Option provisioning VCS key

Similar Questions

• Options in MX700 keys

  Dear community,

  I have a guy on the options available for cisco MX700 keys... We bought a MX700 codec, but the second screen do not work... ! When I go through the option keys intalled, it showed resolution Premium and natural presenter only... Is mi... We need buy a dual display option key to use the second sreen?

  On the other side, this end point have two cameras but only work correctly. The diagnosis shows that the camera is not detected...  Need a few other key option for camera?

  Thanks for your comments.

  What about the King

  You don't need to buy the license option dual display for MX700 because it is integrated into the device aboard the codec. Normally it will not show on installed options because it is a standard feature for MX700 and MX800.

  What do you mean by ' the second monitor do not work? Do you mean no output (wallpaper) screen during the day before? No power? During the active call what you see on the second monitor?

  What are the steps and procedures you already carried out to solve the problem?

  The problem may come from the cable connections on the the second screen (right monitor). Check if the cables are correctly connected according to the installation guide. Refer to step 14 "connect the cables on monitor right and injector PoE" in the title of page 18.

  http://www.Cisco.com/c/dam/en/us/TD/docs/Telepresence/endpoint/MX-series/installation_guide/MX700-DualCam-Floorstand-installation-sheet.PDF

  Also for the camera, no need to option no additional keys for you will activate the second camera. Possibilities would be bad wiring and loose cable connections. Make sure that the cables are connected properly on ports that are appropriate in accordance with the installation guide. Refer to step 16 "cables to Connect camera' to the title on page 21.

  Also, reset the cable connections (unplug and reconnect) on the codec and likely to be untied and disconnected during transportation and installation of the unit. Restart the codec.

  Kind regards

  Acevirgil

• Integration of Lync with VCS - key Option mandatory?

  We implement integration with VCS on x7.2 lync.  Using B2BUA with lync 2010.  Everything works internally with lync configuration, we are only having trouble with lync external participants come and we border routers in the mix.  Direct pools are set up under the name of trust.  We have turned on the highway of the tower.  The calls started from inward of Lync.  VCS sees calls says it is connected, but the appeal does not and then falls normal call clearing.

  My thought for the failure, is that the OCS Collaboration option key has not been added.  But I can't tell in the deployment guide, if this key is necessary only if the encryption is in progress.

  The other area that we now have on the border routers is if The Edge server and the firewall that the Edge transport server may move multimedia traffic through can then reconfigure to allow RTP over UDP and RTP over TCP to pass.

  Can you confirm if the key of the SCO is a requirement for Lync which crosses the highway?  And are there other areas which we recommend why calls set entirely outdoors.

  Hi Kim,

  the SCO cooperation improved option key is necessary for this scenario of appeal, stated at pages 13 and 53 in the Lync to X7.2 deployment guide:

  Calls on a Microsoft Edge server require the VCS have installed improved OCS Collaboration option key because this key allows the ICE to be used for media connectivity

  You are also right that you will need to allow RTP UDP traffic to and from your Edge transport server, as the TURN server on VCS Highway currently does not support the RTP over TCP. If this isn't the case, ice connectivity check between the B2BUA and the Lync client and server Edge fails, which in turn causes to disconnect.

  Hope this helps,

  Andreas

• generates keys option for VCS and VCSE cisco

  Hello team,

  How we generate option keys for cisco VCS and example VCSE under keys of the cisco site.

  LIC-VCS-10

  Video server Comm 10 Add Non-traversal network calls

  Thank you

  Renji

  Hi Renji.

  If you have already purchased the license and then click on the following link and re build.

  https://Tools.Cisco.com/swift/LicensingUI/tandbergLicenseLookup

  If it is not purchased then contact your account key to Cisco for new purchase Manager.

  HTH

  Kind regards

  Dharmmesh

• Command + Option + P + R keys do not work

  Hello world

  I have a 2 models of macbook pro 2010. When I first got them I gave each a password firmware, but for some strange reason, one of them the password does not work! So I need to reset it. I read the forums where it says to remove 1 stick of RAM (fact), reset the SMC (which is), then hold down COMMAND + OPTION + P + R hown to reset the PRAM.

  Problem is to keep these keys does nothing. The macbook starts just to the top as usual. GRRR! It's infuriating! I've tried everything. I also met several other MacBook & macbook pro in the past when he had the chip of ram only 1 I tried to case.have, 2 chips of RAM, Exchange autour, new ram, and 3 other different types of RAM, still the same problem. I have 2 x 2 GB ddr3 1333 mhz in there. I tried chips to 4 gb and 8 gb chips as well. Why the these keys are not suitable? I just don't understand and it's very frustrating because it works just fine on the other macbook pro and the specification and even the model is exactly the same thing...

  I know that the keyboard is OK because the holding CONTROL + OPTION + SHIFT and the power button to do an SMC reset works very well. and Yes, I tried to connect a wired usb macintosh keyboard. These keys do not work either and I know that the keyboard is fine because it works on the imac. I find it confusing that google has no answer for that, surely someone else has had this problem?

  You can reset PRAM with Terminal too: http://osxdaily.com/2015/12/16/view-clear-nvram-mac-command-line-osx/

• The double option of VCS Starterpack Interface!

  Dear all,

  We have a demo system VCS Starterpack with CTI-ATP-VCS-SPAKK9.  I did a software upgrade to X7.2 of X 6.

  Now, I want to use the functionality of Dual Interface and NAT for demonstration of customer but I noticed that there is no Option of Dual Interface on the demo product.

  I tried to find the order ATP for Dual Interface code, but there is not as an option for the product code of CTI-ATP-VCS-SPAKK9.

  What should I do? Does anyone have the same problem?

  Best regards.

  OZBAY Tamer

  Hi Tamer

  You can open the DI for VCS SP option.

  L ATP-VCS-PAK

  -Top level SKU for your VCS StarterPack

  BR Oleksandr

• Option ID CS5 key

  The option key does not work as a modifier with the text tool in ID CS5. I can't do a bullet (Opt-8). However, it works with the selection tool, because I can click on an image, hold down Option and drag to make a duplicate of the image. Everyone knows this? Solutions?

  Same question in PS CS5

  Apple against 10.6.8

  Edit > hotkeys... would be the way that you set up a customized together. I asked because this may be symptomatic of trying to use a game copied from an earlier version of the code.

  I think that if, maybe that's a different problem in your case. Is your browser or as open email? I have a vague memory of a problem with one or the other the key capture.  Are you patched to 7.0.4?

• Satellite L750 - how to find the option of scrolling key?

  Satellite L750

  scroll bars worked yesterday, son played with the computer and now do not come up on top of the screen.

  I went the synaptic pointing device > pointing device Accessories > peripherals > settings > scrolling > finger scrolling

  And the horizontal and vertical boxes are checked.

  But they are not workin?

  Is virtual scrolling option enabled in the settings of the touchpad?

• Question on options for sending key blackBerry Smartphones

  I have a blackberry and all recently changed the Send button.  Before I would be clicking on it I would give recent calls, now when I push the button send, it goes to my contacts list.  I went through all the settings and can't figure out what to do to change it back!

  I have a VAT of blackberry verizon!

  No matter what ould helpw greatly appreciated!

  Justin

  Press your green dial button, then press Menu > Options > General Options.

  Scroll down to the INITIAL VIEW and value that your desired CALL LOG and save.

• Optional provision of FXML GridPane constraints

  Hello
  I'm trying to set columnConstraints on a GridPane in FXML. It works fine for 'hgrow' and "halignment", but it fails for the "margin".
  I do this:

    <columnConstraints>
      <ColumnConstraints hgrow="NEVER" halignment="RIGHT" >
       <margin>
        <Insets bottom="0.0" left="10.0" right="5.0" top="0.0" />
      </margin>
     </ColumnConstraints>
      <ColumnConstraints hgrow="ALWAYS"/>
    </columnConstraints>

  But I get an invalid property exception.
  What I am doing wrong?

  ColumnConstraints is not a property called 'margin '. http://docs.Oracle.com/JavaFX/2/API/JavaFX/scene/layout/ColumnConstraints.html

  In a grid panel, you can set the margin on one using base of the cell by cell (in the Java code) GridPane.setMargin (node, new Insets (...));

  In FXML translates

  
  
  
  
  
  
  
  
  
       
            
  
            
            
       
       
            0
            0
            
                 
            
       
       
            1
            0
            
                 
            
       
       
            0
            1
       
       
            1
            1
       
  
  

• Telepresence PMP license doest work without key option TMSPE?

  Hello

  Telepresence PMP license doest work without key option TMSPE?

  The conductor, we have 250 PMP

  The STM is enabled and uses the license PMP.

  On MSDS, we have the solution for

  -Cisco TMSXE 25
  - and 50 system

  No TMSPE.

  If the use of the PMP license without the option TMSPE (license) key?

  Kind regards

  Antra

  You can install the TMSPE, Smart Scheduler and CMR functions are included for free, no license is required.  The licenses are only required if you plan provisioning VCS registered endpoints.

  TMSPE deployment guides

• Missing option "install the signing keys".

  Hello

  I get "Not registered" errors when going to sign my app RRT & CPR key, so of course that I have a few key signature which are incorrectly installed or not any (signs fine RNR).

  Unfortunately, neither my BlackBerry menus (one out of the meny do a right click on the project itself and that of the Project menu) have the option 'Install Signature keys', no more!

  So, how can I reinstall the signing keys?

  I use the Eclipse Plugin.

  See you soon

  Richard

  Try looking under "Window-> Preferences-> BlackBerry Java Plugin-> Signature Tool"

• The upgrade of control VCS v7.2.2 to 8.1

  Happy new year!

  I saw the 8.1 release notes

  "Before you upgrade to X 8 or later, if you use Agent TMS (legacy mode) for commissioning you must first migrate from Extension Cisco TelePresence Management Suite Provisioning"

  In our VCS, I have the alarm - "Configuration warning - VCS runs in a legacy of the Agent mode TMS;" It is recommended to switch your system to use another mode.

  I guess this VCS was used with an MSD, but now we do not have a.

  How can I get rid of this alarm and upgrade to 8.1 VCS?

  I found that this configuration is the config FindMe, but we have no option to FindMe key now and he is not active.

  I hope that I have explained the problem as clear as possible.

  Best regards

  Kiril

  You can do a factory reset after you be logged in as root, however, he will wipe away everything, including details of intellectual property.

  Your best option is to contact TAC, explain what you want to do and what has kept the data you need and ask them to arrange a re-flash to the system via USB key. (In your case, it seems that you can simply remove the key from the commissioning, however, you should also check that the details of external management have been erased.)

  Edit: See your last post it looks a lot like a factory reset is in order, it will recreate the image on the system and clean the database as well, but like I said above, contact TAC for a re-USB flash file.

  /Jens

  Please note the answers and score the questions as "answered" as appropriate.

• VCS-E in VMware

  Hi all

  Successfully, I downloaded and installed VCS - C in server VM C210. I read there are VCS-E VM image, but I could not find in the download software.  Is any file VCS-E OVA or ISO available?

  Thank you

  Alex

  VM - VCS with demo license (3 registration, course 1 call and 1 non-traversal call) is currently available only VCS-control.

  VM-VCS-Expressway, to purchase Expressway option and install similarly as other key option on VCS that converts the VM - VCS Expressway (activate Expressway on it).

• Client Jabber Viceo registry for VCS/MSDS

  Hello

  I am trying to record a video jabber VCS or TMS customer but his does not work. Whenever I was

  "Bad username, domain and/or password". Check spelling and caps lock.

  Do not know why. Should what I do to register a customer with username and password? VCSC and VCSe are configured for access from inside and outside VCSe.

  Is there a guide for video Jabber clients?

  Best regards

  Jason

  Hi Jason!

  You need a starter pack of VCS-highway or TMS (license + Movi licenses) and a VCS (with the option of commissioning key device).

  As you write VCSe and c its more likely that you do not have the starter pack.

  She has need of configuration and user creation, so it would work not just out of the box.

  The recommended method is the TMSPE, you will find here the deployment guide:

  http://www.Cisco.com/en/us/docs/Telepresence/infrastructure/tmspe/Install_Guide/Cisco_TMSPE_Deployment_Guide_1-0.PDF

  If you have older versions of TMS/VCS you will use it (but I recommend you upgrade and use TMSPE!):

  http://www.Cisco.com/en/us/docs/Telepresence/infrastructure/TMS/config_guide/Cisco_TMS_Provisioning_Deployment_Guide_13-0.PDF

  In addition to this documentation Cisco for TMS, VCS and JabberVideo control.

  TMS:

  http://www.Cisco.com/en/us/products/ps11338/tsd_products_support_series_home.html

  VCS:

  http://www.Cisco.com/en/us/products/ps11337/tsd_products_support_series_home.html

  JabberVideo:

  http://www.Cisco.com/en/us/products/ps11328/tsd_products_support_series_home.html

  Jason: Please note the validations and define the thread if it's an answer!