your help, it made me identify!

  Good day!

• is it possible to use the front panel without installing Labview?

  Hallo,

  I have two quick questions:

  1. is it possible to use the façade of a labview software without the need to install Labview itself? I mean something similar to the "power point viewer" that can display Power Point files without installing microsoft office.

  2. in a graphic intensity, how can you change the color?

  Thank you.

  Hello

  What you need to do is

  (1) turn off the interpolation color option

  2) click Add marker, which will add the marker where you want to add

  (3) then right click on the digital value for the marker, you created and you will see the tag, saying: "Color of the mark". Select the color you want.

  In one example, I created values 77 and 23 markers and their red and gray Cap. Hope this helps

  Concerning

• Outsourcing of the controls on the front panel for a panel floating Subvi

  Hello!

  I already found a few similar topics, but I still don't know which is the best way to solve my problem. I will try to describe my problem in detail first: I have a main VI that acquires data from a device and displays these data in a large waveform graph. I have also a few controls on the front panel to control my device. First, I placed all of these device controls (digital, sliders, etc.) as well as the chart inside the front of my main VI. However, due to limited screen space now I would like to make the largest possible graph and so decided to "outsource" some controls out of the main façade of VI to several panels front-end Subvi.

  I would then press a button in my main VI and it would open the Panel before the floating of the Sub - VI corresponding with outsourced controls when required. However, everything must be absolutely transparent. It is important that floating panels to run in parallel with my main VI, that is the main VI must continue to operate. That way I'll have my data constantly updated in the chart in my main VI while I can change some settings of the device through the controls placed in my SubVIs. These changes will be immediately applied (for example as soon as the main VI calls this slot - VI in its main loop).

  It is important to the visibility of the outsourced optional control panel, i.e. If the Subvi front panel opens with the user that it will pop up and the user will be able to change the paramers device using the. But then the user should be able to close the front panel (hide) the Subvi to see the entire chart again without the Panel floating in front of her (of course control values must be maintained when the Subvi front is not visible). Then the new button is pressed in the main VI that opens the dialog box not modal Subvi containing controls and it can redefine new values of device.

  Advice how to do this are welcome. I don't know if I need something complex like VI server or asynchronous screws or I can solve my problem by changing some settings simple Subvi? Thank you in advance for your help!

  Best regards

  Anguel

  AStankov wrote:

  How about using a global variable for the VI at VI communication instead of a queue?

  A global variable will, also.  Write you in one place and read the value frequently to somewhere else (in the election). So you can see easily to any value change.  However, mark will waste a lot of time processor.  This is why I have proposed to use a queue or a notification utility.

  AStankov wrote:

  Would be the last option that you mentioned, i.e. finish the Subvi at each change of value, I would keep the Subvi front open as needed until things from the user to hide? Or would there be inevitable flickering Panel or any other drawbacks?

  Yes, the Subvi can keep the façade open until the user closes. And there should be no flickering.  The biggest drawback I see right now is that when you expect an event in the Subvi, the mainVI cannot stop without talking to the Subvi to stop.  So you'll need another channel of communication (again a global, a queue, a declarant or an event) to tell the Subvi that she must stop.

• How to add a record button on the front panel to save waveform data

  Hi, I'm new kind of LabVIEW and I worked on a code for an agilent oscilloscope communicate via GPIB and so far it works well on the collection of these two analog channels one by one, "Not UNLIMITED" but it does the trick (vpp, Vrms, frequency, etc.).  I've added the feature to add data to a .csv file waveform (problem: opens a dialog box until the user gathers all the data.) Solution: I want the user to save the. File CSV whenever he wants to use later on the front panel). I've added another feature to get a snapshot of the curve waveform (problem: opens a dialog box.) Solution: I want the user to save the JPEG file, whenever he wants to take a snapshot ("take snapshot" button on the front panel)).  I work with the agilent hp54645d driver. I have attached my code, if someone can tell me please how do I do this (maybe cabling and structures are solutions do not know). Thank you in advance.

  I would recommend adding a case structure just around the two record VI and a button to check the condition of the structure of each case. If you want a button to control both save functions you can put the two record functions in the same structure of business controlled by a single button. You are right in saying that the loop will cause your code runs until the stop button is pressed or until the stop condition is met. If you are wanting the while loop to stop once the recorded information you can use the button that you use to control structures case to also stop the while loop. I hope this information helps.

• Cannot resize the front panel

  I can't resize the front panel to a smaller window.  I put in (0,0) minimum window size, unchecked maintain proportions and to scale all objects.  I had originally put the size of the minimum window to 1012 x 616.  When I close the window property and re - open the settings still collated (0,0) while they are saved, but I am unable to reduce the size of window smaller than 1012 x 616.

  Also, there is open space on both sides in both dimensions, so I'm not running in the front panel objects.  What property/properties miss me that locks the minimum panel size?  One last thing is that I'm able to resize windows from any SubVIs I the same project and edit the minimum window size them and they respond as expected.

  Thank you

  Very strange

  comics ctrl + A, ctrl + C, ctrl + N, ctrl + E and ctrl + V solves everything.

  NOR should open with a debugger that vi... Oh where is that entry again heep peek ini thing...

  [Edit: here]

• pause button on the front panel

  Hello.

  I try to run synchronous, continuous analog conversion of 2 cards of PXI-6259, and capture the State of the several digital at the same time.  I managed to get everything is configured and working properly, however I have a problem if the user presses the button "pause" on the front panel.

  From what I can tell, acquisitions of data will continue to run in the background (I'm using a task DAQmx and stop was never called).  For my analog inputs, this is not a problem.  However, the digital inputs always generate a ' 200010 - on-board memory overflow error. Due to the limitations of system and/or the bandwidth of the bus, the driver could not read data the device enough fast to follow the flow of the unit. »

  Is it possible to register for an event of user interface that is generated when the user presses the button "pause", so that I can stop the acquisitoin of data before the error occurs?

  Thanks in advance,

  -Rich

  NormPgh wrote:

  I thought to add my own button "pause" / control, but my users have become accustomed to hitting the pause on the front panel button, and it will be difficult to get them to change.  I guess that the error would remind them :-)

  Well, that's easy to fix - change the appearance of window properties if the toolbar is not visible, while the code runs, and there will be a pause button for your users to click.

  Many of our applications have a function somewhat like this.  My colleague implementation in a very simple way: he put the graphical indicator within a box structure.  Connect a Boolean control "pause" to the structure of the case, and that's it.  Data acquisition runs constantly but will only update the chart when the pause button is false.  This approach might work for you?

• Requirements Gateway - objects on the front panel

  Hello

  I'm about to start using the gateway requirements and I have a few questions to help me go...

  1. If I create a vi on a machine without RG installed and then move it to a machine with the Receiver General installed, will be always recognized tags?

  2 - RG recognize the syntax [covers XX] if it's on a façade and not the block diagram?

  Thanks for your help.

  Darren.

  I know a little RG.

  1. Yes.

  2 RG will scan the three areas of a VI for references: VI Description, control/indicator Description and diagram commentary (free labels). That's why he won't see a reference on the front panel (for example data text or text of the label or a caption).

• Is it possible to call a .exe (non-LabVIEW, such as Notepad) in a child windown on the front panel?

  I would like to launch a stand-alone .exe inside the front of my VI.  It is a piece of software by the provider of a sensor that I try to incorporate in my VI.  I was able to find how to call the .exe using the .NET constructor and invoke nodes.  However, the application opens in its own window.  Is there a way to run from a child window within the façade (ideally, within a tab on the front panel control)?

  I'm in LabVIEW 8.6.

  Thank you.

  smercurio_fc wrote:
  I don't think that it actually works. My understanding is limited about this feature, but since I read it only works with the pop-up windows and windows that are already children. The application's main window is not a child window.

  I've done it before.  I have attached a simple example using Notepad.  Make sure that the notebook is already open no open files.  Since the example is not the position of the child window, the position relative to the window will be the same, because it is off the desk.  So, make sure the upper left corner of the Notepad is close to the origin of the desktop computer.

• Conflict of flow of data on the front panel

  Hello

  My vi is almost done, but I still have a problem with the front panel. I think that there is data traffic conflicts in my vi.

  When you run my vi, you will see the pop-up window asking you to set a path of file, control devices, selection of data to record and trace. Then, you might want to change the units, turn off all the buttons light and ok to select what data you want to save. Then click on RUN.

  The problem is; supposedly all the buttons are on by default, if you disable certain economies or tracing buttons to choose not to save, and then click RUN, after that all the buttons are again even if you have turned off before the race. They must stay off, if you have selected to save. The condition of main data flow is always the same be before running (only light buttons and ok).

  Do you have ideas of how to solve this problem?

  Thanks in advance

  You have what is called a race condition that usually slips in programs that use local variables.  If you look at your first while loop to read in the current value of the 'steam data hand' control and store in a shift register.  After the structure of the event outputs you write this offset value to register in the control and in the process of replacement of the changes that the user can do.

  A quick and dirty solution would be to manage the main event to change the value for 'Stream' in the structure of your event to update the shift register whenever the user changes the values in the control.

  A better solution would be to get rid of the shift registers and move local variables in the structure of the event.  As long as the option "lock the front until the end of the event" (I'm not sure of the exact wording and I work in the LabVIEW Base at the moment so I can't check) is selected it will ensure that you do not work in a race condition (you know the value cannot change inbetween you value reading, and you update the control).

  

  Even better would be to avoid local variables wherever possible.  This is general advice only and not not something that I can do much more tangible without knowing the details of how you want your application to behave.

  Hope this helps,

  Simon

• Want 5530: want to scan from the front panel of the printer computer

  Hello

  I am not able to use the scan to computer function from the front panel of the printer to a PC recently updated.

  On the front panel, I press 'Scan', then 'computer '. The name of the computer to which I want to scan is listed, so I select it. The scan preview screen appears then I press 'analysis '. After a standby display told me that the computer does not have to check the cable, etc...

  The PC is turned on, and the connected user.

  Printer is connected directly to the PC via USB cable.

  PC operating system is Windows 64-bit 10.

  Printer is 5530 want all-in-one.

  HP Print and Scan Doctor no problem.

  I tried with a disabled firewall.

  I uninstalled and reinstalled several times (using a new download of HP).

  When I open the printer software 'manage the scan' is not listed (only the Scan item is 'search for a Document or a picture", that works).

  Test page will print from PC.

  Another PC (running Windows 8.1, connected via a network) seems to work.

  Any suggestions?

  Hello

  Thank you for using the HP Forums.  You can try this:

  Please uninstall and reinstall the software COMPLETE features, follow these steps:

  1 uninstall the software from your computer

  Try this program to uninstall Microsoft

  https://support.microsoft.com/en-us/help/17588/fix-problems-that-block-programs-from-being-installed...

  2. download and save the software COMPLETE features (do not install online)

  The following resources will help you:

  HP printer install wizard for Windows
  http://ftp.HP.com/pub/softlib/software13/COL50403/MP-150580-2/hppiw.exe

  3. install the FULL feature software "saved".

  Once you have downloaded and installed the software, FULL of features, you will be able to print and scan.

  If you are installing via a USB connection, connect the USB cable only when prompted by the software.

  Let us know if it works!

• my hp phtotsmart d110 series is no longer able to scan to PDF from the front panel.

  my hp phtotsmart d110 series is no longer able to scan to PDF from the front panel. How can I solve this problem?

  Hi Jaci17,

  1. open the Solution Center, and then select settings

  2. select scan settings

  3. delete the shortcuts on the right side

  4. click on the device to update, and then close the scan window

  5. open again the scan window

  6. add shortcuts on the left side to the right side

  7. click on the device to update

  8. try scan from the front panel of the printer