OptiPlex 780 A15 Bios error 2 and 4

Similar Questions

• Upgrade memory OptiPlex 780

  I bought 2 x 4 GB memory to update my 780 Optiplex originally shipped with only 2 GB. I did some research to make sure that memory, I buy would be compatible with the motherboard. I bought the next memory at amazon:

  www.Amazon.com/.../Ref=oh_aui_detailpage_o00_s00; PSC = 1

  When I put in the new memory, the PC starts normally, fans work and everything, but I have absolutely no video signal to my monitor. When I appear in the old 2 GB, the computer starts normally and I can use it.

  Can you please indicate how do the new memory works, if I have to go into the bios?

  Thank you in advance.

  Then I understood the question, I had to upgrade the Bios A15 and then as soon as I installed the new glue 2x4gb Optiplex 780 automatically their picked up and worked perfectly.

• Tecra S1 starts correctly but does not work properly and beeps from the BIOS error

  Toshiba S1 began to regularly plant after a certain period of use.

  Sometimes: BIOS error beeps: short-short-long.
  Sometimes: Blue screen of reduced resolution or screen size reduced.
  Sometimes: Just freezes (frozen) and must be turned off manually.

  Toshiba uses its own BIOS, no one knows what these sounds average beep or can provide support?
  It is a hardware / connection problem between map chart and monitor or is it an error of memory?

  Hello

  tried to do a memory test? If this isn't the case, I suggest you to do. For these tests, I would prefer to use "memtest86" (www.memtest86.com)
  Otherwise I guess that your motherboard is faulty and you need to bring your machine to a local ASP.

  If you need help to find an ASP, here's a good site:

  http://www.CSD.Toshiba.com/cgi-bin/TAIS/Su/su_gaspLocator.jsp?subs=TAIS

  Good luck
  Welcome them

• HP 15-f305ddx: I haveva hp 15-f305dx with an error code and the password of the bios 58495227

  I have a haveva hp 15-f305dx with an error code and the password of the bios 58495227

  Thank you so much, you're the best

• BIOS error 1 long and 2 short beeps

  Hello

  My Lenovo Thinkpad R61 laptop does not start and gives me those who emits a beep 1 long and 2 short beeps. I found that this beep code is a BIOS error reading file. How can I solve this problem? I try to clear CMOS. I found on the net for phoenix bios, it is possible to fix it with a disk, but I can't find the bios to support from lenovo with a file *. WPH. Anyonw knows where I can find? I really need my computer for work.

  Thank you

  Hello dp88, welcome on the Lenovo forums.

  Please check this thread:

• DM4 0303 and 0305 Bios error saying the disk failure.

  HP Pavilion dm4 - 2033cl Entertainment Notebook PC LW482UAR

  Windows 7 64 bit

  Does not start. BIOS reports an error of hard disk. Diagnostic error 0303 and 0305

  Worked very well. Just finished a "repair" of MS Office Suite, the system asks for a restart, restart it reported this error.

  I tried to turn off, but without success.

  The system is 2 weeks old.

  Hello

  the hard drive failed - so it is under warranty, call HP support and we will send you a HD replacement with installation media

  1 800 HP invent

• New RAM PC3-8500 does not not in Optiplex 780 SFF

  I just bought a pair of 4 GB sticks (F3-8500CL7D-8GBRL) for my Dell Optiplex 780 SFF.

  The manual says it uses DD3-1066, up to 16 GB of 4 connectors.

  During installation and when fired upwards, there is only a sound signal and the diagnostic Dell 1 & 3 lights that indicate: "memory modules are detected, but memory configuration or compatibility error has occurred"
  I tried each module individually in each of the 4 slots (so 8 tries), then the pair 1-3 and 2-4 (more than 2 tests).  No joy.
  When I go back to the original PC3-10600 memory (1 GB + 2 GB) everything works fine.
  I'm on the last BIOS A15. Everyone sees why this RAM will not be happy about this MB...?

  In fact, I managed to add 8 GB to stock / 3GB, so I'm humming 11FR now. The memory that has worked has been Crucial CT2367692. I had to return the other stuff NewEgg taking a shipping and restocking fees kick.

  Lesson learned... I'm always going to Crucial now... obviously, you tell them what machine you have, they guarantee what will work the RAM.

  

• Upgrade to 4 GB Ram problem - computer desktop OptiPlex 780...

  Nice day

  Thank you for your services.

  I am trying to upgrade my desktop computer model # OptiPlex 780 and it's the standard I force the affected elements before, after I check what is the speed of compatible ram, voltage and timing, then I bought this model:

  KHX1333C9D3B1K2 / 8G

  Sound of Kingston - hyper-x blue or you can check the details by the Munificent code above or visiting them this link:

  http://www.Kingston.com/datasheets/KHX1333C9D3B1K2_8G.PDF

  The problem:

  When I delete the original 2 GB Ram and installed this 4 GB ram on the first location, the departure of light 1 # & 3 led with sound as continuous hum without starter or windows interface.

  I tried to:

  -Change the slot

  -Fix the maximum ram which is 4 GB for each slot up to 16 GB

  -Correction of the original 2GB ram in slot 1 then fix the new ram in slot 2 or 3 and 4

  -Update the BIOS to version 15A and update all the drivers from dell.com

  -I make sure that the ram is compatible Guide Dell book on this link:

  http://i.Dell.com/sites/content/business/solutions/engineering-docs/en/documents/OptiPlex-780-tech-guide.PDF

  So please help me in this case, it is urgent and I used this computer in the main office and my work.

  Thanks and regards,

  BYQ-

  svanwormer

  I have a 780 with the Intel E7500, Q45 chipset and A15 BIOS CPU and I'm running 12 GB of DDR3 RAM. Two 4 GB and 2 GB

  Yep, catilley, I'm afraid, you're just wrong on this point - your info is old, apparently.  I, too, running an Optiplex 780 with an Intel Core 2 Quad 9550 CPU, chipset Q45 and 12 GB of DDR3 memory - in fact, it's the same machine that I write this response at this time.

  As I posted a year ago on this thread, the official manual of Service from Dell for Optiplex 780 confirms it will take up to 16 MB of memory DDR3, 4 GB per slot.  Here is the link, directly from the Dell website:

  

• A15 BIOS DON'T SE DOES NOT!

  Sorry, it's all this old stuff, but that's how life is sometimes...

  so, I'm in the process of applying the most recent (and probably last) BIOS update for my OptiPlex 780 SFF faithful, but the new version is not a flash file - it's download, put on a "Startup" disk, and run from there... the problem is there is no "bootable system disk" for windows 7...   This is problem no. 1.

  problem # 2 is, even if I wanted to, how can I make a boot disk?  I even went up to buy one that has a 'guest of the access system' which injects me very politely as x:\ - into a variant of Linux which is be incompatible with BIOS / windows 7 altogether.

  so, I'll give you a big fat cigar to anyone who can solve this one - I can't of course...

  Thank you

  tool_tip

  I agree with you.  I can go with my own experience however in this more modern UEFI/BIOS updates are auto executable.  I will say that if you click on the EXE file and it only unzip that bios file and a readme, then you need to get a bootable flash drive.  You can click here for a Google search on flash bootable drives.

• Dell Optiplex 780 memory update does not

  1. I have purchase Dell Optiplex 780 supplied with memory DDR3 8 GB (4x2Go). I wanted to update so I bought 4 GB RAM (4x1Go) and tried to install it today. The diagnostic lights Dell on 3 and 4, which means that the memory is detected, but at fault. Now, I doubt that this new module of memory are defective. Here's what I did to solve problems:

     I took the original strips and installed a new. There are 4 DIMM and I tried to put it in all the 4 connectors DIMM one, but my PC will not start and shows the Dell diagnostic lights lit 3 and 4. then I put my original RAMS but still the same problem has happened that I also tried the two Rams Original one by one in all the slots but same question :(

     I also tried without installed memory but still Dell lights lit diagnostic 3 and 4 and no beep heard.

     Can someone help me what is the problem real?

  Hi Danish_smartpk,

  Welcome to the Dell Community Forum.

  If the 3 and 4 diagnostic lights are lit, it is code modules of memory detected, but a memory failure that occurred. You also mentioned that there is not only no beeps no heard when no memory is installed. When no memory is detected by the system, it emits beep codes indicating the same.  If the motherboard is not beep when no memory is installed, it could indicate failure systemboard.

  It is generally recommended that the BIOS updated before the new memory being installed. In addition, your computer supports a maximum of 8 GB of RAM DDR3 SDRAM (memory non - ECC only). If it already came with 8 GB of memory, it would not take an additional upgrade.

  If the system is under warranty, contact me with a message private by clicking on my name highlighted in blue. On the next page, click on the envelope icon and provide your service and coordinates (as mentioned below) so that I can access your system folders.

  • System Service Tag No.:
  • Name of the registered owner system:
  • Shipping address:
  • Number of phone/s:
  • E-mail address:

  However, if the system is out of warranty, you can contact a local technician for assistance to the replacement of the motherboard or contact our warranty Support has expired on the link below:

  http://Dell.to/12LmNBq

  Please do not hesitate to contact us in case of other queries.

  Thank you and best regards,
  Babita S
  #iworkforDell

  For easy access to the drivers, manuals and updates, please visit ourSupport Site .

• 2nd disk on Dell OptiPlex 780 Mini-Tower

  I want to install a 2nd SATA Seagate 148 gb SATA HDD on my OptiPlex 780 minitower. The drive is physically mounted in the machine and the power cable that extends from the disk HARD existing fits perfectly in place. I had to go buy a 18 "SATA 7 pin data Cable available from the drive to the motherboard.

  Looks like there are two SATA containers-by-side in the middle section of the motherboard. A feed beige plastic and the other in black.

  Does make a difference that the one that I use?

  Is there another container, should I use instead of these?  Locate where?

  After hanging hardware, what I need to do to get the machine to recognize the new HARD drive when booting?

  Thank you

  The colors are to let you know which port is 0 then 1 then 2, then 3, etc. White port is #3 the orange cable goes from the optical drive sata 1 connector blue is the boot disk which is SATA 0. After connecting the power supply and data, you go into BIOS Setup and turn on SATA2.

  

• Satellite Pro M30 Bios error resource conflict - bios setting change or boot

  Hello.

  My beginning of portable satellite M30 with a bios error. The error that says "resource conflict, the bios setting change or start" If select 'start' the computer crashes before windows starts completely. I have remove the wi - fi and modem module and the same error message. I can't update the bios because the windows start. The bios version is 1.7. The laptop is the UK version. If select "Edit the bios", beginning of the bios but I can't find any resources management.

  Thank you

  (Sorry for my English, I'm from the Spain)

  Hello

  I think the bios error change setting means that you need to access the BIOS and should set the BIOS default settings.

  Please to do this, save the settings and try to start!

• Compaq Presario CQ57: bios error 501

  What should I do to get rid of this problem?  Please help me someone.

  Welcome to the community of HP @ANAKONDA support,

  Thank you for joining on the HP's Support Forums! It is a great place to ask questions, find solutions and get help from others in the community! I read your post on the Forums of HP Support.

  I wanted to join you and help! I understand that you have a problem with an APPLICATION (501) BIOS ERROR on your Compaq Presario CQ57 laptop PC.

  Remove all USB devices. Disconnect all non-essential devices, because they can cause some problems.

  Try starting your laptop normally after having disconnected all. If that does not solve the problem, please continue with troubleshooting.

  The next step would be for you to try to restore the BIOS. You will see that the document says:

  If the BIOS of your laptop becomes corrupted, and a failure to upgrade the BIOS or damage caused by a virus, the computer can display all the following symptoms:

  • The computer displays the error message from the BIOS APPLICATION ERROR 501.

  After restoring the BIOS see if you can start the computer normally.

  Thank you for your participation in the Forums of HP where we want to help you as well as others who may encounter a similar problem that you have. Remember to mark this message as an acceptable Solution if it solves the problem for you.

  To show recognition for my efforts please click the Thumbs Up below.

  If you need assistance, I would be more than happy to continue to help you. Please re-post with the results of the resolution of the problems. Could you please also provide your model number (How can I find my model number or product number?)

  Have a wonderful day!

• EliteBook 8570p: BCU and SCCM 2012 WinPE10 error 0x0000000A and task sequence 0x0000000B

  I am trying to run an OSD task sequence in SCCM 2012 to set the BIOS Setup, secure TPM activation and switching to native mode UEFI in preperation for BitLocker, then BIOS password setting all of in WinPE. The command below works fine when connected to the laptop in full Windows 10 cmd prompt, but for some reason I get and error when trying to run task sequence command.

  Using the version of the NBU: 4.0.13.1

  Version of WinPE 10 x 64: 10.0.10240.16384

  "' RunBCU.cmd /setconfig:"Config\8570pconfig.repset' /cspwdfile:"Config\oldpassword.bin ' /nspwdfile:"Config\newpassword.bin '.

  Where are the log files of the utility?

  What does the error 0x0000000A and 0x0000000B?

  What Miss me?

  Any help would be much appreciated. Thank you.

  Please, look at the white paper following developed to help understand how to manage the TPM and also not recommended for SCCM

  http://FTP.HP.com/pub/caps-SoftPaq/CMIT/whitepapers/building, %20Deploying,%20and%20Updating%20an%20Image%20on%20HP%20Commercial%20PCs.pdf

  other whitepapers are available from www.hp.com/go/clientmanagement

  BTW, it seems that you must set the pwd BIOS FRONT to manage the TPM

• PASSWORD OF BIOS ERROR CNU9423W4T

  PASSWORDS FOR BIOS ERROR CNU9423W4T? WHT is my password

  Try Fran's.

  e9lov7fdva

  3rd letter tiny L.

  4th letter lowercase O.

  Use this code to go into the BIOS.

  Disable all passwords that are enabled.

  IF demand for CURRENT password using this code.

  REQUEST NEW password just press ENTER.

  If asked to hit just to CHECK password to enter.

  Save and exit.

  REO

  I must inform you that these services are not endorsed by HP, and that HP is not responsible for any damages that may occur to your system using these services. Please be aware that you do so at your own risk.