OSB 11 g dynamic routing number

Similar Questions

• PIX515 & dynamic routing

  Central office:

  LAN - 10.20.0.0 255.255.255.0

  PIX 515 - int branches - branches (through the cloud of MPLS VPN)

  internal int - LAN

  int outdoors - WAN

  Branch:

  LAN - 10.20.16.0.255.255.255.0

  C1760 - int s0/0 - Central officr (through the cloud of MPLS VPN)

  PIX501 - int outdoors - WAN

  internal int - LAN

  The PIX515, I had a static route to the path to service-

  Route of the branches 10.20.16.0 255.255.255.0 192.168.16.1 1

  I want up VPN channel between PIX501 (int outside) of the Executive Board and the Central PIX515(int outside).

  To do this, I created card crypto to PIX515 and ACL:

  outside_crypto_map_10 ip 10.20.0.0 access list allow 255.255.255.0 10.20.16.0 255.255.255.0

  card crypto 10 TEST matches the address outside_crypto_map_10

  Here my question: I want to remove static route of PIX515 and use dynamic routing, but I hesitated because I have ACLs for VPN, where branch destination LAN (and will serve as an int on the outside) and dynamic road that shows the way to the domestic LAN through branches int PIX515. How this will be live together? And what will be used first - road or ACL?

  The PIX can run RIP and OSPF today, but not those of a VPN. If you want to learn routes dynamically through the VPN you can do that, so you need to use static routes instead. Looks like you might be interested by the DMVPN function in IOS routers.

  Routing, regarding all the traffic that you want to use a VPN must first be routed on an interface that has the appropriate encryption card applied, then if this traffic matches an ACL encryption card it will be encrypted and sent to the corresponding VPN peer. That's to say routing goes first for the outbound VPN traffic, then encryption. No matter if channels are static or learned dynamically, except, as I mentioned above, you can now run a routing through a VPN Protocol in the PIX.

  Does that help?

• Dynamic routing for VPN Failover L2L

  Hello

  Can someone offer me some advice on this please?

  I have attached a simple diagram of our EXTENSIVE referral network.

  Overview

  • The firewall is ASA 5510 running 8.4 (9)
  • Basic to the Headquarters network uses OSPF
  • On ASA static routes are redistributed into OSPF
  • On ASA for VPN static routes are redistributed into OSPF with 130 metric so redistributed BGP routes are preferred
  • Basic network has a static route to 10.0.0.0/8 to Corporate WAN, which is redistributed into OSPF
  • Branch Office WAN uses BGP - routes are redistributed into OSPF
  • The branch routers using VRRP for redundancy of the IP for the default gateway of local customers.
  • Branch router main past off VRRP IP to router backup when the WAN interface is down
  • BO backup router (. 253) contains only a default route to the internet
  • In normal operation, the traffic to and from BO uses Local Branch Office WAN
  • If local BO WAN link fails, traffic to and from the BO uses IPSec VPN via public Internet

  I try to configure dynamic routing on our network for when a branch switches to the IPsec VPN. What I want to happen (not sure if it is possible) is for the ASA announce the subnet to the remote end of the VPN in OSPF to Headquarters.

  I managed to get this working using IPP, but for some reason any VPN stay up all the time when we are not in a failover scenario. This causes the ASA added the table as a static route is the remote subnet in it and do not use the announced route of OSPF from the core network. This prevents the BO customers access to the Internet. If I remove the IPP on the VPN setting, ASA learns the route to the subnet via the WAN BO - resumes normal operation.

  I have configured the metric of the static routes that get redistributed into OSPF by ASA superior to 110. This is so that the routes redistributed by the WAN BO OSPF BGP, are preferred. The idea being that when the WAN link is again available, the routing changes automatically and the site fails to WAN BO.

  I guess what I need to know is; This design is feasible, and if so where I'm going wrong?

  Thank you

  Paul

  Hi Paul,.

  your ASA maintains the tunnel alive only because this path exists on ASA.  This is why you must use IP - SLA on ASA to push network taffic "10.10.10.0/24" based on the echo response, using the ALS-intellectual property

  Please look at the example below, in the example below shows that the traffic flows through the tunnel, only if the ASA cannot reach the 10.10.10.0/24 network via the internal network of HQ.

  This configuration illuminate ASA.

  Route inside 10.10.10.0 255.255.2550 10.0.0.2 track 10

  (assuming 10.0.0.2 ip peering from inside the ip address of the router to HO)

  Route outside 10.10.10.0 255.255.255.0 xxx.xxx.xxx.xxx 254

  (value of 254 is a more expensive route to go via IPSec tunnel and x = the bridge by default-ISP)

  ALS 99 monitor

  type echo protocol ipIcmpEcho 10.10.10.254 inside interface

  NUM-package of 3

  frequency 10

  Annex monitor SLA 99 life never start-time now

  track 10 rtr 99 accessibility

  Let me know, if this can help.

  Thank you

  Rizwan James

• Difference between dynamic and dynamic routing issue

  Hello
  
  Can someone let me know the difference between dynamic routing and dynamic publishing in the oracle service bus
  
  Thank you
  Barro

  Hello

  If the outgoing end point is not static or Exchange with the incoming request again for dynamic actions...

  Routing is used for calls for installation (who have asked and answer) that is routing action awaits the response before going to the pipeline of response
  Publish is used for asynchronous calls (which does not hv any answer).

  See you soon,.
  Afonso Gupta

• is there any function in the osb to generate a unique number in proxy

  is there any function in the osb to generate a unique number in proxy

  FN - bea: uuid()

  The function fn - bea: uuid() returns a universal unique identifier. The function has the following signature:

  FN - bea: uuid() as XS: String

  You can use this function in the pipeline of proxy to generate a unique identifier. You can insert the unique identifier that is generated in an XML document in the form of element. You are unable to generate a unique identifier to the system variable. You can use this to edit a message payload.

  For example, suppose you want to generate a unique identifier to add it to a message for follow-up purposes. You can use this function to generate a unique identifier. The function returns a string that you can add it to the SOAP header.

• Dynamic routing? How to play files on 2 different directories?

  I need to do... recover files but 2 different places...
  
  a simple idea?
  
  Yes, the easiest is to have 2 bpels listenening in each directory...
  
  I can create only 1 BPEL?
  
  I heard... too complex dynamic routing?
  
  Thank you!
  Pablo.

  You really need 2 BPEL process as you said. I have not tried, but BSE may be able to have 2 adapters incoming to map it to a BPEL process.

  Dynamic routing is more outgoing, not falling.

  see you soon
  James

• OSB 12 & dynamic route: $operation is empty

  I'm migrating a project of OSB 11 g to 12 c and encountered a problem.

  The project has a part where a proxy call another proxy via a DR.

  For example:

  Proxy entry:

  1. service of routing XML forms, for example:

  < = xmlns:ctx ctx:route' http://www.BEA.com/WLI/SB/context '>

  < ctx:service proxy = "true" > DR-with-operation/Destination < / ctx:service >

  {$operation} < ctx:operation > < / ctx:operation >

  < / ctx:route >

  2 call the local proxy of destination.

  Destination proxy:

  1 read the $operation and executes an action based on its value.

  Now, the question: proxies use the same WSDL and WSDL has the same top element for all applications. Therefore, the selection of the operation of SOAP - env:Body is not possible. The selector is set to SOAPAction, which is NOT right - nobody sent SOAPAction to the second proxy - but it works in OSB 11 because $operation in the second proxy corresponds to the value set in ctx:route by the first proxy.

  No more the OSB 12. The OSB 12 the $operation is empty. Thus the code fails.

  Here is a minimal test project to reproduce the case: http://genericparallel.com/wp-content/uploads/2014/07/DR-With-Operation.zip

  Of course, I could pass through the head of a transport operation, but my example is a simplification of the actual design. The first proxy in my case is a shared code that is used to call hundreds of different proxy servers. I don't want to inject everything with a transport header arbitrary that they do not need. Ideally, I'd like that the $operation is filled in the same way as before.

  Does anyone have an idea about this problem?

  Vlad

  < signature link removed by the moderator, as directed by the OTN FAQ >

  Try this for your case

  DR-with-operation/Destination

  {$operation}

  Greg

• Dynamic routes on a FWSM

  Hello

  Does anyone know how many routes (OSPF) dynamic a FWSM can handle. I can´t find this information on the website, so if you know a link that specifies this I´d much enjoy it.

  Thank you.

  The following link has information:

  http://www.Cisco.com/univercd/CC/TD/doc/product/LAN/cat6000/mod_icn/FWSM/fwsm_2_3/fwsm_cfg/specs.htm#wp1054770

  32000 routes Dynamics max (in all contexts).

• Ontario Regulation distributes dynamic routes via VPN S2S

  Hi halijenn / experts

  (1) please let me know if IPP works on a Site in tunnel

  (2) I have a behind remote ASA 10.10.1.0 and 10.10.2.0 network that must be distributed to another branch ASA with S2S ASA remote via OSPF

  3) there is an L3 Switch behind the ASA of the branch and Switch L3 there is a router that has a default route pointing router WAN

  Router WAN
  |
  |
  Users-> router-> L3 Switch-> ASA-> Internet-> remote ASA branch (10.10.1.0, 2.0)

  Note: 10.10.1.0 2.0 AND are already configured in the ACL Crypto at the ends.

  Users are able to reach the 10.10.2.X network to the remote end.

  Now for the 10.10.2.0 static routes are already there in the router and the switch finally pointing the ASA branch however as the network grows, it is impossible in the router behind the switch to add static whenever routes (such as the default route to router WAN points). This is why in order to learn routes dynamically, I will add an ospf process to the ASA to branch with the following configuration. Please let me know if iam correct when I add IPP and other OSPF commands to the ASA of the branch. (hope I have nothing to do on ASA remote associated with IPP or OSPF?)

  I take just an example of a remote host 1 10.10.1.4. Inside ASA interface leading to users is 172.16.1.0/24

  access-list redistribute allowed standard host 10.10.1.4 255.255.255.255

  router ospf 1
  network 172.16.1.0 255.255.255.0 area 0
  Journal-adj-changes
  redistribute static subnets redistribute route map

  In addition, I will also be allowing the order for IPP in the encryption of the VPN S2S said card.

  Please help me understand if I'm wrong

  Pls set the OSPF firstly on the SAA process before removing the static routes. Once you have confirmed that the OSPF is configured correctly and the roads are in the OSPF database, then you can delete the static routes. Static routes will always take precedence over OSPF because it has higher metric. Please keep the default route configured on the SAA.

  Hope that confirms it.

• Dynamically change number of records displayed in the block to the runtime

  Hello
  I would like to implement the treatment where I get a (whole) number in a field (i.e. 3) and then I should have 3 records in a block
  
  I want to know if it is possible to change dynamically during execution (via the trigger of this point) where I managed the record count displays the property.
  
  I searched through set_block_property (a, b, c), but did not find the corresponding property_name to manage as appropriate.
  
  Thank you in advance for your return;

  Cannot set the number of records displayed the runtime property.

  see you soon

• Adding interface routed in the State of dynamic routing

  I have a 3560 which hangs a 6509. The next SVI s direct on the 3560:

  192.168.181.1(VLAN 192.168.180.1 (VLAN 180), 181), 192.168.182.1 (VLAN 182), 192.168.183.1 (VLAN 183), 192.168.184.1 (VLAN 183).

  I want to create the router eigrp statement that says:

  Router eigrp 777

  network 192.168.180.0 0.0.0.225

  network 192.168.181.0 0.0.0.225

  network 192.168.182.0 0.0.0.225

  network 192.168.183.0 0.0.0.225

  network 192.168.184.0 0.0.0.225

  Now for the routed on the 3506 interface that is 192.168.0.17 can I create a statement of routing for the and it's as simple as network 192.168.0.17 0.0.0.3?  What of the other side do I add network 192.168.0.17 0.0.0.3 in the instruction of network on the 6509?

  Jon isn't that statement back? If it shouldn't be 192.168.0.16 0.0.0.3?

  My mistake, you are right, it should be as you say.

  Sorry about that :-)

  Jon

• ASA - IOS VPN dynamic routing

  I saw the docs that show how to configure ASA-ASA VPN share OSPF routes and for IOS to IOS OSPF sharing routes. Is it possible to get the ASA to IOS device?

  I'm supposed to put in place a DMVPN through some remote sites, and there is an ASA one of the sites. The EIGRP routes are expected to be shared across the DMVPN (I suppose could go to OSPF if necessary). My plan for the site of the SAA was to set up a VPN site-to-site regular with the DMVPN hub and redistribute OSPF and EIGRP routes in the other, so the rays can talk to the ASA branch by the hub.

  Is it possible, or I have to use static routes to and from the network of the ASA?

  Xavier,

  In the road map you must place a match statement corresponding prefixes/subnets that you would like to advertise in EIGRP.

  About the ASA, normally you have not to, but I don't see a problem with the addition of statements of IPP in crypto card (normally).

  With regard to orders. I always refer people to self-help ;-)

  http://www.Cisco.com/en/us/products/ps10591/products_product_indices_list.html

  more precisely:

  http://www.Cisco.com/en/us/docs/iOS/MCL/allreleasemcl/all_book.html

  Docs IPP:

  http://www.Cisco.com/en/us/docs/iOS/sec_secure_connectivity/configuration/guide/sec_rev_rte_inject_ps10592_TSD_Products_Configuration_Guide_Chapter.html

  Redistribution of EIGRP:

  http://www.Cisco.com/en/us/docs/iOS-XML/iOS/iproute_eigrp/configuration/15-1mt/Configuring_EIGRP.html#GUID-1D5F3B6E-B89A-497A-BBC4-98C4A4E21CE7

  In any case take step by step, start by checking what the situation will be when you insert routes into the routing on the hub by RRI table. Then, if necessary, redistribute static routes in EIGRP.

  Marcin

• VPN site to Site with dynamic routing on ASAs

  I'm planning a backup connection to a primary site if our link main broken through two ASAs using site to site vpn.

  This is what I have resulted to date and just need to work through some issues and best practices.

  ##Regular connectivity and Internet traffic flow "> Primary_Internet".

  Backup_Internet - ASA - CoreA - router-->> Private_Wan<>

  ?? If Private_Wan a link down, use via ASA l2l Internet VPN to connect sites

  x - router - CoreA - ASA-->> VPN l2l<>

  ?? Once the link is available, preferred over the private Wan path must be used.

  A few questions,

  1. can I use a routing via the l2l VPN Protocol? VTI, GRE?

  2. If I enter OSPF or EIGRP, will be the last static use of each work in the ASA redistibuting?

  3. in execution of VPN l2l, using 'show the way' does not show available via the vpn routes, only "crypto ipsec to show his" watch info. Is this correct? If yes how metric would work for routes registered if all the links are up and there are many paths to the same subnet?

  Welllll,

  (2) I would keep as simple as possible, you can put all one VPN perhaps NSSA, if your ASA touch BB.

  (3) IPP on ASA is always the insertion of static routes, it is not the best way to generate the backup.

  Marcin

• Dynamic action - number of events triggers

  See http://screencast.com/t/XrGTYvKFT
  
  The DA is a search server side based on the content of a form input field when the field gets focus.
  
  Is it possible to trigger the DA on either a KeyRelease event or get a tune-up? It would cover both use cases, initial entry and reviewing data that already exists.
  
  Ideas? Thank you
  
  [Of course, I could just duplicate the DA and set one of them to shoot the KeyRelease and the other on GotFocus, but this is not < a href = "http://en.wikipedia.org/wiki/Don%27t_repeat_yourself" > < /a > SEC]

  Vikas,
  It would have been much easier if the events themselves might have been entered in definition (wizard) D.A., so that several events as well a custom events trigger a D.A.

  As for your question, a (convoluted) way is to use an intermediate element of the set.

  Want to trigger a D.A. on 'KeyRelease' and 'Get the Focus'.

  Add a hidden element somewhere on the page (element text pre/post, headers region, region html etc...)

  < span id = "my_elem" > & template; </span >

  You can then set the D.A. triggered by a click (double click or any event that D.A. support natively) on this element.

  Then you link the original events on any element to trigger the event of the item to the D.A. (and therefore the D.A.)
  You can add an onload J.S / an another D.A. for that.
  The code reads

  $('selector').bind('event-names',function(){
    $('#my_elem').trigger('eventname');
  });
  

  for example

  $('P1_ITEM1').bind('keyup,focus',function(){
    $('#my_elem').trigger('click');
  });
  

• can we use service legend to dynamically call business service in OSB

  My requirement is: contact service issue. moments of for - each loop in OSB. Node road that we cannot use in the foreach loop.

  can we use service legend to call business several times? and how can we pass endpoint url to business service using the legend of service.

  Please help me.

  Yes you can use routing options to override the legend service endpoint url. See

  http://docs.Oracle.com/CD/E23943_01/admin.1111/e15867/proxy_actions.htm#i1315299

  The action of routing Options can be used when the context variable $outbound is valid. It can be added to the following actions:

  • Publish
  • Dynamic publishing
  • Publish the Table
  • Legend of service
  • Routing
  • Dynamic routing
  • Routing table